Age | Commit message (Collapse) | Author |
|
The gpio table is only used by depthcharge, and depthcharge rarely
has a need for the "recovery" gpio. On a few boards it does use the
gpio as a signal for confirming physical presence, so on that boards
we'll advertise the board as "presence".
All these strings probably should have been #defines to help avoid
typos (e.g., the "ec_in_rw" in stout seems questionable since everybody
else uses "EC in RW").
Cq-Depend: chromium:1580454
BUG=b:129471321
BRANCH=None
TEST=Local compile and flash (with corresponding changes to depthcharge)
to 2 systems, one with a "presence" gpio and another without. Confirmed
that both systems could enter dev mode.
Change-Id: Id6d62d9e48d3e6646cbc1277ea53f0ca95dd849e
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: Iddba5b03fc554a6edc4b26458d834e47958a6b08
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Guckian
|
|
The "write protect" GPIO's cached value is never actually
read after entering depthcharge. Ensure the value from
get_write_protect_state() is being transferred accurately,
so that we may read this GPIO value in depthcharge without
resampling.
The cached value of the "recovery" GPIO is read only on certain
boards which have a physical recovery switch. Correct some of
the values sent to boards which presumably never read the
previously incorrect value. Most of these inaccuracies are from
non-inverted values on ACTIVE_LOW GPIOs.
BUG=b:124141368, b:124192753, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic17a98768703d7098480a9233b752fe5b201bd51
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The dead_code() macro can be used to ensure that a certain code path is
compile-time eliminated (e.g. if you want to make sure it's never
executed for certain Kconfig combinations). Unfortunately, the current
implementation via __attribute__((error)) hits only at the GCC level.
This can catch code that can be compile-time eliminated based on state
within the same file, but it cannot be used in cases where a certain
library function is built but then garbage collected at link time.
This patch improves the macro by relying solely on the linker finding an
undefined reference. Unfortunately this makes the error message a little
less expressive (can no longer pass a custom string), but it is still
readable and one can add code comments next to the assertion to
elaborate further if necessary
Change-Id: I63399dc484e2150d8c027bc0256d9285e471f7cc
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32113
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch is a raw application of
find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
For Chrome OS (or vboot), The PRESERVE flags should be applied on
following sections:
RO_PRESERVE, RO_VPD, RW_PRESERVE, RW_ELOG, RW_NVRAM, RW_SMMSTORE,
RW_VPD, RO_FSG (b:116326638), SI_GBE (chromium:936768),
SI_PDR (chromium:936768)
With the new PRESERVE flag, we don't need RO_PRESERVE and RW_PRESERVE in
the future. But it's still no harm to use it if there are multiple
sections all needing to be preserved.
BUG=chromium:936768
TEST=Builds google/eve and google/kukui inside Chrome OS source tree.
Also boots successfully on eve and kukui devices.
Change-Id: I6664ae3d955001ed14374e2788d400ba5fb9b7f8
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
MMIO operations are arch-agnostic so the include
path should not be arch/.
Change-Id: I0fd70f5aeca02e98e96b980c3aca0819f5c44b98
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31691
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I91158452680586ac676ea11c8589062880a31f91
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31692
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When <symbols.h> was first introduced, it only declared a handful of
regions and we didn't expect that too many architectures and platforms
would need to add their own later. However, our amount of platforms has
greatly expanded since, and with them the need for more special memory
regions. The amount of code duplication is starting to get unsightly,
and platforms keep defining their own <soc/symbols.h> files that need
this as well.
This patch adds another macro to cut down the definition boilerplate.
Unfortunately, macros cannot define other macros when they're called, so
referring to region sizes as _name_size doesn't work anymore. This patch
replaces the scheme with REGION_SIZE(name).
Not touching the regions in the x86-specific <arch/symbols.h> yet since
they don't follow the standard _region/_eregion naming scheme. They can
be converted later if desired.
Change-Id: I44727d77d1de75882c72a94f29bd7e2c27741dd8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The dependencies of CONSOLE_SERIAL and DRIVERS_UART were somehow
backwards. Fix that. Now, CONSOLE_SERIAL depends on DRIVERS_UART,
because it's using its interface. The individual UART drivers
select DRIVERS_UART, because they implement the interface and
depend on the common UART code.
Some guards had to be fixed (using CONSOLE_SERIAL now instead of
DRIVERS_UART). Some other guards that were only about compilation
of units were removed. We want to build test as much as possible,
right?
