summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-04-01boot: add disable_cache_rom() functionAaron Durbin
On certain architectures such as x86 the bootstrap processor does most of the work. When CACHE_ROM is employed it's appropriate to ensure that the caching enablement of the ROM is disabled so that the caching settings are symmetric before booting the payload or OS. Tested this on an x86 machine that turned on ROM caching. Linux did not complain about asymmetric MTRR settings nor did the ROM show up as cached in the MTRR settings. Change-Id: Ia32ff9fdb1608667a0e9a5f23b9c8af27d589047 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2980 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01lynxpoint: Basic configuration of SerialIO devicesDuncan Laurie
This adds configuration of SerialIO devices in the Lynxpoint-LP chipset. This includes DMA, I2C, SPI, UART, and SDIO controllers. There is assorted magic setup necessary for the devices and while it is similar for each device there are subtle differences in some register settings. These devices must be put into "ACPI Mode" in order to take advantage of S0ix. When in ACPI mode the allocated PCI BARs must be passed to ACPI so it can be relayed to the OS. When the devices are in ACPI mode BAR0+BAR1 is saved into ACPI NVS and then updated and returned when the OS calls _CRS. Note that is is not entirely complete yet. We need to update the IASL compiler in our build environment to support ACPI 5.0 in order to be able to pass the FixedDMA entries to the kernel. There are also no ACPI methods defined yet to do D0->D3->D0 transitions for actually entering/exiting S0ix states. This is hard to test right now because our kernel does not support any of these devices in ACPI mode. I was able to build and test the upstream bleeding-edge branch of the linux-pm git tree. With that tree I was able to enumerate and load the driver for the DesignWare I2C driver and attempt to probe the I2C bus -- although there are no devices attatched. I am also able to see the resources from ACPI in /proc/iomem get reserved properly in the kernel. Change-Id: Ie311addd6a25f3b7edf3388fe68c1cd691a0a500 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2971 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-04-01wtm2: Enable SerialIO devices in ACPI modeDuncan Laurie
This enables all of the SerialIO devices and sets the flag to put them in ACPI mode. Change-Id: I7436c47d26028e95bbefafc320854c7cc34a4d44 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2972 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-04-01lynxpoint: Fix LP clock gating setup for LPCDuncan Laurie
This bit offset is incorrect and should only be set based on another bit in a different register. Change-Id: I6037534236e3a4a5d15e15011ed9b5040b435eaf Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2973 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-04-01Minor Kconfig help text fixStefan Tauner
I did not check what was once after the 'and'. Change-Id: I9f3f725bec281a94abdb2eeb692a96fecdebcc0c Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at> Reviewed-on: http://review.coreboot.org/2999 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01chromeos: honor MOCK_TPM=1Aaron Durbin
The TPM code wasn't previously honoring MOCK_TPM=1. Because of this, boards with TPMs that didn't handle S3 resume properly would cause a hard reset. Allow one to build with MOCK_TPM=1 on the command line so that S3 can still work. Change-Id: I9adf06647de285c0b0a3203d8897be90d7783a1e Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2976 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-04-01lynxpoint: fix enable_pm1() functionAaron Durbin
The new enable_pm1() function was doing 2 things wrong: 1. It was doing a RMW of the pm1 register. This means we were keeping around the enables from the OS during S3 resume. This is bad in the face of the RTC alarm waking us up because it would cause an infinite stream of SMIs. 2. The register size of PM1_EN is 16-bits. However, the previous implementation was accessing it as a 32-bit register. The PM1 enables should only be set to what we expect to handle in the firmware before the OS changes to ACPI mode. Change-Id: Ib1d3caf6c84a1670d9456ed159420c6cb64f555e Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2978 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-04-01PDCurses: pdcscrn.c: Use `#ifdef` instead of `#if CONFIG_SPEAKER`Paul Menzel
Building libpayload with the PDCurses backend the following warning is shown. /src/coreboot/payloads/libpayload(master) $ make clean /src/coreboot/payloads/libpayload(master) $ make […] CC curses/pdcurses-backend/pdcscrn.libcurses.o curses/pdcurses-backend/pdcscrn.c: In function 'PDC_scr_open': curses/pdcurses-backend/pdcscrn.c:75:5: warning: "CONFIG_SPEAKER" is not defined [-Wundef] […] The GCC documentation states [1] In some contexts this shortcut is undesirable. The -Wundef option causes GCC to warn whenever it encounters an identifier which is not a macro in an ‘#if’. and therefore use `#ifdef` [2] to silence this warning. No functional change is done, as `CONFIG_SPEAKER` is assigned the value `Y` when defined. There was some discussion going on the list [3], but my points in there turned out to be incorrect. [1] http://gcc.gnu.org/onlinedocs/cpp/If.html [2] http://gcc.gnu.org/onlinedocs/cpp/Ifdef.html [3] http://www.coreboot.org/pipermail/coreboot/2013-March/075561.html Change-Id: I8e9c9b5d01985b21ad05018986d614cf9bf2b439 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2934 Reviewed-by: Nico Huber <nico.huber@secunet.com> Tested-by: build bot (Jenkins)
2013-04-01lynxpoint: split clearing and enabling of smmAaron Durbin
Previously southbridge_smm_init() was provided that did both the clearing of the SMM state and enabling SMIs. This is troublesome in how haswell machines bring up the APs. The BSP enters SMM once to determine if parallel SMM relocation is possible. If it is possible the BSP releases the APs to do SMM relocation. Normally, after the APs complete the SMM relocation, the BSP would then re-enter the relocation handler to relocate its own SMM space. However, because SMIs were previously enabled it is possible for an SMI event to occur before the APs are complete or have entered the relocation handler. This is bad because the BSP will turn off parallel SMM save state. Additionally, this is a problem because the relocation handler is not written to handle regular SMIs which can cause an SMI storm which effectively looks like a hung machine. Correct these issues by turning on SMIs after all the SMM relocation has occurred. Change-Id: Id4f07553b110b9664d51d2e670a14e6617591500 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2977 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-04-01inteltool: Allow to override Makefile variablesPaul Menzel
