Age | Commit message (Collapse) | Author |
|
Add support for Lenovo Thinkpad L520.
The files are generated by autoport,
and are successfully tested on the board.
L520 has got 4MiB flash chip, that contains a "slim" ME
with 1.2MiB only. The flash IC has to be desoldered, as
it won't be accessible in circuit. It is located on top
of the mainboard right under the touchpad.
Test-setup:
Extract the following blobs from vendor BIOS:
* Intel Flash Descriptor
* Intel Management Engine
* Intel VBios
The laptop has been externaly flashed. It was able to
turn on the display and load SeaBIOS.
Latest debian has been booted from harddisk.
Latest fedora has been booted from USB flash drive.
The following hardware has been tested and is working:
* Display using Option Rom
* PCIe wifi
* Ethernet
* Keyboard, trackpoint and touchpad
* Some Fn functions keys
* Volume Keys (except mic mute)
* Status LEDs
* Audio (headphone jack only)
* USB ports
* Native raminit dual channel (2 DDR3-1333 DIMMs tested)
* SATA cdrom
* SATA harddrive
Broken:
* Some Fn functions keys
* Microphone mute button
* Speakers (but headphone jack gives sound)
Untested:
* Expansion slot
* SD card slot
* Docking station
* Native gfx init
The EHCI debug port is the first one on the right side.
Change-Id: Ic8943799b953bde09ff1daf8427ce5125a0778ca
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18003
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This driver to configure the clock generator is not used.
Change-Id: I156a42dfc336ff45acdcb6d8618bbd12671b66a7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18104
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The Lenovo T400 has a CPU socket that can fit quad cores.
Change-Id: I585775ac9510cc7d2c2d731531f536c1a56b81e8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18059
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This is more consistent with newer Intel targets.
This a static struct so it is initialized to 0 by default.
To make it more readable:
* only setting to GPIO mode is made explicit;
* only pins in GPIO mode are either set to input or output since this
is ignored in native mode;
* only output pins are set high or low, since this is read-only on
input;
* blink is only operational on output pins, non-blink is not set
explicitly;
* invert is only operational on input pins, non-invert is not set
explicitly.
Change-Id: I05f9c52dee78b7120b225982c040e3dcc8ee3e4e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17639
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Correct tabs that were intended as spaces.
Change-Id: Idcf33d829f87a866b5ed880527102918d5b93842
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/17905
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
Make the ending comment associated with "chip ...hudson" match the
appropriate directory name.
Change-Id: I5e0d6d41a2e3f963760aad08ed6108acac5b66b3
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/17904
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
Commit bf264e94 (i945:) adds a PCI reset to the romstage, and commit
bc8613ec (Fix i945 based boards) fixes that to use the correct
delay of 200 ms. This code was then copied over, when adding support for
the Lenovo X60.
The reset was related to the shipped crypto card on the Roda RK886EX and
Kontron 986LCD-M, so is not needed on the Lenovo X60. So remove it.
TEST=Build and boot on Lenovo X60t.
Change-Id: Ia37d9f0ecf5655531616edb20b53757d5d47b42f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17703
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Having same memory region set as both WRPROT and WRBACK
using MTRRs is undefined behaviour. This could happen if
we allow DCACHE_RAM_BASE to be located within CBFS in SPI
flash memory and XIP romstage is at the same location.
As SPI master by default decodes all of top 16MiB below
4GiB, initial cache-as-ram line fills may have actually
read from SPI flash even in the case DCACHE_RAM_BASE was
below the nominal 4GiB - ROM_SIZE.
There are no reasons to have this as board-specific setting.
Change-Id: I2cce80731ede2e7f78197d9b0c77c7e9957a81b5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17806
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I8313ba1d93922297e5061701dad47d07617d1dcd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17804
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Iacf2e1c0b8003a3588ccbf79e17500ed12f39503
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/17786
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Instead of hardcoding pci_mmio_size in the raminit code,
this makes it a parameter in the devicetree.
