Age | Commit message (Collapse) | Author |
|
Along with upstream kernel for Retimer firmware upgrade, coreboot
provides DFPx under host router where each DFP has its PLD and DSM. The
DFPx's functions encapsulates power control through GPIO, PD
suspend/resume and modes setting for Retimer firmware update under NDA
scenario.
BUG=b:186521258
TEST=Booted to kernel and validated host router's DFPx properties after
decomposing SSDT table.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I81bef80729f6df57119f5523358620cb015e5406
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52712
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
List of changes:
1. Make the FSP notify phases name prior in comments section.
2. Fix discrepancies in FSP notify before and after postcode comments.
3. Add FSP notify postcode macros for after pci enumeration(0xa2)
and ready to boot(0xa3) call.
Change-Id: Ib4c825d5f1f31f80ad2a03ff5d6006daa7104d23
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52894
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The only use case for FSP-T in coreboot is for 'Intel Bootguard'
support at the moment. Bootguard can do verification FSP-T but there
is no verification on whether the FSP found by walkcbfs_asm is the one
actually verified as an IBB by Bootguard. A fixed pointer needs to be
used.
TESTED on OCP/Deltalake, still boots.
Change-Id: I1ec8b238384684dccf39e5da902d426d3a32b9db
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Only SOC_INTEL_BRASWELL is using FSP1.1. It has too little CAR
available set up by FSP-T to have VBOOT_STARTS_IN_BOOTBLOCK and
therefore verstage is not possible either.
Change-Id: I54361c835055907c2a4414ec26a1495425d4ef09
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52785
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Id56761b2a57754b8f8d726a4bd2674ffa6fd1159
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use `SOC_INTEL_COMMON_SKYLAKE_BASE` to simplify conditions.
Change-Id: Ie69bde31b58bbd973db00bd578a51477c5b21cab
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Timofey Komarov <happycorsair@yandex.ru>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
We had the addrspace_32bit rdev in prog_loaders.c for a while to help
represent memory ranges as an rdev, and we've found it useful for a
couple of things that have nothing to do with program loading. This
patch moves the concept straight into commonlib/region.c so it is no
longer anchored in such a weird place, and easier to use in unit tests.
Also expand the concept to the whole address space (there's no real need
to restrict it to 32 bits in 64-bit environments) and introduce an
rdev_chain_mem() helper function to make it a bit easier to use. Replace
some direct uses of struct mem_region_device with this new API where it
seems to make sense.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie4c763b77f77d227768556a9528681d771a08dca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a new configuration low_power_probe to avoid camera privacy LED
blink during the boot.
Change-Id: I27d5c66fb380ae6cd76d04ee82b7736407dac1b0
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52189
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Traditionally, for each Intel platform using FSP, FSP-S has at some
point configured GPIOs differently than the mainboard configuration in
coreboot. This has resulted in various side-effects in coreboot,
payload and OS because of misconfigured GPIOs. On more recent Intel
platforms, a UPD `GpioOverride` is added that coreboot can use to
ensure that FSP does not touch any GPIO configuration.
This change adds a debug option `CHECK_GPIO_CONFIG_CHANGES` to fsp2_0
driver in coreboot that makes a platform callback `gpio_snapshot` to
snapshot GPIO configuration before making a call to FSP SiliconInit
and Notify phases. This snapshot is then compared against the GPIO
configuration using platform callback `gpio_verify_snapshot` after
returning from FSP. The callbacks are not added to romstage (FSP-M)
because mainboard configures all pads in ramstage.
This debug hook allows developers to dump information about any pads
that have a different configuration after call to FSP in ramstage. It
is useful to identify missed UPD configurations or bugs in FSP that
might not honor the UPDs set by coreboot.
This debug hook expects the platform to implement the callbacks
`gpio_snapshot` and `gpio_verify_snapshot`. These can be implemented
as part of the common GPIO driver for platforms using
FSP2.0+. Platforms that implement this support must select the config
`HAVE_GPIO_SNAPSHOT_VERIFY_SUPPORT` to make the debug config
`CHECK_GPIO_CONFIG_CHANGES` visible to user.
Proposal for the GPIO snapshot/verify support was discussed in the RFC
CB:50829.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I5326fc98b6eba0f8ba946842253b288c0d42c523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50989
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch changes the Intel MMA driver to use the new CBFS API.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Icc11d0c2a9ec1bd7a1d6af362f849dac16375433
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch ports the last remaining use of cbfs_boot_locate() in the
Intel FSP drivers to the new CBFS API. As a consequence, there is no
longer a reason for fsp_validate_component() to operate on rdevs, and
the function is simplified to take a direct void pointer and size to a
memory-mapping of the FSP blob instead.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If1f0239eefa4542e4d23f6e2e3ff19106f2e3c0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52281
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DPTF HIDs are different per-platform going forward, so refactor these
into SoC-specific structures which the DPTF driver can query at runtime
for platform-specific information.
