Age | Commit message (Collapse) | Author |
|
If the Host Command payload is less than 4 bytes
and is word aligned then the payload was not transferred at all.
EC reads the old packet and CRC mismatch occurs.
In this issue, the HC command packet
consisting of EC_CMD_REBOOT_EC as command and EC_REBOOT_COLD
as payload encountered the same problem as above.
Hence select byte access mode for shorter payloads.
BRANCH=None
BUG=chrome-os-partner:42396
TEST=System should boot after
chromeos-firmwareupdate
Change-Id: I22bdb739108d31b592c20247be69c198d617d359
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8a43d2636b1bbfbac0384e1ea5e8853a7bd87a7f
Original-Change-Id: I5572093436f4f4a0fc337efa943753ab4642d8e4
Original-Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Signed-off-by: Icarus Sparry <icarus.w.sparry@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/286537
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/11012
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Log the global reset causes in the power state structure.
While working in there pack the struct and use width-specific
types as this struct crosses the romstate <-> ramstage boundary.
Lastly, remove hsio version as it wasn't being written or read.
After global reset induced:
PM1_STS: 0000
PM1_EN: 0000
PM1_CNT: 00000000
TCO_STS: 0000 0000
GPE0_STS: 00000000 00000000 00000000 00000000
GPE0_EN: 00000000 00000000 00000000 00000000
GEN_PMCON: d8010200 00003808
GBLRST_CAUSE: 00000000 00040004
Previous Sleep State: S0
BUG=None
BRANCH=None
TEST=Induced global reset on glados using ETR3 register and write
to cf9.
Change-Id: I97b93de336e74c0e02199241376e74340612f0a7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: bbc8f1d62131c0381e9d401f3281ee7a17fc2a47
Original-Change-Id: I1a8e5d07c6c0e09c163effe27491d8f198823617
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/286640
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/11011
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The GPIO mapping was incorrect for wpsw_cur.
The GPIOs for East community were in two ranges:
0: INT33FF:02 GPIOS [373 - 384] PINS [0 - 11] and
12: INT33FF:02 GPIOS [385 - 396] PINS [15 - 26]
The discontinuity was not accounted for, hence the error.
The original offset was 0x16 whereas it should be 0x13
BUG=chrome-os-partner:42798
BRANCH=None
TEST=Run crossystem and test wpsw_cur entry. If screw is present,
it should be 1 and if not present, it should be 0
Change-Id: I2faea1fe1415c9d4cb23444d03c7c9d47c87e8e5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 30ac96f606a5618e9ef12bac3f50fac433141acd
Original-Change-Id: I166a7c3e15a990b507ae3c13e15ab56bee7fb917
Original-Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/286534
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/11010
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Document the lid open state and separate the routines with a single
blank line.
BRANCH=none
BUG=None
TEST=Build and run on Kunimitsu
Change-Id: I244f20c03bc7530ad8d140fba41dd97c12c079e1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 57313253fdef3f2d3f0e16b8ab8aa91202d45b16
Original-Change-Id: I7b3bd9cf16e915d214eb2de0017a8d91a934b112
Original-Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/286267
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Original-Commit-Queue: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Tested-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Reviewed-on: http://review.coreboot.org/11009
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Remove the address from the copyright notices.
BRANCH=none
BUG=None
TEST=Build and run on Kunimitsu
Change-Id: Ibe8196841d9e76c9ee3a3dbae802ecc63dc7904c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cc12d2658324a375d02748098f0a2f4b5d1b5615
Original-Change-Id: I81a71e4ad9b8a66ad0e9a93cbeb512d90eb35906
Original-Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/286266
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Original-Commit-Queue: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Tested-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Reviewed-on: http://review.coreboot.org/11008
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Tested-by: build bot (Jenkins)
|
|
If a resume from S3 is occuring one needs to take into account
deep S3 in order to check the proper power failure bits.
When deep S3 is enabled the suspend well will be turned off.
Therefore don't look for that bit when determining a power
failure.
BUG=chrome-os-partner:42847
BRANCH=None
TEST=Suspend and resumed with deep s3 enabled and disabled.
