summaryrefslogtreecommitdiff
path: root/src/mainboard/google
AgeCommit message (Collapse)Author
2017-02-23google/gru: whitespace fixPatrick Georgi
Follow up to https://review.coreboot.org/#/c/18460/ Change-Id: Ic3aada2acf3051622698e10d2e764050e16480d5 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: https://review.coreboot.org/18475 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23google/gru: Tuning USB 2.0 PHY0 and PHY1 squelch detection thresholdWilliam wu
According to USB 2.0 Spec Table 7-7, the High-speed squelch detection threshold Min 100mV and Max 150mV, and we set USB 2.0 PHY0 and PHY1 squelch detection threshold to 150mV by default, so if the amplitude of differential voltage envelope is < 150 mV, the USB 2.0 PHYs envelope detector will indicate it as squelch. On Kevin board, if we connect usb device with Samsung U2 cable, we can see that the impedance of U2 cable is too big according to the eye-diagram test report, and this cause serious signal attenuation at the end of receiver, the amplitude of differential voltage falls below 150mV. This patch aims to reduce the PHY0 and PHY1 otg-ports squelch detection threshold to 125mV (host-ports still use 150mV by default), this is helpful to increase USB 2.0 PHY compatibility. BRANCH=gru BUG=chrome-os-partner:62320 TEST=Plug Samsung U2 cable + SEC P3 HDD 500GB/Galaxy S3 into Type-C port, check if the USB device can be detected. Change-Id: Ia0a2d354781c2ac757938409490f7c4eecdffe61 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 7d74311c25762668386061234df0562f84b7203e Original-Change-Id: Ib20772f8fc2484d34c69f5938818aaa81ded7ed8 Original-Signed-off-by: William wu <wulf@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/431015 Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com> Original-Tested-by: Inno Park <ih.yoo.park@samsung.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18462 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins)
2017-02-23google/gru: update the pwm regulatorCaesar Wang
As David commented the "Bob and other follow-ons match Gru, Kevin should be the special case here", and update the calculations value for gru/bob board. From the actual tests, some regulator voltage than the actual set of less than 20mv on bob board. (e.g: little-cpus and Center-logic) Update the {min, max} regulator voltage for Bob board. Make sure we get the accurate voltage. BUG=chrome-os-partner:61497 BRANCH=none TEST=boot up Bob, measure the voltage for little cpu and C-logic. Change-Id: Iad881b41d67708776bfb681487cf8cec8518064e Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 25e133815f49018e7496c75077b8559c207350a4 Original-Change-Id: I3098c742c7ec355c88f45bd1d93f878a7976a6b4 Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-Reviewed-on: https://chromium-review.googlesource.com/424523 Original-Reviewed-by: David Schneider <dnschneid@chromium.org> Original-Reviewed-by: Brian Norris <briannorris@chromium.org> Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-Reviewed-on: https://chromium-review.googlesource.com/430403 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18460 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23mb/google/poppy: Enable support for DPTFSumeet Pawnikar
This patch adds the DPTF settings specfic to the mainboard and enables the CPU and other thermal sensors as participant device for poppy. It enables the DPTF flag in the device tree for poppy. It also includes the DPTF specific ASL file in the main DSDT definition. BUG=None BRANCH=None TEST=Built for poppy. Change-Id: If44b01dd3c17fea06681ccf50e8e9f406e642e36 Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/17926 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-23google/oak: Add initial support for RowanYidi Lin
Update GPIO controls and mainboard configurations for Rowan. [pg: use the opportunity to clean-up the gerrit-rebase task list with the entirely unrelated Ignore-CL-Reviewed-on lines] BUG=chrome-os-partner:62672 BRANCH=none TEST=emerge-rowan coreboot Change-Id: I110fb368b3d9fa9dfb2bf091342dfb511ff7c09c Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: f4252cbe94a7456108aaa522e170bca5dcb1fdd1 Original-Change-Id: I18ebc3ccf4c7d051839d7c50e9b0682ef8f09830 Original-Signed-off-by: Yidi Lin <yidi.lin@mediatek.com> Original-Reviewed-on: https://chromium-review.googlesource.com/430557 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/341513 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/327003 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/355221 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/354670 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361360 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361361 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361362 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361363 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/382320 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405110 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405130 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/419795 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/424139 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430293 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430294 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430295 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427820 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427821 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427822 Reviewed-on: https://review.coreboot.org/18463 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23google/gru: improve eye diagram for passing the testCaesar Wang