A safe minimum of 768M is also defined since using anything
less causes problems (if 4G of ram is used).
Change-Id: If004c861464162d5dbbc61836a3a205d1619dfd5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16856
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Don't use scratchpad registers when we have romstage_handoff
to pass S3 resume flag. Also fixes console log from reporting
early in ramstage "Normal boot" while on S3 resume path.
Change-Id: I2f1f05ef4fc640face3d9dc92d12cfe4ba852566
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17676
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Don't use scratchpad registers when we have romstage_handoff
to pass S3 resume flag. Scratchpad register was read too
late in ramstage so acpi_is_wakeup_s3() did not evaluate
correctly.
This fixes low memory corruption at 0x1000-0x102c and the lack
of coreboot tables (util/cbmem not working) after S3 resume.
This also fixes console log from reporting early in ramstage
"Normal boot" while on "S3 resume" path.
Change-Id: I2922a15a90d2f8272c3482579bdd96f8f33e9705
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17675
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Don't use scratchpad registers when we have romstage_handoff
to pass S3 resume flag. Also fixes console log from reporting
early in ramstage "Normal boot" while on S3 resume path.
Change-Id: I4e2eabc59ff87b7ed40cfc9885bbe0256fe4a695
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17674
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapt implementation from skylake to prepare for removal of
HIGH_MEMORY_SAVE and moving on to RELOCATABLE_RAMSTAGE.
With this change, CBMEM region is set early-on as WRBACK
with MTRRs and romstage ram stack is moved to CBMEM.
Change-Id: Idee5072fd499aa3815b0d78f54308c273e756fd1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15791
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ic22beaa47476d8c600e4081fc5ad7bc171e0f903
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17735
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ifeef04b68760522ce7f230a51f5df354e6da6607
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17734
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
These headers & comments indicating a lack of functionality don't help
anything. We discourage copyrights and licenses on empty files, so
just clear these.
Change-Id: Id2ab060a2726cac6ab047d49a6e6b153f52ffe6d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17657
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Vendorcode always does PCI MMCONF access once it is
enabled via MSR.
In coreboot proper, we don't give opportunity to make
pci_read/write calls before PCI MMCONF is enabled via MSR.
This happens early in romstage amd_initmmio() for all cores.
Change-Id: If31bc0a67b480bcc1d955632f413f5cdeec51a54
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17533
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some X200 use a 4 MiB SOIC-8 flash chip.
Change-Id: Ie5bd359ef08cf1be369a026be376c21555d0ea18
Signed-off-by: Michał Masłowski <mtjm@mtjm.eu>
Reviewed-on: https://review.coreboot.org/8391
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
When MRC cache is available, first read only the SPD unique
identifier bytes required to detect possible DIMM replacement.
As this is 11 vs 256 bytes with slow SMBus operations, we save
about 70ms for every installed DIMM on normal boot path.
In the DIMM replacement case this adds some 10ms per installed DIMM
as some SPD gets read twice, but we are on slow RAM training boot path
anyways.
Change-Id: I294a56e7b7562c3dea322c644b21a15abb033870
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17491
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
USB AO is the internal name for the dedicated charging port on
ThinkPads when in S3 or lower.
AOEN (bit 0) is internal name for enabling this feature while AOCF
(bits 2 and 3) is the configuration field. According to Peter Stuge,
AOCF can be configured in this way:
00 => AC S3 S4 S4 USB on, battery S3 USB on, battery S4 S5 off
11 => AC S3 S4 S4 USB on, battery S3 S4 S5 USB off
10, 01 => equivalent to 00
This commit also adds a new configuration field in the CMOS of the
X220 and the X201 to activate this feature. It probably can be also
added to all the ThinkPads that support this functionality.
With this functionality USB devices are able to negotiate full power
from the dedicated port (usually the yellow one) even in S3.
Tested on a X201 and X220 with an Android smartphone: with this
feature enabled it shows "Charging" when connected during S3, without
it it shows "Charging slowly" (or it doesn't charge at all on the
X201).