Change-Id: I2b3372a40b3d8295ee881a283b31ca7704e6764a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a3ba22be37d8700f4e8a4a0f5c05fb9290cfc9b2
Original-Change-Id: I890f71a7cbea65f1db942fe2229a220cf0e721b0
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/286271
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/11007
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
GEN_PMCON_A and GEN_PMCON_B are 32-bits wide. Read out and
save the full 32 bits for completeness.
BUG=chrome-os-partner:42847
BRANCH=None
TEST=Built and booted. Noted output on terminal.
Change-Id: I24e589271d49c8cfc3fab327cfe4999c24fb95d8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5a419b2538dc45b1bd0d19b7e6afd45fff9dd4a0
Original-Change-Id: Ie587e886ea34e36d106ff4670781467266a51ddb
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/286270
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/11006
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Charger performance states table defines charger current limit for each
p state. Modify charger current control values for SANYO battery used
in Cyan.
BUG=None
BRANCH=None
TEST=System is charging battery, in shell window, issue command
"echo 0 > /sys/class/thermal/cooling_device4/cur_state",
"echo 1 > /sys/class/thermal/cooling_device4/cur_state",
"echo 2 > /sys/class/thermal/cooling_device4/cur_state",
"echo 3 > /sys/class/thermal/cooling_device4/cur_state", or
"echo 4 > /sys/class/thermal/cooling_device4/cur_state", will see EC
console show different charging current value.
Change-Id: Ie9bc78822a73de6bed338bfbcc5e9045653689dc
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3a6162151d1f9c756a13d2afc17f6b9c18608efc
Original-Change-Id: I71e8247d057e4728eedcd5e8a275b64428290d09
Original-Signed-off-by: li feng <li1.feng@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/285605
Original-Reviewed-by: Icarus W Sparry <icarus.w.sparry@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Original-Commit-Queue: Divya Jyothi <divya.jyothi@intel.com>
Original-Tested-by: Divya Jyothi <divya.jyothi@intel.com>
Reviewed-on: http://review.coreboot.org/11004
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch updates the Serial IO modes for UART2 to PCI mode
in devicetree for glados board.
Also we switch over to CONSOLE_SERIAL8250MEM_32 here. 8-bit
legacy UART will stop working after devicetree change.
BRANCH=None
BUG=chrome-os-partner:40857
TEST=Built for glados and tested LPSS logs on glados.
CQ-DEPEND=CL:284881 CL:284882 CL:284883
Change-Id: I433979c852c80848c006ef089b43d75a17e761c5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2c37519e0762801cbb9b547b538b385c84299189
Original-Change-Id: I2faec08d089e407c5ab9838bea980553f49821c4
Original-Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.ch@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/284826
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Wenkai Du <wenkai.du@intel.com>
Original-Tested-by: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: http://review.coreboot.org/11002
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch updates the Serial IO modes for UART 1 and 2
in devicetree for kunimitsu boards.
UART1 are disabled and
UART2 is in PCI mode.
BRANCH=None
BUG=chrome-os-partner:40857
TEST=Built for kunimitsu and tested LPSS logs on Kunimitsu.
Change-Id: I5a46ab9e0b792478ee2e0845aeab1443423a2fac
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 38c7b963a9d679ee5106c5343e1173d0b5056627
Original-Change-Id: I39cbb6bb0991e5f9b3365adaf6b24818d112cd1a
Original-Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.ch@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/284825
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Wenkai Du <wenkai.du@intel.com>
Original-Tested-by: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: http://review.coreboot.org/11001
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch updates the Serial IO modes for UART 1 and 2
in devicetree for sklrvp boards.
UART1 is disabled and
UART2 is in PCI mode.
BRANCH=None
BUG=chrome-os-partner:40857
TEST=Built for sklrvp and tested LPSS logs on RVP3.
Change-Id: I59a657d6a3744040ec6be290ba966672e0e5f17e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5a20a70801d66abd87d4214e1ef187b86eed99da
Original-Change-Id: I381374272e1824ca8887ea5c5662215dde2c0a56
Original-Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.ch@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/284824
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Wenkai Du <wenkai.du@intel.com>
Original-Tested-by: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: http://review.coreboot.org/11000
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch adds 32bit uart8250_mem functionality in romstage
console for arch/x86.