Change-Id: I0ea73a8909f07202b23c88db93df74cf9dc8abf9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: I3d77a625c5ece7b7ea5476fe0bd42829d1fc72c4
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29625
Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6c77f4289b46646872731ef9c20dc115f0cf876d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Id07e1c7fbd35393ffafda53fc7a15ec0e157d075
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The romstage main() entry point on arm64 boards is usually in mainboard
code, but there are a handful of lines that are always needed in there
and not really mainboard specific (or chipset specific). We keep arguing
every once in a while that this isn't ideal, so rather than arguing any
longer let's just fix it. This patch moves the main() function into arch
code with callbacks that the platform can hook into. (This approach can
probably be expanded onto other architectures, so when that happens this
file should move into src/lib.)
Tested on Cheza and Kevin. I think the approach is straight-forward
enough that we can take this without testing every board. (Note that in
a few cases, this delays some platform-specific calls until after
console_init() and exception_init()... since these functions don't
really take that long, especially if there is no serial console
configured, I don't expect this to cause any issues.)
Change-Id: I7503acafebabed00dfeedb00b1354a26c536f0fe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28199
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Remove 2nd software stack in pc80 drivers directory.
* Create TSPI interface for common usage.
* Refactor TSS / TIS code base.
* Add vendor tss (Cr50) directory.
* Change kconfig options for TPM to TPM1.
* Add user / board configuration with:
* MAINBOARD_HAS_*_TPM # * BUS driver
* MAINBOARD_HAS_TPM1 or MAINBOARD_HAS_TPM2
* Add kconfig TPM user selection (e.g. pluggable TPMs)
* Fix existing headers and function calls.
* Fix vboot for interface usage and antirollback mode.
Change-Id: I7ec277e82a3c20c62a0548a1a2b013e6ce8f5b3f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch enables the new bootblock compression feature on RK3399,
which requires moving MMU initialization into the decompressor stage and
linking the decompressor (rather than the bootblock) into the entry
point jumped to by the masked ROM.
RK3399's masked ROM seems to be using a bitbang SPI driver to load us
(very long pauses between clocking in each byte), with an effective data
rate of about 1Mbit. Bootblock loading time (as measured on a SPI
analyzer) is reduced by almost 100ms (about a third), while the
decompression time is trivial (under 1ms).
Change-Id: I48967ca5bb51cc4481d69dbacb4ca3c6b96cccea
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/26341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use of device_t has been abandoned in ramstage.
Change-Id: I8e549e4222ae2ed6b9c46f81c5b5253e8b227ee8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It's very confusing trying to find the google platform names, because
they seem all unsorted in Kconfig. They're actually sorted according
to the variant name, but previously, that was impossible to tell.
- Add a comment to the top of variants in Kconfig.name
- Inset each variant name. If you start a prompt with whitespace,
it gets ignored, so after trying various ways to indent, the arrow
was the option I thought looked the best.
It now looks like this:
*** Beltino ***
-> Mccloud (Acer Chromebox CXI)
-> Monroe (LG Chromebase 22CV241 & 22CB25S)
-> Panther (ASUS Chromebox CN60)
-> Tricky (Dell Chromebox 3010)
-> Zako (HP Chromebox G1)
Butterfly (HP Pavilion Chromebook 14)
Chell (HP Chromebook 13 G1)
Cheza
*** Cyan ***
Change-Id: I35cb16b040651cd1bd0c4aef98494368ef5ca512
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Generalize cbfs_boot_load_struct() by passing in CBFS type
Change-Id: I6e5f845cb4ce5b00f01a39619919f85e39028f19
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Hardware updates have suggested we need to configure the K&D panel's
power sequence in software, not in hardware. Without this change, K&D
panels will no longer power on correctly and will instead display a
black screen.
Per K&D's suggestion, we tweak these two commands. From the little HW
docs I have, this looks like it's:
(Address 0xB7, Value 0x02) -> set BC_CTRL=bit(1) (Back light control) to
1
(Address 0xF1, Value 0x22) -> change GPO2_SEL=bits(0:3) from
MIPI_TE(0001b) to BC_CTRL (0010b)
BRANCH=scarlet
BUG=b:73133861
TEST=KD display with and without HW fix on Scarlet
Change-Id: Ia076a378b10417dd9891746f9bc1086360a0f6e6
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-on: https://review.coreboot.org/25023
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turns out the write-protect GPIO polarity for Scarlet is different than
for Kevin/Gru, and nobody ever told us. Also, it must not be configured
with an internal pull-up or we'll not read the correct value. This patch
fixes both issues.
BRANCH=scarlet
BUG=b:73356326
TEST=Booted Scarlet, confirmed that crossystem wpsw_boot returns the
right value in all cases.
Change-Id: Idd348ecdf9da8fff7201b83e869ba097b8570f32
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/23767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
With the new extra detachable UI elements, we're running out of space in
Scarlet's RO CBFS. Thankfully, the GBB is still massively
overdimensioned, so we can steal another half MB from there.
This patch changes the FMAP for some boards that have already had
production firmware releases. However, all the new changes are to the RO
parts of the FMAP, so there shouldn't be a way this could cause a
problem for updates.
