summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-10-16sb/intel/bd82x6x/lpc: Set up default LPC decode rangesArthur Heymans
This sets up some common default LPC decode ranges in a common place. This may set up more decode ranges than needed but that typically does not hurt. Mainboards needing additional ranges can do so in the mainboard pch_enable_lpc hook. Change-Id: Ifeb5a862e56f415aa847d0118a33a31537ab8037 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33549 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-16intel/broadwell: Hook libgfxinit upNico Huber
As VGA_ROM_RUN and libgfxinit are mutually exclusive in Kconfig, we don't have to guard all the VGA BIOS if's and can assume gfx_get_init_done() returns 0 until all the quirks are handled. Then, we can run libgfxinit. Change-Id: Id5d0c2c12b1ff8f95ba4e0223a3e9aff27547acd Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/20100 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2019-10-16intel/broadwell: Implement proper backlight PWM configNico Huber
Port the backlight-PWM handling from Skylake instead of the previously used Haswell version. We use a 200Hz PWM signal for all boards. Which is higher than the previous devicetree value, 183Hz, but that was over- ridden by the VBIOS anyway. 200Hz is still very low, considering LED backlights, but accurate values are unknown at this time. Lynx Point, the PCH for Haswell and Broadwell, is a transition point for the backlight-PWM config. On platforms with a PCH, we have: o Before Lynx Point: The CPU has no PWM pin and sends the PWM duty-cycle setting to the PCH. The PCH can choose to ignore that and use its own setting (BLM_PCH_OVERRIDE_ENABLE). We use the CPU setting on these platforms. o Lynx Point + Haswell: The CPU has an additional PWM pin but can be set up to send its setting to the PCH as before. The PCH can still choose to ignore that. We use the CPU setting with Haswell. o Lynx Point + Broadwell: The CPU can't send its setting to the PCH anymore. BLM_PCH_ OVERRIDE_ENABLE must always be set(!) if the PCH PWM pin is used (it virtually always is). We have to use the PCH setting in this case. o After Lynx Point: Same as with Broadwell, only BLM_PCH_OVERRIDE_ENABLE is implied and the bit not implemented anymore. Change-Id: I1d61d9b3f1802ebe18799fc4d06f1f1d3b54c924 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35897 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2019-10-16mb/lenovo/x201: Fix Linux shutting down on s3 resumeArthur Heymans
On some configuration coreboot boots too fast and the EC reports the max temperature, resulting in Linux shutting down immediately. Change-Id: I610c7c9fbf2130566d3c2c758f1796314d3a0973 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36059 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
2019-10-16src/superio: Remove unused 'include <console/console.h>'Elyes HAOUAS
Change-Id: Iaeb69c5e7cb3345f4f2ff90eef4f97d72c722ca2 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36048 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-16src/mb: Remove unused 'include <arch/io.h>'Elyes HAOUAS
Change-Id: I03461cb9e87b4ddd599e5601637a75b012694e7c Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36047 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-16src/superio: Remove unused 'include <arch/io.h>'Elyes HAOUAS
Change-Id: Ia08e27da51f1f523232379960dc21c1ba4849932 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36046 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-16postcar: Fix linking error with disabled postcar consolePatrick Rudolph
Link files to provide snprintf used by VBOOT code. Change-Id: I040c3952c22893da5aae11b20a618aa4006c6c58 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36053 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2019-10-16util/ifdtool: Fix argument parsing for layout/validateSamuel Holland
When `mode_validate` was added, a second copy of `mode_layout` was accidentally added to the multiple-mode-argument check instead. This prevents `-f` from working. Fix the check to reference the correct variable. Change-Id: Ibac6f090550ff63ec9158355b0450da204a300a7 Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36049 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-10-16drivers/usb: Enable EHCI debug during verstageArthur Heymans
Change-Id: I14843c1944f2c1e0a26870b576bac549c0cac7f9 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36040 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-10-16vboot: add new vb2ex_abort callbackJoel Kitching
