Age | Commit message (Collapse) | Author |
|
Instead of using 2, 0 is now used for non-CBI provisioned board or
corrupted CBI board to confrom to the sku encoding.
BUG=b:123676982
BRANCH=kukui
TEST=test with un-provisioned board to verify the sku_id.
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: I66f29f8a46cd774b40354def7d3623ec44cb96ce
Reviewed-on: https://review.coreboot.org/c/31623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Initialize GPIO_PCH_WP early in boot. Update cros_gpios[] array with
GPIO_PCH_WP information. Also, Configure recovery mode GPIO as virtual
since hatch does not have one.
BUG=b:125943273
Change-Id: I0b7e6dbf9229941aca4952965fb54f07457dccae
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Hatch implements active high SD_PWR_EN and requires a workaround
in _PS0 and _PS3 control methods to make sure SD_PWR_EN stays low
in D3. Select MB_HAS_ACTIVE_HIGH_SD_PWR_ENABLE to enable the same.
BUG=b:123350329
Change-Id: I96ab9660eb50100207fe9a237f5924b65eae0928
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
SD_CD# in Cannonlake PCH is also wired to an internal virtual GPIO,
expose that GPIO for kernel to configure card detect IRQ.
BUG=b:123350329
Change-Id: I566cc2eb11dc257366897a1efba905b8ddcf493d
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adapted from Chromium commit 5351dc0d
[Edgar: To set the RX ODT limit and dram geometry with RAMID detection]
Several cyan variants require memory init parameters be passed to FSP
for handling of specific Micron modules; without these, RAM init will
fail when loading training data from the MRC cache, and boot will halt.
This was missed when I upstreamed edgar along with the other cyan
variants, so add the required memory init parameters for edgar as per
its source Chromium branch.
Test: build/boot on edgar board with affected Micron memory
modules, verify boot successful with populated MRC cache.
Change-Id: I6a2bc30b54ff1a17c854a90dfcb2308d27ee2be7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31615
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On flapjack, retrieve the board information via CBI interface.
Also reserving 0x2 sku_id for the case of un-provisioned board as this is the id
used prior to the readiness of cbi.
BUG=b:123676982
BRANCH=kukui
TEST=provisioned cbi info and verify the sku_id.
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: Iad7a52df38e2045abbdded8ba0a1f1544de961fc
Reviewed-on: https://review.coreboot.org/c/31586
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For some reason, wake does not currently work from GPP_D21, but IRQs
are working fine from that gpio. Thus, we have to switch IRQ to
GPP_D21 and wake to GPP_A21, which was previously used for IRQs from
the trackpad. Additionally, we need to use two gpios for irqs and
wake source at the moment because of b:123967687, where FSP is locking
down PCR and configuring ITSS. We need to configure the wake source
gpio as inverted and the IRQ gpio as non-inverted until the bug is
resolved.
BUG=b:121212459
BRANCH=None
TEST=run evtest with trackpad
Use trackpad with ChromeOS UI and make sure it reacts as expected.
Run powerd_dbus_suspend and press trackpad and make sure DUT
wakes.
Change-Id: I7b236136befc05c6586d9ba69185ed4b5d385273
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The latest rev. of the atlas board moves the WiFi wake source from
WAKE# to GPP_B7. The original GPP_A0 in the device tree is just
wrong. This also reconfigures DW1 to the GPP_B group so we can use
GPP_B7 as a wake source.
GPP_B7 is still configured as a no-connect in gpio.c, so this doesn't
actually enable WiFi wake. We'll follow up with another patch to set
up GPP_B7 properly on boards that support it.
BUG=b:122327852
BRANCH=none
TEST=atlas still boots
Change-Id: I1816500dd0ab6186fd51aa6945faf73d00c152fe
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When <symbols.h> was first introduced, it only declared a handful of
regions and we didn't expect that too many architectures and platforms
would need to add their own later. However, our amount of platforms has
greatly expanded since, and with them the need for more special memory
regions. The amount of code duplication is starting to get unsightly,
and platforms keep defining their own <soc/symbols.h> files that need
this as well.
This patch adds another macro to cut down the definition boilerplate.
Unfortunately, macros cannot define other macros when they're called, so
referring to region sizes as _name_size doesn't work anymore. This patch
replaces the scheme with REGION_SIZE(name).
Not touching the regions in the x86-specific <arch/symbols.h> yet since
they don't follow the standard _region/_eregion naming scheme. They can
be converted later if desired.
Change-Id: I44727d77d1de75882c72a94f29bd7e2c27741dd8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
EC software sync had been disabled because BIOS was not bundling a
useful EC image. This is no longer required. This CL removes that
change so EC software sync is enabled by default.
