Age | Commit message (Collapse) | Author |
|
There is a whole bunch of pads being configured by the vendor firmware
that are either unconnected due to unpopulated resistor pads, only
connected to test points for vendor debugging purposes or just used as
strap. Configure them as NC with an appropriate pull to disable the
RX/TX functions.
The pads have been determined by dissecting a dead board.
This patch has been tested thoughroughly on a machine, normally used
productive, to see if any issues arise. No problems occurred at all.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I06b942e3182469f87e41914c893e5b485ccca420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow vendor and enable Advanced Error Reporting for PCIe root ports.
This enabled the Linux AER driver, which handles PCIe error conditions.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9d9b5afca0ca891e2812445db1d42a46ba16199e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48369
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the subsystem ids to PCI ports and devices, which were dumped on
vendor firmware using `lspci`.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Idb36c5c72e1b0b8303439ae5dce772822f551d2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48368
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow vendor and enable LTR on all root ports to optimize for devices'
latency requirements and also optimize power management while preventing
failure due to wrongly guessing idle states, which happens without LTR.
Tested successfully. No errors show up in dmesg.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8f72087c71e291d2412dc7b3e16ee7f419e2ca0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48367
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All X11 boards currently supported have Intel SPS without support for
S3/S5. Thus, drop it from Kconfig.
Note: not all X11 boards are server boards. When a X11 desktop or
workstation board should be added, this can be selected by the boards,
where S3/S5 work.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ie75c9217078d38c42eba2b30c078b8bb1c2ca694
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Correct unconnected pads that are configured different currently by
copying vendor configuration while porting the board.
Add internal pull resistors to all unconnected pads, that do not have an
external pull resistor, to prevent floating.
The pads have been determined by dissecting a dead board. This commit
only changes pads, that are not connected at all and don't have any via,
so we can be absolutely sure there is no other connection.
Change-Id: I991fe270b42f430f7447712236e0f80b3d5bba2a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
(Re)configure various pads found by dissecting a dead board and vendor
firmware, as well as the BMC firmware:
- GPP_B14: input connected to jumper JBR1 - could be used to implement
"BIOS Recovery" ("Top-Block Swap") functionality; external pull-up
- GPP_C20: output to BMC alert CPU_THROTTLED# - can be used to notify
the BMC about a thermal throttling event. Not implemented in vendor
firmware.
- GPP_C23: input connected to the CPU's CATERR# output; external pull-up
Not actively used by vendor firmware.
- GPP_D1: output connected to on-board and front panel power LEDs
- GPP_D18: output connected to PERST# of both CPU PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D19: output connected to PERST# of both PCH PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D22: input connected to the BMC enable/disable jumper JPB1; Will
be used later in CB:48096 and CB:48097; external pull-up
- GPP_G0 - GPP_G3: dedicated/integrated CPU switching; probably not
useful, since the IGD is not connected to any ports on this board.
External pulls ensure correct function of a dGPU even without driving
the gpios. Not used by vendor firmware.
- GPP_G12 - GPP_G16: inputs for binary SKU_ID; external pulls
- GPP_G20: PWRFAIL# input from JPI2C1 (pin 3); external pull-up; Not
used by vendor firmware.
Also add comments for documentation. While at it, mark ME-owned pads as
reserved.
Change-Id: I9f9328e9ce6f7e291b171f776bb98bc617b64b93
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
SATA_AHCI is already the default mode for SKL/KBL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: Ib5222c1b0314365b634f8585e8a97e0054127fe9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48378
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Skylake FSP isn't used by coreboot anymore. Therefore, drop the
misleading comment and the "KBLFSP" extension from the names of these
enums.
Also, drop the "MODE" extension to make their names shorter in general,
since it doesn't add any more value.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: If37d40e4e1dfd11e9315039acde7cafee0ac60f0
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48377
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All four SMI/NMI interrupt inputs have an external pull-up resistor and
get triggered by pulling the line low. Thus, correct the trigger to
active-low.
Also document the signals by adding appropriate comments.
