summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-12-04ec/google/wilco: Enable COM1 ACPI deviceDuncan Laurie
Enable the COM1 ACPI device based on the existing Kconfig option CONFIG_DRIVERS_UART_8250IO instead of expecting the mainboard to also define another value for ACPI. Change-Id: I69361cc2c245cfcad3e4f57567bf56d5a26f0b06 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/c/29672 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-04mb/google/sarien: Enable WWAN detectionAmanda Huang
Set WWAN_GPIO_PERST#(GPP_D22) to low at bootblock stage to meet the logic output for WWAN_PERST#_R to high. BUG=120004153 TEST=Boot up Sarien board, check WWAN get detected as USB devices through lsusb. Change-Id: I16f1101c64dfd4dcb5e8342fdb925951f6f2f90b Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/30017 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-12-04soc/sifive/fu540: Load PLL settings from a structJonathan Neuschäfer
The different PLLs in the fu540 use the same register layout, so use one function (configure_pll) to program a PLL and wait for it to lock. This also makes it possible to dynamically calculate the PLL settings later. TEST=Boot until "Payload not loaded" on HiFive Unleashed Change-Id: I5c0cee886bad5758c70f967d2bb998c1e1a736ab Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/c/29356 Reviewed-by: Philipp Hug <philipp@hug.cx> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-04drivers/intel/fsp1_1/romstage.c: Fix typoFrans Hendriks
Correct typo of 'Initialize' BUG=N/A TEST=N/A Change-Id: I94cfd9c41bb5f9751ef4a18beaeba05108220bc8 Signed-off-by: Frans Hendriks <fhendriks@eltan.com> Reviewed-on: https://review.coreboot.org/c/30016 Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-04mb/opencellular/elgon: Enable write protectionPatrick Rudolph
* Verify the flash write protection on each boot * Program non-volatile write protection on first boot Tested using I715791b8ae5d1db1ef587321ae5c9daa10eb7dbc. The bootblock is write-protected as long as the #WP pin is asserted low: * Reprogramming of the status register fails. * Trying to write to WP_RO region fails. Programming the WP_RO is only possible if #WP pin is high. Change-Id: I6a940c69ecb1dfd9704b2101c263570bebc5540e Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/29532 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
2018-12-04drivers/spi/winbond: Fix TB bitPatrick Rudolph
The TB has to be inverted to actually protected the correct region. Tested on elgon using I67eb4ee8e0ad297a8d1984d55102146688c291fc. Change-Id: I715791b8ae5d1db1ef587321ae5c9daa10eb7dbc Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/30014 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Reviewed-by: David Hendricks <david.hendricks@gmail.com> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-12-04mb/google/poppy/variants/nami: update bard/ekko sku idsRen Kuo
update the new sku ids of bard/ekko BUG=b:120257865 BRANCH=Nami TEST=emerge-nami coreboot chromeos-bootimage write the new sku id in cbi and verify the fw to check it can get the correct settings by the sku id Change-Id: I3579d3d8042a270d8ea8e2f7b5612ff8e2cdfa7b Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/30031 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03mb/google/octopus: Enable mode change as wake source from S3/S0ixFurquan Shaikh
This change enables mode change as a wake source from S3 and S0ix. Thus, any time the device switches between clamshell and tablet mode while it is suspended, it will be treated as a valid user event and hence wake source. BUG=b:120349473 BRANCH=octopus TEST=Verified that octopus wakes up on mode transitions. Change-Id: Ib224df434730f873ce5514303e5d043cbc85a9a4 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/30001 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2018-12-03soc/intel/apl: Enable graphics with libgfxinitNico Huber
Backlight control of internal panels likely won't work as configuration for that seems absent in coreboot. Also, libgfxinit doesn't support any MIPI/DSI connections, yet, and neither Gemini Lake. TEST=Booted work-in-progress port kontron/mal10 with VGA text and linear framebuffer modes. DP display came up. Change-Id: I7b111f1cdac4d18f2fc3089f57aebf3ad1739e5d Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/c/29903 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03cpu/intel/fsp_model_406dx: Drop dead microcode referenceNico Huber
The referenced Kconfig symbols don't exist (anymore?). Change-Id: Ia724262a526fe960c17ae4b248acfa42fc342331 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/c/29931 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: David Guckian Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2018-12-03sb/intel/i82801jx: Fix the x_pm2_cnt_blk addrlArthur Heymans
Removes a warning in Linux about FACP. Change-Id: Ia12302a4dcd34eacdcc8ae16bd39e951e616c6ea Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/30011 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-12-03soc/intel/apollolake: Add support to print ME versionFurquan Shaikh
