diff options
Diffstat (limited to 'util/romcc/tests/raminit_test1.c')
| -rw-r--r-- | util/romcc/tests/raminit_test1.c | 110 |
1 files changed, 55 insertions, 55 deletions
diff --git a/util/romcc/tests/raminit_test1.c b/util/romcc/tests/raminit_test1.c index 2c6fa8c750..569d75ba62 100644 --- a/util/romcc/tests/raminit_test1.c +++ b/util/romcc/tests/raminit_test1.c @@ -136,7 +136,7 @@ void uart_wait_to_tx_byte(void) void uart_wait_until_sent(void) { - while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40)) + while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40)) ; } @@ -355,7 +355,7 @@ int smbus_read_byte(unsigned device, unsigned address) /* CAS latency 2 */ #if (CAS_LATENCY == 2) #define CAS_NB 0x17 - /* + /* * 7 == 0111 * 1 == 0001 */ @@ -367,7 +367,7 @@ int smbus_read_byte(unsigned device, unsigned address) #endif /* CAS latency 3 */ -#if (CAS_LATENCY == 3) +#if (CAS_LATENCY == 3) #define CAS_NB 0x13 /* * 3 == 0011 @@ -381,11 +381,11 @@ int smbus_read_byte(unsigned device, unsigned address) #endif #ifndef CAS_NB -#error "Nothing defined" +#error "Nothing defined" #endif /* Default values for config registers */ - + static void set_nbxcfg(void) { /* NBXCFG 0x50 - 0x53 */ @@ -417,7 +417,7 @@ static void set_nbxcfg(void) * ECC Diagnostic Mode Enable == 0 Not Enabled * MDA present == 0 Not Present * USWC Write Post During During I/O Bridge Access Enable == 1 Enabled - * In Order Queue Depth (IQD) (RO) == ?? + * In Order Queue Depth (IQD) (RO) == ?? */ pcibios_write_config_dword(I440GX_BUS, I440GX_DEVFN, 0x50, 0xff00000c); } @@ -486,7 +486,7 @@ static void set_mbsc(void) * MD[63:0]# Buffer Strength Control 1 == 3x * MECC[7:0] Buffer Strength Control 2 == 3x * MECC[7:0] Buffer Strength Control 1 == 3x - * CSB7# Buffer Strength == 3x + * CSB7# Buffer Strength == 3x * CSA7# Buffer Strength == 3x * CSB6# Buffer Strength == 3x * CSA6# Buffer Strength == 3x @@ -575,13 +575,13 @@ static void set_pgpol(void) static void set_mbfs(void) { /* MBFS - Memory Buffer Frequencey Select Register */ - /* 0xffff7f - * [23:20] f == 1111 - * [19:16] f == 1111 - * [15:12] f == 1111 - * [11: 8] f == 1111 - * [ 7: 4] 7 == 0111 - * [ 3: 0] f == 1111 + /* 0xffff7f + * [23:20] f == 1111 + * [19:16] f == 1111 + * [15:12] f == 1111 + * [11: 8] f == 1111 + * [ 7: 4] 7 == 0111 + * [ 3: 0] f == 1111 * MAA[14:0], WEA#, SRASA#, SCASA# == 100Mhz Buffers Enabled * MAB[14,13,10,12:11,9:0], WEB#, SRASB#, SCASB# == 100Mhz Buffers Enabled * MD[63:0] Control 2 == 100 Mhz Buffer Enable @@ -622,12 +622,12 @@ static void set_drtc(void) static void set_pmcr(void) { - /* PMCR -- BIOS sets 0x90 into it. + /* PMCR -- BIOS sets 0x90 into it. * 0x10 is REQUIRED. * we have never used it. So why did this ever work? */ pcibios_write_config_byte(I440GX_BUS, I440GX_DEVFN, 0x7a, 0x90); - + } void sdram_set_registers(void) { @@ -651,7 +651,7 @@ void sdram_set_registers(void) int log2(int value) { /* __builtin_bsr is a exactly equivalent to the x86 machine - * instruction with the exception that it returns -1 + * instruction with the exception that it returns -1 * when the value presented to it is zero. * Otherwise __builtin_bsr returns the zero based index of * the highest