Change-Id: Iec182de3e894e56fec2a64b034c0ca65d78a5522
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/23595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There is a line artifact in the lower third of the display with the
current initialization code. So update it with code provided by
Innolux to fix this issue.
BUG=b:69689064, b:72191820
TEST=boot on dru with an Innolux panel and artifact line disappear.
Change-Id: I9679c4f7f706fd6cd2e1dba7ec79e772fe3f227a
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Innolux didn't deliver a working init sequence yet for devices without
OTP programming. The sequence in this change has been derived from a
register dump of a mostly working panel with OTP. It is not meant to
be final, but to make devices with unprogrammed OTP work, while Innolux
is figuring out a proper sequence. There is a known issue with an
artifact line in the lower third of the display.
Change-Id: I7096506208e4cb29c5f31a7ac502231a6c23ac92
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Some panels need to transfer initial code, and some of them will be
over 3 bytes, so support LONG_WRITE type in driver. Refactor mipi
dsi transfer function to support it.
Change-Id: I212c14165e074c40a4a1a25140d9e8dfdfba465f
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
* Rename tlcl* to tss* as tpm software stack layer.
* Fix inconsistent naming.
Change-Id: I206dd6a32dbd303a6d4d987e424407ebf5c518fa
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
* Move code from src/lib and src/include into src/security/tpm
* Split TPM TSS 1.2 and 2.0
* Fix header includes
* Add a new directory structure with kconfig and makefile includes
Change-Id: Id15a9aa6bd367560318dfcfd450bf5626ea0ec2b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Rainier, a scarlet derived board, was configured to use spi0 for tpm
driver by default. This patch switches it to spi2 to reflect recent
changes in scarlet-derived boards.
Change-Id: Ib67109786512c068bb957890f456bccff7addc86
Signed-off-by: Ege Mihmanli <egemih@google.com>
Reviewed-on: https://review.coreboot.org/23129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It seems that RAM code 0 has been strapped with an incorrect resistor on
Kevin. The resulting voltage divide still puts it well within the ADC
value bucket reserved for that slot, but a little closer to the edge
than necessary. While this doesn't seem to cause any immediate problems
on its own, it still doesn't hurt to fix it (if only for the
documentation value).
On other boards (at least on my Scarlet) the strapping seems to be
correct.
Change-Id: Ic5199834fbeaf734e725ff45b04f45eefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22891
Reviewed-by: David Schneider <dnschneid@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch shifts some comments around to make it easier to replace
values in the ADC strapping bucket table with compile-time conditionals.
Change-Id: Ic51917d3961a51d4e725ff824fb59aeefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add INNOLUX P097PFG panel timing. According to Scalet schematic,
if GPIO3_D4 get low status, it will use INNOLUX P097PFG panel;
if GPIO3_D4 get high status, it will use KD097d04 panel.
Change-Id: I43fa5d859a9a529a84c58a953b37d03953ce648a
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Due to a schematic error, our code was written to configure more I2S0
pins than are actually used. We're also pinmuxing the whole bank of pins
over to the I2S controller even though we don't need them all. Restrict
the GPIO initialization and pinmuxing to the pins we really need so the
other ones can be correctly used as SKU ID pins on Scarlet.
Also, move the "audio" IO voltage domain selection to the other such
selections in the bootblock, since that covers two whole banks of GPIOs
and there's no guarantee that they're all used for audio (and thus not
needed before ramstage).
BUG=b:69373077
TEST=Booted Scarlet, confirmed correct SKU ID (7) was detected on rev2.
Change-Id: I9314617e725fe83d254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
|
|
These pins need to be pull-ups. I forgot.
BUG=b:69373077
Change-Id: I9314617e01d35898254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the old timing, the hblank time isn't large enough,
it may cause display artifacts. So fix it.
BUG=b:70160653
TEST=panel work on Scarlet rev2 board
Change-Id: Ib061f5e215611d20f59e3f24cfe3c7fbc507ebed
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Scarlet has SKU detection strapping pins now. This patch adds the code
to read them.
BUG=b:69373077
Change-Id: I8d889a845950923bc7b5be9b79792cf3c8b6b8ad
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22697
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch switches the board_id and ram_code helper framework to use
weak functions rather than Kconfigs to determine whether the board
supplies these IDs. This cuts down on the amount of boilerplate Kconfigs
many boards have to set and also gives them more flexibility, such as
being able to determine at runtime whether a given ID is present.
Change-Id: I97d6d1103ebb2a2a7cf1ecfc45709c7e8c1a5cb0
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22695
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Merge the different coreboot table strapping ID structures into one
because they're really just all the same, and I want to add more. Make
the signature of the board_id() function return a uint32_t because
that's also what goes in the coreboot table. Add a printk to the generic
code handling strapping IDs in ramstage so that not every individual
mainboard implementation needs its own print. (In turn, remove one such
print from fsp1_1 code because it's in the way of my next patch.)
