summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-06-17AMD: Use same sourcecode for reset in romstage as ramstageKyösti Mälkki
Confusingly, romstage compiled in different copy of soft_reset() than ramstage. Use source in reset.c for both. Change-Id: I2e4b6d1b89c859c7cf5d9e9c8f7748b43d369775 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3487 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-17AMD boards: Clean use of Kconfig optionsKyösti Mälkki
The chip component is unconditionally selected for the mainboard so these uses are superfluous. Change-Id: I84b053ab47f7b1f68e88d968cf305e24bc95f4da Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3485 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-17Add support for XHCI (USB 3.0)Dave Frodin
CONFIG_HUDSON_XHCI_ENABLE will control the XHCI flags in the amd/parmer and asus/f2a85-m mainboards. The XHCI ports on amd/thatcher are not wired to USB jacks so always disable the flags. This was tested on amd/parmer using a USB 3.0 thumbdrive. Change-Id: I596b040fec30882d8d4dee34ab9f866dc1f8896b Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/3465 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-17AMD Hudson: Add config option to enable XHCIDave Frodin
To have USB 3.0 support the XHCI controller needs to be enabled and the xhci.bin firmware needs to be added to CBFS. Change-Id: I0b641b30b67163b7dc73ee7ae67efe678e11c000 Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/3464 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-17pnp: Remove now plain wrappers for default PnP functionsNico Huber
After removing the enter()/exit() functions for configuration mode, most wrappers for our standard PnP functions just call the underlying default implementation. Remove those with a little cocci: @ op_match @ identifier op; identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$"; type device_t; identifier dev; @@ static void op(device_t dev) { pnp_op(dev); } @@ identifier op_match.op; @@ -op(...) {...} /* Three rules to match the alignment, hmmp... */ @@ identifier op_match.op, op_match.pnp_op; identifier ops; @@ struct device_operations ops = { - .set_resources = op, + .set_resources = pnp_op, }; @@ identifier op_match.op, op_match.pnp_op; identifier ops; @@ struct device_operations ops = { - .enable_resources = op, + .enable_resources = pnp_op, }; @@ identifier op_match.op, op_match.pnp_op; identifier ops; @@ struct device_operations ops = { - .enable = op, + .enable = pnp_op, }; Change-Id: Idc0e52c7e3600a01f3b6a4e17763557b271b481e Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/3483 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-17pnp: Register implementations of enter/exit config stateNico Huber
Find all the (ramstage) implementations of enter()/exit() functions for the configuration state, register and call them through the new struct pnp_mode_ops. As our standard PnP functions are aware of the pnp_mode_ops, it's not necessary to call enter()/exit() around them anymore. Patch generated with the cocci below. It's not perfect. The movement of the enter()/exit() calls is somehow fragile. So I checked the remaining calls for sense, and changed some empty lines. Also a duplicate insertion of pnp_conf_mode_ops had to be removed. /* Try to find enter and exit functions by their outb() structure and their usage around calls to our standard pnp functions: */ @ enter_match @ identifier enter; identifier dev; type device_t; @@ void enter(device_t dev) { <... outb(..., dev->path.pnp.port); ...> } @ exit_match @ identifier exit; identifier dev; type device_t; @@ void exit(device_t dev) { <... outb(..., dev->path.pnp.port); ...> } @ pnp_match @ identifier op; identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$"; identifier enter_match.enter, exit_match.exit; type device_t; identifier dev; @@ void op(device_t dev) { ... enter(dev); ... pnp_op(dev); ... exit(dev); ... } /* Now add enter/exit to a pnp_mode_ops structure: */ @ depends on pnp_match @ identifier enter_match.enter; identifier exit_match.exit; identifier ops; @@ +static const struct pnp_mode_ops pnp_conf_mode_ops = { + .enter_conf_mode = enter, + .exit_conf_mode = exit, +}; + struct device_operations ops = { ..., + .ops_pnp_mode = &pnp_conf_mode_ops, }; /* Match against the new structure as we change the code and the above matches might not work anymore: */ @ mode_match @ identifier enter, exit, ops; @@ struct pnp_mode_ops ops = { .enter_conf_mode = enter, .exit_conf_mode = exit, }; /* Replace enter()/enter() calls with new standard calls (e.g. pnp_enter_conf_mode()): */ @@ identifier mode_match.enter; expression e; @@ -enter(e) +pnp_enter_conf_mode(e) @@ identifier mode_match.exit; expression e; @@ -exit(e) +pnp_exit_conf_mode(e) /* If there are calls to standard PnP functions, (re)move the enter()/exit() calls around them: */ @@ identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$"; expression e; @@ -pnp_enter_conf_mode(e); pnp_op(e); +pnp_enter_conf_mode(e); ... pnp_exit_conf_mode(e); @@ identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$"; expression e; @@ pnp_enter_conf_mode(e); ... +pnp_exit_conf_mode(e); pnp_op(e); -pnp_exit_conf_mode(e); @@ expression e; @@ -pnp_enter_conf_mode(e); -pnp_exit_conf_mode(e); Change-Id: I5c04b0c6a8f01a30bc25fe195797c02e75b6c276 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/3482 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-17pnp: Implement common handling for PnP config modesNico Huber
Many super i/o chips only answer to PnP requests if they are in a configuration state (sometimes also called ext func mode). To cope with that, the code of many chips implements its own version of our default PnP functions like pnp_set_resource(), pnp_enable_resource() etc. To avoid this code duplication, this patch extends our PnP device interface with optional functions to enter and exit configuration mode. Change-Id: I9b7662a0db70ede93276764fa15020f251eb46bd Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/3481 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-17pnp: Provide alternative pnp_enable() implementationNico Huber
The current default implementation of pnp_enable() only disables devices - if set so in the devicetree - but does not enable them. Enablement takes place in pnp_enable_resources(). Yet, many PnP chips implement their own version of pnp_enable() which also enables devices if set in the devicetree. It's arguable, if enabling those devices makes sense, before they get resources assigned. Maybe we can't write the resource registers if not, who knows? The least we can do is providing a common implementation for this behavior, and get rid of some code duplication. Used the following cocci: @@ expression e; @@ +pnp_alt_enable(e); -pnp_set_logical_device(e); ( -pnp_set_enable(e, !!e->enabled); | -(e->enabled) ? pnp_set_enable(e, 1) : pnp_set_enable(e, 0); | -if (e->enabled) { pnp_set_enable(e, 1); } -else { pnp_set_enable(e, 0); } ) Change-Id: I8d695e8fcd3cf8b847b1aa99326b51a554700bc4 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/3480 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-17libpayload: ahci: Fix command engine shutdownNico Huber
A timeout while waiting for a device' signature has shown that our error path wasn't correct. The shutdown of the ports command engine always timed out. Fix that by waiting for FR (FIS Receive Running) to be cleared independently from CR (Command List Running) and after clearing FRE (FIS Receive Enable). Change-Id: I50edf426ef0241424456f1489a7fc86a2cfc5753 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3494 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-17Make intel blob locations configurablePatrick Georgi
They were hard-coded to be copied from 3rdparty/ which isn't always the right choice. Since the defaults stay the same, this should be compatible. Change-Id: If2173bef86ad1fcf2335e13472ea8ca41eb41f3d Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Reviewed-on: http://review.coreboot.org/3453 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-17pnp: Unify some alignment to ease autogenerating patchesNico Huber
Most PnP drivers align the initialization of their `device_operations` with spaces. Unify this, so next autogenerated patches always match the alignment. Change-Id: I3f6baef6c8bb294c136354754125ea88c07a61a1 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/3479 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-17qemu: i440fx whitespace fixupGerd Hoffmann
Change-Id: I0d499027ffb175638cba0a9830d6ec2041a139db Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-on: http://review.coreboot.org/3488 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-17qemu: add q35 supportGerd Hoffmann
