summaryrefslogtreecommitdiff
path: root/src/include/device
AgeCommit message (Collapse)Author
2021-03-15pciexp_device: Rewrite LTR configurationNico Huber
I was bugged by spurious "Failed to enable LTR" messages for years. Looking at the the current algorithm, it is flawed in multiple ways: * It looks like the author didn't know they implemented a recursive algorithm (pciexp_enable_ltr()) inside another recursive algorithm (pciexp_scan_bridge()). Thus, at every tree level, everything is run again for the whole sub- tree. * LTR is enabled no matter if `.set_ltr_max_latencies` is implemented or not. Leaving the endpoints' LTR settings at 0: They are told to always report zero tolerance. In theory, depending on the root-complex implementation, this may result in higher power consumption than without LTR messages. * `.set_ltr_max_latencies` is only considered for the direct parent of a device. Thus, even with it implemented, an endpoint below a (non-root) bridge may suffer from the 0 settings as described above. * Due to the double-recursive nature, LTR is enabled starting with the endpoints, then moving up the tree, while the PCIe spec tells us to do it in the exact opposite order. With the current implementation of pciexp_scan_bridge(), it is hard to hook anything in that runs for each device from top to bottom. So the proposed solution still adds some redundancy: First, for every device that uses pciexp_scan_bus(), we enable LTR if possible (see below). Then, when returning from the bus- scanning recursion, we enable LTR for every device and configure the maximum latencies (if supported). The latter runs again on all bridges, because it's hard to know if pciexp_scan_bus() was used for them. When to enable LTR: * For all devices that implement `.set_ltr_max_latencies`. * For all devices below a bridge that has it enabled already. Change-Id: I2c5b8658f1fc8cec15e8b0824464c6fc9bee7e0e Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/51328 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-03-14device/pciexp_device.c: Remove CPP guardingArthur Heymans
Let the linker do its job. This fixes building with !CONFIG_PCIEXP_HOTPLUG on some platforms. Change-Id: I46560722dcb5f1d902709e40b714ef092515b164 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/51417 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de>
2021-03-12pci_def.h: Introduce PCI_EXP_DEVCAP2 & PCI_EXP_DEVCTL2 properNico Huber
Replace the existing, odd looking, unordered definitions used for LTR configuration with the usual names used by upstream libpci. TEST=Built google/brya0 with BUILD_TIMELESS=1: no changes. Fixes: Code looked like UEFI copy-pasta. Header file was a mess. Change-Id: Icf666692e22730e1bdf4bcdada433b3219af568a Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/51327 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-03-12device: Give `pci_ops.set_L1_ss_latency` a proper nameNico Huber
Rename `set_L1_ss_latency` to what it does: `set_ltr_max_latencies`. TEST=Built google/brya0 with BUILD_TIMELESS=1: no changes. Change-Id: I7008aa18bf80d6709dce1b2d3bfbb5ea407a0574 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/51326 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-03-12soc/intel/*: drop UART pad configuration from common codeMichael Niewöhner
UART pad configuration should not be done in common code, because that may cause short circuits, when the user sets a wrong UART index. Since all boards do pad setup on their own now, finally drop the pad configuration from SoC common code. Change-Id: Id03719eb8bd0414083148471ed05dea62a895126 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48829 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Lance Zhao
2021-03-11soc/intel/common/block: Add PCI IDs for EmmitsBurg PCHJonathan Zhang
According to Intel EmmitsBurg EDS, doc# 606161: * Add PCI devid for SPI. * Add PCI devid for ESPI (LPC). EmmitsBurg (EBG) PCH is used in the chipset with Sapphire Rapids Scalable Processor (SPR-SP). Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com> Signed-off-by: Subrata Banik <subrata.banik@intel.com> Signed-off-by: Jonathan Zhang <jonzhang@fb.com> Change-Id: Ie8925cb739c95c34febf9002149de437d19c8234 Reviewed-on: https://review.coreboot.org/c/coreboot/+/51321 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-03-05soc/intel/broadwell/pch: Use Lynx Point smbus.cAngel Pons
Continue unifying Lynx Point and Wildcat Point (PCH for Broadwell) code. Define the WPT-LP SMBus PCI device ID, add it to smbus.c of Lynx Point, and drop all now-unnecessary SMBus code from Broadwell. Change-Id: I864d7c2dd47895a3c559e2f1219425cda9fd0c17 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/51235 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-02-27drivers/soundwire/alc1308 : Add ALC1308 soundwire deviceAnil Kumar