The children of Gru should share the benefits. In the real world, Bob can't pass the eye diagram tests. BUG=chrome-os-partner:62714 BRANCH=firmware-gru-8785.B TEST=build coreboot Change-Id: I2470bbc81acdaf2458d660dca5dc307cc3038f83 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: d0cb3e718a7571f602a00c08a42019851634e7fd Original-Change-Id: I0ccb48bb52eb770ccc9c8c265b07df46b0308dd3 Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/440745 Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/441468 Reviewed-on: https://review.coreboot.org/18461 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-22acpi: Add ACPI_ prefix to IRQ enum and struct namesFurquan Shaikh
This is done to avoid any conflicts with same IRQ enums defined by other drivers. BUG=None BRANCH=None TEST=Compiles successfully Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18444 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-22google/gru: Fix whitespacePatrick Georgi
Change-Id: I538c28fb1bc412947ef9df947fa3f6a3312aeb4b Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: https://review.coreboot.org/18322 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Enable Realtek 5663 supportRizwan Qureshi
Enable Realtek RT5663 codec i2c device and add required SSDT parameters. BUG=chrome-os-partner:62051 BRANCH=None TEST=With required driver support in kernel verify audio on headset Change-Id: I9b9eb1e7edca56870f5be0e4fd603c9b0dc7f9de Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18216 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Enable Maxim MAX98927 codecRizwan Qureshi
Enable Maxim 98927 codec i2c device and add required SSDT parameters. BUG=chrome-os-partner:62051 BRANCH=None TEST=with required driver support in kernel verify audio on poppy on-board speakers. Change-Id: Id731de42d77204d59f32ac4c33a245837d6e2107 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Dylan Reid <dgreid@chromium.org> Reviewed-on: https://review.coreboot.org/18215 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Generate required nhlt tableRizwan Qureshi
poppy board uses Maxim 98927 speaker codec and Realtek RT5663 for headset. Select the apropriate NHLT blobs to be packaged in CBFS. Also, generate the required ACPI NHLT table for codec and the supported topology in poppy. BUG=chrome-os-partner:62051 BRANCH=None TEST=With the required driver support in kernel verify that the Audio plays on on-board speakers and headset, recording works from on-board mics and headset mics. Change-Id: I98c65038b35fe99a661807de0766e6eac2c80eed Signed-off-by: M Naveen <naveen.m@intel.com> Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Reviewed-on: https://review.coreboot.org/18214 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20drivers/i2c: Use I2C HID driver for wacom devicesFurquan Shaikh
Wacom I2C driver does the same thing as I2C HID driver, other than defining macros for Wacom HID. Instead of maintaining two separate drivers providing the same functionality, update all wacom devices to use generic I2C HID driver. BUG=None BRANCH=None TEST=Verified that ACPI nodes for wacom devices are unchanged. Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18401 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20google/eve: Set touchscreen I2C bus speed to 1MHzDuncan Laurie
Enable Fast-Plus speed for the touchscreen device so it can be used at 1MHz instead of 400KHz. BUG=chrome-os-partner:61277 TEST=manual testing on Eve P1, needs backported kernel patches to actually make use of any I2C speed other than 400KHz Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18397 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-20google/eve: Add audio devicesDuncan Laurie
Add the audio devices to Eve mainboard: - Describe Maxim 98927 speaker amps and RT5663 headphone codec in ACPI so they can be enumerated by the OS. - Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH. BUG=chrome-os-partner:61009 TEST=manual testing on Eve P1 with updated kernel to ensure that both speakers and headset are functional. DMIC support is is still being worked on and is not yet functional. Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18398 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-02-20mainboard/{google,intel}: Change config option selectionFurquan Shaikh
