summaryrefslogtreecommitdiff
path: root/src/soc/intel/skylake
AgeCommit message (Collapse)Author
2017-11-28soc/intel/skylake: Make use of Intel common DSP blockSubrata Banik
TEST=Build and boot soraka/eve. Change-Id: I8be2a90dc4e4c5eb196af57045d2a46b7f0c9722 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22609 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-11-15soc/intel/skylake: Make use of common CSE code for skylakeSubrata Banik
TEST=Ensures global reset could able to reset system. Change-Id: I11ce1812a5a0aa2da6b414555374460d606e220e Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22395 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-11-15soc/intel: Enable ACPI DBG2 table generationDuncan Laurie
Enable the ACPI DBG2 table generation for Intel boards. This is a Microsoft defined ACPI extension that allows an OS to know what the debug port is on a system when it is not enabled by the firmware, so it does not show up in the coreboot tables and cannot be easily found by a payload. broadwell: Use byte access device, set up only when enabled since it relies on the port being put in byte access mode and using this serial port for debug was not standard in this generation. skylake: Enable for the configured debug port. Skylake uses intelblocks for UART but not ACPI. common: Enable for the configured debug port. This affects apollolake and cannonlake. Tested by compiling for apollolake/broadwell, tested by reading the DBG2 ACPI table on kabylake board and using IASL to dump: [000h 0000 4] Signature : "DBG2" [004h 0004 4] Table Length : 00000061 [008h 0008 1] Revision : 00 [009h 0009 1] Checksum : 3B [00Ah 0010 6] Oem ID : "CORE " [010h 0016 8] Oem Table ID : "COREBOOT" [018h 0024 4] Oem Revision : 00000000 [01Ch 0028 4] Asl Compiler ID : "CORE" [020h 0032 4] Asl Compiler Revision : 00000000 [024h 0036 4] Info Offset : 0000002C [028h 0040 4] Info Count : 00000001 [02Ch 0044 1] Revision : 00 [02Dh 0045 2] Length : 0035 [02Fh 0047 1] Register Count : 01 [030h 0048 2] Namepath Length : 000F [032h 0050 2] Namepath Offset : 0026 [034h 0052 2] OEM Data Length : 0000 [036h 0054 2] OEM Data Offset : 0000 [038h 0056 2] Port Type : 8000 [03Ah 0058 2] Port Subtype : 0000 [03Ch 0060 2] Reserved : 0000 [03Eh 0062 2] Base Address Offset : 0016 [040h 0064 2] Address Size Offset : 0022 [042h 0066 12] Base Address Register : [Generic Address Structure] [042h 0066 1] Space ID : 00 [SystemMemory] [043h 0067 1] Bit Width : 00 [044h 0068 1] Bit Offset : 00 [045h 0069 1] Encoded Access Width : 03 [DWord Access:32] [046h 0070 8] Address : 00000000FE034000 [04Eh 0078 4] Address Size : 00001000 [052h 0082 15] Namepath : "\_SB.PCI0.UAR2" Change-Id: If34a3d2252896e0b0f762136760ab981afc12a2f Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/22453 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-11soc/intel/skylake: Make use of Intel SPI common blockSubrata Banik
TEST=Build and boot soraka/eve Signed-off-by: Subrata Banik <subrata.banik@intel.com> Change-Id: I10de3ff75a3b063c4c46471e380bbbe2630c35f3 Reviewed-on: https://review.coreboot.org/22361 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-11-11soc/intel/{cannonlake,skylake}: Add _soc_ prefix in spi soc routineSubrata Banik
This ensures that function callback into the SoC code. Change-Id: Idc16d315ba25d17a2ab537fcdf0c2b51c8802a67 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22392 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-11-07soc/intel/kabylake: Add Dialog da7219 NHLT blob supportNaveen Manohar
Add APIs and required parameters for creating Dialog da7219 SSP endpoints in NHLT table. The use of a NHLT table is required to make audio work on the kabylake SoCs employing the internal DSP. The table describes the audio endpoints (render vs capture) along with their supported formats. BUG=b:68686020 TEST=check that NHLT table for da7219 is created properly Change-Id: I57b88873f1c59c8aadf8eec3c80a9d95165a2cc3 Signed-off-by: Naveen Manohar <naveen.m@intel.com> Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/22324 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-04sb and soc: Enforce correct offset of member "chromeos" in global_nvs_tJonathan Neuschäfer
The padding has recently been broken in commit 90ebf96df5 ("soc/intel/skylake: Add GNVS variables and include SGX ASL") and fixed again in commit af88398887 ("soc/intel/skylake: Fix broken GNVS offset for chromeos"). Avoid this bug in the future. Change-Id: I1bf3027bba239c8747ad26a3130a7e047d3b8c94 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/22229 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-11-04soc/intel/skylake: Update coding style for i2cLijian Zhao
From comment from https://review.coreboot.org/#/c/22238/, the coding style need to be update. TEST=N/A Change-Id: Id022648951c0f11216aa32f422b5095476f82f8c Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/22278 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-10-25soc/intel/skylake: Fix broken GNVS offset for chromeosFurquan Shaikh
Change 90ebf9 (soc/intel/skylake: Add GNVS variables and include SGX ASL) added new GNVS variables but did not adjust the unused array size and thus broke chromeos offset. This change fixes the above issue by reducing the size of unused array. BUG=b:68254376 TEST=Verified that chromeos offset is correct. crossystem is able to read all variables. Change-Id: I5f76f5bba4f0f50a23a863450743385ad2a82b2b Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22176 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-10-22security/vboot: Move vboot2 to security kconfig sectionPhilipp Deppenwiese
This commit just moves the vboot sources into the security directory and fixes kconfig/makefile paths. Fix vboot2 headers Change-Id: Icd87f95640186f7a625242a3937e1dd13347eb60 Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org> Reviewed-on: https://review.coreboot.org/22074 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-10-22soc/intel/skylake: pass SataSpeedLimit param to FSP2Matt DeVillier
