Age | Commit message (Collapse) | Author |
|
v3.6+ of reference schematics have moved to using active low polarity
for touchscreen GPIO. This change sets the default polarity in
override tree accordingly to active low. To support boards from older
builds, variant_touchscreen_update() already updates the polarity to
active high.
BUG=b:161937506
Change-Id: I370bdb27ea5d0601612d13b515113a6048018964
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This reverts commit 81066b7ce7192432389578fc0f15b3a46da84bad.
Reason for revert: The hang observed when not exposing the reset GPIOs was root caused to zork sharing the same I2C bus between touchscreen and touchpad and interleaving of messages during probe which resulted in incorrect information returned back by touchscreen firmware. Exposing the reset GPIO changed the timing of probe and hence helped workaround the hang issue. The touchscreen driver is now fixed to perform I2C transactions in a single transfer and so the hang is no longer observed when reset GPIO isn't exposed.
BUG=b:162596241
BRANCH=zork
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ica11c33d542dd2324bb0b8905c5de06047cee301
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The USB OC pin mapping is similar enough to move it to the base board
and just have two overrides for trembyle, which is based on an older
version of the schematics, and one override for woomax, which doesn't
use one USB port.
BUG=b:163081097
Change-Id: I7e305d7e6f51d7ef7a4c699e3bacc6bcd699d2f2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This reverts the code from commit 728c0787f2 that removes the reset
GPIO from the touchscreen ACPI interface.
That patch exposes a bug which leads to an invalid opcode trap in the
touchscreen code. Reverting this gets the system working again, but is
not a long-term solution.
BUG=b:162596241
TEST=System boots to login screen.
Change-Id: I57a070d94f961cec43834c8bedd5dafc8a54171a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43078
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support for touchscreen power control using:
* GPIO_90 for trembyle based boards
* GPIO_32 for dalboz based boards
By default, baseboard tables configure these GPIOs as PAD_GPO driven
low and override trees expose these pads as enable_gpio to be used by
ACPI power resource.
In order to support pre-v3.6 boards, override tables configure these
pads as PAD_NC and drop the enable_gpio setting from device tree based
on board version.
BUG=b:161935640, b:162747210
Change-Id: Iba5e36b65b44ea11613b4d5fc8f13ce6433f83ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44193
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
a. USI_REPORT_EN is no longer set to high in coreboot. Instead
GPIO_144 is exposed as stop_gpio in ACPI to allow OS to control this
pad as required.
b. Add Delay after stop_gpio Low - 300ms
BUG=b:162263398
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I3d4dcb6e5cae5d9515abfd415315ec4114ca80b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44107
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:162010077
Change-Id: Iba3e3ec62cdfd818077017abd28fa754c2ae7797
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Raydium ACPI entry currently provides a reset GPIO and an _ON/_OFF
method to the kernel. These are contradictory. The ownership of the GPIO
should be mutually exclusive between either the OS or the FW. Since we
have two methods exposed this causes the OS to reset the TS twice. Once
using the _ON method, and once using the GPIO. Additionally the _ON
method is waiting for 20ms after reset while the OS driver uses a 50ms
delay. The Raydium TS datasheet specifies 20ms for FW ready time, so the
OS driver is adding additional padding.
The reference design has a 32ms rise time on the reset line. So without
this patch, the OS tries to reset the TS using the _ON method and it
waits for 20ms. This is not enough time for the reset line to reach
high, let alone account for the FW ready time. The OS driver then tries
to reset the device by toggling the GPIO. It waits 50ms which is still
2ms less than required.
This CL removes the GPIO from being exported in the _CRS so the OS
driver won't try and reset the device. It also increases the reset delay
by 32ms to account for the rise time.
This isn't a complete fix. I think that the slow rise time is causing
some kind of metastability in the TS reset hardware. Using a script to
bind and unbind the TS driver, the TS device becomes unresponsive after
~200 iterations. The only way to reset the device is to power cycle.
The TS power is also not currently controlled by the power resource.
This means that we have no guarantee over when the reset line is
toggled. This will lead to issues while spending and resuming.
BUG=b:160854397
TEST=Boot trembyle and make sure TS works. Suspend/Resume trembyle 300+
times.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I23131be5d7109eed660a8bd6e2c156c015aa3c4e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPIO_9 is associated with gevent 22. Correct all the misconfigurations
and use macros for clarity as to what bit offset is being used instead
of open coding things.
BUG=b:161205804
Change-Id: Ic4cfd62763d72d12a55f89585f24e07df6af0f4f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43516
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This information is redundant since it's already specified in
baseboard/devicetree_trembyle.cb or baseboard/devicetree_dalboz.cb
domain 0 is still required because sconfig uses it as an identity anchor
to match devicetree and overridetree.
BUG=b:157580724
TEST=Boot zork, usb functional
Change-Id: I3c3c1c2410166b99599d7343fae3ee756f4da321
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43437
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add UPD xhci0_force_gen1 for Trembyle and Ezkinil.
The default setting is set to disable, and set enabled for Ezkinil.
Trambyle -> set default as disable.
Ezkinil -> set enable by request.
BUG=b:156314787
BRANCH=trembyle-bringup
TEST=Build. Verified the setting will be applied on Ezkinil/Trembyle.
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I65d06bfe379f9e42101bfae1a02a619ee2f24052
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2216090
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is a copy of the mb/google/zork directory from the chromiumos
coreboot-zork branch. This was from commit 29308ac8606.
See https://chromium.googlesource.com/chromiumos/third_party/coreboot/+/29308ac8606/src/mainboard/google/zork
Changes:
* Minor changes to make the board build.
* Add bootblock.c.
* Modify romstage.c
* Removed the FSP_X configs from zork/Kconfig since they should be
set in picasso/Kconfig. picasso/Kconfig doesn't currently define the
binaries since they haven't been published. To get a working build
a custom config that sets FSP_X_FILE is required.
BUG=b:157140753
TEST=Build trembyle and boot to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3933fa54e3f603985a0818852a1c77d8e248484f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41581
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|