summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-03-13libpayload: ARCH-$(CONFIG_ARCH_ARMV7) was defined twice, make one POWERPCGabe Black
Change-Id: Ia85a7cd6a0b85119cce6b2f9c42a7fc31ffd9f97 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2654 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayload: Add usb_generic_(create|remove) functions for unrecognized devicesGabe Black
It might be useful to provide a USB driver in the payload itself instead of in libpayload. For example there are multiple payloads being built and linked against the same libpayload, and they might not need or even want to have the same set of drivers installed. This change adds two new functions, usb_generic_create and usb_generic_remove, which behave like the usbdisk_create and usbdisk_remove functions which are defined for USB mass storage devices. If a USB device isn't recognized and claimed by one of the built in USB class drivers (currently hub, hid, and msc) and the create function is defined, then it will be called to give the payload a chance to use the device. Once it's removed, if usb_generic_remove is defined it will be called, effectively giving the payload notice. Built and booted depthcharge on Link. Built depthcharge for Daisy. Built a netbooting payload, called usb_poll() with those functions implemented, and verified that they were called and that the devices they were told about were reasonable and the same as what was reported by lsusb in the booted system. Change-Id: Ief7c0a513b60849fbf2986ef4ae5c9e7825fef16 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2666 Tested-by: build bot (Jenkins) Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayload: Split EHCI bulk transfers on packet boundaries over qTDsJulius Werner
EHCI controllers see transfers as a queue of transfer descriptors (qTDs), each of which can represent an aligned area of up to 20KB. Each qTD is processed separately, which means that a single USB packet cannot span multiple qTDs. While this should not be a problem according to the specification, some USB storage devices seem to get confused when a packet in the middle of a transfer is smaller than the maximum packet size (512 bytes) due to falling on a qTD boundary. This patch aligns the total transfer length per qTD to 512 bytes to avoid that problem (any excess bytes will simply roll over to the next qTD). Change-Id: I0b5db07507699a3861b30c1a5ee774c45dda7fdd Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: http://review.coreboot.org/2651 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayload: add support for 64-bit EHCI controllersVincent Palatin
Initialize the high part of the address and use 64-bit compatible descriptors. (waste a few bytes on 32-bit but should be harmless) Read USB stick on a SandyBridge system which has 64-bit EHCI. Change-Id: I59cc842459acecdde8f8bdd4795ebfeccb842c8f Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2650 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayload: Stub out time keeping functions for ARM as wellGabe Black
These were currently stubbed out for PowerPC but not for ARM. Change-Id: I08f45174877bf5751d972078b8c53d82898b7f2b Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2655 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayload: If no video drivers initialize in video_init, return 1.Gabe Black
Change-Id: I56f810dfa6654ac1e9d1696ad15e7f1b8bfe59bd Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2652 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-13libpayload: If there's no IO address space, don't try to use it for serialGabe Black
Change-Id: I01b1fa42139af925716cd5d57f96dc24da6df5a7 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2660 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayload: If there's no IO space, complain if the serial claims to use itGabe Black
Change-Id: I36c750d520ff034c9ca9b9af46bd99bd49af7355 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2659 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayload: Consolidate io vs. mem mapped serial into accessor functionsGabe Black
This way we won't have two copies of the hardware init function, and three copies of the putchar, havechar, and getchar functions. Change-Id: Ifda7fec5d582244b0e163ee93ffeedeb28ce48da Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2657 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayload: Make whether or not there's an IO address space configurableGabe Black
Default it to no to be consistent with the other architecture wide options (endianness), and turn it on explicitly for x86 and PowerPC. Change-Id: Idda26d580156bbbf08ea11b28abe75cfa6b594b2 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2658 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13Update 3rdparty mark to latest repositoryStefan Reinauer
