| Age | Commit message (Collapse) | Author |
|---|
|
The SLEEP_STATE_x definitions in the chipsets utilizing
FSP 1.1. driver have the exact same values as the ACPI_Sx
definitions. The chipsets will be moved over subsequently,
but updating this first allows the per-chipset patches
to be isolated.
BUG=chrome-os-partner:54977
Change-Id: I383a9a732ef68bf2276f6149ffa5360bcdfb70b3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15665
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
|
|
This driver enables the usage of an external RTC chip PCF8523 which is
connected to the I2C bus. The I2C address of this device is fixed.
One can change parameters in device tree so that the used setup can be
adapted in device tree to match the configuration of the device on the
mainboard.
Change-Id: I2d7e161c9e12b720ec4925f1acfd1dd8ee6ee5f5
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15641
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Some devices allow to retrieve firmware version by reading the same 4
byte register repeatedly until the entire version string is read.
Let's print out TPM firmware version when available. Just in case
something goes wrong limit the version string length to 200 bytes.
CQ-DEPEND=CL:355701
BRANCH=none
BUG=chrome-os-partner:54723
TEST=built the new firmware and ran it on Gru, observed the following
in the coreboot console log:
Connected to device vid:did:rid of 1ae0:0028:00
Firmware version: cr50_v1.1.4792-7a44484
Original-Commit-Id: 1f54a30cebe808abf1b09478b47924bb722a0ca6
Original-Change-Id: Idb069dabb80d34a0efdf04c3c40a42ab0c8a3f94
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/355704
Original-Reviewed-by: Scott Collyer <scollyer@chromium.org>
Squashed with:
tpm: use 4 byte quantities when retrieving firmware version
The CR50 device is capable of reporting its firmware version in 4 byte
quantities, but the recently introduced code retrieves the version one
byte at a time.
With this fix the version is retrieved in 4 byte chunks.
BRANCH=none
BUG=none
TEST=the version is still reported properly, as reported by the AP
firmware console log:
localhost ~ # grep cr50 /sys/firmware/log
Firmware version: cr50_v1.1.4804-c64cf24
localhost ~ #
Original-Commit-Id: 3111537e7b66d8507b6608ef665e4cde76403818
Original-Change-Id: I04116881a30001e35e989e51ec1567263f9149a6
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/356542
Original-Reviewed-by: Andrey Pronin <apronin@chromium.org>
Change-Id: Ia9f13a5bf1c34292b866f57c0d14470fe6ca9853
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/15573
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The "PC Client Protection Profile for TPM 2.0" document defines SPI
bus addresses for different localities. That definition is not honored
in the cr50 implementation, this patch fixes it: locality zero
register file is based off 0xd40000.
BRANCH=none
BUG=chrome-os-partner:54720
TEST=with the fixed cr50 image and the rest of TPM2 initialization
patches applied factory initialization sequence on Gru succeeds.
Change-Id: I49b7ed55f0360448b9a6602ebd31a3a531608da3
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 43344fff5d58ec235e50030413fc38c98dd0a9a1
Original-Change-Id: I2de6fa6c05d3eca989d6785228d5adde1f2a7ab7
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/355620
Original-Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://review.coreboot.org/15568
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
|
|
Change-Id: I2c49d68ea9a8f52737b6064bc4fa703bdb1af1df
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15463
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a device driver to generate the device and required properties
into the SSDT.
This driver uses the ACPI Device Property interface to generate the
required parameters into the _DSD table format expected by the kernel.
This was tested on the reef mainboard to ensure that the SSDT contained
the equivalent parameters that are provided by the current DSDT object.
Change-Id: Ia809e953932a7e127352a7ef193974d95e511565
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15538
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
There is a second ACPI _DSD document from the UEFI Forum that details
how _DSD style tables can be nested, creating a tree of similarly
formatted tables. This document is linked from acpi_device.h.
In order to support this the device property interface needs to be
more flexible and build up a tree of properties to write all entries
at once instead of writing each entry as it is generated.
