Age | Commit message (Collapse) | Author |
|
MEM_CH_SEL is used to indicate whether we are on a single or dual
channel device, where MEM_CH_SEL = 1 for single channel skus and
MEM_CH_SEL = 0 for dual channel skus. Initialize single_channel field
(from GPP_F2), which will in turn initialize MemorySpdPtr pointers in
cannonlake soc code. In the first build, we did not use GPP_F2, so we
need to add an internal pulldown as those early devices were all dual
channel devices.
BUG=b:123062346, b:122959294
BRANCH=None
TEST=Boot into current boards and ensure that we have 2 channels as expected
Also, verify that GPP_F2 is set to 0.
Change-Id: I89d022793580be603a93d0b177d73ce968529b5c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Following changes are done to enable audio support on hatch
1. Enable I2C4 device at 400Khz at 1.8V
2. Configure GPIO for HP INT and SPKR_PA_EN
3. Add ACPI entry for RT5682 and MAX98357A
4. Enable I2S0 and I2S1 lines
5. Enable generic max98357a driver in Kconfig
BUG=b:123738217
BRANCH=none
TEST=Check SSDT table for RT5682 & MAX98357a entry.
Verify audio using Sound Open firmware (SOF)
Change-Id: I93f3917c19cc3f0f8fd7b5e1b4d9b24a59f45f84
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:123490912
BRANCH=None
TEST=flash BIOS and make sure hatch boots up properly
Change-Id: I9e41f0b38703f2c7a2b5a7ac9b108f8f10070004
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31724
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
coreboot did not program all GPIOs from C0 to C7 correctly which are
SMBUS GPIO. Some of the GPIOs are left in default mode which is
native function but we need to configure as GPIO mode and provide proper
configuration as per schematic.
After fixing GPIO, CSME power gating issue also gets fixed since SMBUS was not
getting idle due to GPIO configuration and CSME was not getting power
gated due to SMBUS.
BUG=b:123702553
BRANCH=none
TEST=Check on hatch board. CSME was not getting power gated for s0ix.
After applying this patch CSME is power gated now
Change-Id: I5c6b9310dcc7bade0023abd5524781ce71df28be
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Initialize GPIO_PCH_WP early in boot. Update cros_gpios[] array with
GPIO_PCH_WP information. Also, Configure recovery mode GPIO as virtual
since hatch does not have one.
BUG=b:125943273
Change-Id: I0b7e6dbf9229941aca4952965fb54f07457dccae
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
SD_CD# in Cannonlake PCH is also wired to an internal virtual GPIO,
expose that GPIO for kernel to configure card detect IRQ.
BUG=b:123350329
Change-Id: I566cc2eb11dc257366897a1efba905b8ddcf493d
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
For some reason, wake does not currently work from GPP_D21, but IRQs
are working fine from that gpio. Thus, we have to switch IRQ to
GPP_D21 and wake to GPP_A21, which was previously used for IRQs from
the trackpad. Additionally, we need to use two gpios for irqs and
wake source at the moment because of b:123967687, where FSP is locking
down PCR and configuring ITSS. We need to configure the wake source
gpio as inverted and the IRQ gpio as non-inverted until the bug is
resolved.
BUG=b:121212459
BRANCH=None
TEST=run evtest with trackpad
Use trackpad with ChromeOS UI and make sure it reacts as expected.
Run powerd_dbus_suspend and press trackpad and make sure DUT
wakes.
Change-Id: I7b236136befc05c6586d9ba69185ed4b5d385273
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This implementation configures GPIO (GPP_A21, GPP_C21, GPP_D16)
pad in non-inversion mode i.e Rx PAD state is not inverted as
it is sent from GPIO to IOAPIC.
BUG=b:123315212
TEST=Tested for below:
-> Verify touchpad is working fine.
-> TPM init is successful and boot with fixed boot media.
Change-Id: I6034fd07ccc96a19218d57ef8bb9049c4b963ea5
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/31328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change enables I2C bus 2, 3 and 4 in devicetree and configures
GPIO pads for the same. It also configures pads for I2C5 as
no-connect.
BUG=b:123711244
TEST=Verified that i2c shows up in "i2cdetect -l" after booting to OS.
Change-Id: Ib4714a670d73228332115415e4393f82802c6475
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31237
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initialize EC_PCH_WAKE_ODL GPIO to make sure that ec events will wake
the AP from suspend. Also create a task to initialize the hostevent
wake mask properly.
BUG=b:123325238,b:123325720
BRANCH=None
TEST=from AP console: powerd_dbus_suspend
from EC console: hostevent (make sure wake mask set)
from EC console: gpioset PCH_WAKE_L 0
Make sure device wakes up
Also, checked to make sure keyboard press wakes up
device from S3.
Change-Id: I53d5291a6b9ab9a21e89ccd21f172180ce473bd5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch enables relevant GPIOs to enable WWAN. WWAN also requires to
enable USB 2 port 6 and USB3 port 5 which is already enabled in device
tree related changes.
