Age | Commit message (Collapse) | Author |
|
The firmware_Mosys FAFT test does not allow RW_SECTION_A, RW_SECTION_B or
RW_SHARED to be 0-sized, nor located at offset 0x00000000.
Swap UNIFIED_MRC_CACHE and RW_SECTION_A to pass this test.
BUG=b:79865447
TEST=test_that -b grunt ${IP} firmware_Mosys
Change-Id: If60919fd998ac786d58a5a258d7b5ded727db64b
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Lower the amount of UMA memory to 32MB at AMD's request.
TEST=none
BUG=b:79906569
Change-Id: Ib1365dc38850b4b92c944ff95534573addbe4362
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/26383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Lower the amount of UMA memory to 32MB at AMD's request.
TEST=boot Grunt, try S3
BUG=b:79906569
Change-Id: I5af038688b38b53c94b8265823eeee0f37980522
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/26382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Using da7219 mclk-name property, oscout system clock is linked
to da7219 mclk. da7219 then handles enabling/disabling of the clk.
BUG=b:74570989
TEST=Tested clock enable/disable in kernel driver
Change-Id: I298b0ce5d2c40daadeb5d68f9cb595a965272021
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This reverts commit edf2f59b1d93a1bc9161a67d3c00a9a05fa8519a.
(google/kahlee: Resume on AC insertion)
The requirement to wake on AC insert is just to wake enough to charge,
not to wake the entire system.
BUG=b:77602394
TEST=None
Change-Id: I0ee709183b1605c1efc0fce673db512fac66adfa
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26014
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Add raydium controller
- Update elan controller with reset and enable GPIOs.
- Enable 'probed' so Linux will check which controller is being used.
BUG=b:78929054
TEST=Both elan and raydium touchscreen controllers work
Change-Id: I3bd9912a4b1edc7bf1075cb649afa3eab5dca458
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25998
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable this driver along with power saving.
BUG=b:73726008
BRANCH=none
TEST=boot and see this message:
BayHub BH720: Power-saving enabled 110103
From linux:
$ iotools pci_read32 2 0 0 0x90
0x00110103
Change-Id: I850e923f73e01fe629d66ad61b65afa58035845c
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/25967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add RW_NVRAM area to FMAP for VBOOT_VBNV_CMOS_BACKUP_TO_FLASH support.
BUG=b:77347873
TEST=Manually clear CMOS and check coreboot restores VBNV from flash.
Change-Id: Id8c6f54634b94bf6ae3755a827e80d0862a42dd2
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The grunt touchpad interrupt can be used as a wake source. For grunt,
the touchpad interrupt uses GPIO5 which corresponds to GEVENT7.
BUG=b:77602771
TEST=In OS: # cat /proc/acpi/wakeup
=> D015 S3 *enabled i2c:i2c-ELAN0000:00
TEST=powerd_dbus_suspend, touching touchpad (> 1 sec) wakes from S3.
Change-Id: I510642108a1257f6601f18c77cf3107573427f39
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/25827
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The grunt EC uses GPIO24 (EC_PCH_WAKE_L) to signal wake-up events to the AP.
On Stoney, GPIO24 maps to GEVENT (GPE) 15.
The kahlee EC uses GPIO2 (EC_PCH_WAKE_L) to signal wake-up events to the AP.
On Stoney, GPIO2 maps to GEVENT (GPE) 8.
BUG=b:78461678
TEST=powerd_dbus_suspend, tap any key on keyboard wakes from S3.
TEST=sign in, EC: lidclose, EC: lidopen => system wakes from S3.
Change-Id: Ib1809740837e686992ff70b81933159a5dff7595
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/25816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
On the kahlee variant, EC_SMI_ODL is connected to GPIO6, which uses
GEVENT 10 (GPE10). Fix this up, and also clean up the EC_*_GPI
definition format a bit to match the format in the baseboard/gpio.h.
BUG=b:78461678
TEST=build coreboot for kahlee
Change-Id: I9445efbc02559c2a7c90f67bcb0154b04b03a1aa
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/25826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
When GPIO tables were created, there was no study on which pins had to be
programmed ASAP and which could be programmed later. Execute such study and
move all non-critical gpios from reset to late.
BUG=b:76097508
TEST=Build and boot grunt to OS, test OS for lost functionality (WIFI, video
playback, track pad, keyboard).