BUG=b:124208414
BRANCH=None
TEST=Tested with a system that have a different RW image and verified
that this image was overwritten to the one bundled in the BIOS and
that the EC was running its RW image.
Signed-off-by: Scott Collyer <scollyer@chromium.org>
Change-Id: Ic1ffdb62e9fa2cacb3296cb3807082f23e171ab5
Reviewed-on: https://review.coreboot.org/c/31537
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I91b54b43c8bb5cb17ff86a6d9afa95f265ee49df
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch adds the _DSM method 5 and 6 for entering and exiting S0ix.
The _DSM method gets injected into DSDT table and called from kernel.
LPIT table is hardcoded in this patch but the proper way to implement
is to use inject_dsdt to make the _DSM methods available for soc's to
implement.
Calling the LPIT table from mainboard here so that with the current
implementation the platforms which do not have lpit support throw
compilation error.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ia908969decf7cf12f505becb4f4a4a9caa7ed6db
Reviewed-on: https://review.coreboot.org/c/31101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
After adjustment on Sarien EVT
Touch Screen CLK (Elan): 389.7 KHz
Touch Screen CLK (Melfas): 377.7 KHz
Touch Pad CLK: 385 KHz
BUG=b:122657195
BRANCH=master
TEST=emerge-sarien coreboot chromeos-bootimage
measure by scope with sarien.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: I53b60354e5a7a0ace8efb677775c0a9f8779061d
Reviewed-on: https://review.coreboot.org/c/31476
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow b:123461432#5 to update GPIO H3(CNVI_EN#) for DVT1.
Update setting GPIO H3 to output and low level.
BUG=b:123461432
TEST=Built and tested on sarien system
Change-Id: I6a56df9a7bf75f49133a646312ae5093c2652698
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Follow thermal table (b:123383634 comment#1) for EVT1 tunning.
BUG=b:123383634
TEST=Built and tested on sarien system
Change-Id: I22908e4bf39aedb8cf31a9060084f6f36bff56ca
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Use the common VMX implementation, and set IA32_FEATURE_CONTROL
lock bit per Kconfig *after* SGX is configured (as SGX also sets
bits on the IA32_FEATURE_CONTROL register).
As it is now correctly based on a Kconfig, the `VmxEnable` devicetree
setting vanishes.
Test: build/boot google/[chell,fizz], observe Virtualization enabled
under Windows 10 when VMX enabled and lock bit set.
Change-Id: Iea598cf74ba542a650433719f29cb5c9df700c0f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29682
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Intel SOC can only shadow the top 16MB of SPI into memory so
in order to make it easier to access the NVRAM region with memory
mapped interface move it above the much larger RW_LEGACY region.
I tested to confirm that this region can now be read via MMIO
interface and does not need to use the hwseq SPI controller.
Change-Id: Iafacb01eec07beaf474b6a1f2b36a77117e327da
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Create VR settings configuration as per board design.
BUG=N/A
TEST=Build and boot up into sarien platform.
Change-Id: Ic196fd80e5211bd5146158d4d340b52c850a4e62
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/31404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This change enables mode change as a wake source for S3.
BUG=b:124132058
Change-Id: I95b1eac800858ab17cdf69bdd3f2c5828516c184
Signed-off-by: Mengqi Guo <mqg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:121354442
TEST=None
Change-Id: I348c7106772eecd513baf9abe60ef19008d0ba4d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/31424
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update dptf for arcada EVT.
BUG=b:123924662
TEST=Built and tested on arcada system
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ieed8021b83776fdb6320ff89b57c8d2747667fd5
Reviewed-on: https://review.coreboot.org/c/31331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
We need disable touch screen device on laser SKU ID 6.
BUG=none
TEST=according to sku_id (Laser(convertible): 5, Laser14(clamshell):
6, Laser14(clamshell + touch):7) distinguish whether disable touch
screen device.
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I6953c35a5e8c93d88fe63362156faa351e8ee71f
Reviewed-on: https://review.coreboot.org/c/31428
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DPTF functionality on hatch platform.
Change-Id: If9ef74364616f95b27b73c39fea42d2623d78ae2
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
CNVi Bluetooth module is at port 8 (zero-indexed) and not at port 9. Fix
the device configuration in the devicetree.
BUG=b:123296264
BRANCH=octopus
TEST=Boots to ChromeOS. Checked the SSDT table to ensure that the reset
gpio is exported under the device \_SB_.PCI0.XHCI.RHUB.HS09. Ensured
that the kernel btusb driver is able to find the exported GPIO in the
devices with CNVi BT module.
Change-Id: I302bc87b18a1aaad77bfb73d607ba28b89b79c14
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
According to request of comment 35, setting ELAN as the default.