In the end this is a more flexible solution that can support drivers
that need child tables like the DA7219 codec, while only requiring
minor changes to the existing drivers that use the device property
interface.
This was tested on reef (apollolake) and chell (skylake) boards to
ensure that there was no change in the generated SSDT AML.
Change-Id: Ia22e3a5fd3982ffa7c324bee1a8d190d49f853dd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15537
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add driver code to initialize Siemens NC FPGA as PCI device.
Beside some glue logic it contains a FAN controller and
temperature monitor.
Change-Id: I2cb722a60081028ee5a8251f51125f12ed38d824
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15543
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The function mainboard_get_mac_address() is used to get a MAC address
for a given i210 PCI device. Instead of passing pure numbers for PCI
bus, device and function pass the device pointer to this function. In
this way the function can retrieve the needed values itself as well as
have the pointer to the device tree so that PCI path can be evaluated
there.
Change-Id: I2335d995651baa5e23a0448f5f32310dcd394f9b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15516
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The upstream kernel driver is not using the of-style naming for
sdmode-gpio so remove the maxim prefix, and remove the duplicate
entry for the sdmode-delay value as well.
Also fix the usage of the path variable, since the device path uses
a static variable it can't be assigned that early or it will be
overwritten by later calls.
This results in the following output for the _DSD when tested on
reef mainboard:
Name (_DSD, Package (0x02)
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package (0x02)
{
Package (0x02)
{
"sdmode-gpio",
Package (0x04)
{
\_SB.PCI0.HDAS.MAXM,
Zero,
Zero,
Zero
}
},
Package (0x02)
{
"sdmode-delay",
Zero
}
}
})
Change-Id: Iab33182a5f64c89151966f5e79f4f7c30840c46f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15514
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I22a33e6027a4e807f7157a0dfafbd6377bc1285d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15461
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Any FSP API call may request a reset. This is indicated in API function
return code. Add trivial reset handler code.
BUG=chrome-os-partner:54149
BRANCH=none
TEST=none
Change-Id: Ieb5e2d52ffdaf3c3ed416603f6dbb4f9c25a1a7b
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15334
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
To fully define TPM attachment to a SPI interface both bus and CS
(chip select) settings are required. Add the missing CS configuration
option.
BRANCH=none
BUG=chrome-os-partner:50645
TEST=with the rest of the patches applied it is possible to compile in
and run TPM2 SPI driver.
Change-Id: If297df8e5b9526f156ed1414eb9db317d6af5b33
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/353913
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15299
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This introduces a SPI TPM driver compliant with the TCG issued "TPM
Profile (PTP) Specification Revision 00.43" which can be found by
googling its title.
The driver implements both the hardware flow control protocol and the
TPM state machine.
The hardware flow control allows to map SPI based TPM devices to the
LPC address space on x86 platforms, on all other platforms it needs to
be implemented in the driver software.
The tis layer is somewhat superficial, it might have to be expanded
later.
A lot more implementation details can be found in the code comments.
Also, it is worth mentioning that this is not a complete version of
the driver: its robustness needs to be improved, delay loops need to
be bound, error conditions need to propagate up the call stack.
BRANCH=none
BUG=chrome-os-partner:52132, chrome-os-partner:50645, chrome-os-partner:54141
TEST=with the rest of the patches applied coreboot is able complete
Chrome OS factory initialization of the TPM2 device.
Change-Id: I967bc5c689f6e6f345755f08cb088ad37abd5d1c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 5611c6f7d7fe6d37da668f337f0e70263913d63e
Original-Change-Id: I17d732e66bd231c2289ec289994dd819c6276855
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/350124
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15298
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Tested-by: build bot (Jenkins)
|
|
Until now it was assumed that all TPM devices were of the same type
(TCG 1.2 spec compliant) and x86 based boards had LPC connected TPMs
and all other boards had I2C connected TPMs.
With the advent of TPM2 specification there is a need to be able to
configure different combinations of TPM types (TPM or TPM2) and
interfaces (LPC, I2C and SPI).