Change-Id: Icbc9370050d619800026035caaac3e89536a460a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of writing out '__attribute__((weak))' use a shorter form.
Change-Id: If418a1d55052780077febd2d8f2089021f414b91
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
The GPIO definition structure has evolved to a point where it's no longer
specific to stoneyridge, though probably still specific to AMD. Therefore,
rename the GPIO declaration structure removing stoneyridge from it.
BUG=b:72875858
TEST=Build kahlee, grunt, gardenia.
Change-Id: Ib034d3f7840c36ee8f5c5384241d7326d3fe5543
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25726
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the exception of code that deals directly or indirectly with AGESA,
all other code should be independent of vendor code reference. Therefore,
remove vendor code reference from any GPIO code.
BUG=b:77999987
TEST=Build and boot grunt.
Change-Id: I9ba78767a269ad6b9b06fa11993d8a12350e4bad
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25695
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As part of preparing to make GPIO code independent of vendor code references,
convert GPIO table format using newly defined macros.
BUG=b:77999987
TEST=Build and boot kahlee.
Change-Id: I0af768bb4dbcbfef0d2d08ffe869c1dfb6827974
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The EC code should not have been removed from devicetree when moving
over from grunt. This was causing various bewildering issues that
would happen on the first boot but not on subsequent reboots.
BUG=b:73235377
TEST=Grunt powers off and stays powered off at dev screen.
Change-Id: I225138fede66c6e189e0e79d1261d0d579f7cbdc
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
The EC pin definitions are GPEs, not the GPIO numbers.
BUG=b:74022675
TEST=Power status updates immediately when power is inserted.
Change-Id: Icc8330a606f7a85e72b65094462a684927986829
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25689
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The EC should wake the system from S3 when the AC connector is plugged.
BUG=b:77602394
TEST=verify resume on insert with Grunt
Change-Id: I4bcaef2fe75283aaa6260b5b9efd408ff4b05f4c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/25647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
bt-pad-enable property is used by kernel driver to set
BT I2S PAD on ACP_BT_UART_PAD_SEL mux, for those platforms which
use these pins for BT I2S. By default the pins are set for UART.
BUG=b:72360151
TEST=Tested playback and capture on audio device connected to BT I2S
Change-Id: Id76bfa1fa1dde904f02a03b0c15986ecb1bbcc97
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25653
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn on keyboard backlight in romstage to indicate that the system is
booting.
BUG=b:77921345
TEST=Boot grunt, keyboard backlight comes on.
Change-Id: Ib215b19ebdee2f8c4f431af775905eca42436d1c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25636
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ACPI interrupt routing file routing.asl is not reflecting AGESA settings to
the NB Interrupt Routing Registers. The AGESA settings are:
Device self INTA INTB INTC INTD
GPP 0 23 0 1 2 3
GPP 1 24 8 9 10 11
GPP 2 25 16 17 18 19
GPP 3 26 24 25 26 27
GPP 4 23 3 0 1 2
HDA none 22 23 20 21
GBIF none 6 7 4 5
Fix the routing table, considering that NB IOAPIC starts at interrupt 24.
BUG=b:74104946
TEST=Build and boot to a modified grunt board to enable the emmc. Then used
"cat /proc/interrupts" to get active interrupts. Also checked IOAPIC
redirection registers, which are now being programmed.
Change-Id: I60847c46f3f938f9e97d7b323b27d20e36aa2d02
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Grunt supports a keyboard backlight, so enable the ASL code.
BUG=b:77455525
Test=Boot Grunt, verify that the string 'KBLT' is in the DSDT.
Change-Id: Idf0f23581bcba0b035c126c68fb167274d7c698a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25470
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As part of moving AGESA calls from bootblock to romstage, OemCustomize.c
of all boards using stoneyridge must be available at romstage.
BUG=b:74236170
TEST=Build grunt and kahlee, actual test will be performed at a later patch.
Change-Id: Ide9efdbff6a07c670034391c0d62e8b74fa5c02b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25528
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:73078053
TEST=build & boot Grunt
Change-Id: I2d4ba197b19c4948b867a61575e858b2a826a286
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Audio machine driver will enable/disable clock by making it as
a CCF clock in kernel.