Required for new VB2_ASSERT and VB2_DIE macros in vboot code. (See chromium:972956.) BUG=b:124141368, chromium:1005700 TEST=make clean && make test-abuild BRANCH=none Change-Id: I61a1036ccab80862d6eb12f9f72286f29e8478cf Signed-off-by: Joel Kitching <kitching@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36035 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-10-16util/amdfwtool: Grow the Embedded Firmware StructureMarshall Dawson
Ensure adequate space exists for all Embedded Firmware Structure fields. Field definitions are NDA only. See PID #55758 "AMD Platform Security Processor BIOS Architecture Design Guide for AMD Family 17h Processors". BUG=b:141790457 TEST=run on Mandolin Change-Id: I098ffc7c05d27387a877e6b7c8628d98939bd9af Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35667 Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Justin Frodsham <justin.frodsham@amd.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-15helios: Add TEMP_SENSOR4 to DPTFPaul Fagerburg
Helios adds TEMP_SENSOR4 to the EC ADC2 pin. Add this to the DPTF. BRANCH=None BUG=b:142266102 TEST=`emerge-hatch coreboot` Verify that Helios builds correctly. Change-Id: I3bc19f9b9bd644e134987749ad9a4d875ad8b40a Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35920 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com>
2019-10-15mb/google/hatch: set wifi sar for dragonairWisley Chen
Enable wifi sar feature and set wifi sar name for dragonair sku. BUG=b:142109545 TEST=emerge-hatch coreboot chromeos-bootimage 1. Check wifi_sar-dragonair.hex in /cbfs-rw-raw/dratini 2. Add iwlwifi.debug into kernel params. 3. check SAR value from dmesg only when sku id is 21/22 Change-Id: I0e08610b7c7d2d8da5a749d278bcde26af590e31 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35807 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2019-10-15mb/google/hatch: Initialize FPMCU_PCH_BOOT1Wisley Chen
FPMCU_PCH_BOOT1 pin is connected to GPP_C12. So, config GPP_C12. BUG=b:142188003 TEST=emerge-hatch coreboot Change-Id: I73a5c3529330ef3e72f4c7d5fcbbd2f6693494d8 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35845 Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-15soc/intel/skylake/chip: Unhide P2SB devicePatrick Rudolph
APL unhides the P2SB device in coreboot already. Do the same on SKL/KBL. As the coreboot PCI allocator needs to be able to find the device, unhide it after FSP-S. The device is hidden in the SoC finalize function already and not visible in the OS, as more P2SB device IDs have been added. Other SoCs aren't updated, because they are too broken. Fixes "BUG: XXX requests hidden ...." warnings in coreboot log. Tested on Supermicro X11SSH-TF. Change-Id: I0d14646098c34d3bf5cd49c35dcfcdce2c57431d Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35620 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Michael Niewöhner
2019-10-15soc/intel/common/block/sgx: Fix crash in MP initPatrick Rudolph
On Hyper-Threading enabled platforms the MSR_PRMRR_PHYS_MASK was written when already locked by the sibling thread. In addition it loads microcode updates on all threads. To prevent such race conditions only call the code on one thread, such that the MSRs are only written once per core and the microcode is only loaded once for each core. Also add comments that describe the scope of the MSR that is being written to and mention the Intel documents used for reference. Fixes crash in SGX MP init. Tested on Supermicro X11SSH-TF. Change-Id: I7102da028a449c60ca700b3f9ccda9017aa6d6b5 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35312 Reviewed-by: Christian Walter <christian.walter@9elements.com> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-15mainboard/lenovo/t410: Add new portNicolas Reinecke
The port is based on the x201 / t410s. 2537-vg5 / i5, no discrete gpu Tested and working: * Native raminit * Native gfxinit * Booting Seabios 1.12.1 * Booting from EHCI * Running GNU/Linux 5.0.0 * No errors in dmesg * EHCI debug on the devices left side, bottom-right * Keyboard * Fn keys (Mute, Volume, Mic) * Touchpad * TPM * Wifi * Sound * USB * Ethernet * S3 resume * VBOOT Testing in progress. Untested: * VGA * Displayport * Docking station Bugs: * AC adapter can't be read from ACPI * TPM not working with VBOOT and C_ENV BB Details for flashing externally: 1. Disconnect all power 2. Connect the external flasher 3. Connect the power cord (This fixes internal power control) 4. Remove the power cord Change-Id: Id9d872e643dd242e925bfb46d18076e6ad100995 Signed-off-by: Nicolas Reinecke <nr@das-labor.org> Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/11791 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2019-10-14Documentation/gfx: Update support list of libgfxinitNico Huber