This patch adds new soundwire device ALC1308 The codec properties are filled out as best as possible with the datasheet as a reference. The ACPI address for the codec is calculated with the information in the codec driver combined with the devicetree.cb hierarchy where the link and unique IDs are extracted from the device path. The unique ID is calculated from schematics by referring to ASEL[1:0] strap settings. Datasheet of ALC1308 provides info about the mapping of ASEL strap settings to unique ID For example this device is connected to master link ID 1 and has strap settings configuring it for unique ID 2. chip drivers/soundwire/alc1308 register "desc" = ""Left Speaker"" device generic 1.2 on end end Bug=None Test=Build and boot on TGLRVP.Extract SSDT and confirm that the entries for PCI0.HDAS.SNDW are present for ALC1308 Test speaker out functionality Signed-off-by: Anil Kumar <anil.kumar.k@intel.com> Change-Id: Ibf3f1d5c6881cbd106e96ad1ff17ca216aa272ac Reviewed-on: https://review.coreboot.org/c/coreboot/+/51042 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Sathyanarayana Nujella Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-27sb/intel/ibexpeak: Add all PCI IDs for LPCAngel Pons
Taken from document 322170-028 (5 series specification update). Tested on out-of-tree HP ProBook 6550b (HM57), fixes several issues. Without this patch, EHCI controllers had no IRQ assigned and there were unexpected exceptions about NMIs. With this patch, the issues are gone. Change-Id: Icd31dd89ba49e38a5e4c108a8361dbf636332ab8 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/51066 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-24soc/amd/picasso/data_fabric: add missing data fabric device function 7Felix Held
The device function is missing in the PCI device table in the PPR, but is present in the hardware. Verified on a Mandolin board with PCO APU. The corresponding ticket for the PPR is DESPCSOC-6667. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: Ie91438bc905691d443ca4e7841549d1e3bca39ca Reviewed-on: https://review.coreboot.org/c/coreboot/+/51041 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2021-02-24device/device.c: Rename .disable to .vga_disableArthur Heymans
This makes it clear what this function pointer is used for. Change-Id: I2090e164edee513e05a9409d6c7d18c2cdeb8662 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/51009 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-16device/dram: Move SPD manufacturer names out of arch/x86Patrick Rudolph
Move SPD manufacturer ID decoding to device/dram. Will be used by the following patch outside of SMBIOS scope as well. Change-Id: Iec175cd6ab1d20761da955785e4bc0e87ae02dbb Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50544 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-10device/azalia_device: Add mainboard hook to program codecsAngel Pons
On some mainboards, codec configuration depends on settings that are only known at runtime, which is impossible to specify using one verb table. Add an optional `mainboard_azalia_program_runtime_verbs` hook where mainboards can program runtime-dependent codec verbs. Change-Id: I7efeba5c26051aeb5061cce191ace08c304a6c70 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50388 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2021-02-10device/azalia_device: Add function to program a verb tableAngel Pons
On some boards, Azalia configuration depends on config settings that are not known at compile-time. Expose a function to program a verb table, to be used in subsequent commits. Change-Id: Ie9607f6e733df66f0ca26a4bb70e0864ce1d4512 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50387 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2021-02-04drivers/generic/bayhub_lv2: Add driver for BayHub lv2John Su
Add a driver which puts the device into power-saving mode. BUG=b:177955523 BRANCH=zork TEST=boot and see this message: BayHub LV2: Power-saving enabled 110102 Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Change-Id: Idc1340b1a6fe7063d16c8ea16488d6e2b8b308cc Reviewed-on: https://review.coreboot.org/c/coreboot/+/49783 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-03pci_ids/intel: Add missing CFL-S GT1 IGD IDsNico Huber
Change-Id: I372b6b2d602dfe116d5791bb6a6653454523b42b Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50089 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Timofey Komarov <happycorsair@yandex.ru>
2021-02-03pci_ids/intel: Correct 0x3e96, it's a CFL-S partNico Huber
Change-Id: Ibdddb3309f862f52c578e91ba3dc310dff8f70bc Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50088 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Timofey Komarov <happycorsair@yandex.ru> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2021-02-01include/device/pci_ids.h: Add Cannon Lake PCH-H SATA dev IDErik van den Bogaert
Add SATA controller ID for Cannon Lake PCH-H Mobile HALO (see document number: 571182) Add SPDX license header Bug=N/A TEST=Build of Intel Coffeelake H SO-DIMM DDR4 RVP11 successfully completed Change-Id: Ic7e6ace2a24b4278b04caa58be907d38f4d117cd Signed-off-by: Erik van den Bogaert <ebogaert@eltan.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49987 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2021-01-30device: Drop `mmconf_resource_init` functionAngel Pons