Allow to override the variables `CC`, `INSTALL`, `PREFIX`, `CFLAGS` and `LDFLAGS`. Though append `-lpci -lz` to `LDFLAGS`. This way for example a different compiler can easily be used. CC=clang make As a side note, Clang in contrast to GCC does *not* issue the following warnings. $ clang --version Debian clang version 3.2-1~exp6 (tags/RELEASE_32/final) (based on LLVM 3.2) Target: i386-pc-linux-gnu Thread model: posix $ gcc --version gcc-4.7.real (Debian 4.7.2-15) 4.7.2 Copyright (C) 2012 Free Software Foundation, Inc. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. $ make […] amb.c: In function ‘amb_read_config32’: amb.c:31:23: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] amb.c:31:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] amb.c: In function ‘amb_read_config16’: amb.c:45:23: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] amb.c:45:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] amb.c: In function ‘amb_read_config8’: amb.c:60:22: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] amb.c:60:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] […] These are only shown under 32-bit and not 64-bit $ uname -m i686 and are going to be fixed in a separate patch. Change-Id: Id75dea081ecb35390f283520a7e5dce520f4c98d Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2996 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01inteltool: Add Cougar/Panther Point GPIO defaultsNico Huber
This adds default values for the GPIO setup on Intel's Cougar Point and Panther Point platform controller hubs (PCH). Values are taken from [1] and [2], respectively. I've tested this with an H77 PCH. See below for the output. [1] Intel 6 Series Chipset and Intel C200 Series Chipset - Datasheet Document-Number: 324645-006 [2] Intel 7 Series / C216 Chipset Family Platform Controller Hub (PCH) - Datasheet Document-Number: 326776-003 $ ./inteltool -G CPU: Processor Type: 0, Family 6, Model 3a, Stepping 9 Northbridge: 8086:0150 (unknown) Southbridge: 8086:1e4a (H77) ========== GPIO DIFFS =========== GPIOBASE = 0x0500 (IO) gpiobase+0x0000: 0xb96ba1fb (GPIO_USE_SEL) gpiobase+0x0000: 0xb96ba1ff (GPIO_USE_SEL) DEFAULT gpiobase+0x0000: 0x00000004 (GPIO_USE_SEL) DIFF gpiobase+0x0004: 0x06ff6efb (GP_IO_SEL) gpiobase+0x0004: 0xeeff6eff (GP_IO_SEL) DEFAULT gpiobase+0x0004: 0xe8000004 (GP_IO_SEL) DIFF gpiobase+0x000c: 0xe1f17f7e (GP_LVL) gpiobase+0x000c: 0x02fe0100 (GP_LVL) DEFAULT gpiobase+0x000c: 0xe30f7e7e (GP_LVL) DIFF gpiobase+0x002c: 0x00002000 (GPI_INV) gpiobase+0x002c: 0x00000000 (GPI_INV) DEFAULT gpiobase+0x002c: 0x00002000 (GPI_INV) DIFF gpiobase+0x0030: 0x0aff70ff (GPIO_USE_SEL2) gpiobase+0x0030: 0x020300ff (GPIO_USE_SEL2) DEFAULT gpiobase+0x0030: 0x08fc7000 (GPIO_USE_SEL2) DIFF gpiobase+0x0034: 0x15038ff2 (GP_IO_SEL2) gpiobase+0x0034: 0x1f57fff4 (GP_IO_SEL2) DEFAULT gpiobase+0x0034: 0x0a547006 (GP_IO_SEL2) DIFF gpiobase+0x0038: 0xb65e7f4f (GP_LVL2) gpiobase+0x0038: 0xa4aa0007 (GP_LVL2) DEFAULT gpiobase+0x0038: 0x12f47f48 (GP_LVL2) DIFF gpiobase+0x0040: 0x000001f3 (GPIO_USE_SEL3) gpiobase+0x0040: 0x00000130 (GPIO_USE_SEL3) DEFAULT gpiobase+0x0040: 0x000000c3 (GPIO_USE_SEL3) DIFF gpiobase+0x0044: 0x00000ef3 (GPIO_SEL3) gpiobase+0x0044: 0x00000ff0 (GPIO_SEL3) DEFAULT gpiobase+0x0044: 0x00000103 (GPIO_SEL3) DIFF gpiobase+0x0048: 0x00000dfc (GPIO_LVL3) gpiobase+0x0048: 0x000000c0 (GPIO_LVL3) DEFAULT gpiobase+0x0048: 0x00000d3c (GPIO_LVL3) DIFF gpiobase+0x0060: 0x00000000 (GP_RST_SEL1) gpiobase+0x0060: 0x01000000 (GP_RST_SEL1) DEFAULT gpiobase+0x0060: 0x01000000 (GP_RST_SEL1) DIFF $ ./inteltool -gG CPU: Processor Type: 0, Family 6, Model 3a, Stepping 9 Northbridge: 8086:0150 (unknown) Southbridge: 8086:1e4a (H77) ============= GPIOS ============= GPIOBASE = 0x0500 (IO) gpiobase+0x0000: 0xb96ba1fb (GPIO_USE_SEL) gpiobase+0x0000: 0xb96ba1ff (GPIO_USE_SEL) DEFAULT gpiobase+0x0000: 0x00000004 (GPIO_USE_SEL) DIFF gpiobase+0x0004: 0x06ff6efb (GP_IO_SEL) gpiobase+0x0004: 0xeeff6eff (GP_IO_SEL) DEFAULT gpiobase+0x0004: 0xe8000004 (GP_IO_SEL) DIFF gpiobase+0x0008: 0x00000000 (RESERVED) gpiobase+0x000c: 0xe1f17f7e (GP_LVL) gpiobase+0x000c: 0x02fe0100 (GP_LVL) DEFAULT gpiobase+0x000c: 0xe30f7e7e (GP_LVL) DIFF gpiobase+0x0010: 0x00000000 (RESERVED) gpiobase+0x0014: 0x00000000 (RESERVED) gpiobase+0x0018: 0x00040000 (GPO_BLINK) gpiobase+0x001c: 0x00000000 (GP_SER_BLINK) gpiobase+0x0020: 0x00080000 (GP_SB_CMDSTS) gpiobase+0x0024: 0x00000000 (GP_SB_DATA) gpiobase+0x0028: 0x0000 (GPI_NMI_EN) gpiobase+0x002a: 0x0000 (GPI_NMI_STS) gpiobase+0x002c: 0x00002000 (GPI_INV) gpiobase+0x002c: 0x00000000 (GPI_INV) DEFAULT gpiobase+0x002c: 0x00002000 (GPI_INV) DIFF gpiobase+0x0030: 0x0aff70ff (GPIO_USE_SEL2) gpiobase+0x0030: 0x020300ff (GPIO_USE_SEL2) DEFAULT gpiobase+0x0030: 0x08fc7000 (GPIO_USE_SEL2) DIFF gpiobase+0x0034: 0x15038ff2 (GP_IO_SEL2) gpiobase+0x0034: 0x1f57fff4 (GP_IO_SEL2) DEFAULT gpiobase+0x0034: 0x0a547006 (GP_IO_SEL2) DIFF gpiobase+0x0038: 0xb65e7f4f (GP_LVL2) gpiobase+0x0038: 0xa4aa0007 (GP_LVL2) DEFAULT gpiobase+0x0038: 0x12f47f48 (GP_LVL2) DIFF gpiobase+0x003c: 0x00000000 (RESERVED) gpiobase+0x0040: 0x000001f3 (GPIO_USE_SEL3) gpiobase+0x0040: 0x00000130 (GPIO_USE_SEL3) DEFAULT gpiobase+0x0040: 0x000000c3 (GPIO_USE_SEL3) DIFF gpiobase+0x0044: 0x00000ef3 (GPIO_SEL3) gpiobase+0x0044: 0x00000ff0 (GPIO_SEL3) DEFAULT gpiobase+0x0044: 0x00000103 (GPIO_SEL3) DIFF gpiobase+0x0048: 0x00000dfc (GPIO_LVL3) gpiobase+0x0048: 0x000000c0 (GPIO_LVL3) DEFAULT gpiobase+0x0048: 0x00000d3c (GPIO_LVL3) DIFF gpiobase+0x004c: 0x00000000 (RESERVED) gpiobase+0x0050: 0x00000000 (RESERVED) gpiobase+0x0054: 0x00000000 (RESERVED) gpiobase+0x0058: 0x00000000 (RESERVED) gpiobase+0x005c: 0x00000000 (RESERVED) gpiobase+0x0060: 0x00000000 (GP_RST_SEL1) gpiobase+0x0060: 0x01000000 (GP_RST_SEL1) DEFAULT gpiobase+0x0060: 0x01000000 (GP_RST_SEL1) DIFF gpiobase+0x0064: 0x00000000 (GP_RST_SEL2) gpiobase+0x0068: 0x00000000 (GP_RST_SEL3) gpiobase+0x006c: 0x00000000 (RESERVED) gpiobase+0x0070: 0x00000000 (RESERVED) gpiobase+0x0074: 0x00000000 (RESERVED) gpiobase+0x0078: 0x00000000 (RESERVED) gpiobase+0x007c: 0x00000000 (RESERVED) Change-Id: If99cf8d5c93e34ad28f52080fff64e01c220eb27 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/3001 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01inteltool: Add option to show differences in GPIO setupNico Huber