BRANCH=None
BUG=chrome-os-partner:40857
TEST=Built for sklrvp; verified romstage logs on RVP3 board.
Change-Id: I6f13216b7f5ba8de48c781cd1791d0fa7ae0d921
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a17efdeec5524cbfc78015c358d1cf4f67485765
Original-Change-Id: I8b4e44c59bfd609a06807243df338763054b5865
Original-Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.ch@intel.com>
Original-Signed-off-by: Rishavnath Satapathy <rishavnath.satapathy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/271800
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Wenkai Du <wenkai.du@intel.com>
Original-Tested-by: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: http://review.coreboot.org/10999
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch adds UART8250MEM_32 feature flag to support
UART8250 compatible with 32bit access in memory mapped mode.
[pg: rebuilt to reuse the existing UART8250 8bit access driver
which reduces code duplication.]
Change-Id: I310e70dfab81dcca575e9931e0ccf93af70efa40
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0c3b2c628b854e8334540ff5158c2587dbfabf95
Original-Change-Id: I07ee256f25e48480372af9a9255bf487c331e51d
Original-Signed-off-by: Rishavnath Satapathy <rishavnath.satapathy@intel.com>
Original-Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.ch@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/271759
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Wenkai Du <wenkai.du@intel.com>
Original-Commit-Queue: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: http://review.coreboot.org/10998
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I0c196ff84484717c59c59d11bb7230b5920e0654
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10997
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
printk called before console init causes sluggish execution because
of Rx timeout.
BRANCH=None
BUG=chrome-os-partner:40857
TEST=Built for sklrvp and tested LPSS logs on RVP3 and Kunimitsu.
Change-Id: I61d5c0f5a4e93695bcba90b7ac7d4f68e2d625be
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 77c58702c8279c6d9c6ae1c946bf1b76df20714d
Original-Change-Id: Ib85029456059248cc2c88aaccba4fa12cc5a76be
Original-Signed-off-by: rsatapat <rishavnath.satapathy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/284823
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Wenkai Du <wenkai.du@intel.com>
Original-Tested-by: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: http://review.coreboot.org/10996
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
FSP will initialize GPIOs during TempRamInit.
So configure LPSS UART2 GPIOs in native mode
after TempRamInit.
BRANCH=none
BUG=chrome-os-partner:41374
EST=Build and boot on RVP3. Check LPSS logs on UART2
Change-Id: I8016dd76a5bc06e90f9460273be7e83c5e8f8bb1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: eb72e715ef3f566e900727ac8b9494bca1d5971c
Original-Change-Id: If1b1a1047ebd5e5f170d91972d11c51aa6fd84a9
Original-Signed-off-by: rsatapat <rishavnath.satapathy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/281604
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Wenkai Du <wenkai.du@intel.com>
Original-Tested-by: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: http://review.coreboot.org/10995
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
On Skylake, only UART2 is supported as debug port and the macros
INTEL_PCH_UART_CONSOLE_NUMBER, INTEL_PCH_UART_CONSOLE and the partial
code for UART0, 1 are cleaned up for Skylake and Sklrvp, Kunimitsu and
Glados boards.
BRANCH=none
BUG=chrome-os-partner:40857
TEST=Built for kunimitsu, checked the coreboot logs on LPSS UART2
Change-Id: I2fbcfb1d1ca6f59309a77c67d022cf4f5da7f7c0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e714c18d462bc7bdd7068309fb6be77da6973642
Original-Change-Id: I9343abd90ce685ea2d676047dccbefad7457b69f
Original-Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.ch@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/285793
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Wenkai Du <wenkai.du@intel.com>
Original-Tested-by: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: http://review.coreboot.org/10994
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
FSP 1.1 platforms should be conforming to the spec. In order
to ensure following specification remove the crutch that allows
FSP to no conform.
BUG=chrome-os-partner:41961
BRANCH=None
TEST=Built.