For google/stout binaries Change-Id: I4ef3f9cc35dfb6d27e1c9f074759f0e3ddee73c4 Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/2635 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayload: Start using only internal and compiler headers.Ronald G. Minnich
When building other payloads with lpgcc the -nostdinc flag was injected into CFLAGS, but when building libpayload itself some headers were being used from the host system. This change puts -nostdinc into the Makefile and xcompile script, fixes up one include path in include/inttypes.h, adds the compiler provided include directory to the include search path, and deletes the two now redundant stdint.h files. BUG=None TEST=With this and other changes, built libpayload and depthcharge for Daisy, Link, and Fox. BRANCH=None Change-Id: Ia7817fceab5297cd82ccc0d392330de0df61980e Signed-off-by: Gabe Black <gabeblack@google.com> Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-on: http://review.coreboot.org/2710 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-13libpayload: Add more parenthesis to the endian conversion macrosGabe Black
There weren't enough parenthesis in the macros so operations might only apply to the last part of an expression passed in as an argument. Change-Id: I5afb406f9409986e45bbbc598bcbd0dd8507ed35 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2665 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-13libpayload: Make the source for lzma decompression constGabe Black
Change-Id: I9a16331dedc97f17af94bf2cf535a9c93d1729a0 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2667 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-03-13src/mainboard: Drop redundant `CHIP_NAME` again for new portsPaul Menzel
Since commit »Drop redundant CHIP_NAME in mainboard.c« (a93c3fe7) [1] `CHIP_NAME` is unneeded for mainboards as the name is composed automatically in `src/devices/root_device.c` from the strings in Kconfig. Unfortunately the ports for Google Butterfly, Link and Parrot as as well as IEI PM-LX2-800-R10 introduced CHIP_NAME again. So drop it again too. [1] http://review.coreboot.org/1635 Change-Id: Ice7577a2a5c6070e196f2647c440b7a8e140e27e Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2708 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13libpayloads: Provide BSD/glibc style endian functions.Hung-Te Lin
The functions in endian.h (betoh{l,w,ll} and others) were named differently from the well-known BSD/glibc style endian functions (ex, betoh{16,32,64}). We should provide the BSD/glibc style functions to prevent confusion. Change-Id: Ia3bee481ba7989ac25b79ddb89bc6819d52fd8c3 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: http://review.coreboot.org/2705 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13exynos5250: Don't set PS_HOLD in bootblock_cpu_initDavid Hendricks
PS_HOLD gets set in exynos' power_init(). Change-Id: Ib08e0afcad23cbd07dc7e3727fd958a1bc868b5a Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2700 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-13exynos5250/snow: call PMIC's power_init() functionDavid Hendricks
Call the power_init() function. We appear to have forgotten about it when deprecating lowlevel_init_subsystems(), but it didn't seem to cause problems until we got to doing more interesting stuff recently. There are some clean-ups to do from the original code, such as not attempting to configure I2C from PMIC code, which we'll get around to in follow-up patches. (Credit to Gabe for spotting this) Change-Id: I6a59379e9323277d0b61469de9abe6d651ac5bfb Signed-off-by: Gabe Black <gabeblack@chromium.org> Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2699 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-12libpayload: Remove unnecessary include of arch/msr.hGabe Black
The functions defined in that header aren't used anywhere in the actual code, and that include breaks things on ARM. Built for ARM with COREBOOT_VIDEO_CONSOLE turned on and saw compiler errors go away. Change-Id: I56d6fe5e00c8fccda6e31ef8752326bd36398e74 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2656 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-12libpayload: In the USBMSC read_capacity function, make buf an array of u32.Gabe Black
That way when it's treated as a u32 when its value is extracted for numblocks and blocksize below, it doesn't make the compiler unhappy, and it ensures that the buffer will be properly aligned on architectures where that sort of thing matters. Built and saw warnings about type punning go away. Change-Id: I254e0b5e70847112d660675b7df0ac9cb52e4051 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: http://review.coreboot.org/2653 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-12AMD CIMx SB800: Enable AHCI mode for SATA controller by defaultPaul Menzel