This adds an option -G, --gpio-diffs to inteltool, which shows GPIO settings that differ from platform defaults. For differing registers, the current, the default, and an xor of the default and the current value is printed. A follow-up commit will add defaults for the Cougar/Panther Point platform controller hubs. If you specify both, -g and -G on the command line, all GPIO registers will be printed interleaved with the diff. Here's a preview: $ ./inteltool -G CPU: Processor Type: 0, Family 6, Model 3a, Stepping 9 Northbridge: 8086:0150 (unknown) Southbridge: 8086:1e4a (H77) ========== GPIO DIFFS =========== GPIOBASE = 0x0500 (IO) gpiobase+0x0000: 0xb96ba1fb (GPIO_USE_SEL) gpiobase+0x0000: 0xb96ba1ff (GPIO_USE_SEL) DEFAULT gpiobase+0x0000: 0x00000004 (GPIO_USE_SEL) DIFF gpiobase+0x0004: 0x06ff6efb (GP_IO_SEL) gpiobase+0x0004: 0xeeff6eff (GP_IO_SEL) DEFAULT gpiobase+0x0004: 0xe8000004 (GP_IO_SEL) DIFF gpiobase+0x000c: 0xe1f17f7e (GP_LVL) gpiobase+0x000c: 0x02fe0100 (GP_LVL) DEFAULT gpiobase+0x000c: 0xe30f7e7e (GP_LVL) DIFF gpiobase+0x002c: 0x00002000 (GPI_INV) gpiobase+0x002c: 0x00000000 (GPI_INV) DEFAULT gpiobase+0x002c: 0x00002000 (GPI_INV) DIFF gpiobase+0x0030: 0x0aff70ff (GPIO_USE_SEL2) gpiobase+0x0030: 0x020300ff (GPIO_USE_SEL2) DEFAULT gpiobase+0x0030: 0x08fc7000 (GPIO_USE_SEL2) DIFF gpiobase+0x0034: 0x15038ff2 (GP_IO_SEL2) gpiobase+0x0034: 0x1f57fff4 (GP_IO_SEL2) DEFAULT gpiobase+0x0034: 0x0a547006 (GP_IO_SEL2) DIFF gpiobase+0x0038: 0xb65e7f4f (GP_LVL2) gpiobase+0x0038: 0xa4aa0007 (GP_LVL2) DEFAULT gpiobase+0x0038: 0x12f47f48 (GP_LVL2) DIFF gpiobase+0x0040: 0x000001f3 (GPIO_USE_SEL3) gpiobase+0x0040: 0x00000130 (GPIO_USE_SEL3) DEFAULT gpiobase+0x0040: 0x000000c3 (GPIO_USE_SEL3) DIFF gpiobase+0x0044: 0x00000ef3 (GPIO_SEL3) gpiobase+0x0044: 0x00000ff0 (GPIO_SEL3) DEFAULT gpiobase+0x0044: 0x00000103 (GPIO_SEL3) DIFF gpiobase+0x0048: 0x00000dfc (GPIO_LVL3) gpiobase+0x0048: 0x000000c0 (GPIO_LVL3) DEFAULT gpiobase+0x0048: 0x00000d3c (GPIO_LVL3) DIFF gpiobase+0x0060: 0x00000000 (GP_RST_SEL1) gpiobase+0x0060: 0x01000000 (GP_RST_SEL1) DEFAULT gpiobase+0x0060: 0x01000000 (GP_RST_SEL1) DIFF $ ./inteltool -gG CPU: Processor Type: 0, Family 6, Model 3a, Stepping 9 Northbridge: 8086:0150 (unknown) Southbridge: 8086:1e4a (H77) ============= GPIOS ============= GPIOBASE = 0x0500 (IO) gpiobase+0x0000: 0xb96ba1fb (GPIO_USE_SEL) gpiobase+0x0000: 0xb96ba1ff (GPIO_USE_SEL) DEFAULT gpiobase+0x0000: 0x00000004 (GPIO_USE_SEL) DIFF gpiobase+0x0004: 0x06ff6efb (GP_IO_SEL) gpiobase+0x0004: 0xeeff6eff (GP_IO_SEL) DEFAULT gpiobase+0x0004: 0xe8000004 (GP_IO_SEL) DIFF gpiobase+0x0008: 0x00000000 (RESERVED) gpiobase+0x000c: 0xe1f17f7e (GP_LVL) gpiobase+0x000c: 0x02fe0100 (GP_LVL) DEFAULT gpiobase+0x000c: 0xe30f7e7e (GP_LVL) DIFF gpiobase+0x0010: 0x00000000 (RESERVED) gpiobase+0x0014: 0x00000000 (RESERVED) gpiobase+0x0018: 0x00040000 (GPO_BLINK) gpiobase+0x001c: 0x00000000 (GP_SER_BLINK) gpiobase+0x0020: 0x00080000 (GP_SB_CMDSTS) gpiobase+0x0024: 0x00000000 (GP_SB_DATA) gpiobase+0x0028: 0x0000 (GPI_NMI_EN) gpiobase+0x002a: 0x0000 (GPI_NMI_STS) gpiobase+0x002c: 0x00002000 (GPI_INV) gpiobase+0x002c: 0x00000000 (GPI_INV) DEFAULT gpiobase+0x002c: 0x00002000 (GPI_INV) DIFF gpiobase+0x0030: 0x0aff70ff (GPIO_USE_SEL2) gpiobase+0x0030: 0x020300ff (GPIO_USE_SEL2) DEFAULT gpiobase+0x0030: 0x08fc7000 (GPIO_USE_SEL2) DIFF gpiobase+0x0034: 0x15038ff2 (GP_IO_SEL2) gpiobase+0x0034: 0x1f57fff4 (GP_IO_SEL2) DEFAULT gpiobase+0x0034: 0x0a547006 (GP_IO_SEL2) DIFF gpiobase+0x0038: 0xb65e7f4f (GP_LVL2) gpiobase+0x0038: 0xa4aa0007 (GP_LVL2) DEFAULT gpiobase+0x0038: 0x12f47f48 (GP_LVL2) DIFF gpiobase+0x003c: 0x00000000 (RESERVED) gpiobase+0x0040: 0x000001f3 (GPIO_USE_SEL3) gpiobase+0x0040: 0x00000130 (GPIO_USE_SEL3) DEFAULT gpiobase+0x0040: 0x000000c3 (GPIO_USE_SEL3) DIFF gpiobase+0x0044: 0x00000ef3 (GPIO_SEL3) gpiobase+0x0044: 0x00000ff0 (GPIO_SEL3) DEFAULT gpiobase+0x0044: 0x00000103 (GPIO_SEL3) DIFF gpiobase+0x0048: 0x00000dfc (GPIO_LVL3) gpiobase+0x0048: 0x000000c0 (GPIO_LVL3) DEFAULT gpiobase+0x0048: 0x00000d3c (GPIO_LVL3) DIFF gpiobase+0x004c: 0x00000000 (RESERVED) gpiobase+0x0050: 0x00000000 (RESERVED) gpiobase+0x0054: 0x00000000 (RESERVED) gpiobase+0x0058: 0x00000000 (RESERVED) gpiobase+0x005c: 0x00000000 (RESERVED) gpiobase+0x0060: 0x00000000 (GP_RST_SEL1) gpiobase+0x0060: 0x01000000 (GP_RST_SEL1) DEFAULT gpiobase+0x0060: 0x01000000 (GP_RST_SEL1) DIFF gpiobase+0x0064: 0x00000000 (GP_RST_SEL2) gpiobase+0x0068: 0x00000000 (GP_RST_SEL3) gpiobase+0x006c: 0x00000000 (RESERVED) gpiobase+0x0070: 0x00000000 (RESERVED) gpiobase+0x0074: 0x00000000 (RESERVED) gpiobase+0x0078: 0x00000000 (RESERVED) gpiobase+0x007c: 0x00000000 (RESERVED) Change-Id: Ic77474c4bc0871e95103ddecd9f6a9406c8f016d Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/3000 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01Winbond W83627HF: Rename and move ASL snippet to `acpi/superio.asl`Paul Menzel
Put the ASL snippet for inclusion in the DSDT under the `acpi/` folder as it is done for the other Super I/O devices. $ find src/superio/ -name *asl src/superio/ite/it8772f/acpi/superio.asl src/superio/smsc/mec1308/acpi/superio.asl src/superio/smsc/sio1007/acpi/superio.asl src/superio/winbond/w83627hf/devtree.asl As there are no users of this file yet, no other adaptations need to be made. Change-Id: Id10cd8897592b780c9fd3bd6b45ada4cf1fcf33e Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2937 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01ASRock E350M1: mptable.c: Remove unused variable `dev`Paul Menzel
When building the ASRock E350M1, the following warning is shown. $ make # on Jenkins (build server) […] CC mainboard/asrock/e350m1/mptable.ramstage.o src/mainboard/asrock/e350m1/mptable.c:64:12: warning: unused variable 'dev' [-Wunused-variable] […] Removing the variable `dev` addresses the warning. The same change was done in the following commit for the AMD Persimmon board. commit d7a696d0f229abccc95ff411f28d91b9b796ab74 Author: efdesign98 <efdesign98@gmail.com> Date: Thu Sep 15 15:24:26 2011 -0600 Persimmon updates for AMD F14 rev C0 Reviewed-on: http://review.coreboot.org/137 Change-Id: I83f4630cb6ab1e4c95d04b4e8423850ed1858e45 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2965 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01ASRock E350M1: mptable.c: Include `cpu/amd/amdfam14.h` for `get_bus_conf`Paul Menzel