BUG=b:74570989
TEST=cherry-picked https://patchwork.kernel.org/patch/10291875/
on 4.14 kernel
aplay -vv <file>
check register to see clock enabled
kill aplay
check register to see clock disabled
Change-Id: Ia553e55ffb358415067000d2d2d2744322d1c4db
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The GPIO programming of configure_stoneyridge_UART() can be done by the early
GPIO table, AOAC enabling was already removed. So configure_stoneyridge_uart()
became redundant. Remove procedure configure_stoneyridge_uart().
BUG=b:74258015
TEST=Build and boot kahlee, observing serial output does not changes from
previous serial output.
Change-Id: Ie67051d7b90fa294090f6bfc518c6c074d98cc98
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25192
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO 40 isn't currently being used, so set it to be an input.
BUG=b:73387647
TEST=Build & boot grunt
Change-Id: I5a04cbab1276cd20e7f9c7576e8111089dd2b155
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Bayhub part is not used on proto with board_id 0, so disable it.
BUG=b:74248569
TEST=Build & boot Grunt. Bayhub part is disabled.
Change-Id: I635356d41bab637726594d403d66dde730f12256
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This #define tells superio.asl to add a "PNP0501" "Plug and Play
16550A-compatible COM port" entry to kahlee's ACPI tables.
The EC on kahlee boards do not provide a "Serial Port 1" that should
be exposed via ACPI to the OS. In fact, this entry confuses the
kernel and in some cases can cause it to try to redirect output to a
non existing port.
BUG=b:74200887
TEST=Deploy to grunt. Boot kernel with SERIAL_PORT_DFNS undefined and
"earlycon=uart,mmio32,0xfedc6000,115200,48000000" on the kernel
command line, and with an image with serial console enabled.
=> System boots with (kernel) serial console enabled, starting from
0.00 (earlycon), with no gaps in its output, and serial console
also allows logging in.
Change-Id: I0eaed9b4461bb6a6c1aa4ce97752f588d4322b35
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/25021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We want to report the board SKU via the SMBIOS tables. Add support for
this, obtaining the ID itself from the EC.
BUG=b:74175244
BRANCH=none
TEST=manually on grunt with another CL:
mosys platform sku
0
Change-Id: I9e08d64df3f89d3703de047dd9ec8e1717e6b212
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/25011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This commit uses newly defined macros to make it easier to read which
iomux function pads are being configured to use.
TEST=Booted grunt, confirmed display backlight came on.
BUG=b:72875858
Change-Id: I24e5091fc7ef696f8e9c932ce04664e6cc3ccb90
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
There's no need to set the output enable here; this is already handled
by the native function. I'm making this correction in this change to
prevent the GPIO pin descriptions from getting confusing.
BUG=b:72875858
TEST=Booted, confirmed S5_MUX_CTRL high with and without this change.
Change-Id: I9e047be7169586c59892ef2bdab915683feeebda
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For variants that have a cr50 tpm, this enables faster polling when
interacting with the tpm.
BUG=b:72838769
BRANCH=none
TEST=verified on grunt that irq is used and not timeouts for tpm
Change-Id: I5786d334b6c1cc70f4c7107c75b07a7e27ac4428
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This makes the flow for GPIO initialization more closely follow that
what is performed for other boards so that it's easier to read the flow
(and stops relying on BS_WRITE_TABLES).
BUG=b:72875858
TEST=Built and booted grunt, built gardenia.
Change-Id: Ic97db96581a69798b193a6bdeb93644f6a74fc9d
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23679
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This format (one hex digit, followed by 'b', followed by binary digits)
is arguably useful, but also confusing. Use the more common format
instead.
Change-Id: Ide7b0a999483a2dd863a70f8aa42cd0865e2babf
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add an entry to the grunt devicetree defining the ADAU7002 PDM-to-I2S
converter.
BUG=b:72121803
TEST=With grunt audio kernel patches, "aplay -l" shows playback devices:
**** List of PLAYBACK Hardware Devices ****
card 0: acpd7219m98357 [acpd7219m98357], device 0: Playback da7219-hifi-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: acpd7219m98357 [acpd7219m98357], device 2: HiFi Playback HiFi-2 []
Subdevices: 1/1
Subdevice #0: subdevice #0
Change-Id: I90b59ec64f4b841932db42b8a8970ed924283613
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Remove manually written asl entries for grunt's DA7219 and MAX98357A
audio codecs, and replace them with equivalent devicetree entries.