BUG=b:122019253
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: Iee5e7a21545ca798c0c22f86906acc8e7d81e945
Reviewed-on: https://review.coreboot.org/c/31430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Eanble Elan touch for sarien EVT build
BUG=b:119763054
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: I790436338705fc9d68f714245e9b9bb518ddb30a
Reviewed-on: https://review.coreboot.org/c/31413
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change bumps up the BIOS region to 28MiB to use the hole
between SI_ALL and SI_BIOS. Since this SPI flash part is 32MiB, only
the top 16MiB actually gets memory mapped. Thus, the change ensures
that only RW_LEGACY lies in the 12MiB that is not memory mapped.
BUG=b:123443737
TEST=Verified that hatch still boots up. Ensured that fmap dump looks
correct.
Change-Id: I5832d2b89c7eedfc270755e2add16131cfbddff4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This change enables mode change as a wake source for S3 and S0ix.
Change-Id: I2e7f9997776b1e024ea417eb69e6c2ffa8c62580
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Sarien board may have different touchscreen devices that use the
same I2C slave address but have different requirements such as needing
a special driver or ACPI configuration.
In order to support this the devicetree may be configured with multiple
devices at the same address and at boot time the unused devices will be
disabled.
Because there is no GPIO for selecting the device that is present it can
instead be selected with Kconfig, or by setting a VPD key to the HID of
the touchscreen device that is present. The default for Sarien devices
is to not enable a touchscreen for the OS.
The touchscreen selection is currently limited to the Sarien variant but
this also adds the touchscreen HID for Arcada to Kconfig so it would not
complain about the key not being set.
BUG=b:122019253
TEST=This was tested on a Sarien board by adding a second entry to the
devicetree at the same address. Without this change the SSDT is not
loaded by the kernel because of the address conflict. After this change
no touchscreen is enabled by default, but one can be selected with
Kconfig or by setting the 'touchscreen_hid' VPD key.
Change-Id: I4da12b1de0c551bcd89325fe0d8c66c6ffeb7afc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Follow Northbay and intermal project to add GPIO H3(CNVI_EN#) for DVT1.
BUG=b:123461432
TEST=Built and tested on sarien system
Change-Id: I580a6e094d84a7bada534b14c2b65ecf4b9942b0
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Follow b:123342945 to add GPIO H15(BT_RADIO_DIS#) for DVT1.
BUG=b:123342945
TEST=Built and tested on sarien system
Change-Id: I0caf97f6a2a8abf2914667350c76300733ead1b8
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Under some scenarios the key ladder on the Cr50 can get disabled. If
this state is detected, trigger a reboot of the Cr50 to restore full
TPM functionality.
BUG=b:121463033
BRANCH=none
TEST=Built coreboot on sarien and grunt platforms.
TEST=Ran 'gsctool -a -m disable' and reboot. Verified coreboot sends
VENDOR_CC_IMMEDIATE_RESET command to Cr50 and that the Cr50 resets and
then the platform boots normally.
TEST=Performed Cr50 rollback to 0.0.22 which does not support the
VENDOR_CC_TPM_MODE command, confirmed that platform boots normally and
the coreboot log captures the unsupported command.
Tested-by: Keith Short <keithshort@chromium.org>
Change-Id: I70e012efaf1079d43890e909bc6b5015bef6835a
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This implementation configures GPIO (GPP_A21, GPP_C21, GPP_D16)
pad in non-inversion mode i.e Rx PAD state is not inverted as
it is sent from GPIO to IOAPIC.
BUG=b:123315212
TEST=Tested for below:
-> Verify touchpad is working fine.
-> TPM init is successful and boot with fixed boot media.
Change-Id: I6034fd07ccc96a19218d57ef8bb9049c4b963ea5
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/31328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All platforms using this code have NO_CAR_GLOBAL_MIGRATION.
Change-Id: I72effa93e36156ad35b3e45db449d8d0d0cabf06
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
It needs to tune usb2eye setting for these ports:
USB2[4] - type-c port
USB2[6] - camera
BUG=b:122878632
BRANCH=octopus
TEST=built and passed usb2eye SI test
Change-Id: Iaa3adaab2f391e95730b141dc0237ca62c459e5a
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31359
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We leave it to linker garbage collection to drop
unreferenced code and symbols from final object files.
Function declarations and definitions are to be guarded
with preprocessor directives only as a last resort.
Change-Id: Ie8748ccddc8e31569c58deba5d08c98a04326fa8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Use AGPIO 10 as the EC sync interrupt for MKBP events for sensor data.
On this platform, interrupts are routed via the GPIO controller so need to be
registered using GpioInt instead of Interrupt.
BUG=b:123750725
BRANCH=grunt
TEST=MKBP events still received (with matching EC and kernel changes)
Change-Id: If499d24511bbaa7054207b7e0b98445723332c4f
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Traditionally, we have always allocated 1 DRAM ID per part number.