For some reasons the "AC only" mode doesn't work, so it has been
disabled.
Change-Id: Ie1269a4357e2fbd608ad8b7b8262275914730f6e
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/17252
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The T400 features a socket P (mPGA478MN) and could potentially support
model_6fx CPUs.
Change-Id: I24f3356aa213c29011953daed31f46404e7a4d9d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17155
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Those registers are only used on more recent Intel platforms featuring a
PCH. The DP registers on G4X hardware are at a different offset.
Change-Id: Ib49e54d4e7d6595dc09fb1be35ac8178b80c7f71
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17110
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Regardless of the payload chosen a file etc/ps2-keyboard-spinup
is added to cbfs. With this fix this file is only added to cbfs when
seabios is choses as a payload.
Change-Id: I37cf4c998856db2d297356776752643dba46a8f8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16146
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Requesting low power acpi cpu c-states has two software interfaces:
Using P_LVLx I/O reads or using equivalent MWAIT requests.
This change makes it more consistent with newer targets that use MWAIT
requests.
There also exists extended intel acpi c-states which can be enabled
in two ways:
- using a substate hint to the mwait request (defined in bios);
- setting a model specific register (msr)
Currently this is done by setting the right msr bits but with this
change one can experiment by adding substate hints.
Change-Id: I9eeb5b008e2ddc2193725667f2c13582a4877e3c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14801
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The datasheets on gm45: "Mobile Intel® 4 Series Express Chipset Family"
mention the possibility of having 352M ram preallocated for the
integrated graphic device. This only worked fine if the amount of ram in
the system was 3GB or less. When 4G or more is installed, memory is
remapped to create a 1GB large pci mmio hole which is not enough and
creates conflicts when 352M vram is used.
This patch increases the pci mmio hole size on Lenovo x200 to allow
352M vram to work.
TEST: build and flash on target with 4GB ram or more, use nvramtool to
set gfx_uma_size to 352M and reboot.
Change-Id: I5ab066252339ac7d85149d91b09a9eaaaab3b5b6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16831
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Idef587d8261784e916e8d50f4336cbcfca39b9b0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16730
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I341293cd334d6d465636db7e81400230d61bc693
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16723
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Idc29373cb01f4304d22ae315812bd40f0aaa94c9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16729
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The h8s needs around 3s to respond to ps2 commands
Change-Id: I0cf01969975b8dd3839eadf90cb2dac0f1eaafc4
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16505
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Replace the use of the old device_t definition inside
mainboard/lenovo/t60.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I4d87498637d74f96ca5809b0e810755a58fc64ab
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16405
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This creates a config for the Lenovo T60 sound card based
on values taken from vendor bios
(in /sys/class/sound/hwC0D0/init_pin_configs on linux 3.16).
The sound card configuration on the vendor bios is the same
as the one on the Lenovo x60.
It improves the default behavior of the sound card:
- internal microphone is chosen by default
- when jack is inserted it is chosen instead of internal speaker
Change-Id: I44e3eaac437fe4ad97ff2b0eb32d36b33222c09b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16529
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Replace the use of the old device_t definition inside
mainboard/lenovo/x60.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: Icaceeae2fc7276efa82d37582ecac93aaf37c41c
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16372
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Uses gpio.h instead of default_southbridge_gpio_setup to configure
southbridge GPIO's. This is more consistent with how GPIO's are
configured on newer targets.
Change-Id: I6ccd0564b929e958864739b7cde04f5592c58479
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16379
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
On i945 the vram size is the default 8mb. It is also possible
to set it 1mb or 0mb hardcoding the GGC register in early_init.c
The intel documentation on i945, "Mobile Intel® 945 Express Chipset
Family datasheet june 2008" only documents those three options.
They are set using 3 bits. The documententation also makes mention
of 4mb, 16mb, 32mb, 48mb, 64mb but not how to set it.
The other non documented (straight forward) bit combinations allow
to change the VRAM size to those other states.