This change adds support to print ME version if UART_DEBUG is enabled. Check for UART_DEBUG is necessary because talking to ME to get the firmware version adds ~0.6 seconds to boot time. TEST=Verified on octopus that ME version printed is correct. Change-Id: I41217371558da1af694a2705e005429155d62838 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/29989 Reviewed-by: Justin TerAvest <teravest@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03smmstore: update smm store filename to use an underscoreJoel Kitching
Rename "smm store" to "smm_store". BUG=b:120060878 TEST=None Signed-off-by: Joel Kitching <kitching@google.com> Change-Id: If70772e17cc1668a28b376eeccfde0424e637b1a Reviewed-on: https://review.coreboot.org/c/29854 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-12-03soc/amd/stoneyridge: Use new ACPI MMIO functionsRichard Spiegel
Replace IO access to ACPI registers with the new MMIO access functions. BUG=b:118049037 TEST=Build and boot grunt. Test ACPI related functionality. Change-Id: I7544169bb21982fcf7b1c07ab7c19c6f5e65ad56 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/c/29296 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2018-12-03soc/amd/stoneyridge: Create MMIO offsets for ACPIRichard Spiegel
ACPI registers can be accessed through IO or through MMIO. However, the offset relationship is not one to one. Therefore, definitions with the correct offset for MMIO access are needed. BUG=b:118049037 TEST=Use Chrome OS IOTOOLS io_readxx and mem_readxx to find the correct relationship between ACPI IO and ACPI MMIO. Change-Id: Id20754c0fc0af35bc9eb1a4b40c62fbf9ed6304d Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/c/29294 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2018-12-03mb/asus/am1i-a: add missing GPIO IO portsKevin Cody-Little
This makes the mainboard able to boot again. Change-Id: Id96fbfd5c815431dba2f030fca62a5ea16b97393 Signed-off-by: Kevin Cody-Little <kcodyjr@gmail.com> Reviewed-on: https://review.coreboot.org/c/29994 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03MAINTAINERS: Add myself as some mainboards' maintainerAngel Pons
Add myself as a maintainer of the four mainboards I ported. For those which were added as a variant, add myself as a maintainer of the whole mainboard group. Change-Id: I0e1b54279027fae82ea9f2825e6f27d38ef3c746 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/29995 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-12-03mb/sifive/hifive-unleashed: Use if (IS_ENABLED(...))Jonathan Neuschäfer
"if" is preferable over "#if", because it lets the compiler perform syntax and type checks even if CONFIG_CONSOLE_SERIAL is disabled. Change-Id: I45a763f2d854fbe9082795bc74de7a9d0fded3c9 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/c/29336 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Philipp Hug <philipp@hug.cx> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2018-12-03soc/sifive/fu540: Simplify UART refclk calculationJonathan Neuschäfer
clock_get_coreclk_khz() already detects whether the PLL or the input clock (hfclk) is used. Tested on HiFive Unleashed. Change-Id: I264977b0de0b81ef74a014984b6d33638ab33f4b Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/c/29334 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Philipp Hug <philipp@hug.cx> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-12-03MAINTAINERS: Add Philipp Hug as reviewer for RISC-VJonathan Neuschäfer
Philipp has been reviewing and writing RISC-V-related code for a while. Change-Id: I3f2d3a61f66343a6e0350909edfe466d2ee6c089 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/c/29980 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Reviewed-by: Philipp Hug <philipp@hug.cx>
2018-12-03sb/intel/lynxpoint: Move `HAVE_SMI_HANDLER` to southbridge KconfigTristan Corrick
All Lynx Point board select this, and none build without it. Change-Id: I4b59b10ee985cff5a8e1442677d36b0be88cf437 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/c/29992 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-12-03sb/intel/common: Create a common PCH finalise implementationTristan Corrick
The common finalise code is used by bd82x6x, Lynx Point, and Ibex Peak. Lynx Point now benefits from being able to write-protect the flash chip. For Lynx Point, writing the SPI OPMENU now happens in ramstage, as done in bd82x6x. Tested on an ASRock H81M-HDS (Lynx Point). When write-protection is configured, flashrom reports all flash regions as read-only, and does not manage to alter the contents of the flash chip. Also tested on an ASUS P8H61-M LX (Cougar Point). Everything seems to work as before. Change-Id: I781082b1ed507b00815d1e85aec3e56ae5a4bef2 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/c/29977 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-12-03sb/intel/lynxpoint: Ensure the finalise handler is calledTristan Corrick
The finalise handler is not called during S3 resume when using the `BS_PAYLOAD_BOOT` approach. So, adopt the `lpc_final` approach used by bd82x6x and others. Tested on an ASRock H81M-HDS. The finalise handler is now called on the normal boot path, and during S3 resume. Change-Id: I9766a8dcbcb38420e937c810d252fef071851e92 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/c/29976 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-12-03sb/intel/lynxpoint: Make the finalise handler commonTristan Corrick