The current default is IDE mode which is slower compared to AHCI mode. Therefore use AHCI mode by default. A similar change was made for AMD Persimmon in commit »Enable SATA AHCI for faster boot with SeaBIOS.« (96be74c7) [1] but was indirectly reverted by »sb800: Add sata ahci/raid mode kconfig option« (d4a0e7d0) [2]. [1] http://review.coreboot.org/220 [2] http://review.coreboot.org/225 Change-Id: I4fa31b0a3280891e7a3f37675ae8415205818947 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2661 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-12watchdog.h: Fix compile time error on disabling watchdog handlingPatrick Georgi
There's a compile time error that we didn't catch since the board defaults as used by the build bot won't expose it. Just make watchdog_off() a no-op statement so there aren't any stray semicolons in the preprocessor output. Change-Id: Ib5595e7e8aa91ca54bc8ca30a39b72875c961464 Reported-by: 'lautriv' on irc.freenode.net/#coreboot Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/2627 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-12libpayload: Fix reading x86 CBFS images from RAMPatrick Georgi
Three issues: 1. the hardcoded dereferenced pointer at 0xfffffffc 2. "RAM media" has no idea about ROM relative addresses 3. off-by-one in RAM media: it's legal to request 4 bytes from 0xfffffffc Change-Id: I671ac12d412c71dc8e8e6114f2ea13f58dd99c1d Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/2624 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2013-03-12Fix 'git describe' invocationVadim Bendebury
The 'git describe' command is used to obtain the source tree status information when building coreboot. As used this command expects git tags to be defined, so it can report the discrepancy between the current state of the tree and the latest tag. The problem is that the coreboot source tree does not have any git tags defined, so when 'git describe' is invoked, it reports "fatal: No names found, cannot describe anything.". This scary message can be seen on the console during coreboot builds. The solution is to add --always to the `git describe' invocation, which causes it to report the discrepancy with the latest sha1, if any, which is better than nothing. $ rm -rf /tmp/li && mkdir /tmp/li $ cp configs/config.link .config $ make obj=/tmp/li oldconfig $ make obj=/tmp/li $ grep COREBOOT_VERSION /tmp/li/build.h #define COREBOOT_VERSION "1623c06" $ echo '#' >> Makefile.inc $ grep COREBOOT_VERSION /tmp/li/build.h $ make obj=/tmp/li #define COREBOOT_VERSION "1623c06-dirty" $ git checkout Makefile.inc Change-Id: Ia77428b7cd765cbbd59bdbf8251b7bef489d47a5 Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: http://review.coreboot.org/2637 Tested-by: build bot (Jenkins)
2013-03-11pci.h: Drop unused `mainboard_pci_subsystem*` prototypesPatrick Georgi
We used to allow mainboards to override subsystems using mainboard_pci_subsystem_vendor_id and mainboard_pci_subsystem_device_id. Mechanisms have changed and the only occurrence of these names is in the header. Change-Id: Ic2ab13201a2740c98868fdf580140b7758b62263 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/2625 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins)
2013-03-11ASUS M5A88-V: Kconfig: Fix mainboard model namePaul Menzel
Despite everywhere the model name M5A88-V is used, in Kconfig the string M5A88PM-V is used. Searching for that model string on the WWW does not return anything which is unrelated to coreboot, so change that string to M5A88-V. Change-Id: I25cf9d4a5fc3f9b9356e8616452066ebf873f44c Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2613 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com> Reviewed-by: QingPei Wang <wangqingpei@gmail.com>
2013-03-09Add Intel Panther Point USB3 initializationMarc Jones
Add PEI updates and ACPI updates for supporting EHCI to XHCI USB port support. Change-Id: I9ace68a1b3950771aefb96c1319b8899291edd9a Signed-off-by: Marc Jones <marc.jones@se-eng.com> Reviewed-on: http://review.coreboot.org/2519 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-08Persimmon DSDT: Add secondary bus range to PCI0Mike Loptien
Adding the 'WordBusNumber' macro to the PCI0 CRES ResourceTemplate in the Persimmon DSDT. This sets up the bus number for the PCI0 device and the secondary bus number in the CRS method. This change came in response to a 'dmesg' error which states: '[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS' By adding the 'WordBusNumber' macro, ACPI can set up a valid range for the PCIe downstream busses, thereby relieving the Linux kernel from "guessing" the valid range based off _BBN or assuming [0-0xFF]. The Linux kernel code that checks this bus range is in `drivers/acpi/pci_root.c`. PCI busses can have up to 256 secondary busses connected to them via a PCI-PCI bridge. However, these busses do not have to be sequentially numbered, so leaving out a section of the range (eg. allowing [0-0x7F]) will unnecessarily restrict the downstream busses. This change will apply to other AMD mainboards and will be in a different commit. Change-Id: I44f22bc03a0dcbcd2594d4291508826cc2146860 Signed-off-by: Mike Loptien <mike.loptien@se-eng.com> Reviewed-on: http://review.coreboot.org/2592 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-08Eliminate do_div().David Hendricks