Change config option selection from "config xyz default y" to "select xyz" if the config option has no dependencies. BUG=None BRANCH=None TEST=Verified that config option selection remains unchanged. Change-Id: I259ae40623b7f4d5589e2caa0988419ba4fefda4 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18400 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20mainboard/google/reef: Remove config DRIVERS_GENERIC_GPIO_REGULATORFurquan Shaikh
Since we are not using gpio regulators on reef anymore, remove the selection from Kconfig as well. BUG=None BRANCH=None TEST=Compiles successfully. Change-Id: Iae7d88dec3ac476d65b292f97a6ba3add71ce07a Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18399 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20google/slippy: consolidate variants' common mainboard.asl codeMatt DeVillier
Move code common code from each variant's mainboard.asl into common ACPI code for all variants (like google/auron). This also adds the _PRW method for the LID0 device for falco and peppy, which omitted the function when they were originally upstreamed. See Chromium commit c8b41f7, falco: Add _PRW for LID0 ACPI Device Change-Id: I7f5129340249a986f5996af37c01ccbde8d374e8 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18368 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-20google/eve: Set rise/fall timing values for I2C bus 1Duncan Laurie
Apply the measured rise and fall times for I2C bus 1 on Eve so it can be tuned properly for 400KHz operation. BUG=chrome-os-partner:63020 TEST=verify I2C1 bus speed with a scope Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18396 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-20google/eve: Fix FPC supportDuncan Laurie
Currently UART0 GPIOs are being put into native mode during FSP-S stage, so have ramstage re-configure them back to regular GPIO mode. GPP_C8 does not seem to be functioning properly when routed to the APIC, possibly due to the UART0 being enabled even though it is unused, which is required because UART0 is PCI 1e.0 and so must be present for other 1e.x functions to be enumerated. Instead, use this pin as a GPIO interrupt so it will be routed through the GPIO controller at IRQ 14. GPP_C9 was inverted and was only working because the pin was being re-configured in FSP-S. Also export the reset gpio as a device property so it can be used by the kernel driver, which will stop it from complaining at boot. BUG=chrome-os-partner:61233 TEST=verify that the interrupt and device is functional in the OS Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18395 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/eve: select SOC_INTEL_KABYLAKERizwan Qureshi
eve is based on Kabylake SoC hence select the appropriate config. Change-Id: I756dda5a1924e83a02ac1cebb1907884f436a13f Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18314 Tested-by: build bot (Jenkins) Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/poppy: select SOC_INTEL_KABYLAKERizwan Qureshi
poppy is based on Kabylake SoC hence select the appropriate config. Change-Id: Ie339a3991eeccb8a7dba983a2b5ab5d1c996ce9d Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18313 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/google/poppy: Generate digitizer node in SSDTFurquan Shaikh
Add support for generating digitizer node in SSDT using wacom i2c driver. BUG=None BRANCH=None TEST=Verified that the node shows up in SSDT. Change-Id: If7e1e2463778c2ff7263eff995def149457edcde Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18373 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-16mainboard/google/eve: Generate FPC device using SPI SSDT generatorFurquan Shaikh
Use the newly added SPI SSDT generator for adding FPC device. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully. Verified that the SSDT entry matches the entry in mainboard.asl Change-Id: I1b3c33f2b4337735a9725dd4eb6193b2455962d7 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18343 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-15mainboard/google/reef: add sand variantYH Lin
Create the initial Sand variant which refers to the Reef. Sand is APL board that derives from reference board Reef. BRANCH=master BUG=chrome-os-partner:62200 TEST=Build (as initial setup) Signed-off-by: YH Lin <yueherngl@chromium.org> Change-Id: Iba8c5653b6176676c759d2b48063f0c0c6cde625 Reviewed-on: https://review.coreboot.org/18324 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-14google/eve: change touchpad HIDWei-Ning Huang
Change touchpad HID to use with the Google Centroiding Touchpad driver. BUG=chrome-os-partner:61088 TEST=`emerge-eve coreboot` Change-Id: I199ff46f1a93d3eccc8c694742585dcf37b2373f Signed-off-by: Wei-Ning Huang <wnhuang@google.com> Reviewed-on: https://review.coreboot.org/18359 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-14google/rambi: add explicit pull-down for ram-idMatt DeVillier