However, on nami, we have run out of DRAM IDs because we have
supported so many different parts. We are now adopting the use of
generic SPD files that are feature-based rather than specific to each
part, allowing us to support multiple parts with a single SPD.
The common SPDs were created by taking current SPDs in Nami (which is
using the same DDR4 parts as Hatch) and zeroing out all the
manufacturer information and part names. Additionally, we zeroed out
bytes 128 (raw card extension, module nominal height), 129 (module
maximum thickness), and 130 (reference raw card used) after verifying
that they are not used in FSP. We verified with these fields zeroed
out, all nami devices could boot up without errors. We also verified
on the two Hatch skus that we have (4G 2400, 8G 2666) that the generic
SPDs boot properly.
BUG=b:122959294
BRANCH=None
TEST=Make sure that we can boot up on both 4G Samsung and 8G Hynix DDR4
devices that we currently have.
Change-Id: I14d9e6b13975b6a65b506e6cd475160711b8f6d4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
"is_wakeup_source" flag is used to indicate if the concerned device can
trigger a wakeup. This flag is redundant with the "wake" GPE event
definition. So remove the redundant flag and use the "wake" GPE event to
mark the wakeup source.
BUG=None
BRANCH=None
TEST=Boot to ChromeOS. Ensure that the device is marked as wakeup-source
in SSDT if wake GPE is configured. Ensure that the system can suspend
and the device acts as a wakeup source
Change-Id: I99237323639df1cb72e3a81bcfed869900a2eefa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
See Documentation/coding_style.md, specifically "Placing Braces and
Spaces" section.
Change-Id: Ia6a2f3d3547c16500996260b0ece9ec693f00113
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ibb7ce42588510dc5ffb04c950c4c8c64e9a2fa37
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This change uses cnl_configure_pads to configure GPIOs in ramstage so
that cannonlake SoC code can re-configure the GPIOs after FSP-S is
run. This is just adding a workaround until FSP-S is fixed.
BUG=b:123721147
BRANCH=None
TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch.
Change-Id: I9973c6c49154f1225f0ac34a3240a0d19f911f18
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch performs below tasks
1. Create SOC_INTEL_COMMON_CANNONLAKE_BASE kconfig.
2. Allow required SoC to select this kconfig to extend CANNONLAKE
SoC support and add incremental changes.
3. Select correct SoC support for hatch, sarien, cflrvps
and whlrvp.
* Hatch is WHL SoC based board
* Sarien is WHL SoC based board
* CFLRVP U/8/11 are CFL SoC based board
* WHLRVP is based on WHL SoC
4. Add correct FSP blobs path for WHL SoC based designs.
Change-Id: I66b63361841f5a16615ddce4225c4f6182eabdb3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change enables I2C bus 2, 3 and 4 in devicetree and configures
GPIO pads for the same. It also configures pads for I2C5 as
no-connect.
BUG=b:123711244
TEST=Verified that i2c shows up in "i2cdetect -l" after booting to OS.
Change-Id: Ib4714a670d73228332115415e4393f82802c6475
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31237
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Current coreboot size is not adequate for adding new features.
Note for cros: This change is for merge to ToT only and should not be
cherry-picked into reef's firmware branch.
BUG=chromium:903833
TEST=emerge-reef coreboot
Change-Id: Ie7a25c4638c474e81fb34b57de0dfc1bf393ea67
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Select the appropriate system type for the different variants of
the Sarien board.
This will allow the Arcada variant to use the tablet mode feature
of the Intel Virtual Button driver.
Change-Id: I8a829aab012256ec196c8ec0fa298fd2bc77f2e1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds keyboard backlight feature for Hatch platform.
BUG=b:122799544
BRANCH=none
TEST=keyboard backlight works when EC reports correct info.
Change-Id: I29273122f061e0e442f6629351ef3670535c0507
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31175
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reconfigures the GPP_D1 GPIO pin as a no-connect. It really
doesn't go anywhere today or on previous revs of the board.
BUG=b:110614620
BRANCH=none
TEST=atlas still boots
Change-Id: Iea53cf909f8f060c4e0f14e8b4ad579b838b7caa
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 7696290004b6490c7ef8027d7ddf67b163e7dad8.
We're seeing trackpad problems on some units with the I2C bus running
at 1MHz but not at 400KHz. So, revert back to 400KHz until we
understand how to make 1MHz operation more robust.
BUG=b:123650686
Change-Id: Ifb06afece9eee0c153240d35e6c3001f5b74f310
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The default value for Chrome OS HWID should be different.
Calculated as HWID v1.
BUG=b:123336677
BRANCH=kukui
TEST=build and boots properly.
Change-Id: I39c640562c1c3b117292b8abacd36a4a9c2fa6c6
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|