The pads' connections have been determined by dissecting a dead board.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Id1a8c1e0b9fe723a15d04a88d565a53eeba9b085
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48093
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop the NMI overrides, since NMI now gets configured in gpio common
code. Also remove the variant init mechanism, which is unused now.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I02e0c679f9aafe33108320a8dfc62dcb278202ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48092
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the FADT PM profile to ENTERPRISE_SERVER, since the currently
supported X11 boards are server boards.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8fb5c7c262fbd3f3c085d7c2e2ef3d6ff6ce73eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48088
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rework gpio setup for the board series to not use headers but
stage-specific compilation units.
Tested successfully on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ic62ce4335af605c081ef288e892441585ff2bd3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
GPIO needs to be initialized before the IPMI device gets initialized,
so the GPIOs can be read/set by the code in CB:48096 and CB:48094. Thus,
use mainboard_ops.init for GPIO configuration instead of using the
indirection via a mainboard_enable function.
To make it more visible, that we use chip.init, rename `mainboard_init`
to `mainboard_chip_init`.
Tested successfully on X11SSM-F including the IPMI changes.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I192e69a34fa262b38bc40a95fb11c22a4041d0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The ITSS override is not needed for LPC_CLKOUT* pads. Drop it.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I3dbbc8944751779151dcd4f92fb870d937801d69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48084
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move gpio configuration from the Fsp callback to mainboard init.
Tested successfully on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: If2a54c75c5243d94cdc025c597ee347820b35d32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48086
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop zero-value devicetree options and move PcieRpEnable options down to
the corresponding devices.
Test: built with TIMELESS=1; binaries remain identical
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9285d786e973621a732e2627c734adc930e54207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Drop the TODO comment, since there is no TODO left. Also drop the now
obsolete TODO section from the board documentation.
Change-Id: I4192aaedc1429c8ff1bd7c52baa4741e1df0d0c5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Time has shown that using spaces never converges into proper alignment.
Change-Id: I5338aeaf139580f9eab3e1e02cb910080a95d2c2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Most of these comments have been copy-pasted or serve no purpose other
than to eventually turn into misleading info. While the description of
the first 120 bits of CMOS could be useful, it should instead be added
to the documentation for the CMOS option infrastructure, or /dev/null.
Moreover, trim down newlines to no more than two consecutive newlines.
Change-Id: I119b248821221e68c4e31edba71ba83b7d2e14e9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Change-Id: I50390f66d9570eb0fd703e3ad8a2735125d76b61
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47566
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5b6191d2b5f6fd6d127934eda56e3c24181b0c4c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47565
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Google Wolf remains identical.
Change-Id: I710581156937b042ba4cf5948c65d0795ad37bbf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46789
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The other two modes are not used by any mainboard, and the code seems to
be copied from older southbridges. As the code looks incorrect, drop it.
Change-Id: I374546279a85cead1aea13e0952bbfd6f643a75b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Following commit f50ea988b a couple of symbols are gone, so follow up
that change for this board as well.
Change-Id: I09fd3a107447eb45bb46b7f0f821377943f140b2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46621
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This adds another X11 series board, the X11SSH-F, which is similiar to
X11SSH-TF but differs in PCIe interfaces/devices, ethernet interfaces.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I92c32bff861f0b5697aea52ff282fae76b3b78ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
There's no need to have multiple Kconfig symbols which do the same
thing. Introduce `SUPERIO_NUVOTON_COMMON_COM_A` and update boards to use
the new symbol. To preserve alphabetical order in mainboard Kconfig,
place the new symbol above the Super I/O symbol (instead of below).
Change-Id: Ic0a30b3177a1a535261525638be301ae07c59c14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46522
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5a5f4e7067948c5cc7a715a08f7a5a3e9b391191
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch moves platform.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify _PIC method present inside
common platform.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I5189b03d6abfaec39882d28b40a9bfa002128be3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I1aae6c0291ad329c8cc125cd18ba22dfd63d979b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
CPU_INTEL_HASWELL is already selected at nb/intel/haswell/Kconfig.
Change-Id: I608286aae72bc740be642a72109472fb235f37bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Change-Id: I6afea5c102299e570378a1656d3dcd329a373399
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44093
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, SDXC gets enabled by the option ScsSdCardEnabled,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SDXC controller.