Some variants need the internal pull resistor on GPIO_SSUS_40 set explicitly to pull down rather than disabling the pull, in order for the ram-id to be read correctly via GPIO. Correct this by adding a function to enable and set the internal pull and define its use as needed in the board's variant.h. Chromium source: branch: firmware-gnawty-5216.239.B /src/soc/intel/baytrail/baytrail/gpio.h#418 /src/mainboard/google/gnawty/romstage.c#60 Test: boot 4GB Candy board and observe correct RAM id, amount detected Change-Id: I8823c27385f4422184b5afa57f6048f7ff2a25ab Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18309 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-14google/poppy: select NO_FADT_8042Jenny TC
Poppy doesn't support 8042 keyboard. Select NO_FADT_8042 to disable 8042 in FADT header. Kernel will not try to access 8042 region if 8042.FADT=0 BUG=chrome-os-partner:61858 TEST=Boot OS and verify FADT 8042 flag Change-Id: I00182eb4b059d4d9f0705d349dc98651e3955f0d Signed-off-by: Jenny TC <jenny.tc@intel.com> Reviewed-on: https://review.coreboot.org/18311 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-13mainboard/google/snappy: Update DPTF settingsWisley Chen
Update DPTF parameters based on thermal team test result. 1. Update TSR2 trigger points. TSR2 passive point: 70, critical point: 90 2. Set PL2 Max to 15W. BUG=chrome-os-partner:61383 BRANCH=reef TEST=build, boot on snappy, and verified by thermal team Change-Id: I8d01d6c1d7eabd359ceb131f3cd10965d4ac2c42 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18318 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-11mainboard/google/reef: Increase PL1 sampling periodSumeet Pawnikar
Performance degradation seen with current PL1 throttling rate as 8 seconds for TSR1 sensor with Aquarium workload. After fine tuning PL1 throttling rate to 15 seconds, fps score improved. BUG=chrome-os-partner:60038 BRANCH=reef TEST=Built and tested on electro system Change-Id: I5cdebb08e00f0f28b88f1c6b2b1cafaeb8cdb453 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/18317 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
2017-02-11google/gru: add scarlet variantphilipchen
There will be more follow-up changes. BUG=chrome-os-partner:62377 BRANCH=None TEST=emerge-scarlet coreboot libpayload Change-Id: I9ca45598ff0ab12bf8063d16a86be564cf509390 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: a020a9ba1228b15599e202972df0096f58b1b31c Original-Change-Id: I4804239483f8b35bc3703aa62c2a8fd642e0234a Original-Signed-off-by: philipchen <philipchen@google.com> Original-Reviewed-on: https://chromium-review.googlesource.com/433039 Original-Commit-Ready: Philip Chen <philipchen@chromium.org> Original-Tested-by: Philip Chen <philipchen@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18296 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
2017-02-07mainboards/google/reef: Add support for tablet mode switch.Gwendal Grignou
Reef is a convertible add support for sending Tablet mode switch changes from EC to AP. Change-Id: I6dfddbfdb5a2ffbdfd77c5f49602bf68e9693a06 Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/18277 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-07google/eve: Add support for tablet mode switch.Gwendal Grignou
Eve is a convertible add support for sending Tablet mode switch changes from EC to AP. Change-Id: I35133ebc1439852d0ceb88d7d679b37356b0869d Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/18276 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-05google/eve: Fix keyboard backlight enable in wake from G3Duncan Laurie
The WAK_STS bit is not set in a wake from G3, so the check for this bit needs to only be done when checking for a wake from S3. This change correctly enables the keyboard backlight in wake from G3 and only does not enable it during a wake from S3. BUG=chrome-os-partner:58666 TEST=Use Refresh+Power to issue hard reset and ensure that the keyboard backlight turns on like it does when waking from S5. Also force enter hibernate with Alt+VolumeUp+H and then power back up and ensure that the keyboard backlight is enabled when booting. Change-Id: I44045950e38aa5e5ae96a79385d604791852c7e6 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18280 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-04google/jecht: Fix LED for guado/rikku variantsMatt DeVillier
When guado/rikku/tidus were rolled into jecht, an error was made in set_power_led() as guado/rikku set the polarity differently than tidus. Fix the power LED for guado/rikku by setting the polarity correctly. Test: boot guado/rikku and observe proper function of power LED under S0, S3, and S5 power states. Change-Id: I23072ac60bc9683776f748ca1326d98257c3c54f Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18249 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-04Revert "google/pyro: remove Wacom touchscreen probed flag"Kevin Chiu
Reason for revert: Pyro has two touchscreen sources: WACOM/ELAN. It will not have both touchscreen IC in one system at the same time. So the "probed" property of WACOM i2c device is mandatory to set for kernel to know whether it exists before driver initializes it. Otherwise in ELAN case, when driver fails to init WACOM i2c device, ACPI _OFF will be invoked to set GPIO#152 low to cut off power. BUG=chrome-os-partner:62371 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: I30f467bd8720d959686dc14f7877e6bc11ea6213 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18291 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-04google/eve: Fix DRAM DQS mapDuncan Laurie
