| Age | Commit message (Collapse) | Author |
|---|
|
W83627DHG:
- Add proper "virtual LDN" handling for the LDNs that need it (i.e., those
that don't have their "enable" bit in bit 0 of the 0x30 register).
- Fix various I/O masks in the pnp_dev_info[] array as per
datasheet. Add missing PNP_IRQ0 to the W83627DHG_ACPI LDN.
W83627EHG:
- Similar to W83627DHG, improve the "virtual LDN" setup a bit (it was
mostly implemented already, though).
- Add missing PNP_IRQ0 to the W83627EHG_ACPI LDN.
Also: Fix up devicetree.cb of all boards using W83627DHG/W83627EHG to adapt
for the virtual LDNs.
include/device/pnp.h: Add comment that 'function' (which refers to the
LDN and should probably be renamed later) has to be at least 16 bits
wide. In theory LDNs could use u8, but due to the virtual LDN info being
encoded in the "high byte" of 'function' it must be at least u16.
asrock/939a785gmh/romstage.c: Drop unused GPIO6_DEV.
ibase/mb899/romstage.c: Use DUMMY_DEV instead of a specific LDN (serial
port 1 in this case) to avoid confusion. The global registers
manipulated there are accessible from any LDN.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6140 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
CONFIG_HAVE_ACPI_RESUME == 1 getting rid of ugly define in romstage.c
2) the patch implements get_cbmem_toc in chipset specific way if defined.
On Intel targets it should be unchanged. On K8T890 the the cbmem_toc is read from NVRAM. Why you ask? Because we cannot do it as on intel, because the framebuffer might be there making it hard to look for it in memory (and remember we need it so early that everying is uncached)
3) The patch removes hardcoded limits for suspend/resume save area (it was 1MB) on intel. Now it computes right numbers itself.
4) it impelements saving the memory during CAR to reserved range in sane way. First the sysinfo area (CAR data) is copied, then the rest after car is disabled (cached copy is used). I changed bit also the the copy of CAR area is now done uncached for target which I feel is more right.
I think I did not change the Intel suspend/resume behaviour but best would be if someone can test it. Please note this patch was unfinished on my drive since ages and it would be very nice to get it in to prevent bit rotten it again.
Now I feel it is done good way and should not break anything. I did a test with abuild and it seems fine.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- VIA VT8235: Do the shift in smbus_read_byte() as all other chipsets do.
- spd.h: Move RC00-RC63 #defines here, they were duplicated in lots of
romstage.c files and lots of spd_addr.h files. Don't even bother for
those spd_addr.h which aren't even actually used, drop them right away.
- Replace various 0x50 hardcoded numbers with DIMM0, 0x51 with DIMM1,
and 0xa0 with (DIMM0 << 1) where appropriate.
- Various debug.c files: Replace SMBUS_MEM_DEVICE_START with DIMM0,
SMBUS_MEM_DEVICE_END with DIMM7, and drop useless SMBUS_MEM_DEVICE_INC.
- VIA VX800: Drop unused SMBUS_ADDR_CH* #defines.
- VIA VT8623: Do the shift in smbus_read_byte() as all other chipsets do.
Then, replace 0xa0 (which now becomes 0x50) with DIMM0.
- alix1c/romstage.c, alix2d/romstage.c: Adapt to recent bit shift changes.
- Various files: Drop DIMM_SPD_BASE and/or replace it with DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
addressing scheme to match the rest of the tree
(0x50 instead of 0xa0).
abuild tested.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6087 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6085 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
-- When building for UMA, reduce the limit for DRAM below 4GB
from E0000000 to C0000000. This is needed to accomodate the
UMA frame buffer.
-- Correct problem where msr C0010010 bits 21 and 22 (MtrrTom2En
and Tom2ForceMemTypeWB) are not set consistently across cores.
-- Enable TOM2 only if DRAM is present above 4GB.
-- Use AMD Tom2ForceMemTypeWB feature to avoid the need for
variable MTRR ranges above 4GB.
-- Add above4gb flag argument to function x86_setup_var_mtrrs. Clearing
this flag causes x86_setup_var_mtrrs() to omit MTRR ranges for
DRAM above 4GB. AMD systems use this option to conserve MTRRs.
-- Northbridge.c change to deduct UMA memory from DRAM size reported
by ram_resource. This corrects a problem where mtrr.c generates an
unexpected variable MTRR range.
-- Correct problem causing build failure when CONFIG_GFXUMA=1 and
CONFIG_VAR_MTRR_HOLE=0.
-- Reserve the UMA DRAM range for AMD K8 as is already done for AMD
family 10h.
Tested with mahogany on ECS A780G-GM with 2GB and 4GB.
Tested with mahogany_fam10 on ECS A780G-GM with 2GB and 4GB.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Needed to change class from raid to ide so seabios can boot from it.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6061 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
vt8237r_lpc.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6035 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also:
- Improve a few code comments, fix typos, etc.
- Change a few more variable types to u8/u16/u32 etc.
- Make some very long lines fit into 80chars/line.