Change-Id: I28b876773a3b6f07223d60a5133129d8f2c75bf6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c3fe08c5af41867782e422f27b0aed1b762ff34a
Original-Change-Id: Ib97027a35cdb914aca1eec0eeb225a55f51a4b4b
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/285187
Original-Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/10993
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Disabling the wwan gpio line
since wwan is not used.
BRANCH=none
BUG=none
TEST=wwan should not connect to network on cyan/strago.
Change-Id: I9d2e5d5b185a4622218e894d3b092afe15e09289
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9a20c602b3bb768baa38b17e21cb4e5b0d9249ef
Original-Change-Id: Ib8d5fd15a172ef898ce675a85c2ea3e5f5c79144
Original-Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/285304
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10992
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Removing GOP initialization in normal mode since we don't need to
show splash screen in normal mode. GOP will get initialized in dev
and recovery mode.
BRANCH=none
BUG=None
TEST=Splash screen will come only in dev or recovery mode.
Change-Id: Ia5e12cf45d723f2f14c447e29b78119552d5e1ea
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 79d1c877343704ea51143b922d9ac9209be4d4b5
Original-Change-Id: Id5ca99757427206413483d07b4f422b4c0abfa5d
Original-Signed-off-by: Abhay <abhay.kumar@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/285300
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10990
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All boards should have their L1 sub states working now so
re-enable the defaults.
BUG=chrome-os-partner:41861
BRANCH=None
TEST=Built and booted glados into OS. PCIe devices show up still.
Change-Id: Ic040fa108a662e15bb97cf8b0961f0f56683e146
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 380491f8267e60c3c6bc62486aaf21e201fcfd36
Original-Change-Id: Idc6923b1fdd1c20d463eb7782be112f90b9adbfd
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/285170
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/10989
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch selects the config symbol PCIEXP_L1_SUB_STATE to enable L1
substate for PCIe.
BRANCH=None
BUG=chrome-os-partner:42331
TEST=Build for sklrvp; boot and check "dmesg | grep iwl" shows
"L1 enabled and LTR enabled"
Change-Id: I97552c7700649a9f5d8646a03027c5c5e0b477b4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d3115816fbdd11c7f8ff418e0b5c86b8650c8b83
Original-Change-Id: Iaf307cb2d623cc1ce97b01d15a6b42569fd0c0c4
Original-Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.ch@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/284775
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: http://review.coreboot.org/10988
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
For some unkonwn reason the pcie root port settings weren't
being honored in the device tree. Fix that omission.
BUG=chrome-os-partner:41861
BRANCH=None
TEST=Built with CONFIG_DISPLAY_UPD_DATA and noted devicetree
settings were being honored.
Change-Id: Id880eca57544efb13f5cbbc06b2634c86b7c5d29
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2d00e68ce6cfcb3d63d69848f4a8ce232f6c1257
Original-Change-Id: Idd37d65374842294f4b0c91eb841c6d1d93e92ee
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/285027
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/10987
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Unhide the SPI controller PCI device if it is enabled in
devicetree.cb so flashrom can do its job.
BUG=chrome-os-partner:37711
BRANCH=none
TEST=run flashrom -r on glados
Change-Id: Ie567f970149700d29df0ae09db4962f36cf24219
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 172eac55ad6134fe5e347e37c055b383e3b03245
Original-Change-Id: Ia77b559cc607794aecc25d6d469224d855199568
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/284948
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10986
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=chrome-os-partner:40526
BRANCH=None
TEST=Verify that system boots when used with coreboot and EC
versions that also have Software Sync enabled.
Change-Id: I6ed562fa51d83ddf16fc74d35db7c0004f57c79e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 090a66c50fac21808c4721a32b1728cc904f1b00
Original-Change-Id: Ia4d87d9a177c579567c03ae113889a277ffecee0
Original-Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/283573
Original-Commit-Queue: Divya Jyothi <divya.jyothi@intel.com>
Original-Tested-by: Divya Jyothi <divya.jyothi@intel.com>
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/10985
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is breaking the build right now. Reapply once the correct headers are in place.
This reverts commit 406effd59075cab212c5bf9c1a12759c8fad50a4.