Also get rid of some manual hyphenation. Change-Id: Ibeb4eceeae48cf375171d0261ed9475010b0d5b1 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35989 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2019-10-14nb/intel/gm45: Don't run graphics init on s3 resumeArthur Heymans
This assumes ACPI aware OS also have a driver for this particular hardware, which is the case for at least Linux. This saves ~60ms on S3 resume. Change-Id: I2dcd399fee8e2d1cd1b70e60e1669a49c7aa8cb4 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35995 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-10-14sb/intel/i82801ix: Add common code to set up LPC IO decode rangesArthur Heymans
This does the following: - Add gen[1-4]_dec options to the devicetree to set up generic LPC decode ranges in the southbridge code. - Move setting up some default decode ranges to a common place. If somehow a board needs to override this behavior it can happen in the mb_setup_superio() hook (that will be renamed when moving to C_ENVIRONMENT_BOOTBLOCK). Change-Id: I3d904b1125bc410c11aa73a89b1969284e88dac1 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35991 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-10-13src/superio: Remove unused superio chipsMartin Roth
These SIOs are not being used or tested by abuild, so remove them from the tree. The only 3 currently unused SIOs that don't get removed here have board ports in review. src/superio/fintek/f71805f src/superio/fintek/f71872 src/superio/intel/i8900 src/superio/ite/it8671f src/superio/ite/it8716f src/superio/nsc/pc87309 src/superio/nsc/pc87360 src/superio/nsc/pc87366 src/superio/nsc/pc97317 src/superio/smsc/dme1737 src/superio/smsc/lpc47b272 src/superio/smsc/lpc47b397 src/superio/smsc/sch4037 src/superio/smsc/sio1036 src/superio/via/vt1211 src/superio/winbond/w83697hf src/superio/winbond/wpcd376i Signed-off-by: Martin Roth <martin@coreboot.org> Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: I61d486d2c1e2b85eb292eaa78316c36e1735ebf4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/35428 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-10-13superio/common: Remove unused include 'pnp_def.h'Elyes HAOUAS
Change-Id: I2d0b3d73d646fc43f2562aa5af2358398eaf28b0 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35987 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-13mb/hp/z220_sff_workstation: Remove unused include 'pnp_def.h'Elyes HAOUAS
Change-Id: Id8e25caf2868c37c9d7c7717dd908152dfc583a3 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35986 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-13nb/intel/nehalem: Start VBOOT in bootblock with a separate verstageArthur Heymans
Tested on Lenovo Thinkpad X201, selects slot or recovery just fine. Change-Id: Ia2b2f2b95510388599266264eaed0d64ce9b6ec5 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35952 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-10-13nb/intel/nehalem: Move to C_ENVIRONMENT_BOOTBLOCKArthur Heymans
A few notable changes: - Microcode init is done in assembly during the CAR init. - The DCACHE_BSP_STACK_SIZE is set to 0x2000, which is the same size against which the romstage stack guards protected. - The romstage mainboard_lpc_init() hook is removed in favor of the existing bootblock_mainboard_early_init(). Change-Id: Iccd7ceaa35db49e170bfb901bbff1c1a11223c63 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35951 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-10-13sb/intel/ibexpeak: Move some early PCH init after console initArthur Heymans
Some of the initialization isn't necessary before console INIT is done. EHCI debug still works fine on the Lenovo Thinkpad X201. Change-Id: I0c33efd98844f7188e0258cf9f90049d45145e7c Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35949 Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-12ec/acpi/ec.c Link EC code in bootblock & verstageArthur Heymans