When building the ASRock E350M1, the following warning is shown. $ make # on Jenkins (build server) […] CC mainboard/asrock/e350m1/mptable.ramstage.o src/mainboard/asrock/e350m1/mptable.c: In function 'smp_write_config_table': src/mainboard/asrock/e350m1/mptable.c:58:3: warning: implicit declaration of function 'get_bus_conf' [-Wimplicit-function-declaration] […] Including the header file `cpu/amd/amdfam14.h` declaring the function addresses this warning. The same change was done in the following commit for the AMD Persimmon board. commit d7a696d0f229abccc95ff411f28d91b9b796ab74 Author: efdesign98 <efdesign98@gmail.com> Date: Thu Sep 15 15:24:26 2011 -0600 Persimmon updates for AMD F14 rev C0 Reviewed-on: http://review.coreboot.org/137 Change-Id: I7912571fa57f6512b10fc9b5845427fcb6eb50c0 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2966 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01ASRock E350M1: mainboard.c: Include `cimx_util.h` for `pm_iowrite`Paul Menzel
When building the ASRock E350M1, the following warning is shown. $ make # on Jenkins (build server) […] CC mainboard/asrock/e350m1/mainboard.ramstage.o src/mainboard/asrock/e350m1/mainboard.c: In function 'mainboard_enable': src/mainboard/asrock/e350m1/mainboard.c:63:2: warning: implicit declaration of function 'pm_iowrite' [-Wimplicit-function-declaration] […] This warning was introduced by moving the initialization of the ASF registers using `pm_iowrite` to `mainboard.c` in commit db6c5bfd8bdef4489e7fec533cb2ca8ae6c24cf3 Author: Jens Rottmann <JRottmann@LiPPERTembedded.de> Date: Thu Mar 21 22:21:28 2013 +0100 Asrock E350M1: Use SPD read code from F14 wrapper Reviewed-on: http://review.coreboot.org/2875 and is fixed by including `southbridge/amd/cimx/cimx_util.h` declaring `pm_iowrite`. Note, that the other AMD SB800 based boards seem to use the header file `southbridge/amd/sb800/sb800.h`, so no warning is shown for those. But since the CIMx SB800 code is used, the routines from the CIMx directory are more appropriate to declare these functions. So delete the commented out include line for this header too. Change-Id: I179aad5157c5a91294339a3e7b6c4c1715c6f099 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2957 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01inteltool: Support PM registers on Cougar/Panther PointNico Huber
This adds the power management register definitions for Intel's Cougar Point and Panther Point platform controller hubs (PCH). The definitions are actually a subset of the older ICH10R registers: I've added just those that are mentioned in the public specifications in [1] and [2]. I've tested dumping with an H77 PCH. NM70 is missing in [1]. Therefore, I didn't add it here. [1] Intel 6 Series Chipset and Intel C200 Series Chipset - Datasheet Document-Number: 324645-006 [2] Intel 7 Series / C216 Chipset Family Platform Controller Hub (PCH) - Datasheet Document-Number: 326776-003 Change-Id: Ia6945fe96cd96b568ed5191e91dbba5556e1ee95 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/2985 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01wtm2: select write-combining memory for graphicsAaron Durbin
Auto-select marking the graphics memory as write-combining. Change-Id: Icf61c5cbd129a97a106f0aaeca4e010d4799b4b8 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2981 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01link: select write-combining memory for graphicsAaron Durbin
Auto-select marking the graphics memory as write-combining. Change-Id: I0b913f0b318bf57275643d3cfb5bc54ca8a005f5 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2982 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01pci: don't load vga option rom before S3 checkAaron Durbin
The pci device code was probing and loading the option rom before it did the S3 resume check for VGA option roms. Instead move this check before probing and loading so that we don't unnecessarily do work. Change-Id: If2e62d0c0e4b34b4f1bcd56ebcb9d3f54c6d0d24 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2979 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Tested-by: build bot (Jenkins)
2013-04-01console: Make use of CONFIG_USE_OPTION_TABLEChristian Gmeiner
It makes much more sense to use CONFIG_USE_OPTION_TABLE instead of CONFIG_HAVE_CMOS_DEFAULT. As we want to read the used debug_level from our CMOS. This change makes it possible to change log_debug via nvramtool and make use of the new value after a reboot/poweroff. CONFIG_HAVE_CMOS_DEFAULT does have an other meaning Change-Id: I438dd01a2b4171dba2b73f2001511c71f4317725 Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-on: http://review.coreboot.org/2381 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-04-01AMD hudson & SB800 - Fix issues with mawkMartin Roth
When calculating the offsets of the various binary blobs within the coreboot.rom file, we noticed that using mawk as the awk tool instead of using gawk led to build issues. This was finally traced to the maximum value of the unsigned long variables within mawk - 0x7fff_ffff. Because we were doing calculations on values up in the 0xffxxxxxx range, these numbers would either be turned into floating point values and printed using scientific notation, or truncated at 0x7fff_ffff. To fix this, we print the values out as floating point, with no decimal digits. This works in gawk, mawk, and original-awk and as the testing below show, seems to be the best way to do this. printf %u 0xFFFFFFFF | awk '{printf("%.0f %u %d", $1 , $1 , $1 )}' mawk: 4294967295 2147483647 2147483647 original-awk: 4294967295 2147483648 4294967295 gawk: 4294967295 4294967295 4294967295 The issue of %d not matching gawk and original-awk has been reported to ubuntu. In the future, I'd recommend that whenever awk is used, a format is specified. It doesn't seem that we can count on the representation being the same between the different versions. Change-Id: I7b6b821c8ab13ad11f72e674ac726a98e8678710 Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/2628 Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-04-01lynxpoint: Rework ACPI NVS to add new SerialIO variablesDuncan Laurie
This reclaims space in ACPI NVS by removing unused fields and adds new fields for SerialIO BARs which will be used to communicate the allocated resources to ACPI. Change-Id: I002bf396cf7b495bc5b7e54b741527e507aff716 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2969 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-30wtm1/wtm2/baskingridge: Enable TPM ACPI deviceDuncan Laurie
This enables the TPM device in ACPI tables so the OS is able to probe for the TPM without needing it be force loaded. Change-Id: I21e660ac1c12e3e1341cf266cf8f0bf03763df5a Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2968 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-30armv7: import updated cache/MMU stuff from corebootDavid Hendricks