This patch allows to do it. Picking Chrome OS still assumes that the
board has a TPM device, but adding MAINBOARD_HAS_TPM2 to the board's
Kconfig will trigger including of TPM2 instead.
MAINBOARD_HAS_LPC_TPM forces the interface to be set to LPC, adding
SPI_TPM to the board config switches interface choice to SPI, and if
neither of the two is defined, the interface is assumed to be I2C.
BRANCH=none
BUG=chrome-os-partner:50645
TEST=verified that none of the generated board configurations change
as a result of this patch. With the rest of the stack in place it
is possible to configure different combinations of TPM types and
interfaces for ARM and x86 boards.
Change-Id: I24f2e3ee63636566bf2a867c51ed80a622672f07
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 5a25c1070560cd2734519f87dfbf401c135088d1
Original-Change-Id: I659e9301a4a4fe065ca6537ef1fa824a08d36321
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/349850
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/15294
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
|
|
This variable name was changed in chip.h but not the consumer
and it was submitted before it was caught.
Change-Id: I7c492b588b2fd854a9eeac36029a46da324a7b1b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15109
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Without RELOCATABLE_RAMSTAGE have WB cache large enough
to cover the greatest ramstage needs, as there is no benefit
of trying to accurately match the actual need. Choose
this to be bottom 16MiB.
With RELOCATABLE_RAMSTAGE write-back cache of low ram is
only useful for bottom 1MiB of RAM as a small part of this gets used
during SMP initialisation before proper MTRR setup.
Change-Id: Icd5f8461f81ed0e671130f1142641a48d1304f30
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15249
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I36056af9f2313eff835be805c8479e81d0b742bf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15196
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
FSP methods may require reset under certain conditions. That is indicated
by returning specific return code. Add the missing return status codes.
BUG=chrome-os-partner:54149
BRANCH=none
TEST=none
Change-Id: I460353c5f835548a98255bd3e11dbfd08260ea52
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15185
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Update autogenerated FSP 2.0 generic header files
based on FSP release 136_30.
Changes were made to avoid duplicating some of the
structs for every SoC.
BUG=chrome-os-partner:50765
TEST=Build coreboot
Change-Id: I6f3c9270fb67210d6ea87e17ccf52d203fa64b4b
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://chromium.devtools.intel.com/7145
Reviewed-by: Petrov, Andrey <andrey.petrov@intel.com>
Tested-by: Petrov, Andrey <andrey.petrov@intel.com>
Reviewed-on: https://chromium.devtools.intel.com/7584
Reviewed-on: https://review.coreboot.org/15081
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Previous FSP implementations in coreboot have included FspUpdVpd.h
directly, along with with efi headers. Instead of taking that
approach in FSP 2.0, we provide a semantic patch that, with minimal
modifications, makes FspUpdVpd.h easier to include in coreboot, and
eliminates reliance on external headers and definitions.
Change-Id: I0c2a6f7baf6fb50ae22b64e08e653cfe1aefdaf9
Signed-off-by: Alexandru Gagniuc <alexandrux.gagniuc@intel.com>
Reviewed-on: https://review.coreboot.org/13331
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Now that there is a better way of finding optional routines, make the
weak routines quiet so that it may be used for the optional
implementation.
TEST=Build and run on Galileo Gen2
Change-Id: Ic58c7de216394f80aee3a78dd08bd4682783be42
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15043
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Build the <board>_checklist.html file which contains a checklist table
for each stage of coreboot. This processing builds a set of implemented
(done) routines which are marked green in the table. The remaining
required routines (work-to-do) are marked red in the table and the
optional routines are marked yellow in the table. The table heading
for each stage contains a completion percentage in terms of count of
routines (done .vs. required).
Add some Kconfig values:
* CREATE_BOARD_CHECKLIST - When selected creates the checklist file
* MAKE_CHECKLIST_PUBLIC - Copies the checklist file into the
Documenation directory
* CHECKLIST_DATA_FILE_LOCATION - Location of the checklist data files:
* <stage>_complete.dat - Lists all of the weak routines
* <stage>_optional.dat - Lists weak routines which may be optionally
implemented
TEST=Build with Galileo Gen2.