This eliminates the use of do_div() in favor of using libgcc functions. This was tested by building and booting on Google Snow (ARMv7) and Qemu (x86). printk()s which use division in vtxprintf() look good. Change-Id: Icad001d84a3c05bfbf77098f3d644816280b4a4d Signed-off-by: Gabe Black <gabeblack@chromium.org> Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2606 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-08AMD Inagua: Use SPD read code from F14 wrapperKimarie Hoot
Changes: - Get rid of the inagua mainboard specific code and use the platform generic function wrapper that was added in change http://review.coreboot.org/#/c/2497/ AMD f14: Add SPD read functions to wrapper code - Move DIMM addresses into devicetree.cb - Add the ASF init that used to be in the SPD read code into mainboard_enable() Notes: - The DIMM reads only happen in romstage, so the function is not available in ramstage. Point the read-SPD callback to a generic function in ramstage. Change-Id: Id05227fcf18c6ab94ffe1beb50b533ab7b0535db Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com> Reviewed-on: http://review.coreboot.org/2607 Reviewed-by: Martin Roth <martin.roth@se-eng.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-08AMD CIMx SB800 boards: platform_cfg.h: Integrate Kconfig SATA Mode choicePaul Menzel
Currently for Advansus A785E-I, ASRock E350M1 and ASUS M5A88-V despite what is chosen in Kconfig »Chipset« menu item, $ more .config […] # CONFIG_ENABLE_IDE_COMBINED_MODE is not set CONFIG_IDE_COMBINED_MODE=0x1 # CONFIG_SB800_SATA_IDE is not set CONFIG_SB800_SATA_AHCI=y # CONFIG_SB800_SATA_RAID is not set CONFIG_SB800_SATA_MODE=0x2 […] the SATA controller is put into IDE mode. $ lspci -nn | grep SATA 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] [1002:4390] (rev 40) Commit »sb800: Add sata ahci/raid mode kconfig option« (d4a0e7d0) [1] added the options above to configure the mode using Kconfig and some SB800 boards were adapted already. For example commit »persimmon: sb800 sata mode configure update« (1386fa74) [2] did so for AMD Persimmon. Doing the same by assigning the Kconfig variable to the value in `platform_cfg.h` integrates this with the three remaining boards listed above. The patch is successfully tested with the ASRock E350M1. $ lspci -nn | grep SATA 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] (rev 40) [1] http://review.coreboot.org/225 [2] http://review.coreboot.org/227 Change-Id: I227257e2c8f04f18c27ff00fe62d42e372de67e4 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2610 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-08AMD Persimmon: mainboard.c: Make comment generic to reduce differencePaul Menzel
Replace »persimmon« by »board« in comment to keep `diff` output between boards small. Change-Id: Ieae2a63782c488ae35f22eb30f5b1049200d12c8 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2611 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-08AMD Union Station: Use SPD read code from F14 wrapperKimarie Hoot
Changes: - Get rid of the union_station mainboard specific code and use the platform generic function wrapper that was added in change http://review.coreboot.org/#/c/2497/ AMD f14: Add SPD read functions to wrapper code - Move DIMM addresses into devicetree.cb - Add the ASF init that used to be in the SPD read code into mainboard_enable() Notes: - The DIMM reads only happen in romstage, so the function is not available in ramstage. Point the read-SPD callback to a generic function in ramstage. Change-Id: I19d6b0d674b67294519383f80928471b37da1e14 Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com> Reviewed-on: http://review.coreboot.org/2609 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-08AMD South Station: Use SPD read code from F14 wrapperKimarie Hoot
Changes: - Get rid of the south_station mainboard specific code and use the platform generic function wrapper that was added in change http://review.coreboot.org/#/c/2497/ AMD f14: Add SPD read functions to wrapper code - Move DIMM addresses into devicetree.cb - Add the ASF init that used to be in the SPD read code into mainboard_enable() Notes: - The DIMM reads only happen in romstage, so the function is not available in ramstage. Point the read-SPD callback to a generic function in ramstage. Change-Id: If4291d25ea81bf375f55b64c07c223a847a211d0 Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com> Reviewed-on: http://review.coreboot.org/2608 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-08ARMV7 and Google/Snow: Add exception support code to the ramstageRonald G. Minnich