This imports the newest cache and MMU code from coreboot. This time it's so new that it hasn't even been checked in to coreboot. However, this version at least allows DMA to work properly for the MSHC driver. So even if we rebase a few more times, this version is at least a step in the right direction. Note: This omits the stuff that sets up dcache policy since libpayload should not need to worry about that and it depends on cbmem stuff. Change-Id: Idd42b083e8019634aaaa44d5bf5b51db6c3912f5 Signed-off-by: David Hendricks <dhendrix@google.com> Reviewed-on: http://review.coreboot.org/2975 Reviewed-by: David Hendricks <dhendrix@chromium.org> Tested-by: build bot (Jenkins)
2013-03-30armv7: import new cache maintenance API from corebootDavid Hendricks
This imports the new cache maintenance API from coreboot at commit bba8090. This is a BSD-licensed implementation which exposes cache maintenance opertaions necessary for payloads for things such as DMA transfers. Change-Id: I554676db89517bebc6edae4f7ab7e5882e6f986d Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2974 Tested-by: build bot (Jenkins)
2013-03-30x86: Drop BOARD_HAS_FADTKyösti Mälkki
There is a wildcard rule to include mainboard/fadt.c. Change-Id: I7f59d6b241c683b62c2c41c5795e45184882635e Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/2940 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-30inteltool: Add Cougar/Panther Point IDs to rootcmplx.cNico Huber
This adds the PCI IDs of Intel's Cougar Point and Panther Point platform controller hubs (PCH) to the dumping of the root complex configuration under the root complex base address (RCBA). Those PCHs are handled exactly as the older ICHs which can be seen in [1] and [2]. I've tested dumping with an H77 PCH. NM70 is missing in [1]. Therefore, I didn't add it here. [1] Intel 6 Series Chipset and Intel C200 Series Chipset - Datasheet Document-Number: 324645-006 [2] Intel 7 Series / C216 Chipset Family Platform Controller Hub (PCH) - Datasheet Document-Number: 326776-003 Change-Id: I2296caae57e614171300362d41715deecec77762 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/2986 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-30AMD Hudson boards: Use `hudson.h` for `pm_ioread` and delete `pmio.h`Paul Menzel
Unfortunately, an unneeded mainboard specific `pmio.h` was created when merging the AMD Parmer and Thatcher ports. Rudolf used the header from a more generic location southbridge/amd/agesa/hudson/hudson.h doing the the ASUS F2A85-M port, but did not delete the `pmio.h` now unused `pmio.h` header file. So adapt AMD Parmer and Thatcher to use the Hudson one as done for the ASUS F2A85-M and delete the now unused mainboard specific header file `pmio.h` to avoid duplication. Change-Id: I961cd145ebc3b83e31c638ac453ac95ee19c18db Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2958 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-30ASRock E350M1: irq_tables.c: Include `cpu/amd/amdfam14.h` for `get_bus_conf`Paul Menzel
When building the ASRock E350M1, the following warning is shown. $ make # on Jenkins (build server) […] CC mainboard/asrock/e350m1/irq_tables.ramstage.o src/mainboard/asrock/e350m1/irq_tables.c: In function 'write_pirq_routing_table': src/mainboard/asrock/e350m1/irq_tables.c:64:2: warning: implicit declaration of function 'get_bus_conf' [-Wimplicit-function-declaration] […] Including the header file `cpu/amd/amdfam14.h` declaring the function addresses this warning. The same change was done in the following commit for the AMD Persimmon board. commit d7a696d0f229abccc95ff411f28d91b9b796ab74 Author: efdesign98 <efdesign98@gmail.com> Date: Thu Sep 15 15:24:26 2011 -0600 Persimmon updates for AMD F14 rev C0 Reviewed-on: http://review.coreboot.org/137 Change-Id: I40b5735feb7116961ca0c4d6940ec55cdf42d3c6 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2956 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-30ASRock E350M1: get_bus_conf.c: Include `agesawrapper.h` for ↵Paul Menzel
`agesawrapper_amdinitlate` When building the ASRock E350M1, the following warning is shown. $ make # on Jenkins (build server) […] CC mainboard/asrock/e350m1/get_bus_conf.ramstage.o src/mainboard/asrock/e350m1/get_bus_conf.c: In function 'get_bus_conf': src/mainboard/asrock/e350m1/get_bus_conf.c:82:3: warning: implicit declaration of function 'agesawrapper_amdinitlate' [-Wimplicit-function-declaration] […] Including the header file `agesawrapper.h` declaring the function `agesawrapper_amdinitlate` fixes this warning. All AMD Family 14 based boards already include that header file. For example for the board AMD Persimmon the following patch fixed this warning. commit d7a696d0f229abccc95ff411f28d91b9b796ab74 Author: efdesign98 <efdesign98@gmail.com> Date: Thu Sep 15 15:24:26 2011 -0600 Persimmon updates for AMD F14 rev C0 Reviewed-on: http://review.coreboot.org/137 Change-Id: I695420b7071e07cb7d4667b2479b9a26ea13723d Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2955 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-30ASRock E350M1: PlatformGnbPcie.c: Do not return anything for void return typePaul Menzel
When building the ASRock E350M1, the following warning is shown. $ make # on Jenkins (build server) […] CC mainboard/asrock/e350m1/PlatformGnbPcie.romstage.o CC mainboard/asrock/e350m1/agesawrapper.romstage.o CC mainboard/asrock/e350m1/buildOpts.romstage.o src/mainboard/asrock/e350m1/PlatformGnbPcie.c: In function 'OemCustomizeInitEarly': src/mainboard/asrock/e350m1/PlatformGnbPcie.c:131:5: warning: 'return' with a value, in function returning void [enabled by default] […] The function signature is (the return type might not be part of this though [1]), VOID OemCustomizeInitEarly ( IN OUT AMD_EARLY_PARAMS *InitEarly ) so do not return anything. All other AMD Family 14 boards already have the correct code. For example following commit fixed this for AMD Persimmon. commit d7a696d0f229abccc95ff411f28d91b9b796ab74 Author: efdesign98 <efdesign98@gmail.com> Date: Thu Sep 15 15:24:26 2011 -0600 Persimmon updates for AMD F14 rev C0 Reviewed-on: http://review.coreboot.org/137 [1] http://cboard.cprogramming.com/cplusplus-programming/117286-what-exactly-function-signature.html Change-Id: Ie60246bd9bb8452efd096e6838d8610f6364a6aa Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2954 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-30armv7: change some unsigned ints to uint32_tDavid Hendricks
Use register-sized types in case the inline assembler doesn't do so automatically. Change-Id: I3202ba972ef2548323fe557f45dc4b0b1cf6c818 Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2983 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Gabe Black <gabe.black@gmail.com> Tested-by: build bot (Jenkins)