The ASRock H81M-HDS doesn't implement a finalise handler. To fix this, and reduce code duplication in the process, make a common implementation. There should be no functional change to boards with existing finalise handlers, since the code is identical among them and the new, common implementation. Tested on an ASRock H81M-HDS. The finalise handler works. Change-Id: I13b581a2219288019a4e0c9e618db3ac7c3c15ab Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/c/29975 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-12-03mb/google/poppy/variant/nocturne: increase touch panel power-on delayNick Vaccaro
The WACOM 5C01 touch panel power-up delay of 10mS is too aggressive and causes "failed to change power setting" errors in the kernel, so this change increases the power-up delay to 20mS which allows enough time for the WACOM device's i2c controller to wake up. BUG=b:120090384 BRANCH=none TEST=flash and boot nocturne, log into kernel, execute the following command and make sure the string is not found : dmesg | grep "failed to change power setting" Change-Id: I1db0b3f5ce666b79d8ada2939ec865233ce52a56 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/c/29988 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03mb/poppy/variant/nami: Move FPMCU_INT_L gpios to B groupShelley Chen
We discovered that the gpios previously used for FPMCU_INT_L were in two different groups with two different voltages (C group was at 3.3V and D group was at 1.8V). Moving both to B group which is at 3.3V. BUG=b:119447525 BRANCH=Nami TEST=unlock OS with fingerprint register fingerprint run powerd_dbus_suspend and see if it goes int s0ix Change-Id: I2332b0eb7a2f74e8178b95a23c8ac2091027a071 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/29872 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-12-03mb/google/fizz/variants/karma: Update USB port infoDavid Wu
Update USB port info according to the schematic file. BUG=none BRANCH=master TEST=Compiles successfully and boot on DUT. Change-Id: I7383b3d676fd7c775a6d749c70af65b28cf941eb Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/29912 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-12-03mb/google/fizz/variants/karma: Disable native SD card controllerDavid Wu
This change selects Kconfig option to disable native SD card controller in ACPI tables. BUG=b:119798840 BRANCH=master TEST=Compiles successfully and boot on DUT. Change-Id: I68dc9be511a370d882e4656c165efbe5dc6ee52e Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/29918 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-12-03soc/intel/cannonlake: Load FSP teardown optionallyLijian Zhao
Make build still pass in case of no FsptUpd.h available. BUG=N/A TEST=Delete FsptUpd.h and build pass wihtout FSP_CAR set. Change-Id: I3936d3deb8b079bd4db11e444f6bb7f9605520dc Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/c/29907 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-12-03soc/amd/stoneyridge: Create MMIO ACPI access functionsRichard Spiegel
Now that the relationship between IO access and MMIO access has been established, create read/write functions to access ACPI standard registers through MMIO. BUG=b:118049037 TEST=Build grunt Change-Id: I32c26f342885c0d99b082be98730edcf16ab5dfc Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/c/29295 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2018-12-03src/mb/pcengines/apu2/mainboard.c: Fix retrieving serial numberMichał Żygowski
Handle situation when first NIC is not BDF 1:0.0. The PCI enumeration is different when a external PCIe device is connected to mPCIe2 slot which is routed to first PCIe bridge. The first NIC is then assigned BDF 2:0.0, because it is connected to the second PCIe bridge. Read the secondary bus number from the NIC PCIe bridge before attempting to read MAC adress and calculating serial number. Change-Id: I9f89a6f3cd0c23a2d2924e587338f69c260b12f8 Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com> Reviewed-on: https://review.coreboot.org/c/29842 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-12-03nb/intel/gm45: Make fetching the blc_pwm freq globalArthur Heymans
This can be used to select the proper VBT. Change-Id: Id3f6ba3ae31a5ab47f44d207678c1c4a6a43b7ec Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/29925 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-12-03nb/intel/gm45: Make fetching the blc_pwm freq its own functionArthur Heymans
Also check the EDID string using strcmp instead of strncmp. Change-Id: I9ad364f84f3658be98ce7ad3a6f0f0fe3247fc41 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/29924 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-12-03sb/intel/lynxpoint/usb_{e,x}hci.c: Don't use device_tElyes HAOUAS
Use of device_t is deprecated. Change-Id: Ie75450c844e2317ded157465eb0fc6a9ec1b3ab0 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/29932 Reviewed-by: Patrick Rudolph <siro@das-labor.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03mb/google/dragonegg: Don't use device_tElyes HAOUAS
Use of device_t is deprecated. Change-Id: Ief858f6612d1c7b4b0c286cf5938f8c29055f1b5 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/29915 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-12-03include/device/smbus.h: Don't use device_tElyes HAOUAS
Use of device_t is deprecated. Change-Id: I2c88642133d3cbf33015e3e1e855fb2c786878d6 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/29914 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-12-03sb/intel/i82801gx: Clean up unneeded smi setup codeArthur Heymans