Add support for the new q35 chipset emulation added in qemu 1.4. Change-Id: Iabfaa1310dc7b54c9d224635addebdfafe1fbfaf Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-on: http://review.coreboot.org/3430 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-17qemu: add support for memory above 4GGerd Hoffmann
Change-Id: Ic83f55d01b29b43028e3b363749d64b927db5489 Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-on: http://review.coreboot.org/3492 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-17qemu: move ram ressource reservation from "set" to "read" stageGerd Hoffmann
So the pci allocation code knows where memory is and doesn't try map pci devices there. We also don't have to check for overlaps between pci hole and memory then. Change-Id: I5eaea0e4d21210719685860fa1f16ca7b2137cde Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-on: http://review.coreboot.org/3491 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-17cpu/amd/geode_lx/cache_as_ram.inc: Use $ for constant value instead of ↵Christopher Kilgour
memory reference An uninitialized RAM value was used to select an MSR because a $ was forgotten in front of `CPU_DM_CONFIG0`. It should be the constant value 0x1800, corresponding to CPU_DM_CONFIG0 MSR defined in `src/include/cpu/amd/lxdef.h`. Change-Id: Id53ca98b06cc4a9b55916fd8db23904f98008d45 Signed-off-by: Christopher Kilgour <techie@whiterocker.com> Reviewed-on: http://review.coreboot.org/3478 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2013-06-14AMD sb800 agesa/hudson: Use PCI definesKyösti Mälkki
The original lines had contradicting comment and code. This change follows the code and sets MASTER bit too. Change-Id: Id2886bfc107612530f0e9747e5d49a9740fb8532 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3466 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-06-14qemu: move i440fx bitsGerd Hoffmann
Prepare tree for adding q35 support: Move emulation/qemu-x86 to emulation/qemu-i440fx. Rename some stuff to include 'i440fx'. Change-Id: Ib8c58175c5734cfcda1b22404ef52c09d38f0462 Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-on: http://review.coreboot.org/3429 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-14usbdebug: Drop temporary disables of log outputKyösti Mälkki
With this patch, output on usbdebug also includes the section of MTRR setups for every CPU. This makes usbdebug output almost identical with that of serial port and CBMEM console. Tested with model_206ax. Also tested previously on model_f2x which does not have these disable/enable calls in model_f2x_init() without detected issues. Change-Id: Idfd0e93439907b17255633658195d698feab3895 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3423 Reviewed-by: Aaron Durbin <adurbin@google.com> Tested-by: build bot (Jenkins)
2013-06-14lynxpoint: Fix PCI IDs for EHCIKyösti Mälkki
IDs were leftovers from bd82x6x. Change-Id: I4ab6062929d346d7f000ce8c0b8c97490bb2b154 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3463 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@google.com> Tested-by: build bot (Jenkins)
2013-06-13AMD Hudson: Add support for the SD controllerDave Frodin
This patch provides the correct SD controller timings for the Family16 device. It also will remove the SD controller from PCI space when device 0:14.7 is set to off in devicetree. This was tested on a AMD Parmer board and a AMD G-series SOC reference board. The settings were found in the AMD Hudson2 RRG and family16 BKGD. Change-Id: I6d7e7997ddc39802ab75dc8a211ed29f028c0471 Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/3348 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13libpayload: Fill gaps in the xHCI driverNico Huber
Well, it turned out to be more as some gaps ;) but we finally have xHCI running. It's well tested against a QM77 Ivy Bridge board. We have no SuperSpeed support (yet). On Ivy Bridge, SuperSpeed is not advertised and USB 3 devices will just work at HighSpeed. There are still some bit fields in xhci_private.h, so this might need little more work to run on ARM. Change-Id: I7a2cb3f226d24573659142565db38b13acdc218c Signed-off-by: Nico Huber <nico.huber@secunet.com> Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Reviewed-on: http://review.coreboot.org/3452 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13libpayload: Port usb hub driver to use the generic codeNico Huber
This is mostly a rewrite, don't even try to read a diff. Tested with an internal rate matching hub on a QM77 board and three hubs integrated into DELL monitors. Change-Id: Ib12fa2aa90af4e0f37143d2ed92c4a1705b6d774 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3451 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13libpayload: Add a generic driver for usb hubsNico Huber