2013-03-29armv7: remove loop from dcache_mmu_disable()David Hendricks
dcache_mmu_disable() no longer needs to have its own iterative loop to select each cache level of cache since dcache_clean_invalidate_all() does that now. Change-Id: I5ca273f98943981b943c1c1622f4574d7133fb50 Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2967 Reviewed-by: Gabe Black <gabe.black@gmail.com> Tested-by: build bot (Jenkins)
2013-03-29snow: explicitly configure L2 cacheDavid Hendricks
This adds a call to explicitly configure L2 cache (though defaults should be set correctly). Change-Id: I120e29c986918c2904a0332e46fcf9f1c5380d85 Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2950 Reviewed-by: Gabe Black <gabe.black@gmail.com> Tested-by: build bot (Jenkins)
2013-03-29exynos5250: Add function for configuring L2 cacheDavid Hendricks
This adds a new function to configure L2 cache for the exynos5250 and deprecates the old function. Change-Id: I9562f3301aa1e2911dae3856ab57bb6beec2e224 Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2949 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Gabe Black <gabe.black@gmail.com> Tested-by: build bot (Jenkins)
2013-03-29AMD CIMx SB800: Update Kconfig help texts to new SATA mode defaultPaul Menzel
In the following commit commit ee5c111755ac4acc6dfb6e10a4e271211e149a39 Author: Paul Menzel <paulepanter@users.sourceforge.net> Date: Tue Mar 12 12:41:40 2013 +0100 AMD CIMx SB800: Enable AHCI mode for SATA controller by default Reviewed-on: http://review.coreboot.org/2661 I forgot to update the help texts to the new SATA mode default. Do so now. Additionally note that help texts for `choice` do not seem to be shown. Change-Id: I17f401633a2136efca2b21a621482e0724ff9f04 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2936 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-29superiotool: Allow to override Makefile variables `CC`, `INSTALL` and `PREFIX`Paul Menzel
This way for example a different compiler can easily be used. CC=clang make Change-Id: I50b83554fd4826d00d87e60a30eb1f6a88834397 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2935 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-29armv7: update sync barrier usage in dcache_op_set_way()David Hendricks
This moves the dsb() before the loop to sync any outstanding memory accesses, and adds an isb() after the loop to ensure all outstanding instructions are completed. Change-Id: I1a11b39f104ae780370cfd2db3badcf4e91dc017 Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2929 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29wtm2: auto-select CACHE_ROMAaron Durbin
The WTM2 board has a fairly static configuration. As such it's been tested to properly handle CACHE_ROM given the number of MTRRs the boards' CPUs supports. Change-Id: Ic67cd1eebce580003dc6b6655cac2b2a92dd1b5f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2964 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29AMD Inagua: Kconfig: Remove `WARNINGS_ARE_ERRORS` to treat warnings as errorsPaul Menzel
Now that the AMD Inagua builds without any warnigs, remove the config option `WARNINGS_ARE_ERRORS` set to no by default from the file `Kconfig` so warnings are treated as errors to prevent code from being added in the future introducing warnings. Change-Id: I0b58bd74b06dc54d180b16d6a207354b5fea0d0f Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2953 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29AMD Inagua: broadcom.c: Add missing prototype for `broadcom_init()`Paul Menzel
Building the AMD Inagua board, the following warning is thrown. CC mainboard/amd/inagua/get_bus_conf.ramstage.o src/mainboard/amd/inagua/broadcom.c:319:6: warning: no previous prototype for 'broadcom_init' [-Wmissing-prototypes] This warning was introduced by commit 3926b4c5. commit 3926b4c520e74da9dc22e3d136a8a178483e0d25 Author: Jens Rottmann <JRottmann@LiPPERTembedded.de> Date: Fri Mar 1 19:41:41 2013 +0100 AMD Inagua: add GEC firmware, document Broadcom BCM57xx Selfboot Patch format Reviewed-on: http://review.coreboot.org/2831 Adding the prototype to `broadcom.c` and removing it from `mainboard.c` fixes the warning. Change-Id: I1da0c4e972e129047dd8230d573f1c43fd71eb20 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2952 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29inteltool: Support GPIO registers on Cougar/Panther PointNico Huber
This adds the GPIO register definitions for Intel's Cougar Point and Panther Point platform controller hubs (PCH). All information is taken from the public specifications in [1] and [2]. I've tested it with an H77 PCH. NM70 is missing in [1]. Therefore, I didn't add it here. [1] Intel 6 Series Chipset and Intel C200 Series Chipset - Datasheet Document-Number: 324645-006 [2] Intel 7 Series / C216 Chipset Family Platform Controller Hub (PCH) - Datasheet Document-Number: 326776-003 Change-Id: I31711e24f852e68b3c113e3bd9243dc7e89ac197 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/2961 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29inteltool: Add definitions for Cougar/Panther Point PCI IDsNico Huber
This adds correspondings #defines for the PCI IDs of the LPC device on Intel's Cougar Point and Panther Point platform controller hubs. Those will be used more in later commits. I've checked all those IDs against the specification updates [1] and [2]. [1] Intel 6 Series Chipset and Intel C200 Series Chipset Specification Update Document-Number: 324646-019 [2] Intel 7 Series / C216 Chipset Family Platform Controller Hub (PCH) Family - Datasheet Specification Update Document-Number: 326777-010 Change-Id: Ibef5a30d283c568c345eb8d8149723e7a3049272 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/2960 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29google boards: auto-select CACHE_ROMAaron Durbin
Automatically select CACHE_ROM for all Google boards. Tested by generating a config for the link board. CACHE_ROM was selected and was unable to unselect it using 'make oldconfig'. Change-Id: I8e34207e3929a020bb0280657f95ba7a000ad024 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2963 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-29x86: mtrr: optimize hole carving above 4GiBAaron Durbin