Change-Id: I6307f9d28f4274b851323ad69180ff4ae35053da
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
The only FSP 1.1 platform with MMA support is Skylake. As it now uses
Kaby Lake FSP 2.0, this code is no longer useful. Drop it.
Change-Id: I819c3152bdea0fdad629793d96136ef134429fbd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The Intel FSP 2.0 driver contains a custom construct that basically
serves the same purpose as the new CBFS allocator concept: a callback
function to customize placement of a loaded CBFS file whose size is
initially unknown. This patch removes the existing implementation and
replaces it with a CBFS allocator.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0b7b446a0d2af87ec337fb80ad54f2d404e69668
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Until now every AML package had to be closed using acpigen_pop_len().
This commit introduces set of package closing functions corresponding
with their opening function names. For example acpigen_write_if()
opens if-statement package, acpigen_write_if_end() closes it.
Now acpigen_write_else() closes previously opened acpigen_write_if(),
so acpigen_pop_len() is not required before it.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Icfdc3804cd93bde049cd11dec98758b3a639eafd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Since prog_locate() was eliminated, prog_rdev() only ever represents the
loaded program in memory now. Using the rdev API for this is unnecessary
if we know that the "device" is always just memory. This patch changes
it to be represented by a simple pointer and size. Since some code still
really wants this to be an rdev, introduce a prog_chain_rdev() helper to
translate back to that if necessary.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If7c0f1c5698fa0c326e23c553ea0fe928b25d202
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch rewrites the last few users of prog_locate() to access CBFS
APIs directly and removes the call. This eliminates the double-meaning
of prog_rdev() (referring to both the boot medium where the program is
stored before loading, and the memory area where it is loaded after) and
makes sure that programs are always located and loaded in a single
operation. This makes CBFS verification easier to implement and secure
because it avoids leaking a raw rdev of unverified data outside the CBFS
core code.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7a5525f66e1d5f3a632e8f6f0ed9e116e3cebfcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
EFI_PEI_MP_SERVICES_STARTUP_ALL_APS passes in a boolean flag singlethread
which indicates whether the work should be scheduled in a serially on all APs
or in parallel. Current implementation of this function mp_startup_all_aps
always schedules work in parallel on all APs. This implementation ensures
mp_startup_all_aps honors to run serialized request.
BUG=b:169114674
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I4d85dd2ce9115f0186790c62c8dcc75f12412e92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51085
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use lowercase `port` in both the spec and the body.
Change-Id: I3d1e2abe03eedcaf57716af444a3e3b8a61b60d4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
RAM is not yet configured in bootblock. This function was copy-pasted
from Broadwell. Also, Skylake no longer uses FSP 1.1 and the stubs in
there can be removed as nothing else uses them.
Change-Id: I22cb7e63ed1e9565934296fd40771130ba91d227
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50949
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Idc96b99da9f9037267c0bec2c839014b13ceb8cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51106
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
From JSL FSP v2376 "FirmwareVersionInfo.h" header file is
added and "FirmwareVersionInfoHob.h" is deprecated. This patch
adds support to display firmware version information using
"FirmwareVersionInfo.h" header file.
Changes included in this patch:
- Add Kconfig to select FirmwareVersionInfo.h
- Add code change to display firmware version info using
FirmwareVersionInfo.h header
No change in version info print format.
BUG=b:153038236
BRANCH=None
TEST=Verify JSLRVP build with all the patch in relation chain
and verify the version output prints no junk data observed.
couple of lines from logs are as below.
Display FSP Version Info HOB
Reference Code - CPU = 8.7.16.10
uCode Version = 0.0.0.1
Change-Id: I50f7cae9ed4fac60f91d86bdd3e884956627e4b5
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
FSP expects mp_get_processor_info to give processor specfic apic ID,
core(zero-indexed), package(zero-indexed) and thread(zero-indexed) info.
This function is run from BSP for all logical processor, With current
implementation the location information returned is incorrect per logical
processor. Also the processor id returned does not correspond to the
processor index, rather is returned only for the BSP.
BUG=b:179113790
Change-Id: Ief8677e4830a765af61a0df9621ecaa372730fca
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50880
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If the UPD size in coreboot sizes mismatches the one from the FSP-M
binary, we're running into trouble. If the expected size is smaller than
the UPD size the FSP provides, call die(), since the target buffer isn't
large enough so only the beginning of the UPD defaults from the FSP will
get copied into the buffer. We ran into the issue in soc/amd/cezanne,
where the UPD struct in coreboot was smaller than the one in the FSP, so
the defaults didn't get completely copied.