All uses of `mmconf_resource_init` have been replaced in previous patches with `mmconf_resource`, which uses Kconfig symbol values. Change-Id: I4473268016ed511aa5c4930a71977e722e34162a Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50112 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2021-01-30device/Kconfig: Introduce MMCONF_LENGTHAngel Pons
This is necessary because ASL Memory32Fixed values cannot contain operations, even if they can be evaluated to constants. Add a sanity check in pci_mmio_cfg.h to ensure consistency with MMCONF_BUS_NUMBER. Change-Id: I8f0b5edf166580cc12c1363d8d6b6ef0f2854be9 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50033 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-22soc/intel/commmon: Include Alder Lake device IDsVarshit Pandya
Add Alder Lake M specific CPU, System AGent, PCH (Alder Point aka ADP), IGD device IDs. Document Number: 619501, 626817 Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com> Change-Id: Ib13fe229f9e65eae8967aa20e28e29ac5c319265 Reviewed-on: https://review.coreboot.org/c/coreboot/+/49629 Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-12device: Use __pci_0_00_0_config in config_of_soc()Furquan Shaikh
This change updates the definition of config_of_soc() to a macro that expands to __pci_0_00_0_config instead of accessing the config structure by referencing the struct device. This allows linker to optimize out unused portions of the device tree from early stages. With this change, bootblock .text section size drops as follows: Platform | Size without change | Size with change | Reduction | ---------------|---------------------|------------------|-------------| GLK (ampton) | 27112 bytes | 9832 bytes | 17280 bytes | APL (reef) | 26488 bytes | 17528 bytes | 8960 bytes | TGL (volteer2) | 47760 bytes | 21648 bytes | 26112 bytes | CML (hatch) | 40616 bytes | 22792 bytes | 17824 bytes | JSL (waddledee)| 37872 bytes | 19408 bytes | 18464 bytes | KBL (soraka) | 31840 bytes | 21568 bytes | 10272 bytes | As static.h is now included in device.h which gets pulled in during the unit tests, a dummy static.h is added under tests/include. Change-Id: I1fbf5b9817065e967e46188739978a1cc96c2c7e Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49215 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Nico Huber <nico.h@gmx.de>
2021-01-12soc/intel/alderlake: Add PCH ID 0x5182Subrata Banik
TEST=Able to build and boot ADLRVP. Change-Id: Ia331998b46abcf10e939078dea992589f09139bd Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49301 Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-12-28device/pnp: add register PNP_IO4Michael Niewöhner
Add the register PNP_IO4, which will be used by IT5570E in CB:48894. Change-Id: Ic820295247323f546d4c48ed17cfa4eab3dc5e92 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48924 Reviewed-by: Felix Singer <felixsinger@posteo.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-12-28device + util/sconfig: introduce new device `gpio`Michael Niewöhner
Introduce a new device `gpio` that is going to be used for generic abstraction of gpio operations in the devicetree. The general idea behind this is that every chip can have gpios that shall be accessible in a very generic way by any driver through the devicetree. The chip that implements the chip-specific gpio operations has to assign them to the generic device operations struct, which then gets assigned to the gpio device during device probing. See CB:48583 for how this gets done for the SoCs using intelblocks/gpio. The gpio device then can be added to the devicetree with an alias name like in the following example: chip soc/whateverlake device gpio 0 alias soc_gpio on end ... end Any driver that requires access to this gpio device needs to have a device pointer (or multiple) and an option for specifying the gpio to be used in its chip config like this: struct drivers_ipmi_config { ... DEVTREE_CONST struct device *gpio_dev; u16 post_complete_gpio; ... }; The device `soc_gpio` can then be linked to the chip driver's `gpio_dev` above by using the syntax `use ... as ...`, which was introduced in commit 8e1ea52: chip drivers/ipmi use soc_gpio as gpio_dev register "bmc_jumper_gpio" = "GPP_D22" ... end The IPMI driver can then use the generic gpio operations without any knowlege of the chip's specifics: unsigned int gpio_val; const struct gpio_operations *gpio_ops; gpio_ops = dev_get_gpio_ops(conf->gpio_dev); gpio_val = gpio_ops->get(conf->bmc_jumper_gpio); For a full example have a look at CB:48096 and CB:48095. This change adds the new device type to sconfig and adds generic gpio operations to the `device_operations` struct. Also, a helper for getting the gpio operations from a device after checking them for NULL pointers gets added. Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with CB:48711 and OCP DeltaLake with CB:48672. Change-Id: Ic4572ad8b37bd1afd2fb213b2c67fb8aec536786 Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com> Tested-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: Patrick Rudolph <siro@das-labor.org> Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48582 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2020-12-17device/azalia_device.c: Add codec reset helpersAngel Pons