There is an optimization that can take place when hole carving in ranges above 4GiB. If the range is the last range then there is no need to carve UC holes out from the larger WB range. This optimization also has the same assumption of choosing WB as the default MTRR type: the OS needs to properly handle accessing realloacted MMIO resources with PAT so that the MTRR type can be overidden. Below are results using a combination of options. The board this was tested on has 10 variable MTRRs at its disposal. It has 4GiB of RAM. IO hole config #1: hole starts at 0xad800000 No CACHE_ROM and no WRCOMB resources (takes 4 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6 0x00000000ad800000 - 0x0000000100000000 size 0x52800000 type 0 0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6 MTRR: default type WB/UC MTRR counts: 4/6. MTRR: WB selected as default type. MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0 MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0 MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0 MTRR: 3 base 0x00000000c0000000 mask 0x0000007fc0000000 type 0 No CACHE_ROM and 1 WRCOMB resource (takes 6 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6 0x00000000ad800000 - 0x00000000d0000000 size 0x22800000 type 0 0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1 0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0 0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6 MTRR: default type WB/UC MTRR counts: 6/7. MTRR: WB selected as default type. MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0 MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0 MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0 MTRR: 3 base 0x00000000c0000000 mask 0x0000007ff0000000 type 0 MTRR: 4 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1 MTRR: 5 base 0x00000000e0000000 mask 0x0000007fe0000000 type 0 CACHE_ROM and no WRCOMB resources (takes 7 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6 0x00000000ad800000 - 0x00000000ff800000 size 0x52000000 type 0 0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5 0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6 MTRR: default type WB/UC MTRR counts: 11/7. MTRR: UC selected as default type. MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6 MTRR: 1 base 0x0000000080000000 mask 0x0000007fe0000000 type 6 MTRR: 2 base 0x00000000a0000000 mask 0x0000007ff0000000 type 6 MTRR: 3 base 0x00000000ad800000 mask 0x0000007fff800000 type 0 MTRR: 4 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0 MTRR: 5 base 0x00000000ff800000 mask 0x0000007fff800000 type 0 MTRR: 6 base 0x0000000100000000 mask 0x0000007f00000000 type 6 CACHE_ROM and 1 WRCOMB resource (takes 8 MTRRs): Previously this combination was impossible without the optimization. MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6 0x00000000ad800000 - 0x00000000d0000000 size 0x22800000 type 0 0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1 0x00000000e0000000 - 0x00000000ff800000 size 0x1f800000 type 0 0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5 0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6 MTRR: default type WB/UC MTRR counts: 12/8. MTRR: UC selected as default type. MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6 MTRR: 1 base 0x0000000080000000 mask 0x0000007fe0000000 type 6 MTRR: 2 base 0x00000000a0000000 mask 0x0000007ff0000000 type 6 MTRR: 3 base 0x00000000ad800000 mask 0x0000007fff800000 type 0 MTRR: 4 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0 MTRR: 5 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1 MTRR: 6 base 0x00000000ff800000 mask 0x0000007fff800000 type 0 MTRR: 7 base 0x0000000100000000 mask 0x0000007f00000000 type 6 IO hole config #1: hole starts at 0x80000000 No CACHE_ROM and no WRCOMB resources (takes 1 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6 0x0000000080000000 - 0x0000000100000000 size 0x80000000 type 0 0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6 MTRR: default type WB/UC MTRR counts: 1/2. MTRR: WB selected as default type. MTRR: 0 base 0x0000000080000000 mask 0x0000007f80000000 type 0 No CACHE_ROM and 1 WRCOMB resource (takes 3 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6 0x0000000080000000 - 0x00000000d0000000 size 0x50000000 type 0 0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1 0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0 0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6 MTRR: default type WB/UC MTRR counts: 4/3. MTRR: UC selected as default type. MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6 MTRR: 1 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1 MTRR: 2 base 0x0000000100000000 mask 0x0000007f00000000 type 6 CACHE_ROM and no WRCOMB resources (takes 3 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6 0x0000000080000000 - 0x00000000ff800000 size 0x7f800000 type 0 0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5 0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6 MTRR: default type WB/UC MTRR counts: 9/3. MTRR: UC selected as default type. MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6 MTRR: 1 base 0x00000000ff800000 mask 0x0000007fff800000 type 0 MTRR: 2 base 0x0000000100000000 mask 0x0000007f00000000 type 6 CACHE_ROM and 1 WRCOMB resource (takes 4 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6 0x0000000080000000 - 0x00000000d0000000 size 0x50000000 type 0 0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1 0x00000000e0000000 - 0x00000000ff800000 size 0x1f800000 type 0 0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5 0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6 MTRR: default type WB/UC MTRR counts: 10/4. MTRR: UC selected as default type. MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6 MTRR: 1 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1 MTRR: 2 base 0x00000000ff800000 mask 0x0000007fff800000 type 0 MTRR: 3 base 0x0000000100000000 mask 0x0000007f00000000 type 6 Change-Id: Ia3195af686c3f0603b21f713cfb2d9075eb02806 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2959 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29x86: mtrr: add hole punching supportAaron Durbin