What this patch does is:
- add those undocumented registers with their respective vram size to
the i945 NB code;
- make this a cmos option on targets that have this northbridge.
TEST: build, flash to target, set cmos as desired and boot linux.
On Debian it can be found using "dmesg | grep stolen".
NOTE: dmesg message about reserved vram are quite different depending
on linux version
Change-Id: Ia71367ae3efb51bd64affd728407b8386e74594f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14819
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This enables the C4 low power state on the lenovo x200 and t400.
It's inspired by the thread on the mailinglist:
"[coreboot] Lenovo X200 running Coreboot drains 3-4W more power
than with Vendor BIOS".
What this does, is to enable a C3 state using MWAIT(C3) request
and set the southbridge config c4onc3_enable to automatically
upgrade C3 to the lower power C4 state.
The latency (0x37) is the same value used by the vendor bios.
With C4 enabled the idle power consumption is about ~2-3W lower.
TEST= build and install on target. Use powertop top to measure power
usage. To manually disable c-state to compare them,
do (tested on linux 4.4):
echo 1 > /sys/devices/system/cpu/cpu*/cpuidle/stateX/disable
Change-Id: I1a1663a7662ebc7157a965667680688ad6a33545
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15251
Tested-by: build bot (Jenkins)
Reviewed-by: Swift Geek
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector
code) the reboot counter stored in `reboot_bits` isn't reset on a reboot
with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR
enabled, later stages (e.g. payload, OS) have to clear the counter too,
when they want to switch to normal boot. So change the bits to (h)ex
instead of (r)eserved.
To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also
remove all occurences of the obsolete `last_boot` bit that have sneaked
in again since 24391321 (mainboard: Remove last_boot NVRAM option).
Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16157
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ia1f24d328a065a54975adde067df36c5751bff2d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/15987
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I5a6d41f815f65719780499fa18c131311a9dc8f7
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16136
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add GPIOs initialisation before dock check.
Needed in order to properly detect the presence or absence of the lenovo
dock.
Previously the check always reported the dock as connected and currently
it always reports it as disconnected since the GPIOs are not properly
initialised during the check.
Tested and confirmed working.
Change-Id: I7fbf8c2262a1eb5dee9cbe5e23bf44f7f8181009
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16139
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
I'm not sure if that's the right fix here, but assuming the bit mask is
right, the inb is wrong.
Change-Id: I7e33019af088780a09be12513200bec63734bf97
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1229556
Reviewed-on: https://review.coreboot.org/16026
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Change-Id: I7930d5cded290f2605d0c92a9c465a3f0c1291a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15974
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Run the command below to format the files `irq_tables.c` of (mostly AMD)
mainboards correctly with GNU indent 2.2.10.
```
$ git grep -l 'if (sum != pirq->checksum) {' | xargs indent -l
```
Fix up the following two checkpatch.pl errors manually.
```
ERROR: that open brace { should be on the previous line
#1219: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:129:
+ uint8_t reg[8] =
+ { 0x41, 0x42, 0x43, 0x44, 0x60, 0x61, 0x62, 0x63 };
ERROR: that open brace { should be on the previous line
#1221: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:131:
+ uint8_t irq[8] =
+ { 0x0A, 0X0B, 0X0, 0X0a, 0X0B, 0X05, 0X0, 0X07 };
```
This is needed, so that follow-up commits, fixing checkpatch.pl errors
and warnings, won’t run into conflicts with the git commit hooks, when
for example, spaces instead of tabs are used for indentation.
Change-Id: If254723f3013377fb3b9b08dd5eca6b76730ec4a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/15932
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I6d51f46240c62fcd6089411e8681e0b6e7d5bfe4
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/15222
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I3cffe9d832edbbea79cabca639d9d920b7ffcf9a
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/8178
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ic82a732ba28ba24e42a635539cca3d76128b40b5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15247
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I3148dbbcb06676f48b6bc357124403b70b9bcb6a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15246
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I616143b55d7c5726dc2475434e3fcb08b8d69bda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15230
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|