BUG=b:72121803
TEST=With grunt audio kernel patches, "aplay -l" shows playback devices:
**** List of PLAYBACK Hardware Devices ****
card 0: acpd7219m98357 [acpd7219m98357], device 0: Playback da7219-hifi-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: acpd7219m98357 [acpd7219m98357], device 2: HiFi Playback HiFi-2 []
Subdevices: 1/1
Subdevice #0: subdevice #0
Change-Id: Ia658c54a28a5363aabb4c50478adaca1f46d166a
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
* micbias_lvl -> micbias-lvl
* mic_amp_in_sel -> mic-amp-in-sel
BUG=b:71875600
TEST=Checked in kernel the values are set
Change-Id: Ife7e8cdd835cc256cd8265593a94df84a510cebb
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/23603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
I2C bus rise/fall times were measured as follows. Signals were generated
with:
- bus 0: manual i2c driver in depthcharge
- bus 2,3: i2cdetect -r <bus_number>
and then measured manually with an oscilloscope.
BUG=b:72442912
Change-Id: I291e144249271ec34a93417398e54e68b8e21e23
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The wifi card was not being powered, and was being held in reset during
PCI enumeration, so it was not being brought up.
BUG=b:72738963
TEST=Verify wlan card shows up in lspci
Change-Id: I5a1e83298af35aa80c67c75cd6ec0a2c3213891e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23552
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit adds an entry for H1/Cr50 into the devicetree for setting up
ACPI entries for H1 communication.
BUG=b:69250772
TEST=See probe messages in dmesg
Change-Id: Id55ce3364ea4acdb62782758e5bcb2a167286cb9
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23514
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This commit removes a manually written asl file in favor of configuring
the trackpad through devicetree.
BUG=b:72121803
TEST=cat /proc/interrupts with trackpad connected
Change-Id: I38afcf89ea64ffaf6a10bb317c41154feda57e50
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23508
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The gpios for 147 and 148 are connected to PCH_I2C_HUB_SCL and
PCH_I2C_H1_TPM_SDA, respectively. Fix the comment.
BUG=b:64140392
Change-Id: Ibebf6ce7d9fb26276b12b9c9844c260413f0337e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Since the h1 i2c bus is required for verstage mark the bus
as needing to be initialized early. That way, the bus is initialized
in bootblock prior to verstage.
BUG=b:70232394,b:69250772
Change-Id: Ice8525e08ccb438bc468d4c8bd311f72eddc7eb6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
I measured the rise and fall times for I2C bus 1 from userspace
manually, using "i2cdetect 1" called from userspace and an oscilloscope.
This commit fixes the values there to reflect reality.
BUG=b:72442912,b:70232394
Change-Id: I4f593cb2674006060cad9a77753c23f7d9828c9b
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23459
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit adds support for an Elan touchscreen device connected over
I2C via devicetree.
BUG=b:72121803
TEST=Confirm the device is probed for.
Change-Id: Ia9e427dbeab9088f77e3cd751b561f7b9a8cb400
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
I2C bus configuration is generally set up in devicetree.cb. This change
establishes listings for the buses so that they can be used (though
followup changes should update the buses to have correct timings).
BUG=b:72121803
Change-Id: I2b12c82d2bab42ab470aa207880be8876e7cb75f
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[]
with data from agesa_board_gpios[], wrap format and delete
agesa_board_gpios[] and get_gpio_table(). Then remove the
get_gpio_table() call from BiosCallOuts.c. Finally, remove
get_gpio_table() from
google/kahlee/variants/baseboard/include/baseboard/variants.h.
BUG=b:64140392
TEST=Build grunt. Build and boot kahlee, recording serial output. Search
for "stage bootblock" and "stage ramstage", indicating GPIO being
programmed.
Change-Id: I88bf2c855105a6bc458aedfc6da7725662695667
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Create a GPIO programming function that can be called from multiple
stages (bootblock, romstage and ramstage) that will program only the
GPIO specific to the particular stage.
Add dummy table to kahlee, grunt and gardenia to be able to test a build.
BUG=b:64140392
TEST=Build kahlee, grunt and gardenia with GPIO programming call at
bootblock. This call is removed before commit, so bootblock.c is not
committed.
Change-Id: I88d65c78a186bed9739bc208d5711a31aa3c3bb6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|