Change-Id: I34b8717820ed58b462d4e7793711ee98fb8b882f
Reviewed-on: http://review.coreboot.org/11020
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Fix typo. Use the correct math helper int-lt.
Change-Id: Ia5e722020c75595dfcfb853ea8238fb8391f9a04
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10980
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
All \_PR entries needs to be changed from CPU# to CP##
so that it can support more cores.
BRANCH=none
BUG=chrome-os-partner:38734
TEST=build and boot cyan/strago boards.
Change-Id: I80a79ec8edbce46826140470645b7532ae361f91
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ca269a7ffcd2ef16fcef93851e68c2d91104e3e1
Original-Change-Id: I48e73742dc3b11ee6e96f70bcd2d10d01609ad7c
Original-Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/285700
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10991
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This adds support for binarypi based boards that have
to make adjustments to the memory configuration settings.
A PlatformMemoryConfiguration[] table that describes
the memory configuration must be defined in the
mainboard folder.
Change-Id: I5e4b476a4adf3dd1f3b7843274a81ecb243d10ab
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/10672
Tested-by: build bot (Jenkins)
Reviewed-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The code for removing a file had its own merge routine. Use the generic one
instead.
Change-Id: I90ed007ab86f78a2728f529fa0143c5c1dfbbdc3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/10967
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
So far it's still unused, but its purpose will change:
It will become an offset to another structure that contains additional file
attributes.
This change is compatible because the binary format doesn't change and so far
the field was always set to 0, which can serve nicely as 'unused' field.
Change-Id: I2dafb06866713d43a236556f9492641526270837
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10933
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This makes the Makefile more robust when changing the file name
or changing the .config outside of make *config
Change-Id: Ifc013cc3ef899a7846742a961261ac50bc67e27b
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10970
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch adds support for the SuperSpeed half of USB 3.0 hubs, which
previously prevented SuperSpeed devices behind those hubs from working.
BRANCH=None
BUG=chrome-os-partner:39877
TEST=Played around with multiple hubs and devices on Oak and Falco, can
no longer find a combination that doesn't work.
Change-Id: I20815be95769e33d399b7ad91c3020687234e059
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3db96ece20d2304e7f6f6aa333cf114037c48a3e
Original-Change-Id: I2dd6c9c3607a24a7d78c308911e3d254d5f8d91d
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/284577
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: chunfeng yun <chunfeng.yun@mediatek.com>
Reviewed-on: http://review.coreboot.org/10958
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We have been trying to avoid reassigning previously used USB addresses
to different devices since CL:197420, because some devices seem to take
issue with that. Unfortunately, that patch doesn't affect XHCI: those
controllers insist on chosing addresses on their own. The only way to
prevent them from reusing a previously assigned address is to not
disable that slot at all.
This patch implements address reuse avoidance on XHCI by not disabling
slots when a device is detatched (which may occur both on physical
detachment or if we simply couldn't find a driver for that device).
Instead, we just release as many resources as we can for detached
devices (by dropping all endpoint contexts) and defer the final cleanup
until the point where the controller actually runs out of resources (a
point that we probably don't often reach in most firmware scenarios).
BRANCH=none
BUG=chrome-os-partner:42181
TEST=Booted an Oak plugged into a Servo without having a driver for the
SMSC network chip, observed that it could still enumerate the next
device afterwards. Kept unplugging/replugging stuff until the cleanup
triggered and made sure the controller still worked after that. Also
played around a bit on a Falco without issues.
Change-Id: Idfbab39abbc5bc5eff822bedf9c8d5bd4cad8cd2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 88c6bcbc41156729c3c38937c8a4adebc66f1ccb
Original-Change-Id: I0653a4f6a02c02498210a70ffdda9d986592813b
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/284175
Original-Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10957
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The new attributes increase the header size, breaking this assumption.
Change-Id: Ib23862f27650b39133deafb74a24327b098b6e86
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10942
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change-Id: Ie05db6d43219c65d08e2221009875f81eb29b630
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/10968
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BOOT_MEDIA_SPI_BUS is int, not hex.