This change fixes the two sets of pins that were swapped in the map of DQS signals from CPU to DRAM for channel 1. Although this does not appear to have any impact to the system it does result in different register values for DQS pin mapping that are programmed inside FSP. BUG=chrome-os-partner:58666 TEST=This fix was verified against the current schematic and using FSP debug output. Change-Id: I45b821071ba287493b3b13204b7f5b38e06eee75 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18279 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-04google/poppy: Set GPIO GPP_D22 highRizwan Qureshi
same change as I49935e659bf67225d3f5db1b06acc2cd046dcd74 this is required for poppy board as well. GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals when doing GPIO-driven I2S. This needs to be high by default so the DSP can drive these signals, instead of low where it is enabled for GPIO-driven I2S and the DSP cannot drive these signals. BUG=None BRANCH=None TEST=play test sound in OS over internal speaker Change-Id: I1695e9198f8f78e9c5ad6df6c1ac073ac1762c6b Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18282 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-04google/eve: Set GPIO GPP_D22 highDuncan Laurie
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals when doing GPIO-driven I2S. This needs to be high by default so the DSP can drive these signals, instead of low where it is enabled for GPIO-driven I2S and the DSP cannot drive these signals. BUG=chrome-os-partner:58666 TEST=play test sound in OS over internal speaker Change-Id: I49935e659bf67225d3f5db1b06acc2cd046dcd74 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18281 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-03mainboard/google/snappy: Set PL2 override to 15000mWHarry Pan
This patch sets PL2 override value to 15W in RAPL registers. BUG=chrome-os-partner:62110 BRANCH=reef TEST=Apply new firmware to evaluate Octane benchmark score. Change-Id: I51734051586753677129314b5273fb275c74f5d2 Signed-off-by: Harry Pan <harry.pan@intel.com> Reviewed-on: https://review.coreboot.org/18283 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-02-01Add Baytrail ChromeOS devices using variant schemeMatt DeVillier
Add new ChromeOS devices banjo, candy, clapper, glimmer, gnawty, heli, kip, orco, quawks, squawks, sumo, swanky, and winky using their common reference board (rambi) as a base. Chromium sources used: firmware-banjo-5216.334.B 32ec493 [chromeos: vboot_loader: Set...] firmware-candy-5216.310.B 519ff11 [baytrail: Preserve VbNv around...] firmware-clapper-5216.199.B 80d55e3 [baytrail: add code for...] firmware-glimmer-5216.198.B fae0770 [baytrail: add code for...] firmware-gnawty-5216.239.B 952adb7 [Gnawty/Olay: Add 2nd source...] firmware-heli-5216.392.B f1f3604 [helis: Lock ME / TXE section...] firmware-kip-5216.227.B db3c5d9 [kip: update spd for for MT41K256M16*] firmware-orco-5216.362.B 76f1651 [Orco: Adjust rx delay for norm.] firmware-quawks-5216.204.B edb60c9 [Quawks: Update SPD data] firmware-squawks-5216.152.B c6573dc [Squawks: Update SPD data] firmware-sumo-5216.382.B c62b6f23 [Ninja, Sumo: Add SPD source...] firmware-swanky-5216.238.B 233b2a7 [Swanky: update SPD table] firmware-winky-5216.265.B ce91ffc [Add to support HT Micron...] The same basic cleanup/changes are made here as with the initial BYT variant commit: - remove unused ACPI trackpad/touchscreen devices - correct I2C addresses in SMBIOS entries - clean up comment formatting - remove ACPI device for unused light sensor - switch I2C ACPI devices from edge to level triggered interrupts, for better compatibility/functionality (and to be consistent with other recently-upstreamed ChromeOS devices) - Micron 2GB SPD file for kip with updated values renamed to distinguish from same file used by other boards Change-Id: Ic66f9b539afb5aff32c4c1a8563f6612f5a2927c Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18164 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-01-31google/veyron*: mark GPIO array non-staticPatrick Georgi
That status isn't needed and making it non-static helps gcc 4.9.2 (or any compiler that insists on "standard C" behaviour with global const initializers) Change-Id: Ib1fbd5213d262e653f31564b106095b4a28292f6 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/18266 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-31mainboard/google/reef: remove NHLT DMIC 1ch and 2ch configurationSathyanarayana Nujella
Apollolake boards should use DMIC-4ch configuration in Kernel side and use CaptureChannelMap in userspace to distinguish boards with different number of DMIC's. So, NHLT DMIC 1-ch & 2-ch endpoint configuration will not be required and hence removed. BUG=chrome-os-partner:60827 TEST=Verify internal mic capture TEST='arecord -Dhw:0,3 dmic_4ch.wav -f S16_LE -r 48000 -c 4 -d 10' works Change-Id: Ibe81290906c9e379ae49e437648ee9cd6f123ff8 Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-on: https://review.coreboot.org/18252 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-31mainboard/google/reef: Set edge triggered interrupt for GPIO_22Vaibhav Shankar