Change-Id: Ie056f8bb6d45ff7f3bc6390b5630b5063f54c527
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15011
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update the weak functions for the MRC cache.
TEST=Build and run on Galileo Gen2
Change-Id: I54a1252cfff1a2f68b163f0feb65e2bceb37f6a9
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15042
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Maxim Integrated 98357A codec is an I2S slave device that has no
control channel for configuration and instead provides a GPIO that is
used for channel selection and power down. This means it does not fit
into a bus hierarchy easily and is instead represented as a generic
device and found with a static bus scan using the devicetree.
This driver provides configuration options for passing the "sdmode" GPIO
descriptor as well as a second option for "sdmode delay" which can
configure the timing of the sdmode toggling in relation to the I2S
channel output.
In addition an GPIO can be provided to indicate to the driver whether
this device is present or not. This can be used for board designs that
may have different codec possibilities that are selected by HW strap.
Sample usage for this device driver:
device pci 1f.3 on
chip drivers/generic/max98357a
register "sdmode_gpio" = "ACPI_GPIO_OUTPUT(GPP_C6)"
register "sdmode_delay" = "100"
device generic 0 on end
end
end
Will result in the following code in the SSDT:
Scope (\_SB.PCI0.HDAS) {
Device (MAXM) {
Name (_HID, "MX98357A")
Name (_UID, Zero)
Name (_DDN, "Maxim Integrated 98357A Amplifier")
Method (_STA) { Return (0xF) }
Name (_CRS, ResourceTemplate () {
GpioIo (Exclusive, PullDefault, 0, 0, IoRestrictionOutputOnly,
"\\_SB.PCI0.GPIO", 0, ResourceConsumer)
})
Name (_DSD, Package () {
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () { "maxim,sdmode-gpio", \_SB.PCI0.HDAS.MAXM, 0, 0, 0 }
Package () { "maxim,sdmode-delay", 100 }
Package () { "sdmode-delay", 100 }
}
})
}
}
Change-Id: Ia0bafe49bea9bbe4a3cc0f9f9cdb6f6390da57b5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15017
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This adds a generic I2C driver that can be described in the devicetree
and used to generate ACPI objects in the SSDT based on the information
provided in the config registers.
The I2C bus can be configured and the device can provide an interrupt and
wake capability to the OS. A configuration option allows for a GPIO to
be provided that will be checked to determine if the device is preset on
the board before including it in the generated SSDT.
The driver is generic enough to be used for basic I2C devices that do
not have special configuration needs such as touchpads, touchscreens,
sensors, some audio codec/amplifiers, etc.
Sample usage for a touchpad device:
device pci 15.1 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = "ELAN Touchpad"
register "irq" = "IRQ_EDGE_LOW(GPP_B3_IRQ)"
register "wake" = "GPE0_DW0_05"
device i2c 15.0 on end
end
end
Will result in the following code in the SSDT:
Scope (\_SB.PCI0.I2C1) {
Device (D015) {
Name (_HID, "ELAN0000")
Name (_UID, 0)
Name (_S0W, 4)
Name (_PRW, Package () { 5, 3 })
Method (_STA) { Return (0x0f) }
Name (_CRS, ResourceTemplate () {
I2cSerialBus (0x15, ControllerInitiated, 400000, AddressingMode7Bit,
"\\_S.PCI0.I2C1", 0, ResourceConsumer)
Interrupt (ResourceConsumer, Edge, ActiveLow) { 51 }
})
}
}
Change-Id: Ib32055720835b70e91ede5e4028ecd91894d70d5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15016
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Intel WiFi devices that support wake-on-wifi need to declare a Power
Resource for this wake pin. Typically this has been done with a
static declaration in the DSDT for each mainboard. By adding it to
the existing intel/wifi driver it can be done based on a
configuration register in the devicetree.