Many uses of `azalia_set_bits` are used to toggle the reset bit. To avoid having to repeat the register operations and the corresponding comment, create two helpers with self-explanatory names. They will be put to use in subsequent commits, with one change for each function. Change-Id: If0594fdaf99319f08a2e272cd37958f0f216e654 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48355 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2020-12-17azalia: Make `azalia_find_verb` parametricAngel Pons
Allow to specify which table should the verb list be read from. Change-Id: Id1bc40c4364cda848f416bad9eeab1b8ca3e9512 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48350 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2020-12-17azalia: Drop unused parameter from `azalia_find_verb`Angel Pons
The `dev` parameter isn't used anywhere. Change-Id: I05643f8201137ffe89ded1e3f989c5a0f04e0af1 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48349 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2020-12-17azalia: Make `find_verb` function non-staticAngel Pons
To allow dropping copies of this function, make it non-static. Also, rename it to `azalia_find_verb` as the function is now globally visible. Finally, replace the copies in chipset code with `azalia_find_verb`. Change-Id: Ie66323b2c62139e86d3d7e003f6653a3def7b5f2 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48348 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2020-12-17azalia: Make `set_bits` function non-staticAngel Pons
There's many copies of this function in the tree. Make the copy in azalia_device.c non-static and rename it to `azalia_set_bits`, then replace all other copies with it. Since azalia_device.c is only built when AZALIA_PLUGIN_SUPPORT is selected, select it where necessary. This has the side-effect of building hda_verb.c from the mainboard directory. If this patch happens to break audio on a mainboard, it's because its hda_verb.c was always wrong but wasn't being compiled. Change-Id: Iff3520131ec7bc8554612969e3a2fe9cdbc9305e Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48346 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2020-12-14intel/common/block/lpc: Add new device IDs for Emmitsburg PCHJonathan Zhang
Add LPC/eSPI device ID of Emmitsburg (EMB) for setting LPC resources. Refer to Emmitsburg PCH EDS (606161). Signed-off-by: Jonathan Zhang <jonzhang@fb.com> Change-Id: Ie5a5d9ba7e4f664ada2dae2294d6e4d0280a2157 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48596 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-12-06include/device/device: add comment that config_of_soc never returns NULLFelix Held
Since config_of() calls die() if dev or dev->chip_info are NULL, config_of_soc() will either return a non-NULL pointer or won't return. Change-Id: I6de6bb1610e823af215436c94ff1a78ff6b86b78 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48359 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
2020-12-05device/pci_id: Add TCSS PCI IDs for AlderlakeV Sowmya
Add the PCI IDs for Alderlake TCSS, * USB xHCI * USB xDCI * TBT DMA * TBT PCIe Change-Id: I28bb310c7b031d2766c9e03dbcbe1c79901a7d87 Signed-off-by: V Sowmya <v.sowmya@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48242 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30include/device/pci_ids.h: Fix device id for gspi2Bora Guvendik
Device ID for "D18:F6 - GSPI #2" shoud be 0xA0FB BUG=none TEST=Boot to OS, verify SSDT Signed-off-by: Selma BENSAID <selma.bensaid@intel.com> Signed-off-by: Bora Guvendik <bora.guvendik@intel.com> Change-Id: I0d814170d24ff1b989eceb1d9ebdf6134df85e2e Reviewed-on: https://review.coreboot.org/c/coreboot/+/48060 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-25device: Drop unused HyperTransport codeAngel Pons
Only two definitions are actually used somewhere, the rest is unused. Change-Id: Iec52d0d47fce6a1ec5455b670824b995a7a34a4c Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47407 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24include/device/pci_ids.h: Add PCI IDs used in Lynxpoint chipsetsFelix Singer
Used documents: - 328904-003 - 329003-003 Change-Id: I95790cda6f7c42a9de57bf5e92eb829ee1807dbe Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47807 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-21include/device/pci_ids: add PCI IDs for new AMD SoCsFelix Held
Change-Id: I0caea5627045b7855e2c5f3cb01d4fa21332788b Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47703 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-19include/device/pci_ids: add model number to ATI GPU and HDA controllerFelix Held
Change-Id: I215058bcb0d53bfec974b8d3721cb4c998fcbee5 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47702 Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-18include/device/pci_ids: add model number to AMD GBE controllerFelix Held