This allows to read and set bits in the EC ram in the bootblock or verstage. This can be useful if one needs to read a keyboard key as an input for get_recovery_mode_switch in vboot. Change-Id: I20b2264012b2a364a4157d85bfe5a2303cc5e677 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35950 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-10-12util/inteltool: remove unsupported MSRs for 06_9EHMaxim Polyakov
Change-Id: I5c1e4d20efa7630bf4e6210591790055ead0161c Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35916 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-12util/inteltool: fix 6d0H-6dfH MSR names for 06_9EHMaxim Polyakov
Change-Id: I92e8f5194114f7756e3858ff13c207daebe8167c Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35915 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-12util/inteltool/cpu: fix IA32_PLATFORM_ID MSR addrMaxim Polyakov
According to the documentation [1], IA32_PLATFORM_ID MSR register address should be 17H. [1] Table 2-2. Intel (R) 64 and IA-32 Architectures Software Developer’s Manual. Volume 4: Model-Specific Registers. May 2019. Order Number: 335592-070US Change-Id: I9a16b162db51d21c7849b3c08c987ab341845b1e Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35913 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-12util/inteltool: remove duplicate MSR for 06_9EHMaxim Polyakov
Change-Id: I34981a69ad027444bc757449db2366f51c13f0e3 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35914 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-12mb/biostar/am1ml: Use ite's common functionsElyes HAOUAS
Change-Id: I0b1356420c9ae419b2a0a247b9dc6c8e92b7689a Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35966 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-12mb/roda/rk886ex: Use pnp_write_config functionElyes HAOUAS
Change-Id: Ic56367d64b9304b36f5ba5a4b7d5237574eb73ae Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35965 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-12mb/getac/p470: Use pnp_write_config functionElyes HAOUAS
Change-Id: Iaf9a4608f1b7d25cf5d8dbe2c1489b3d2d00f25a Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35964 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-11mb/{razer,purism}: Don't select NO_POSTNico Huber
The NO_POST option covers more than classical port 80 output, hence selecting it seems wrong in any case. The default is still rather user patronizing, but let's keep it. As a side effect, this fixes the ability to override the default for NO_POST which Kconfig rejected while these boards selected it. (Seems like a bug in Kconfig, though.) Change-Id: I896b08812b1aa6ce249d7acc8073ebcc0f72eace Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35956 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
2019-10-11sb/intel/i82801gx: Move CIR init to a common placeArthur Heymans
Some boards with the G41 chipset lacked programming CIR, so this change add that to those boards too. Change-Id: Ia10c050785170fc743f7aef918f4849dbdd6840e Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35795 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2019-10-11vendorcode/eltan/Kconfig: Hide the Kconfig options when lacking supportArthur Heymans
The vendorcode/eltan mboot and verified boot options only build if a few other Kconfig options are defined. Change-Id: Ie333d2fbf294e23ec01df06ee551e2d09541c744 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35954 Reviewed-by: Wim Vervoorn Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com> Reviewed-by: Frans Hendriks <fhendriks@eltan.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-11vendorcode/siemens: Remove sourcing non existing Kconfig filesArthur Heymans
There is only one subdir in vendorcode/siemens and it does not feature a Kconfig file. Change-Id: I136743344465cea9c769234aa84d9ebe874ef0d2 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35953 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2019-10-11mb/google/hatch: Add new touchscreen option for KohakuTim Wawrzynczak
The next board rev will have a new option for an Elan touchscreen. Add support for this in the devicetree, as well as use the 'probed' property on both touchscreen options. BUG=b:141957731 BRANCH=none TEST=compiles (next board rev not available yet) Change-Id: I135e693304cbb8dffc0caf4c07846033d6802208 Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35944 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Shelley Chen <shchen@google.com>
2019-10-10mb/google/octopus/variants/fleex: Update GPIOs to fix EMRJohn Su