Additionally the WiFi regulatory domain can be set in the SSDT
directly instead of needing to use NVS to pass the value to the DSDT.
Also add device IDs for Wilkins Peak 2 and Stone Peak 2 devices that
are found on Chromebooks, and clean up a long line and some comment
formatting.
This was tested by booting on an HP Chromebook 13 device and comparing
that the output in the SSDT matches what used to be in the DSDT. The
WRDD value is read from VPD, if present, not from devicetree.cb.
Additionally the case where CONFIG_DRIVERS_INTEL_WIFI is enabled but
the wifi device is not described in devicetree.cb is tested to ensure
it still generates the AML but does not include the _PRW wake pin.
Example:
devicetree.cb:
device pci 1c.0 on
chip drivers/intel/wifi
register "wake" = "GPE0_DW0_16"
device pci 00.0 on end
end
end
VPD:
"region"="us"
SSDT.dsl:
Scope (\_SB.PCI0.RP01) {
Device (WIFI) {
Name (_UID, Zero)
Name (_DDN, "Intel WiFi")
Name (_ADR, 0x00000000)
Name (_PRW, Package () { 16, 3 })
Name (WRDD, Package () {
Zero,
Package () {
0x00000007,
0x00004150
}
})
}
}
Change-Id: I8b5c916f1a04742507dc1ecc9a20c19d3822b18c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15019
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a universal hybrid graphics driver compatible with
all supported lenovo devices.
Hybrid graphics allows to connect the display panel to
either of one GPUs.
As there are only two GPUs one GPIO needs to be toggled.
In case the discrete GPU is activated the panel is routed to it.
On deactivation the panel is routed to the integrated
GPU.
On lenovo laptops the dGPU is always connected to PEG10 and it is
save to disable the PEG slot on dGPU deactivation.
Use common gpio.c for southbridge I82801IX.
Tested on Lenovo T520 using Nvidia NVS 5200m.
Removed Lenovo T430s from the list of supported devices,
as the T430s only supports "muxless Optimus".
Depends on change id:
Iccc6d254bafb927b6470704cec7c9dd7528e2c68
Ibb54c03fd83a529d1ceccfb2c33190e7d42224d8
I8bd981c4696c174152cf41caefa6c083650d283a
Iaf0c2f941f2625a5547f9cba79da1b173da6f295
I994114734fa931926c34ed04305cddfbeb429b62
Change-Id: I9b80b31a7749bdf893ed3b772a6505c9f29a56d1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12896
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
|
|
The Nuvoton NAU8825 audio codec is an I2C device that has a number of
tunable parameters that can be provided to the kernel device driver for
basic configuration and optimal operation.
The configuration options are exposed to devicetree as registers and then
presented as Device Properties via ACPI to the operation system.
This sample configuration in devicetree:
device pci 19.2 on
chip drivers/i2c/nau8825
register "irq" = "IRQ_LEVEL_LOW(GPP_F10_IRQ)"
register "jkdet_enable" = "1"
register "sar_threshold_num" = "2"
register "sar_threshold[0]" = "0x0c"
register "sar_threshold[1]" = "0x1c"
device i2c 1a on end
end
end
Will generate the following code in the SSDT, trimmed for this commit
message as there are more properties that can be configured:
Scope (\_SB.PCI0.I2C4)
{
Name (_HID, "10508825")
Name (_UID, Zero)
Name (_DDN, "Nuvoton NAU8825 Codec")
Method (_STA) { Return (0xF) }
Name (_CRS, ResourceTemplate () {
I2cSerialBus (0x1A, ControllerInitiated, 0x61A80, AddressingMode7Bit,
"\_SB.PCI0.I2C4", 0, ResourceConsumer)
Interrupt (ResourceConsumer, Level, ActiveLow) { 0x3A }
})
Name (_DSD, Package () {
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bff4aa301"),
Package () {
Package () { "nuvoton,jkdet-enable", 1 },
Package () { "nuvoton,sar-threshold-num", 2 },
Package () { "nuvoton,sar-threshold", Package () { 0x0c, 0x1c } }
}
})
}
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I480d72daf5ac3dded9b1cbb5fbc737b9dfde3834
Reviewed-on: https://review.coreboot.org/15015
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ib39e828c6e3145957ecc2dacc1f72de793165514
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/15020
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
One thing that is vital to this patch is the MAC address setting
in case the EEPROM/efuse is unconfigured.