EC sets the logic level based on outstanding wake events. When GPIO_22 is configured as a level triggered interrupt, the events are not cleared from the interrupt handler. Hence, we'd just be re-signalling over and over causing an interrupt storm upon lid open. So, GPIO_22 needs to be configured as EDGE_SINGLE instead of LEVEL. BUG=chrome-os-partner:62458 TEST=Lid close/open. check CPU usage using top. It should not show 70% CPU usage. Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Change-Id: I710a690578c6e5b63be34b7fbcb21c703ef56e3a Reviewed-on: https://review.coreboot.org/18267 Tested-by: build bot (Jenkins) Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-29mainboard/google/snappy: Update WDT touchscreen deviceFurquan Shaikh
Export PowerResource for WDT touchscreen device. BUG=chrome-os-partner:62311, chrome-os-partner:60194, chrome-os-partner:62371 BRANCH=reef TEST=Compiles successfully. Change-Id: Icc5be170353753201d3571c39b50e29424d4d6d3 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18240 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-29mainboard/google/pryo: Update touchscreen device ACPI nodesFurquan Shaikh
1. For ELAN, export reset GPIO as well as PowerResource 2. For WCOM, export PowerResource BUG=chrome-os-partner:62311, chrome-os-partner:60194, chrome-os-partner:62371 BRANCH=reef TEST=Verified that touchscreen works on pyro with WCOM device on power-on as well as after suspend/resume. Change-Id: I0306e24e19bf821cd3e08fdacc0d78b494c9a92f Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18239 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-29i2c/generic: Allow GPIOs to be put in _CRS and PowerResource in ACPIFurquan Shaikh
Linux kernel expects that power management with ACPI should always be handled using PowerResource. However, some kernel drivers (e.g. ELAN touchscreen) check to see if reset gpio is passed in by the BIOS to decide whether the device loses power in suspend. Thus, until the kernel has a better way for drivers to query if device lost power in suspend, we need to allow passing in of GPIOs via _CRS as well as exporting PowerResource to control power to the device. Update mainboards to export reset GPIO as well as PowerResource for ELAN touchscreen device. BUG=chrome-os-partner:62311,chrome-os-partner:60194 BRANCH=reef TEST=Verified that touchscreen works on power-on as well as after suspend-resume. Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18238 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-01-29mainboard/google/reef: Set IOSSTATE for trackpad I2C GPIOsVaibhav Shankar
I2C data (GPIO_132) and Clk (GPIO_133) lines are pulled low during standby states S3/S0ix. This causes leakage of power. To reduce the leakage, we have to pull these lines high during S3/S0ix. This is done by programming the IOSSTATE to HIz. Also note that we are using the internal pull ups to keep at SOC at 1.8V and the I2C lines are not floating. BUG=chrome-os-partner:62428,chrome-os-partner:61651 TEST=Enter S3/S0ix. Measure trackpad power. It should be less than 4mW. Also I2c lines should be pulled high in S3/S0ix. Change-Id: I5570ac37ec3cc41f6463dd6b858fdb56a20a1733 Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-on: https://review.coreboot.org/18251 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-01-26google/pyro: Add USB2 phy setting overrideKevin Chiu
In order to pass type A USB2 eye diagram, USB2 port#0/#1 PHY register will need to be overridden. port#0: PERPORTPETXISET = 7 PERPORTTXISET = 1 IUSBTXEMPHASISEN = 3 PERPORTTXPEHALF = 0 port#1: PERPORTPETXISET = 7 PERPORTTXISET = 2 IUSBTXEMPHASISEN = 3 PERPORTTXPEHALF = 0 BUG=chrome-os-partner:59491 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: I8e67a6f0192d1c0abf6ec4926c2a17e44c818948 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18229 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-26google/pyro: Disable Wacom touchscreen probedKevin Chiu
Wacom touchscreen is i2c hid device and it's the device that always exists. So no need to set "probed" property for it. BUG=chrome-os-partner:61513 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: I27fe18ceadd03029b826e0237f80132eda1089b0 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18227 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-25google/pyro: Modify Wacom touchscreen IRQ type to level-triggeredKevin Chiu
Follow i2c-hid spec definition, level trigger interrupt is required for i2c-hid device. BUG=chrome-os-partner:61513 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: Ia825bd0c898e71e2ee2bf411f117a49a8fb411b6 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18217 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-15 16:42:20 +0000