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I1559bbc6168aec1a369bf3291d2c1e2f9a2fbe07
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable PCIe WLAN for hatch
1. Enable PCI port 14 for PCIe WLAN
2. Enable CLKREQ, CLK SRC 3 for PCI port 14
3. GPIO pad config for WLAN and BT
USB port for BT has already been enabled so not included in this patch
BUG=b:120914069
BRANCH=none
TEST=check if code compiles correctly and verify GPIO configuration with
schematics
Change-Id: I4f2a6eb37a467ad8b8cdde8fe6b657fabb383b04
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Enable support for SD card support for hatch
1. Enable PCI device for SD and also configure SD detect GPIO
2. Configure SD card related GPIOs in gpio.c
BUG=b:120914069
BRANCH=none
TEST=Verify GPIO configuration with schematics
Change-Id: I8ccaa28323b1e1fcc192e245347a96309227660b
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Following changes are done to enable touch screen support on hatch
1. Enable I2C1 device at 400Khz at 3.3V
2. Configure GPIO for touch screen
3. Add ACPI entry for ELAN touch panel
4. update GPIO table with not connected GPIO pins for panel
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I8dab07dad4cb197865bb9cf0e8da240810fcfabe
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This patch enables CNVi wifi for hatch
1. Enable CNVi device in device tree
2. Configure GPIO pad config for CNVi
BUG=b:120914069
BRANCH=none
TEST=check if code compiles correctly and verify GPIO configuration with
schematics
Change-Id: I0c5542737d3a629b6a40116b4aa8ab6cbdd6a4dc
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30436
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correcting order of display related GPIOs and also adding not connected
pin definitions for display GPIOs
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I9498284d263516f65513d6395883b6b09dd70fd5
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This patch enables the x4 NVME device for hatch,
* Enable the Root port 9.
* Assign the usage type for clock source.
* Configure the GPIO for CLK SRC 1.
BUG=b:120914069
BRANCH=none
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot.
Change-Id: I69be6b21a5ae5962877a5c38180b5ffac532fed4
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30431
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the configurations for,
* USB 2.0 ports.
* USB 3.0 ports.
* Enables USB xHCI controller.
* GPIO config for USB2_OC2 and USB2_OC3.
* Add the ACPI objects to configure USB ports.
BUG=b:120914069
BRANCH=none
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot.
Change-Id: Ia7b25c25b8208c678aeae3a32033611b69b54062
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30457
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables the SATA for hatch,
* Enable the SATA port 1.
* Configure the GPIO for SATA.
BUG=b:120914069
BRANCH=none
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot.
Change-Id: Iaf800d1531688c3d3b82600038ea1d7160ae4b0b
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30435
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch incorporates following changes to enable console on UART0
1. update default console number to 0
2. Enable PCI port for UART0
GPIO configuration will be done by coreboot based on correct console
number.
Change-Id: I735d33674b276b28e2cbb753d3a6d83edbabe89d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Adding hot plug detect GPIO support for external Type-C display in event for
cable connect/disconnect.
Change-Id: If9d52dc0f9916f761c8fdd88c76968aaf663e650
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30365
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This implementation adds below support:
1. Add support to read memory strap.
2. Add support to configure below memory parameters
-> rcomp resistor configuration
-> dqs mapping
-> ect and ca vref config
3. Include SPD configuration
BUG=b:120914069
BRANCH=None
TEST=USE="-intel_mrc -bmplk" emerge-hatch coreboot
Change-Id: I9bda08bd0b9f91ebb96b39291e15473492a6bf19
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30248
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:120914069
BRANCH=None
TEST=USE="-intel_mrc" emerge-hatch coreboot
Change-Id: I91db5745d1db16ab4b2fbb7f8c415bd7c1eb29e9
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Incorporating some feedback to initial hatch mainboard checking
(CL:30169) that came in after the CL merged.
Updated the chromeos.fmd with the following,
* SI_ALL = 3MB
* SI_BIOS = 16MB
BUG=b:20914069
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a -v
Change-Id: I4e311c68873f10f71314e44d3a714639a06dbee8
Signed-off-by: Shelley Chen <shchen@google.com>
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30296
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add code support to enable H1 TPM interfaced to SOC on GSPI0.
The TPM interrupt is mapped to GPP_C21.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: Ib63a0b473f632d91745102ebd01993e8d65b9552
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30210
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This implementation cleans up gpio configuration functions
and limit definition to baseboard only for now, until variant
specfic overides are needed.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: I563f6b97812b32d6e3d99e3df512dc112da78aea
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30291
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Creating skeleton files and directories in mainboard for the new Hatch
board. This is to facilitate development for different parties
involved.
BUG=None
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I5fc60c178f83034abe5d846d0f4169072b66f448
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|