This is previously used exception code from libpayload. On startup it installs and then tests an exception handler. The test is an unaligned memory operation. Yes, we've seen what might be exceptions in the ramstage, and it makes sense to handle them. This code is identical in structure and operation to the previously committed payload exception handler, though we reserve the right to change it as circumstances require. The remaining question is whether we need it in romstage. Change-Id: I24484686c33c9757af8ba171ebae9773828fb69d Signed-off-by: Gabe Black <gabeblack@google.com> Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-on: http://review.coreboot.org/2614 Tested-by: build bot (Jenkins) Reviewed-by: David Hendricks <dhendrix@chromium.org>
2013-03-08AGESA: Fix CR0_PE bit defineKonstantin Aladyshev
AGESA code has wrong definition of CR0_PE bit (1 instead of 0). PE [Protected Mode Enable] is 0 bit in CR0 register (If PE=1, system is in protected mode, else system is in real mode) Bit 1 is MP [Monitor co-processor] (Controls interaction of WAIT/FWAIT instructions with TS flag in CR0) System uses CR0_PE define, but I didn't expect any consequences because of this bug. Change-Id: I54d9a8c0ee3af0a2e0267777036f227a9e05f3e1 Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/2591 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-08Supermicro H8QGI: set up right frequency limits for memory controllerKonstantin Aladyshev
According to BKDG: "Memory controller (MCT) and DRAM controllers (DCTs) additions: • Support for 933 MHz (1866 MT/s) MEMCLK frequency." Change-Id: I6f307ce3fcb355d5445f1ea86def73a41b928a57 Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/2589 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-08AGESA: Fix bug in AMD_DISABLE_STACK_FAMILY_HOOK_F15Konstantin Aladyshev
_RDMSR instruction loads the contents of a 64-bit model specific register (MSR) specified in the ECX register into registers EDX:EAX. The EDX register is loaded with the high-order 32 bits of the MSR and the EAX register is loaded with the low-order 32 bits. EDX:EAX = MSR[ECX] So bit 49 will be contained in EDX register. Buggy code instead of bit 49 (CombineCr0Cd) sets bit [49-32=17] (PfcStrideDis). PfcStrideDis bit disables stride prefetch generation. This leads to memory bandwidth loss. _________ Supermicro H8QGI board After applying this change i observed huge memory bandwidth increase in tests that runs on small amount of cores. But unfortunately it doesn't affect overall bandwidth results on 4P system with 48 cores. So i think that in this system leading limiting factor is AMD HT-ASSIST feature (Probe filter). But right now it is not working. System stucks in Linux boot. I have done some experiments and figured out that stuck happens when system have cores in compute unit (CU) other than CU with BSC (boot strap core). CU is two cores (primary and seconary) that shares some things (L2 cache, FPU ...) So with probe filter i can boot Linux with one (BSC) or two (BSC + secondary core in its CU) cores. And with this configuration i can see memory bandwidth on 1 core (or two cores) close to original bios. Change-Id: I5a95f5b753d600c70d3c93d36fecc687610c61cd Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/2588 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-08FrontRunner/Toucan-AF: lower SPI speed to 22 MHzJens Rottmann
The Hudson-E1's default SPI speed for normal i.e. non-fast reads is 66 MHz, but the SST 25VF032B datasheet allows max. 25. Lower the speed to 22 MHz, otherwise BIOS flashing fails. Change-Id: I22e87d833a3ebd316b6e873595a2480831533ab1 Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de> Reviewed-on: http://review.coreboot.org/2605 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-07AMD Persimmon: Use SPD read code from F14 wrapperMartin Roth
Changes: - Get rid of the persimmon mainboard specific code which has been moved into the wrapper as a platform generic function in change http://review.coreboot.org/#/c/2497/ AMD f14: Add SPD read functions to wrapper code - Move DIMM addresses into devicetree.cb - Add the ASF init that used to be in the SPD read code into mainboard_enable() Notes: - The DIMM reads only happen in romstage, so the function is not available in ramstage. Point the read-SPD callback to a generic function in ramstage. Change-Id: I5f017dbb8dee5a09ec19734a6069ff9b71a6ab50 Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/2500 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-07AMD Fam14: Add SPD read functions to wrapper codeMartin Roth