Change-Id: I4499c383e63cd12a0fc11efd94ef396d9ad23789 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47678 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-18include/device/pci_ids: add model number to PCIe port and bus devicesFelix Held
Different models within family 17h have different PCI IDs for their PCIe GPP port and internal bus devices. Change-Id: I386df908ce5451b4484be2a2e4a9018c3d47d030 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47677 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-18include/device/pci_ids: add model number to data fabric devicesFelix Held
Different models within family 17h have different PCI IDs for their data fabric PCI devices. Change-Id: I44f8d32c950710e962dc519495b08c92f357ed20 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47676 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-18include/device/pci_ids: deduplicate AMD family 17h northbridge IDFelix Held
The code uses PCI_DEVICE_ID_AMD_17H_MODEL_101F_NB instead; Change-Id: Ia88550d377643741f78ff068e57d6a2d783306f3 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47675 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-18include/device/pci_ids: use the right device ID for AMD Picasso GPUFelix Held
The code that uses the GPU device ID uses the correct ATI vendor ID, but the description wrongly used AMD as vendor. In the AMD APUs the GPU PCI device and the corresponding audio controller use the ATI PCI vendor ID while all other PCI devices in the SoC use the AMD PCI vendor ID. Also move the two entries in a separate section right below the one they were in. Change-Id: Ia0b5bd4638f5b07c487f223321872563b36337e9 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47674 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-16src: Change bare 'unsigned' to 'unsigned int'Martin Roth
This fixes all of the current code in coreboot/src where a bare unsigned is used incorrectly. A follow-on will fix the comments so that we can enable the unsigned lint checker for src/coreboot. Signed-off-by: Martin Roth <martin@coreboot.org> Change-Id: I37f34a95bb1894e70cd9e076d4b81ebac665eaeb Reviewed-on: https://review.coreboot.org/c/coreboot/+/47482 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-12soc/intel/alderlake: Add PCH ID 0x5181Subrata Banik
List of changes: 1. Add new PCH ID 0x5181 into device/pci_ids.h 2. Update new PCH ID into common lpc.c 3. Add new PCH ID description into report_platform.c TEST=Able to build and boot ADLRVP with new PCH ID. Change-Id: I4343b7343876eb40c2955f6f4dd99d6446852dc0 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47474 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-09device: Move pci_dev_is_wake_source functionTim Wawrzynczak
Move this function to pci_ops.c, which is already included in the smm build. This is required to use this function in elog functionality, which is called from SMM. Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: Ie5583c04366c9a16bc1b00a6892d39eeafe5da49 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47260 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-11-02device: Rework bus master optionFelix Singer
As an intermediate step for CB:45150, add an additional Kconfig option which is used to configure bus mastering for any devices and use PCI_ALLOW_BUS_MASTER to allow coreboot setting the bus mastering bit in general. Change-Id: I33b37a79022007a16e97350db61575b63fa8256b Signed-off-by: Felix Singer <felix.singer@secunet.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45149 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-02wifi: Drop PCI IDs for JfP and HrPFurquan Shaikh
This change drops the PCI IDs for Jefferson Peak and Harrison Peak CNVi modules from wifi/generic drivers as well as pci_ids.h. These IDs actually represent the CNVi WiFi controller PCI IDs and are now supported by intel/common/block/cnvi driver. The only ID that is being dropped without adding support in intel/common/block/cnvi driver is PCI_DEVICE_ID_HrP_6SERIES_WIFI(0x2720) since this was not found in the list of PCI IDs for any SoC. Change-Id: I82857a737b65a6baa94fb3c2588fe723412a7830 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46866 Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-02pci_ids: Add PCI IDs for CNVi WiFi/BT controllersFurquan Shaikh
This change adds PCI IDs for CNVi WiFi/BT controllers for CML, GLK, ICL, JSL and TGL. Change-Id: Id45f65d0ef5a7782c08ddd70eb22b26072c8ef4b Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46863 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2020-10-30drivers/soundwire/alc711: Add Realtek ALC711 soundwire deviceAnil Kumar
Bug=None Test=Enabled the device on TGLY RVP and tested that the codec is reflected in SSDT. Checked sound card binding works and soundwire drivers are enabled in kernel. Signed-off-by: Anil Kumar <anil.kumar.k@intel.com> Change-Id: Ia7358927fe8531e609ebe070bef259a2bbc09093 Reviewed-on: https://review.coreboot.org/c/coreboot/+/46303 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-31 23:54:58 +0000