Change-Id: I5cbcc3889a025caab921208037c8a61d224078a7
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/10973
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
They have been removed in the rest of the code already.
http://review.coreboot.org/#/c/4506/
Change-Id: I232cc2ccd4dd90359de4ab710486db65667500f4
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10964
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: If933a70992a6ae8228eef8d4f0386387b4e4549d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/10966
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Found by the commit hooks.
Change-Id: I9baa90ca0111ddc9cb69cbb7dd17f63e8a98a04f
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10965
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add initial files for the cyan board.
Matches chromium tree at 927026db
This board uses the Braswell FSP 1.1 image and does not build
without the FspUpdVpd.h file.
BRANCH=none
BUG=None
Test=Build and run on cyan
Change-Id: I935839be033c25e197e78fbee306104b4162a99a
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: http://review.coreboot.org/10182
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Initial files to support the Kunimitsu board.
Matches chromium tree at 927026db
This board uses the Skylake FSP 1.1 image and does not build without the
FspUpdVpd.h file.
BRANCH=none
BUG=None
TEST=Build and run ChromeOS on kunimitsu
Change-Id: I1017a66bc811af51a0921e864b589ce2cb618082
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: http://review.coreboot.org/10836
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Initial files to support the Intel Skylake RVP3
Matches chromium tree at 927026db
This board uses the Skylake FSP 1.1 image and does not build without the
FspUpdVpd.h file.
BRANCH=none
BUG=None
TEST=Build and run on sklrvp
Change-Id: I5e7fff8f62a737e627e25c1e03e343d6167041ea
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: http://review.coreboot.org/10343
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add the initial files to support the Intel RVP for Braswell.
Matches chromium tree at 927026db
This board uses the Braswell FSP 1.1 image and does not build without
the FspUpdVpd.h file.
BRANCH=none
BUG=None
TEST=Build and run ChromeOS on strago
Change-Id: I5cb2efe3d8adf919165c62b25e08c544b316a05a
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: http://review.coreboot.org/10052
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch enables running the checkpatch script on the code portion
of each commit as part of the pre-commit hook. At this point there
is no checking of the commit message in place (e.g. for typos)
Change-Id: I7cdf0692cf372986e411f4aba4691417b73c7511
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/8419
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change-Id: I2821aaed1bc6324e671f68e4e4effb9dd006dcd9
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10922
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The BROKEN_CAR_MIGRATE symbol was removed in commit a6371940 -
x86 cache-as-ram: Remove BROKEN_CAR_MIGRATE option
The symbol DISABLE_SANDYBRIDGE_HYPERTHREADING is from Sage, and was
never added to the coreboot.org codebase.
Change-Id: I953fe7c46106634a5a3fcdaff88b39e884f152e6
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10941
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
With split transaction, dwc2 host controller can handle full- and
low-speed devices on hub in high-speed mode. This commit adds support
for split control and interrupt transfers
BUG=None
TEST=Connect usb keyboard through hub, usb keyboard can work
BRANCH=None
Change-Id: If7a00db21c8ad4c635f39581382b877603075d1a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4fb514b7f7f7e414fa94bfce05420957b1c57019
Original-Change-Id: I07e64064c6182d33905ae4efb13712645de7cf93
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/283282
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/10956
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
New sdram_lp0_save_params() function for T210.
Due to its size, move the function from romstage to ramstage.
BUG=chrome-os-partner:40741
BRANCH=None
TEST=Build ok on Smaug; and check scratch registers
Change-Id: I420ac4c15262f2c6307bcd84beb6c5da0310c7c0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 38860895938c40062a9f860f75e31a539f15992b
Original-Change-Id: Iaa478969458946faedd295578fe7d72b5a32e701
Original-Signed-off-by: Yen Lin <yelin@nvidia.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/277022
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/10952
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
So odmdata has the correct UART port of 0
BUG=chrome-os-partner:40741
BRANCH=None
TEST=build Foster ok; and check scratch20 register
Change-Id: I2c203317e6305214b74430780f2fe7b15652873a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0a0a99ac9c7db267129e4bc3478f9bb1ece08507
Original-Change-Id: I7be10d5deb5118f1cf3e339afca94893610437f2
Original-Signed-off-by: Yen Lin <yelin@nvidia.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/280291
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/10955
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|