Linux now recognises the default MAC address on GA-G41M-ES2L which
does rely on the default bios settings for the MAC address.
Change-Id: I32e070b545b4c6369686a7087b7ff838d00764e3
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/14927
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Items under DEVICE_SPECIFIC_OPTIONS got selected without
the driver being selected.
Change-Id: I1797fa6175620a9291873559a6308eaea85a090e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14823
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
By design, FSP will send POST codes to port 80. In this case we have
both coreboot and FSP pushing post codes, which may make debugging
harder. In order to get a clear picture of where FSP execution begins
and ends, send post codes before and after any call to the FSP blobs.
Note that sending a post code both before and after is mostly useful
on chromeec enabled boards, where the EC console will provide a
historic list of post codes.
Change-Id: Icfd22b4f6d9e91b01138f97efd711d9204028eb1
Signed-off-by: Alexandru Gagniuc <alexandrux.gagniuc@intel.com>
Reviewed-on: https://review.coreboot.org/14951
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add recipes that insert FSP blobs into CBFS and get rid of
CBFS names hardcoding.
Change-Id: I350abeffc4d23e45e339464d036716ecdb2ba83a
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Simplify the union references to enable Coverity to properly process
the routine.
Found-by: Coverify CID 1349854
TEST=Build and run on Galileo Gen2
Change-Id: I667b9bc5fcde7f68cb9b4c8fa85601998e5c81ff
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14870
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Coverity does not like the use of for/break, switch to using returns
instead.
Found-by: Coverity CID 1349855
TEST=Build and run on Galileo Gen2
Change-Id: I4e5767b09faefa275dd32d3b76dda063f7c22f6f
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14869
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Don't allow an array index of 2 to be processed by the code referencing
the array.
Found-by: Coverity CID 1353337
TEST=None
Change-Id: I586ca14416a6e40971f8f6f4066fbdb4908ca688
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14868
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I384cef0f5b4b71dbd7ad6d1d508e7c6395bf3f2d
Signed-off-by: Alexandru Gagniuc <alexandrux.gagniuc@intel.com>
Reviewed-on: https://review.coreboot.org/14759
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
FSP 2.0 uses the same relocate logic as FSP 1.1. Thus, rename
fsp1_1_relocate to more generic fsp_component_relocate that can be
used by cbfstool to relocate either FSP 1.1 or FSP 2.0
components. Allow FSP1.1 driver to still call fsp1_1_relocate which
acts as a wrapper for fsp_component_relocate.
Change-Id: I14a6efde4d86a340663422aff5ee82175362d1b0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/14749
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Currently, convert_fsp assumes that the component is always XIP. This
is no longer true with FSP 2.0 and Apollolake platform. Thus, add the
option -y|--xip for FSP which will allow the caller to mention whether
the FSP component being added is XIP or not. Add this option to
Makefiles of current FSP drivers (fsp1_0 and fsp1_1).
Change-Id: I1e41d0902bb32afaf116bb457dd9265a5bcd8779
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/14748
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Allow the platform to override the input clock for the UART by
implementing the routine uart_platform_refclk and setting the Kconfig
value UART_OVERRIDE_REFCLK. Provide a default uart_platform_refclk
routine which is disabled when UART_OVERRIDE_REFCLK is selected. This
works around ROMCC not supporting weak routines.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file:
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Build EDK2 CorebootPayloadPkg/CorebootPayloadPkgIa32.dsc to generate
UEFIPAYLOAD.fd
* Testing is successful when CorebootPayloadPkg is able to properly
initialize the serial port without using built-in values.