All i82801gx targets now use SMM_TSEG. Change-Id: Ib4e6974088a685290ed1dddf5228a99918744124 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/25599 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2018-12-03nb/intel/pineview: Use common code for SMM in TSEGArthur Heymans
This also caches the TSEG region and therefore increases MTRR usage a little in some cases. Change-Id: I5f947cfae730b67bc76a581bc90cb10e5a2a4a52 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/25598 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03nb/intel/x4x: Use common code for SMM in TSEGArthur Heymans
This also caches the TSEG region and therefore increases MTRR usage a little in some cases. Currently SMRR msr's are not set on model_1067x and model_6fx since this needs the MSRR enable bit and lock set in IA32_FEATURE_CONTROL. This will be handled properly in the subsequent parallel mp init patchset. Tested on Intel DG41WV, resume from S3 still works fine. Change-Id: I317c5ca34bd38c3d42bf0d4e929b2a225a8a82dc Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/25597 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03nb/intel/i945: Use common SMM_TSEG codeArthur Heymans
Use the common SMM_TSEG code to relocate the smihandler to TSEG. This also caches the TSEG region and therefore increases MTRR usage a little in some cases. This fixes S3 resume being broken introduced by CB:25594 "sb/intel/i82801gx: Use common Intel SMM code". Currently SMRR msr's are not set on model_1067x and model_6fx since this needs the MSRR enable bit and lock set in IA32_FEATURE_CONTROL. This will be handled properly in the subsequent parallel mp init patchset. Tested on Intel d945gclf and Lenovo Thinkpad X60. Change-Id: I0e6374746c3df96ce16f1c4a177af12747d6c1a9 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/25595 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03sb/intel/i82801jx: Use common Intel SMM codeArthur Heymans
Use the common Intel code to set up smm and the smihandler. This is expected to break S3 resume and other smihandler related functionality as this code is meant to be used with CONFIG_SMM_TSEG. The platform (x4x) using this southbridge will adapt the CONFIG_SMM_TSEG codepath in subsequent patches. Change-Id: Id3b3b3abbb3920d68d77fd7db996a1dc3c6b85a3 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/25596 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03nb/intel/gm45: Correctly cache TSEGArthur Heymans
Change-Id: I6a8752da9f92b90a2cb2cca5ebf28e2bc5a9c9a8 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/29866 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-03cbmem: Enable AArch64 supportAdam Kallai
TEST=on Chromebook Kevin with 64bit userland, it works well. Change-Id: If16065000214c6cff9c14a14c5b5f44faca38153 Signed-off-by: Adam Kallai <kadam@inf.u-szeged.hu> Reviewed-on: https://review.coreboot.org/c/29978 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-12-03soc/intel/apl: Configure LPC serial IRQ modeNico Huber
Sync the FSP settings with what coreboot does. Why both FSP and coreboot configure this redundantly stays a secret. TEST=Set SERIRQ_CONTINUOUS on kontron/mal10. A CPLD connected to LPC works correctly now, but was confused by the wrong settings before because the FSP defaults allowed to disable the LPC clock. Change-Id: Id1c7180f460678bf0f9458228591050dd628c052 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/c/29901 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2018-11-30cpu/intel/common: Use a common acpi/cpu.asl fileArthur Heymans
Change-Id: Ifa5a3a22771ff2e0efa14fb765603fd5e0440d59 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/29894 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: David Guckian
2018-11-30soc/intel/fsp_baytrail: Rework acpi/cpu.aslArthur Heymans
Use acpigen_write_processor_cnot to implement notifications to the CPU. Change-Id: I01e4397b9a1c15eff4b856cbc697fa2b4bc9761f Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/29893 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-11-30soc/intel/denverton_ns: Rework acpi/cpu.aslArthur Heymans
Use acpigen_write_processor_cnot to implement notifications to the CPU. Change-Id: If482c64e7133cc6d82472d121ac138fc1b60a183 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/29892 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: David Guckian
2018-11-30soc/intel/common: Rework acpi/cpu.aslArthur Heymans
Use acpigen_write_processor_cnot to implement notifications to the CPU. Change-Id: Id64f9857bbd7db520c94de949db8f823f71d6dae Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/29891 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-11-30soc/intel/broadwell: Rework acpi/cpu.aslArthur Heymans
Use acpigen_write_processor_cnot to implement notifications to the CPU. Automatically generate \PPKG in SSDT. Change-Id: I79d2eed9b89b420554ce10d1fc0f151b1872afe2 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/29890 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-11-30soc/intel/braswell: Rework acpi/cpu.aslArthur Heymans
Use acpigen_write_processor_cnot to implement notifications to the CPU. Change-Id: I93c11e89da34c5432c6ce0415998b47bad339763 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/29889 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 04:54:34 +0000