Change: This is the initial step for moving the AMD F14 & HUDSON1,2,3 SPD-read callout out of the mainboard directories and into the wrapper. The next step is to update the platforms to use this routine in BiosCallouts.c and to delete the code from the mainboard directories. The DIMM addresses should be moved into devicetree.cb. If there are significant differences or reasons that the mainboard needs to override this code, it's perfectly reasonable to keep using the version in the mainboard, but this allows us to remove duplicated code and simplify the mainboard directories. Notes: This started by duplicating what was in Persimmon, and was changed to use the devicetree.cb structures. The ASF setup was also removed from the persimmon copy (PMIO writes to 0x28 & 0x29) as that's not needed for the SPD access and doesn't make sense to initialize here. Significant cleanup and magic number reduction was done as well. It is intended that this file will not be included in ramstage as the DIMM init is all done in romstage. This is similar to what was done for Parmer/Thatcher in commit 7fb692bd - http://review.coreboot.org/#/c/2190/ Fam15tn: Move SPD read from mainboards into wrapper Yes, it would make sense to split this into two separate files and move the SMBUS initialization and access into the southbridge wrapper. Maybe that can come next. Change-Id: I1e106d3912c160b0015bf02158d9faba4f578ee3 Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/2497 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-07Remove UTF-8 characters from commentsRonald G. Minnich
I've used an operating system for over 10 years now that makes UTF-8 easy. It's not called Linux or OSX. When UTF-8 is needed, of course, then we can look again. I can't think of a single redeeming feature of placing it in the comment in this manner. It's certainy not needed. The inclusion of UTF-8 characters is inconvenient, especially from a text terminal. I don't really want to start using compose in CROSH shell terminals on chromeos. We might want to incorporate "no UTF-8" as a commit filter. For now, get rid of these characters. Change-Id: If94cc657bae1dbd282bec8de6c5309b1f8da5659 Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-on: http://review.coreboot.org/2604 Reviewed-by: Bernhard Urban <lewurm@gmail.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-07Revert "ARMv7: Simplify div64"David Hendricks
This reverts commit 1cd616082100f47dc2d6d73669c6aa2e5eb039ad Division bites us again. I don't know how or why, but printk() seems to break (again) with this patch. I'm surprised we didn't encounter problems earlier on... Change-Id: I81cb9f20879f5eb73a76e1af47b96a68d1e81dc8 TODO: Find a better solution for div64. This one is too painful, but seems necessary for now (and sort-of works with our vtxprintf hack). Reviewed-on: http://review.coreboot.org/2600 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-07snow: add real values for GPIOs in fill_lb_gpios()David Hendricks
This adds some real GPIO mappings where virtual GPIOs were used before. Change-Id: I25d4be45f986c8d622b97151f8bdae2651baf3e6 Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2603 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-07exynos5: add GPIO port enumsDavid Hendricks
This adds an enum for GPIO ports on the Exynos5. To make them useful, they are assigned the absolute MMIO address where a s5p_gpio_bank struct can point to. Change-Id: Ia539ba52d7393501d434ba8fecde01da37b0d8aa Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2602 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-07google/snow: fix coding styleStefan Reinauer
cosmetics Change-Id: Iea33768d901641861aa7b2c76af8753a848f584d Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/2601 Tested-by: build bot (Jenkins) Reviewed-by: David Hendricks <dhendrix@chromium.org>
2013-03-07src/arch/x86/boot/acpigen.c: Small coding style and comment fixesPaul Menzel
While reading through the file fix some spotted errors like indentation, locution(?), capitalization and missing full stops. Change-Id: Id435b4750e329b06a9b36c1df2c39d2038a09b18 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2484 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-07Fix build by adding `cbmem.c` to `COLLECT_TIMESTAMPS`Kyösti Mälkki
A board without HAVE_ACPI_RESUME did not build with COLLECT_TIMESTAMPS enabled as `cbmem.c` was not built. Change-Id: I9c8b575d445ac566a2ec533d73080bcccc3dfbca Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/2549 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-07Intel e7505: provide get_top_of_ramKyösti Mälkki
This is required to enable EARLY_CBMEM_INIT. Change-Id: I6d8caf382aa48eded81c1e94bbbcd3975ea88a1a Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/2550 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-03-07Fix socket LGA775Kyösti Mälkki
Models 6ex and 6fx select UDELAY_LAPIC so cannot select contradicting UDELAY_TSC here. Model 1067x requires speedstep. Change-Id: I69d3ec8085912dfbe5fe31c81fa0a437228fa48f Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/2525 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-27 03:56:52 +0000