Change-Id: If4afc45a828e5ba935fecb6d95b239625e912d14
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14612
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Allow the platform to override the input clock divider by adding the
uart_input_clock_divider routine. This routine combines the baud-rate
oversample divider with any other input clock divider. The default
routine returns 16 which is the standard baud-rate oversampling value.
A platform may override this default "weak" routine by providing a new
routine and selecting UART_OVERRIDE_INPUT_CLOCK_DIVIDER. This works
around ROMCC not supporting weak routines.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file:
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Build EDK2 CorebootPayloadPkg/CorebootPayloadPkgIa32.dsc to generate
UEFIPAYLOAD.fd
* Testing is successful when CorebootPayloadPkg is able to properly
initialize the serial port without using built-in values.
Change-Id: Ieb6453b045d84702b8f730988d0fed9f253f63e2
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14611
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Extend the serial port description to include the input clock frequency
and a payload specific value.
Without the input frequency it is impossible for the payload to compute
the baud-rate divisor without making an assumption about the frequency.
This breaks down when the UART is able to support multiple input clock
frequencies.
Add the UART_PCI_ADDR Kconfig value to specify the unique PCI device
being used as the console UART. Specify this value as zero when the
UART is not on the PCI bus. Otherwise specify the device using bus,
device and function along with setting the valid bit.
Currently the only payload to consume these new fields is the EDK-II
CorebootPayloadPkg.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file:
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Build EDK2 CorebootPayloadPkg/CorebootPayloadPkgIa32.dsc to generate
UEFIPAYLOAD.fd
* Testing is successful when CorebootPayloadPkg is able to properly
initialize the serial port without using built-in values.
Change-Id: Id4b4455bbf9583f0d66c315d38c493a81fd852a8
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14609
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=chrome-os-partner:49249
TEST=None. Initial code not sure if it will even compile
BRANCH=none
Change-Id: Ifde289ec004f5d54d5df32011c87e49470e2bb5d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 613b5ae45f7b8325863d8be492a451e6d076e293
Original-Change-Id: I93386e058a60b5c9b61d89607cf8c6e0de6a21ca
Original-Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/334522
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: https://review.coreboot.org/14666
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Before multi-CBFS support was added, x86 platforms cached their
ramstage in TSEG so that it could be re-used on the resume
path. However, more resources/assets are being put in cbfs that are
utilized during ramstage. Just caching ramstage does not mean that
correct cbfs region is used for all the data. Thus, provide an option
to allow platforms to skip caching any component for resume.
Change-Id: I0e957a6b859cc7d700aaff67209a17c6558be5de
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/14636
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
decode_edid either gets EDID_LENGTH bytes or (in the extended case),
2*EDID_LENGTH.
See that this is reflected in its size argument.
Change-Id: If6c76358db4e9ee01c2bd2dbdd5948c61b7aa5bc
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14698
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Due to missing braces (that went undetected because of the
indentation), I584189d9fcf7c9b831d9c020ee7ed59bb5ae08e8
CMOS: add set_option() only takes the last changed byte into regard
when determining whether the checksum needs to be updated.
This bug went undetected for 5 years.
Change-Id: I47cedc801a60959386dfdcda3a13b8e3162a7ecb
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14616
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Recent FSP draft slightly changed FSP_INFO_HEADER structure. This
change keeps FSP driver code in sync with header changes.
Change-Id: I3536f766a312b9eb73ab8940d91dc9b9dfa347f1
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14614
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Reorder drivers to fit src/drivers/[X]/[Y]/ scheme to make
them pluggable.
Change-Id: Idae5ee5f1f48d904b704abe618165c0bec839979
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14048
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The MRC cache API has absolutely no reason to modify the data it is
asked to stash. Reflect that by taking all "data" parameters as
const void *.
Change-Id: I7a14ffd7d5726aa9aa5db81df82c06e7f87b9d9f
Signed-off-by: Alexandru Gagniuc <alexandrux.gagniuc@intel.com>
Reviewed-on: https://review.coreboot.org/14250
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
|