TEST=Mandolin still boots.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia7e9f6f20d0091bbb4abfd42abb40b485da2079d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enforcing the exact match of FSPS UPD block size between FSP and
coreboot mandates simultaneous updates to coreboot and FSP repos. Allow
coreboot to proceed if its UPD structure is smaller than FSP one. This
usually indicates that FSPS has an updated (larger) UPD structure which
should be soon matched/updated on the coreboot side to keep them in
sync.
While this is an undesirable situation that should be corrected
ASAP, it is safe from coreboot perspective. It is safe (as long as
default values in FSP UPD are sane enough to boot) because FSPS UPD
buffer is allocated on the heap with the size specified in FSPS
(larger) and filled with FSPS default values. This allows FSP UPD
changes to be submitted first followed by changes in coreboot repo.
Note that this only applies to the case when entire FSPS UPD structure
grows which should be rare as FSP should allocate enough reserve space,
anticipating future expansion, to keep the structure from growing when
new members are added.
BUG=b:171234996
BRANCH=Zork
TEST=build Trembyle
Change-Id: I557fd3a1f208b5b444ccf76e1552e74ecf4decad
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Found using:
diff <(git grep -l '#include <string.h>' -- src/) <(git grep -l 'STRINGIFY\|memcpy\|memmove\|memset\|memcmp\|memchr\|strdup\|strconcat\|strnlen\|strlen\|strchr\|strncpy\|strcpy\|strcmp\|strncmp\|strspn\|strcspn\|strstr\|strtok_r\|strtok\|atol\|strrchr\|skip_atoi\|snprintf' -- src/)|grep '<'
Change-Id: Ief86a596b036487a17f98469c04faa2f8f929cfc
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
ACPI S3 is a global state and it is no longer needed to
pass it as a parameter.
Change-Id: Id0639a47ea65c210b9a79e6ca89cee819e7769b1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Hide the detail of allocation from cbmem from the FSP.
Loading of a BMP logo file from CBFS is not tied to FSP
version and we do not need two copies of the code, move
it under lib/.
Change-Id: I909f2771af534993cf8ba99ff0acd0bbd2c78f04
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Icb3108a281dfb3f21248a7065821b8237143be1a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ie4692246d059734bb5bad6c64042b64068636ab6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add support for MP services2 PPIs, which is slight modification
over MP services 1 PPIs. A new API StartupAllCPUs have been added
to allow running a task on BSP and all APs. Also the EFI_PEI_SERVICES
parameter has been removed from all MP PPI APIs.
This implementation also selects the respective MP services PPI version
supported for SoCs
BUG=b:169196864
Change-Id: Id74baf17fb90147d229c78be90268fdc3ec1badc
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change renames config FSP_USES_MP_SERVICES_PPI to MP_SERVICES_PPI
in preparation to allow V1 and V2 versions of MP services PPI.
TEST=Verified that timeless build for brya, volteer, icelake_rvp,
elkhartlake_crb and waddledee shows no change in generated coreboot.rom
Change-Id: I04acf1bc3a3739b31d6e9d01b6aa97542378754f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50275
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops the config FSP_PEIM_TO_PEIM_INTERFACE.
FSP_PEIM_TO_PEIM_INTERFACE is used for:
* Auto-selecting FSP_USES_MP_SERVICES_PPI
* Including src/drivers/intel/fsp2_0/ppi/Kconfig
* Adding ppi to subdirs-y
* Setting USE_INTEL_FSP_TO_CALL_COREBOOT_PUBLISH_MP_PPI to y
and is selected by SoCs that want to enable MP PPI services.
Instead of using the indirect path of selecting MP PPI services, this
change allows SoC to select FSP_USES_MP_SERVICES_PPI directly. The
above uses are handled as follows:
* Auto-selecting FSP_USES_MP_SERVICES_PPI
--> This is handled by SoC selection of FSP_USES_MP_SERVICES_PPI.
* Including src/drivers/intel/fsp2_0/ppi/Kconfig
--> The guard isn't really required. The Kconfig options in this
file don't present user prompts and don't really need to be guarded.
* Adding ppi to subdirs-y
--> Makefile under ppi/ already has conditional inclusion of files
and does not require a top-level conditional.
* Setting USE_INTEL_FSP_TO_CALL_COREBOOT_PUBLISH_MP_PPI to y
--> This is set to y if FSP_USES_MP_SERVICES_PPI is selected by SoC.