Update GPIO_138 and GPIO_139 setting to fix EMR function. BUG=b:141729962,b:141281846 BRANCH=octopus TEST=verify EMR function in Grob360S. Change-Id: I28cef592374fb4aeee2f3d3010cc0e237d62a2fd Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35881 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-10-10nb/intel/pineview/Kconfig: Remove romcc leftoverArthur Heymans
This is unused since C_ENVIRONMENT_BOOTBLOCK is used. Change-Id: Id5af41e455d211eba89cfeb625f4c728b4145da7 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35948 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-10-10soc/intel: sgx: get rid of UEFI-style usage of global variableMichael Niewöhner
Rework SGX enable status in a clean way without using a global variable. Change-Id: Ida6458eb46708df8fd238122aed41b57ca48c15b Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35882 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-10-10mb/{ibase/mb899,kontron/986lcd-m}: Use pnp_write_hwm5_index functionElyes HAOUAS
Change-Id: If30a17d053da8f0758085fc36469b564d46049cd Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35901 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-09soc/qualcomm: Remove default ops to generate bootblock.binArthur Heymans
This is done by default in the main Makefile.inc. TEST: With BUILD_TIMELESS=1 the resulting binary is identical before and after the change. Change-Id: Ie85e023df1f1c2b0f115e4f92719a511f60019c3 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35899 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-10-09soc/mediatek/mt8183: Change argument type of mt_set_emiYu-Ping Wu
Since struct dramc_param has been defined, we can pass the struct directly from mt_mem_init(). BUG=b:139099592 BRANCH=none TEST=emerge-kukui coreboot Change-Id: If7333fb579eff76dd9d1c2bf6fdfe7eccb22050f Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35846 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-09soc/mediatek/mt8183: Run DRAM full calibrationHuayang Duan
Load the calibration params from flash first and check the correctness of the params. If the params have correct format, perform DRAM fast calibration with these params to reduce bootup time. Otherwise, load the DRAM blob and perform DRAM full calibration. Bootup time of DRAM partial calibration: - 1,349,385 usecs with low frequency - 924,698 usecs with middle frequency - 1,270,089 usecs with high frequency 3,544,172 usecs in total. Bootup time of DRAM fast calibration: - 216,663 usecs with low frequency - 328,220 usecs with middle frequency - 322,612 usecs with high frequency 867,495 usecs in total. BUG=b:139099592 BRANCH=none TEST=emerge-kukui coreboot Change-Id: I8de29b14b1fb24b3b4f351c855c5c4d8f350cc34 Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35110 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-09soc/mediatek/mt8183: Use cached calibration result for faster bootupHuayang Duan
Load calibration params from flash. If the format of the params is correct, use these calibration params for fast calibration to reduce the bootup time. Bootup time of DRAM partial calibration: - 1,349,385 usecs with low frequency - 924,698 usecs with middle frequency - 1,270,089 usecs with high frequency 3,544,172 usecs in total. Bootup time of DRAM fast calibration: - 216,663 usecs with low frequency - 328,220 usecs with middle frequency - 322,612 usecs with high frequency 867,495 usecs in total. BUG=b:139099592 BRANCH=none TEST=Boots correctly on Kukui Change-Id: I9ef4265dd369a1c276bb02294696556df927e7bc Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35164 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-09soc/mediatek/mt8183: Add the shared 'dramc_param' moduleYu-Ping Wu
The dramc_param module simplifies the communication between coreboot and MTK DRAM full calibration blob, and is shared by both implementations to ensure the same format of parameters. BUG=b:139099592 BRANCH=none TEST=emerge-kukui coreboot Change-Id: I4cfd634da1855a76706aab0b050197251e2ed4dd Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35775 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-09soc/mediatek/mt8183: Simplify usage of dramc_engine2_endYu-Ping Wu
Since we always write to &ch[chn].ao.dummy_rd after calling dramc_engine2_end(), this write could be merged into dramc_engine2_end() to simplify code. BUG=none BRANCH=none TEST=emerge-kukui coreboot Change-Id: Ibb4bd5ed016118811ad2097098417c19f00f4263 Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35749 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-17 00:02:18 +0000