The current drivers for external usb hubs and root hubs all follow the same pattern. Before adding another one with 90% of the same code, extract the common parts and rewrite them with a simple interface. This also adds debouncing of new attachments. Current drivers just waited 100ms before they reset the device. However, we should check if the device becomes disconnected and reconnected during this period. Porting of the current hub drivers will take place in separate commits (when I have time to test the older HCIs). Change-Id: I0c0ce0ac1b1cc51fb4cd009b3f9fcd1b9d2ba8fe Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3450 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13libpayload: usb: Add interval attribute to endpointsNico Huber
Read bInterval from endpoint descriptors and store it in our endpoint_t struct. The interval is encoded dependently on the device' speed and the endpoint's type. Therefore, it will be normalized to the binary logarithm of the number of microframes, i.e. t = 125us * 2^interval The interval attribute will be used in the xHCI driver. Change-Id: I65a8eda6145faf34666800789f0292e640a8141b Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3449 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13libpayload: Redirect USB slave init through controller driverPatrick Georgi
xHCI requires special treatment of set_address since it determines the device number itself (instead of the driver, as with the other controllers). The controller also wants to validate a chosen device configuration and we need to setup additional structures for the device and the endpoints. Therefore, we add three functions to the hci_t structure, namely: set_address() finish_device_config() destroy_device() Current implementation for the Set Address request moved into generic_set_address() which is set_address() for the UHCI, OCHI and EHCI drivers. The latter two are only provided as hooks for the xHCI driver. The Set Configuration request is moved after endpoint enumeration. For all other controller drivers nothing changes, as there is no other device communication between the lines where the set_configuration() call moved. Change-Id: I6127627b9367ef573aa1a1525782bc1304ea350d Signed-off-by: Nico Huber <nico.huber@secunet.com> Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Reviewed-on: http://review.coreboot.org/3447 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13libpayload: Add enum for USB speedsNico Huber
These values are already used in this usb stack. Change-Id: If96f1dc2b67fbc13dfc4ae2d84e8f9945aa03163 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3448 Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13libpayload: usb: Skip non-endpoint descriptors during initNico Huber
During device initialization, skip any non-endpoint descriptor before reading the endpoint descriptors. By now, only HID descriptors were skipped. Change-Id: I190f3ae44b864aa71d5f32c3738097cf8f33a61b Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3446 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
2013-06-13util/inteltool: Add support for other 5 chipsetsStefan Tauner
e4e8e090fa36cb3a098e1ddf0ea44c796c140572 does add support for QM57, but there are many more that should work with that code(?). Does not explode on... CPU: Processor Type: 0, Family 6, Model 25, Stepping 2 Northbridge: 8086:0044 (1st generation (Westmere family) Core Processor) Southbridge: 8086:3b0f (QS57) Change-Id: I85e15ba45678a5bd635415a7a8d69c05bff8f7ef Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at> Reviewed-on: http://review.coreboot.org/3321 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
2013-06-13AMD S3 resume: use a function to replace duplicated codeSiyuan Wang
In function OemAgesaSaveMtrr of 'src/cpu/amd/agesa/s3_resume.c', there are many code like this: msr_data = rdmsr(0x258); flash->write(flash, nvram_pos, 4, &msr_data.lo); nvram_pos += 4; flash->write(flash, nvram_pos, 4, &msr_data.hi); nvram_pos += 4; Add a function write_mtrr to do this. Change-Id: Id6464e637db1758b07ac2d79d3be1375a8d49651 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/3410 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13AMD Thatcher: fix issue 'S3 fails to suspend after wake up from USB keyboard'Siyuan Wang