- Drop a huge duplicated comment, use "@see" to refer to the other one.
- Reduce nesting level a bit by restructuring some code chunks.
- s/Config.lb/devicetree.cb/ in a few places.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6019 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
variant. It also adds additional dev_find_device calls in k8t890_ctrl.c for
subfunctions 3 and 7.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, change the GX2 boards to use it.
Add a processor speed setting function in human readable MHz and remove
the useless and broken PLLMSR settings (the processor speed was hardcoded
to 366MHz in pll_reset.c).
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6011 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, add a copyright header to pll_reset.c.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Whitespace and indentation fixes in various places.
- Fix various typos.
- Use u8, u16 etc. everywhere.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Macros for the register addresses for the MTRR MSRs are already defined
in include/cpu/x86/car.h. This patch uses those macros instead of
creating a second instance of that same data.
I also added a few macros to the amd mtrr.h to make the MSR naming more
consistent.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5942 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The following functions are moved to devices/device_util.c:
- ram_resource()
- tolm_test()
- find_pci_tolm()
There are only two tolm_test() / find_pci_tolm() which differ from the
defaults, one of them can easily be eliminated in a follow-up patch,
maybe even both, but for now keep it simple and only eliminate the majority.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5916 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- move EHCI_BAR and EHCI_DEBUG_OFFSET to Kconfig to be set by USB debug port enabled southbridges
- drop USB debug code includes from romstage.cs and use romstage-srcs in the build system instead
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5911 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This makes the CAR implementations a lot more readable, shorter and
easier to follow, and also reduces the amount of uselessly duplicated code.
For example there are more than 12 open-coded "enable cache" instances
spread all over the place (and 12 "disable cache" ones), multiple
"enable mtrr", "save BIST", "restore BIST", etc. etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5902 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Use some more #defines instead of hard-coding values.
- Merge multiple movl/orl or movl/andl lines into one where possible.
- Add some TODOs in places which seem to have either an incorrect
code or incorrect comment.
- Fix typos: s/for/from/, s/BSC/BSP/, s/size/carsize/.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5890 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The fill_processor_name() function was duplicated in multiple
model_*_init.c files, move it into a new src/cpu/x86/name
directory.
The strcpy() function was also duplicated multiple times, move it
to <string.h> where we already have similar functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5879 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5865 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5862 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
statement to those files that actually need it. This significantly
reduces the number of dependencies, so it's no longer extremely ugly to
specify them manually (see the src/pc80/Makefile.inc portion)
- Add double include guards around option_table.h defines
- Also, drop the AMD DBM690T work around for the issue
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5838 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5830 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5829 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Add missing license headers, or missing (C) lines to various files.
(most are from AMD / Yinghai Lu, based on svn logs)
- src/include/ehci.h was taken from the Linux kernel. Updating it to
the latest version from git HEAD while I'm at it (build-tested with
one board). It also sports some new EHCI 1.1 addendum #defines which
we may or may not need.
This new file also already has a proper GPL header.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5828 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Root cause: After function STOP_CAR_AND_CPU disables cache as
ram, the cache as ram stack can no longer be used. Called
functions must be inlined to avoid stack usage. Also, the
compiler must keep local variables register based and not
allocated them from the stack. With gcc 4.5.0, some functions
declared as inline are not being inlined. This patch forces
these functions to always be inlined by adding the qualifier
__attribute__((always_inline)) to their declaration.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5818 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Juhana Helovuo <juhe@iki.fi>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5806 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5795 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5764 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
to those files that actually need it. This significantly reduces the number of
dependencies, so it's no longer extremely ugly to specify them manually (see
the src/pc80/Makefile.inc portion)
Also, drop the AMD DBM690T work around for the issue.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5762 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5756 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5683 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
board porter: printk should always be available in CAR mode.
Also drop CONFIG_USE_INIT, it's only been selected on one ASROCK board
but it's not been used there. Very odd.
There is one usage of CONFIG_USE_INIT which was always off in
src/cpu/intel/car/cache_as_ram.inc and we have to figure out what to do with
those few lines.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5682 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also clean up gx2def.h and geode_post_code.h a little.
abuild tested and boot tested on a Wyse S50.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5671 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5669 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Cristian Magherusan-Stanciu <cristi.magherusan@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5666 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
(does not fix the cmos.layout race yet)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5660 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5659 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5658 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Edwin Beasant <edwin_beasant@virtensys.com>
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5653 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Always initialize parents before children.
Move s2881 code into a driver.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5633 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the v3 way.
This resolves problems with terminated DRAM modules.
Signed-off-by: Edwin Beasant <edwin_beasant@virtensys.com>
Acked-by: Roland G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5629 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
there is no free list.
Converting resource arrays to lists reduced the size of each device
struct from 1092 to 228 bytes.
Converting link arrays to lists reduced the size of each device struct
from 228 to 68 bytes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5626 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5621 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5620 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Marc Bertens <mbertens@xs4all.nl>
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Marc Bertens <mbertens@xs4all.nl>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5609 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
coreboot is direct. This patch does it.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5586 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