TEST=Verified that timeless build for brya, volteer, icelake_rvp,
elkhartlake_crb and waddledee shows no change in generated coreboot.rom
Change-Id: I0664f09d85f5be372d19925d47034c76aeeef2ae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50274
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new Kconfig symbols to mark FSP binary as x86_32.
Fix the FSP headers and replace void pointers by fixed sized integers
depending on the used mode to compile the FSP.
This issue has been reported here:
https://github.com/intel/FSP/issues/59
This is necessary to run on x86_64, as pointers have different size.
Add preprocessor error to warn that x86_64 FSP isn't supported by the
current code.
Tested on Intel Skylake. FSP-M no longer returns the error "Invalid
Parameter".
Change-Id: I6015005c4ee3fc2f361985cf8cff896bcefd04fb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ide5673dc99688422c5078c8c28ca5935fd39c854
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
TESTED on ocp/tiogapass.
Change-Id: I30560149eeaec62af4c8a982815618be5546531c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Allow platforms to use the coreboot postcar code instead of calling
into FSP-M TempRamExit API.
There are several reasons to do this:
- Tearing down CAR is easy.
- Allows having control over MTRR's and caching in general.
- The MTRR's set up in postcar be it by coreboot or FSP-M are
overwritten later on during CPU init so it does not matter.
- Avoids having to find a CBFS file before cbmem is up (this
causes problems with cbfs_mcache)
Change-Id: I6cf10c7580f3183bfee1cd3c827901cbcf695db7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48466
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In case of a mismatch print both the UPD signature in the FSP and the
expected signature and then calls die(), since it shouldn't try calling
into the wrong FSP binary for the platform.
Signed-off-by: Justin Frodsham <justin.frodsham@protonmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I469836e09db6024ecb448a5261439c66d8e65daf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Factor out the condition when an attempt to load
stage from cache can be tried.
Change-Id: I936f07bed6fc82f46118d217f1fd233e2e041405
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Iaba88026906132b96fe3db3f05950df0e7eef896
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The function has only one local call-site.
Change-Id: I623953796e6cd3a8e5b4f72293d953b61f14a5a1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49999
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to FSP_INFO_HEADER structure in FSP EAS v2.0-v2.2,
BIT1 indicates an "official" build.
Change-Id: I94df6050a1ad756bbeff60cda0ebac76ae5f8249
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ia45825ade0c9d24d5b87882e21bfc6df82a693e6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Tested
- on ocp/deltalake: boots (with FSP-T).
- qemu/i440fx: BUILD_TIMELESS=1 results in the same binary.
Change-Id: I7e364ab039b65766eb95538db6b3507bbfbfb487
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add the "ERROR:" tag so that it ease debug effect.
TEST=Test tools like "suspend_stress_test" (specific to Chrome OS) can
identify the obvious coreboot ERROR prior running S3 resume test.
Change-Id: I64717ce0412d43697f42ea2122b932037d28dd48
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49798
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to update the BB retimers for usb4/tbt they need to be turned
on and into TBT mode. Expand the current DSM to allow for the use of an
EC RAM byte RFWU to get the current state of each port and whether or
not it has a retimer. It also allows Kernel to issue state transitions
for the retimer to be put into TBT mode for firmware update.
BUG=b:162528867
TEST=Along with work in progress kernel and EC patches, the Retimer
firmware update is verified under device attached and no device attached
scenarios.
Change-Id: I768cfb56790049c231173b0ea0f8e08fe6b64b93
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
prog_locate() will load FSP, before CBMEM is initialized.
The vboot workbuffer is used for loading, but
CBMEM_ID_VBOOT_WORKBUF is not available.
A NULL pointer is returned as workbuffer resulting in error
'Ramstage was not loaded!' at second boot.
Initialize CBMEM before calling prog_locate().
BUG = N/A
TEST = Build and boot on Facebook FBG1701
Change-Id: I2f04a326a95840937b71f6ad65a7c011268ec6d6
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I5866a5e3240e49119e29f728202b33dd82ceaf77
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
For arch/x86 the realmode part has to be located within the same 64
KiB as the reset vector. Some older intel platforms also require 4 KiB
alignment for _start16bit.
To enforce the above, and to separate required parts of .text without
matching *(.text.*) rules in linker scripts, tag the pre-C environment
assembly code with section .init directive.
Description of .init section for ELF:
This section holds executable instructions that contribute to the
process initialization code. When a program starts to run, the
system arranges to execute the code in this section before calling the
main program entry point (called main for C programs).
Change-Id: If32518b1c19d08935727330314904b52a246af3c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47599
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new macro `GMA_DEFAULT_PANEL(ssc)` as shortcut for specifying one
internal panel at port A (0) in the devicetree.
Change-Id: I5308b53667657d0b255ae5bc543f1a00431f5818
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|