Some ranges would use less variable MTRRs if an UC area can be carved off the top of larger WB range. Implement this approach by doing 3 passes over each region in the addres space: 1. UC default type. Cover non-UC and non-WB regions with respectie type. Punch UC hole at upper end of larger WB regions with WB type. 2. UC default type. Cover non-UC regions with respective type. 3. WB default type. Cover non-WB regions with respective type. The hole at upper end of a region uses the same min alignment of 64MiB. Below are results using a combination of options. The board this was tested on has 10 variable MTRRs at its disposal. It has 4GiB of RAM. IO hole config #1: hole starts at 0xad800000 No CACHE_ROM or WRCOMB resources (takes 4 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6 0x00000000ad800000 - 0x0000000100000000 size 0x52800000 type 0 0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6 MTRR: default type WB/UC MTRR counts: 4/9. MTRR: WB selected as default type. MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0 MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0 MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0 MTRR: 3 base 0x00000000c0000000 mask 0x0000007fc0000000 type 0 No CACHE_ROM. 1 WRCOMB resource (takes 6 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6 0x00000000ad800000 - 0x00000000d0000000 size 0x22800000 type 0 0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1 0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0 0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6 MTRR: default type WB/UC MTRR counts: 6/10. MTRR: WB selected as default type. MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0 MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0 MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0 MTRR: 3 base 0x00000000c0000000 mask 0x0000007ff0000000 type 0 MTRR: 4 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1 MTRR: 5 base 0x00000000e0000000 mask 0x0000007fe0000000 type 0 CACHE_ROM and no WRCOMB resources (taks 10 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6 0x00000000ad800000 - 0x00000000ff800000 size 0x52000000 type 0 0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5 0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6 MTRR: default type WB/UC MTRR counts: 11/10. MTRR: UC selected as default type. MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6 MTRR: 1 base 0x0000000080000000 mask 0x0000007fe0000000 type 6 MTRR: 2 base 0x00000000a0000000 mask 0x0000007ff0000000 type 6 MTRR: 3 base 0x00000000ad800000 mask 0x0000007fff800000 type 0 MTRR: 4 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0 MTRR: 5 base 0x00000000ff800000 mask 0x0000007fff800000 type 0 MTRR: 6 base 0x0000000100000000 mask 0x0000007fc0000000 type 6 MTRR: 7 base 0x0000000140000000 mask 0x0000007ff0000000 type 6 Taking a reserved OS MTRR. MTRR: 8 base 0x000000014f600000 mask 0x0000007fffe00000 type 0 Taking a reserved OS MTRR. MTRR: 9 base 0x000000014f800000 mask 0x0000007fff800000 type 0 A combination of CACHE_ROM and WRCOMB just won't work. IO hole config #2: hole starts at 0x80000000: No CACHE_ROM or WRCOMB resources (takes 1 MTRR): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6 0x0000000080000000 - 0x0000000100000000 size 0x80000000 type 0 0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6 MTRR: default type WB/UC MTRR counts: 1/5. MTRR: WB selected as default type. MTRR: 0 base 0x0000000080000000 mask 0x0000007f80000000 type 0 No CACHE_ROM. 1 WRCOMB resource (takes 4 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6 0x0000000080000000 - 0x00000000d0000000 size 0x50000000 type 0 0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1 0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0 0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6 MTRR: default type WB/UC MTRR counts: 4/6. MTRR: WB selected as default type. MTRR: 0 base 0x0000000080000000 mask 0x0000007fc0000000 type 0 MTRR: 1 base 0x00000000c0000000 mask 0x0000007ff0000000 type 0 MTRR: 2 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1 MTRR: 3 base 0x00000000e0000000 mask 0x0000007fe0000000 type 0 CACHE_ROM and no WRCOMB resources (takes 6 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6 0x0000000080000000 - 0x00000000ff800000 size 0x7f800000 type 0 0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5 0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6 MTRR: default type WB/UC MTRR counts: 9/6. MTRR: UC selected as default type. MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6 MTRR: 1 base 0x00000000ff800000 mask 0x0000007fff800000 type 0 MTRR: 2 base 0x0000000100000000 mask 0x0000007f80000000 type 6 MTRR: 3 base 0x000000017ce00000 mask 0x0000007fffe00000 type 0 MTRR: 4 base 0x000000017d000000 mask 0x0000007fff000000 type 0 MTRR: 5 base 0x000000017e000000 mask 0x0000007ffe000000 type 0 CACHE_ROM and 1 WRCOMB resource (takes 7 MTRRs): MTRR: Physical address space: 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6 0x0000000080000000 - 0x00000000d0000000 size 0x50000000 type 0 0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1 0x00000000e0000000 - 0x00000000ff800000 size 0x1f800000 type 0 0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5 0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6 MTRR: default type WB/UC MTRR counts: 10/7. MTRR: UC selected as default type. MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6 MTRR: 1 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1 MTRR: 2 base 0x00000000ff800000 mask 0x0000007fff800000 type 0 MTRR: 3 base 0x0000000100000000 mask 0x0000007f80000000 type 6 MTRR: 4 base 0x000000017ce00000 mask 0x0000007fffe00000 type 0 MTRR: 5 base 0x000000017d000000 mask 0x0000007fff000000 type 0 MTRR: 6 base 0x000000017e000000 mask 0x0000007ffe000000 type 0 Change-Id: Iceb9b64991accf558caae2e7b0205951e9bcde44 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2925 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29memrange: add 2 new range_entry routinesAaron Durbin
Two convenience functions are added to operate on a range_entry: - range_entry_update_tag() - update the entry's tag - memranges_next_entry() - get the next entry after the one provide These functions will be used by a follow on patch to the MTRR code to allow hole punching in WB region when the default MTRR type is UC. Change-Id: I3c2be19c8ea1bbbdf7736c867e4a2aa82df2d611 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2924 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29chromeos: remove CACHE_ROM automatic selectionAaron Durbin
It's not appropriate for the chromeos Kconfig to automatically select CACHE_ROM. The reason is that enabling CACHE_ROM is dependent on the board and chipset atrributes. Change-Id: I47429f1cceefd40226c4b943215d627a3c869c7b Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2921 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-29libpayload: add x86 ROM variable MTRR supportAaron Durbin
On x86, coreboot may allocate a variable range MTRR for enabling caching of the system ROM. Add the ability to parse this structure and add the result to the sysinfo structure. An example usage implementation would be to obtain the variable MTRR index that covers the ROM from the sysinfo structure. Then one would disable caching and change the MTRR type from uncacheable to write-protect and enable caching. The opposite sequence is required to tearn down the caching. Change-Id: I3bfe2028d8574d3adb1d85292abf8f1372cf97fa Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2920 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 10:58:08 +0000