All corresponding mainboards were checked if the devicetree
configuration matches the ScsSdCardEnabled setting, and missing
entries were added.
Change-Id: I298b7d0b0fe2a7346dbadcea4be22dc67fce4de8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SA thermal subsystem gets enabled by the option Device4Enable,
but this duplicates the devicetree on/off options. Therefore depend on
the devicetree for enablement of the SA thermal subsystem controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Device4Enable setting, and missing entries
were added.
Change-Id: I7553716d52743c3e8d82891b2de14c52c6d8ef16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44026
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
They default to zero already, so we might as well drop them.
Tested with BUILD_TIMELESS=1, its coreboot.rom does not change.
Change-Id: I3c04240b270f51d584f879e1344301679f133fdb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43928
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently eMMC gets enabled by the option ScsEmmcEnabled, but this
duplicates the devicetree on/off options. Therefore use the
on/off options for the enablement of the eMMC controller.
I checked all corresponding mainboards if the devicetree configuration
matches the ScsEmmcEnabled setting.
Change-Id: I3b86ff6e2f15991fb304b71d90c1b959cb6fcf43
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SMBus gets enabled by the option SmbusEnable, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SMBus controller.
I checked all corresponding mainboards if the devicetree configuration
matches the SmbusEnable setting.
Change-Id: I0d9ec1888c82cc6d5ef86d0694269c885ba62c41
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SATA gets enabled by the option EnableSata, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SATA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableSata setting.
Change-Id: I217dcb7178f29bbdeada54bdb774166126b47a5a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Add interrupts for all enabled superio devices to quiet the warning
about missing interrupts in devicetree.
Vendor uses interrupt 0x00 for all devices except SUART* and KBC, so
let's do that, too. This also changes SWC from 0x0b to 0x00.
Verified with superiotool on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I7a6dc7345f020e53415a7d0d104ce93ab4b194fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonas Löffelholz
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
All boards disable PIRQs. They aren't used on modern OSes anyway.
Change-Id: I1351fd4a3910e8cf2e9afe51dc2e82c7464de403
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
If bit 7 of a PIRQ route is set, it is disabled. Modern OSes don't use
PIRQ routing, so we might as well zero the other bits for consistency.
Tested on Asrock B85M Pro4 with SeaBIOS 1.13.0, still boots.
Change-Id: I78980b9ea5e878a6200df0f6c18c5e7d06a7950a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43861
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Put them in common code just in case something depends on the values.
Change-Id: Ief526efcbd5ba5546572da1bc6bb6d86729f4e54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43851
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- remove comments (except the GPIO group), because it does not contain
useful information that helps to understand the circuit, which we do
not have;
- remove empty lines between macros;
- use a shorter PAD_CFG_GPI_INT() macro instead of
PAD_CFG_GPI_TRIG_OWN() to set DRIVER mode.
Change-Id: Ia7111341aab6f400da70d936849e4d4c9406905b
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Converts bit field macros to target PAD_CFG_*() macros, which were
hidden in the comments. To do this, the following command was used:
./intelp2m -n -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h
./intelp2m -n -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Tested with BUILD_TIMELESS=1, Supermicro X11SSH-TF and X11SSM-F,
remains identical.
Change-Id: Idad7536854d4b1ae7dcf7934e81de438478fe059
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35679
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fixes some bit fields to convert to target macros PAD_CFG_*() macros.
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Change-Id: I291f5f0f34505c466b610aa4049c8cc35937d140
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42918
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch excludes bit fields that should be ignored [1] in order
to convert current macros to target PAD_CFG_*() macros. The following
commands were used for this:
./intelp2m -ii -fld cb -ign -t 1 -p snr -file ../../src/mainboard/
supermicro/x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h
/intelp2m -ii -fld cb -ign -t 1 -p snr -file ../../src/mainboard/
supermicro/x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h
[1] ignore RX Level/Edge Configuration (bit 26:25) and RX/TX Buffer
Disable (bit 9:8) for the native function, because it does not
affect the pad in this mode.
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Change-Id: Icdf366a8d416598cec5afcb9a0fae6bf7ecd7ba0
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42917
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|