This issue can be reproduced in Linux by the following steps: 1) use pm-suspend to suspend. 2) use USB keyboard to wake up. 3) use pm-suspend to suspend. FAIL To SUSPEND. The cause of this issue is: USB devices use bit 11(0x0b) of GP0_STS represents S3 wake up event, but this bit is not clear after wake up. So OS thinks there is a wake up signal and wake up immediately. In this patch, I add AcpiGpe0Blk using MMIO access and write 1 on bit 11. Write 1 to clear as spec says. I have tested on Thatcher The same change was done for AMD Parmer in commit »AMD Parmer: fix issue 'S3 fails to suspend after wake up from USB keyboard' (03901124) [1]. [1] http://review.coreboot.org/#/c/3347/ (Change-Id: Iec3078bf29de99683e7cd3ef4e178fbeb4dc09c1) Change-Id: Iaef39237497ef896d0f186e8f5522222c0ce6cb7 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/3374 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13AMD: Kconfig cleanupKyösti Mälkki
Change-Id: I21182eae1d389790c330f27e6a830d91c3ee4eb6 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3433 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-13Add support for Intel Nehalem CPUVladimir Serbinenko
Change-Id: I7ecc394b1e5bc0b8b85a8afac22efc0befe2d36a Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/3395 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13Revert "Add support for Intel Ibex Peak (Mobile 5) southbridge"Stefan Reinauer
This reverts commit 0210119b4b95e84f954cfd6dc11aafbc187421af Change-Id: I5be3f2a54394c592650a0dcd671e4a72ae796cb2 Reviewed-on: http://review.coreboot.org/3443 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-12Add support for Intel Ibex Peak (Mobile 5) southbridgeStefan Reinauer
Change-Id: If56f2cacc5f1b2ef9c7b6aea508d458a43dd1309 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/3397 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-12Avoid tripping overheat alarm on X201 before ME bootsVladimir Serbinenko
Until ME boots (which takes seconds on X201) the reported temperature is 128 °C which triggers Linux overheat alarm which shuts down. Pretend temperature is 40°C until ME boots. Change-Id: Ia49fa03c6eb27f539a23711f2c8ebfde72b1dc18 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/3404 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-12Make acpi/ec.c usable in romstageVladimir Serbinenko
On X201 to enable EHCI debug you need to go through EC if USB power is disabled so we need to inclue ec.c. Change-Id: I8f8b7de639ecaebceaa53cd338136befaeec8214 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/3405 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-12Radio and dock support in EC on X60 and X201Vladimir Serbinenko
Enable UMTS on Lenovo X60 and X201. Enable radios if no options are available. Enable dock on Lenovo X201. Based on my X201 branch. Change-Id: I6e8d3bbd6a6b1a8e59473dd5cc8125a1583d75df Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/3377 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-12am335x: Add struct `am335x_uart` for uart registersDavid Hendricks
Add a struct for referencing UART registers. The layout is quite strange on this chip, as the entire register space can take on three different meanings depending on the line control settings (in the LCR register) And to make things more confusing, some offsets reference different registers depending on if a read or a write operation is used. Change-Id: Ie62af9c0e0edafd01b81686a0fe5c5c1d4fa06c4 Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/3319 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-12usbdebug: Quirk for board aopen/dxplplusuKyösti Mälkki
This ancient board with Intel e7505 invalidates cache while it does HW scrubbing for ECC in romstage. This breaks usbdebug console and prevents system from booting. If both EARLY_CONSOLE and USBDEBUG are selected, skip ECC scrubbing under these rare conditions to boot system. Change-Id: I6cb43bf69af54119f4a582dcaf498dd941d4c62d Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3385 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-12usbdebug: Drop printk within console_init()Kyösti Mälkki
In case with EARLY_CONSOLE, this printk is called before any other console is configured to transmit data. This outputs garbage on CONSOLE_SERIAL as baudrate is not yet programmed. For case without EARLY_CONSOLE, the order in which different console drivers initialize is obscure. Might sometimes work properly. Change-Id: I3792161e0a6dc17e17262048cc9136044dd69dc5 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3384 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-12usbdebug: Improve solving EHCI debug port problemsKyösti Mälkki