bit set. @@ -670,7 +670,7 @@ static void spd_set_drb(void) unsigned end_of_memory; unsigned device; unsigned drb_reg; - + end_of_memory = 0; /* in multiples of 8MiB */ device = SMBUS_MEM_DEVICE_START; drb_reg = 0x60; @@ -704,13 +704,13 @@ static void spd_set_drb(void) #else side1_bits += log2((byte2 << 8) | byte); #endif - + /* now I have the ram size in bits as a power of two (less 1) */ /* Make it mulitples of 8MB */ side1_bits -= 25; - + /* side two */ - + /* number of physical banks */ byte = smbus_read_byte(device, 5); if (byte > 1) { @@ -783,8 +783,8 @@ static void spd_set_dramc(void) } dramc = 0x8; if ((byte & 0x12) != 0) { - /* this is a registered part. - * observation: for register parts, BIOS zeros (!) + /* this is a registered part. + * observation: for register parts, BIOS zeros (!) * registers CA-CC. This has an undocumented meaning. */ /* But it does make sense the oppisite of registered @@ -835,7 +835,7 @@ static void spd_enable_refresh(void) } byte &= 0x7f; /* Default refresh rate be conservative */ - refresh_rate = 5; + refresh_rate = 5; /* see if the ram refresh is a supported one */ if (byte < 6) { #if HAVE_STATIC_ARRAY_SUPPORT @@ -856,7 +856,7 @@ static void spd_set_sdramc(void) static void spd_set_rps(void) { /* - * Effects: Uses serial presence detect to set the row size + * Effects: Uses serial presence detect to set the row size * on a given DIMM * FIXME: Check for illegal/unsupported ram configurations and abort */ @@ -881,16 +881,16 @@ static void spd_set_rps(void) page_size = byte & 0xf; /* make it in multiples of 2Kb */ page_size -= 11; - + if (page_size <= 0) continue; - + /* FIXME: do something with page sizes greather than 8KB!! */ page_sizes |= (page_size << index); - + /* side two */ byte = smbus_read_byte(device, 5); if (byte <= 1) continue; - + /* For now only handle the symmetrical case */ page_sizes |= (page_size << (index +2)); } @@ -898,10 +898,10 @@ static void spd_set_rps(void) /* we have just verified that we have to have this code. It appears that * the registered SDRAMs do indeed set the RPS wrong. sheesh. */ - /* at this point, page_sizes holds the RPS for all ram. - * we have verified that for registered DRAM the values are + /* at this point, page_sizes holds the RPS for all ram. + * we have verified that for registered DRAM the values are * 1/2 the size they should be. So we test for registered - * and then double the sizes if needed. + * and then double the sizes if needed. */ dramc = pcibios_read_config_byte(I440GX_BUS, I440GX_DEVFN, 0x57); @@ -909,9 +909,9 @@ static void spd_set_rps(void) /* registered */ /* BIOS makes weird page size for registered! */ - /* what we have found is you need to set the EVEN banks to - * twice the size. Fortunately there is a very easy way to - * do this. First, read the WORD value of register 0x74. + /* what we have found is you need to set the EVEN banks to + * twice the size. Fortunately there is a very easy way to + * do this. First, read the WORD value of register 0x74. */ page_sizes += 0x1111; } @@ -938,8 +938,8 @@ static void spd_set_pgpol(void) bank_sizes = 0; bank = 0; device = SMBUS_MEM_DEVICE_START; - for(; device <= SMBUS_MEM_DEVICE_END; - bank += 2, device += SMBUS_MEM_DEVICE_INC) { + for(; device <= SMBUS_MEM_DEVICE_END; + bank += 2, device += SMBUS_MEM_DEVICE_INC) { int byte; /* logical banks */ @@ -947,7 +947,7 @@ static void spd_set_pgpol(void) if (byte < 0) continue; if (byte < 4) continue; bank_sizes |= (1 << bank); - + /* side 2 */ /* Number of physical banks */ byte = smbus_read_byte(device, 5); @@ -974,14 +974,14 @@ static void spd_set_nbxcfg(void) /* Say all dimms have no ECC support */ reg = 0xff; index = 0; - + device = SMBUS_MEM_DEVICE_START; for(; device <= SMBUS_MEM_DEVICE_END; index += 2, device += SMBUS_MEM_DEVICE_INC) { int byte; byte = smbus_read_byte(device, 11); if (byte < 0) continue; -#if !USE_ECC +#if !USE_ECC byte = 0; /* Disable ECC */ #endif /* 0 == None, 1 == Parity, 2 == ECC */ @@ -1015,7 +1015,7 @@ static void spd_set_nbxcfg(void) /* try this. * We should be setting bit 2 in register 76 and we're not * technically we should see if CL=2 for the ram, - * but registered is so screwed up that it's kind of a lost + * but registered is so screwed up that it's kind of a lost * cause. */ byte = pcibios_read_config_byte(I440GX_BUS, I440GX_DEVFN, 0x76); @@ -1098,7 +1098,7 @@ static void dimms_read(unsigned long offset) int i; for(i = 0; i < 8; i++) { unsigned long dummy; - unsigned long addr; + unsigned long addr; unsigned long next_base; next_base = dimm_base(i +1); @@ -1108,8 +1108,8 @@ static void dimms_read(unsigned long offset) } addr += offset; #if HAVE_STRING_SUPPORT - print_debug("Reading "); - print_debug_hex32(addr); + print_debug("Reading "); + print_debug_hex32(addr); print_debug("\n"); #endif #if HAVE_POINTER_SUPPORT @@ -1120,8 +1120,8 @@ static void dimms_read(unsigned long offset) #endif #endif #if HAVE_STRING_SUPPORT - print_debug("Reading "); - print_debug_hex32(addr ^ 0xddf8); + print_debug("Reading "); + print_debug_hex32(addr ^ 0xddf8); print_debug("\n"); #endif #if HAVE_POINTER_SUPPORT @@ -1132,9 +1132,9 @@ static void dimms_read(unsigned long offset) #endif #endif #if HAVE_STRING_SUPPORT - print_debug("Read "); - print_debug_hex32(addr); - print_debug_hex32(addr ^ 0xddf8); + print_debug("Read "); + print_debug_hex32(addr); + print_debug_hex32(addr ^ 0xddf8); print_debug("\n"); #endif } @@ -1212,9 +1212,9 @@ void sdram_enable(void) #if HAVE_STRING_SUPPORT print_debug("Ram Enable 2\n"); #endif - + /* Now we need 8 AUTO REFRESH / CBR cycles to be performed */ - + sdram_set_command_cbr(); sdram_assert_command(); sdram_assert_command(); @@ -1224,11 +1224,11 @@ void sdram_enable(void) sdram_assert_command(); sdram_assert_command(); sdram_assert_command(); - + #if HAVE_STRING_SUPPORT print_debug("Ram Enable 3\n"); #endif - + /* mode register set */ sdram_set_mode_register(); /* MAx[14:0] lines, @@ -1245,7 +1245,7 @@ void sdram_enable(void) /* normal operation */ sdram_set_command_none(); - + #if HAVE_STRING_SUPPORT print_debug("Ram Enable 5\n"); #endif @@ -1270,7 +1270,7 @@ void sdram_initialize(void) print_debug("Ram3\n"); #endif /* Now that everything is setup enable the SDRAM. - * Some chipsets do the work for use while on others + * Some chipsets do the work for use while on others * we need to it by hand. */ sdram_enable(); |