Change-Id: Ib9563edf07b623a586a4dc168fe357564c5e68b5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is some confusion with old RAMID table, make it clear,
and let's no longer tangle it in future.
Change-Id: I44215b4a6668074575a5df691ac1ff8fa3d15492
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Support kd097d04 dual mipi panel on Scarlet.
Change-Id: Ie8bc0cbb79840f1924a8cc111f2511292203731f
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
it uses backlight enable pin as backlight gpio currently,
correct it and define the right backlight gpio.
Change-Id: I7c5abfd5bbbae015b899f3edc8892ea32bf82463
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Refactor the mipi driver, so we can support dual mipi panel.
And pass the panel data from mainboard.c, that we can
support different panel with different board.
Change-Id: Id1286c0ccbe50c89514c8daee66439116d3f1ca4
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Rainier is a scarlet-derived board but uses eDP as opposed to MIPI. Using
GRU_BASEBOARD_SCARLET is enough, except for display related logic. In
those cases, use board specific logic instead of baseboard.
Change-Id: I596f7ca6bc26312ecaeb261c96cebd46974c2cdf
Signed-off-by: Ege Mihmanli <egemih@google.com>
Reviewed-on: https://review.coreboot.org/22542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
There is merit in having new boards use the pinouts and controls
in scarlet. This adds a config so new scarlet-derived boards can
easily use scarlet structure without going through every file
and adding new logic.
TEST=Run "emerge-scarlet coreboot"
Signed-off-by: egemih@chromium.org
Change-Id: I5808f93f4563033ce93050e1eedb6eac2b52c3b3
Reviewed-on: https://review.coreboot.org/22517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
It's sometimes hard to find the code name of a Chromebook. Add the
marketing names to Kconfig, since they are easily available.
Information (mostly) taken from:
https://www.chromium.org/chromium-os/developer-information-for-chrome-os-devices
Unknown boards (unreleased, etc.):
* Fizz
* Foster
* Nasher, Coral
* Purin
* Rotor
* Rowan
* Scarlet, Nefario
* Soraka
* Urara
* Veyron_Rialto
Baseboards:
* Glados
* Gru
* Jecht
* Kahlee
* Nyan
* Oak
* Poppy
* Rambi
* Zoombini
White label boards:
* Enguarde
* Heli
* Relm, Wizpig
TODO: How does this interact with the board_status code?
Change-Id: I20a36e23bd3eea8c526a0b3b53cd676cebf9cd86
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On older Grus, GPIO0_A2 was an audio voltage rail enable line. On
Scarlet, we instead moved the audio codec enable (previously on
GPIO1_A2) there. Unfortunately the code still had some hardcoded
leftovers that were overlooked in the initial port and make our speakers
smell weird.
This patch fixes the incorrect GPIO settings and adds the speaker enable
pin to the GPIOs passed through the coreboot table, so that depthcharge
doesn't have to keep its own definition of the pin which may go out of
sync.
Change-Id: I1ac70ee47ebf04b8b92ff17a46cbf5d839421a61
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
RK3399 has a pin that can decide whether GPIO port 1 is driven with 1.8V
or 3.0V. We thought this mechanism was disabled by default, but it turns
out it wasn't. We want to use that pin as an output GPIO on Scarlet so
we need to reconfigure the respective SoC controls before we do that. It
seems that we also need to explicitly pinmux the pin away from that
special function (to normal GPIO) or weird things happen on some boards.
BUG=b:66534913
TEST=Sprinkled several long udelays, poked test points with a
multi-meter on Scarlet.
Change-Id: Ia02cbb4f3b2f14b0d958b84adcddb0c5f4259efa
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/21727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We've decided to move control for the 3.0V rail (technically 3.3V on
Scarlet, but who cares about millivolts) back to a GPIO on the AP for
Scarlet rev2. This patch adds the necessary code to enable it and make
ARM TF aware of its existence. Since the pin had previously not been
connected to anything, we shouldn't really need to guard this by board
ID... older Scarlets will just be twiddling an empty pin.
Change-Id: I6037aa486b50119f2c7b859b966cadc3686e3459
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/21328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
|
|
Do not assert GPIO1_B3 otherwise BT would be disabled on Nefario.
Also, remove DVS support for CENTERLOGIC.
BUG=b:64702054, b:63537905
TEST=build coreboot
Change-Id: I350db2c080f2e41ae56413f5f895557978ef0ba8
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/21176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
some gpio irq need to set input pull initialization status
to guarantee to get the right irq trigger. let's add this argument
in gpio_input_irq() function
BRANCH=None
BUG=None
TEST=boot from bob
Change-Id: I9b8e6497f07146dafdb447a6ea10d039a2a2fa33
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|