Add comment how one can debug the usbdebug hardware init. Do not send printk's to usbdebug console when one is debugging the usbdebug console initialisation itself. Change-Id: I21a285cb31cf64e853bc626f8b6a617bc5a8be19 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3382 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-12Fix i82801a/b/c/d IOAPICKyösti Mälkki
Setting IRQ delivery to FSB got lost in the rebase process for commit e6143531. I captured following error on dmesg and this patch fixes it for i82801dx. ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... ..... (found apic 0 pin 2) ... ....... failed. ...trying to set up timer as Virtual Wire IRQ... ..... works. Change-Id: I0768976cc6b0deab213ad9bd4771e0f278de634c Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3371 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-12Add spkmodem receiverVladimir Serbinenko
This is spkmodem receiver counterpart. Change-Id: Id27d32608502029fb6fcc8154f508811bf5ca77b Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/3411 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-12intel/*/smi.c: Output correct GPIO in ALT_GP_SMI_STS register dumpKonstantin Aladyshev
Mapping is as follows: bit 15 corresponds to GPIO15 ... bit 0 corresponds to GPIO0. Change-Id: I661ce56d9373887270ba3c0518892fbbe6d9de7c Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/3436 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-11intel/bd82x6x/Makefile.inc: Revert duplicate addition of `usb_debug.c`Paul Menzel
Currently in Intel BD82x6x southbridge’s `Makefile.inc` the file `usb_debug.c` is added twice to the build. This was introduced in commit 4063ede3fb571110c3e65c321049cc2687cc54fa Author: Ronald G. Minnich <rminnich@google.com> Date: Mon Feb 4 20:31:51 2013 -0800 bd82x6x: Fix compiling with USB debug port support Reviewed-on: http://review.coreboot.org/2784 but was unneeded because it had been already added in the following commit. commit 4141993536039e0d45caeacb745a89d388f0724b Author: Sven Schnelle <svens@stackframe.org> Date: Sat Jul 28 08:52:44 2012 +0200 bd82x6x: Fix CONFIG_USBDEBUG Reviewed-on: http://review.coreboot.org/1376 Therefore basically revert that hunk. There is no policy on how to order these additions, so leave it to a possible separate commit, unifying this. Kyösti Mälkki suspects that these additions were meant for the Intel Lynx Point [1]. [1] http://review.coreboot.org/#/c/3424/ Change-Id: Iaa8de6fcc0d6f3a0a92a28fcb603d7777aa8b24c Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/3425 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-11Fix cycle error in intel southbridges to display GPI statusKonstantin Aladyshev
Fix obvious mistake in cycle that displays GPI status I hope i found all duplicates of it. Change-Id: Ic21ff3ecab85953463e5c23daf808dd5edc82ff8 Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/3435 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-11am335x: Revert how the header load size is calculated to an earlier method.Gabe Black
The current method will treat hex values as 0 and would calculate the wrong size. This change switches back to an earlier method which used shell syntax to add the offset and size. Change-Id: I9fb2d9b323f113cc56a5ad2e38b47d2d22084f08 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3432 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-11winbond/w83627dhg: Add ACPI supportNico Huber
This is loosely based on Christoph Grenz' ACPI code for the W83627HF and makes use of the PnP super i/o ACPI framework. Change-Id: I5e1cd09b83c0041f440562d2a1b73e4560589cb7 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3288 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-11Start ACPI framework for PnP (super i/o) devicesNico Huber
I'm trying to make writing ACPI code for super i/o devices more comfortable. pnp.asl hosts some general cpp macros. The other four files are to be included in dsdt trees. They are controlled by cpp macros which should be defined/undefined before inclusion. Work was inspired by Christoph Grenz' ACPI code for the W83627HF. Change-Id: Idb55332ba9bc788c98964d30a450e0d734cf28ec Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3286 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-16 16:23:46 +0000