The Librem13v2 needs to set this parameter to work around power-related issues with some SATA devices. Change-Id: I7fcef36ec8662e18834394b72427a0633c6b7e92 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/22045 Reviewed-by: Youness Alaoui <snifikino@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-22skylake/me: Add debug output of HFST registersYouness Alaoui
The ME status is the interpretation of the status registers, but having the actual status registers printed is important and it doesn't hurt to show them. Change-Id: I6ef3401b36fedfa8aed14f4a62bdbec3d8c6d446 Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/21960 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-10-20soc/intel/skylake: update GNVS with SGX dataPratik Prajapati
- Call sgx_fill_gnvs to update GNVS data, if CONFIG_SOC_INTEL_COMMON_BLOCK_SGX is set. - With this patch SGX ACPI device would get pached with enumaretd values of ECP device status, base address and length Change-Id: Ief0531fbab34838a3f8adb9cdc7d3fe19203c432 Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com> Reviewed-on: https://review.coreboot.org/21972 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-20soc/intel/skylake: Add GNVS variables and include SGX ASLPratik Prajapati
- Add GNVS variables for SGX - Include SGX ASL if CONFIG_SOC_INTEL_COMMON_BLOCK_SGX is set - With this patch SGX ACPI device would get created and kernel SGX driver would let loaded Change-Id: Ie95eb79a01e1c0005e0f137b015b7fe000c1ab2a Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com> Reviewed-on: https://review.coreboot.org/21971 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-19soc/intel/skylake: Use EBDA structure to store soc reserve memory sizeSubrata Banik
Avoid calling calculate_dram_base() function to get chipset reserved memory size during pci resource allocation. Rather use EBDA to store chipset reserved memory size while calling cbmem_top_int(). This patch avoids one extra calculate_dram_base() call. BRANCH=none BUG=b:63974384 TEST=Ensures DRAM based resource allocation has taken care of Intel SoC reserved ranges. Change-Id: I52f359db5a712179d7f2accb4d323d759f3b052b Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22098 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-19soc/intel/skylake: Probe XHCI for wake source for Internal PMEFurquan Shaikh
If GPE_STS indicates that the wake source is internal PME, but none of the controllers have the PME_STS bit set, then try probing individual XHCI ports to see if one of those was a wake source. In some cases e.g. gsmi logging with S0ix, pci_pm_resume_noirq runs before gsmi callback and clears PME_STS_BIT in controller register. In such cases, xhci port status might provide a better idea about the wake source. BUG=b:67874513 Change-Id: I841bb2abccfa9bd6553c1513e88a6306b40315e4 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22089 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-19soc/intel/skylake: Prevent false logs in pch_xhci_port_wake_checkFurquan Shaikh
1. Ensure that port_status read is not all 1s to ensure that read from mmio address returned valid data. 2. If device connect/disconnect shows that it was a wake source, there is no need to check for usb activity. BUG=b:67874513 Change-Id: Id8b4a1fec7bfe530fe435a0f52944b273cdd89ad Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22088 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-19soc/intel/skylake: Define mask for SMI handlers that can be run in SCI modeFurquan Shaikh
This change adds a mask to allow SMI handlers to be run even in SCI mode. This prevents any SMI handlers from accidentally taking unnecessary action in SCI mode. Add APM_STS and SMI_ON_SLP_EN_STS to this mask to allow gsmi and sleep to work in SCI mode. BUG=b:67874513 Change-Id: I298f8f6ce28c9746cbc1fb6fc96035b98a17a9e3 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22087 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-19soc/intel/skylake: Support logging wake source in SMMFurquan Shaikh
This change adds support for logging wake source information in gsmi callbacks. With this change, all the elog logging infrastructure can be used for S0ix as well as S3 on skylake. BUG=b:67874513 Change-Id: Ie1f81e956fe0bbe2e5e4c706f27997b7bd30d5e0 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22086 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-19soc/intel/skylake: Move power_state functions to pmutil.cFurquan Shaikh
This change moves soc_fill_power_state and soc_prev_sleep_state to pmutil.c. It allows the functions to be used across romstage and smm. BUG=b:67874513 Change-Id: I375ac029520c2cdd52926f3ab3c2d5559936dd8c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22085 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-10-19soc/intel/skylake: Use PCH_DEV_* instead of PCH_DEVFN_*Furquan Shaikh
This change allows the same functions to be used across ramstage and smm without having to add checks for what stage is using it. BUG=b:67874513 Change-Id: I3b10c9e8975e8622d8cb0f66d90d39a914ba7e1c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22084 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-19soc/intel/skylake: Use newly added pmc_read_pm1_controlFurquan Shaikh
BUG=b:67874513 Change-Id: I298065f30647ae9bba8f6a8481bd34eec64f1d8e Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22083 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-16soc/intel/common: sanity check ebda signatureAaron Durbin
It's possible for chipsets utilizing ebda to cache the cbmem_top() value to be called prior to the object being entirely setup. As such it's important to check the signature to ensure the object has been initialized. Do that in a newly introduced function, retrieve_ebda_object(), which will zero out the object if the signature doesn't match. Change-Id: I66b07c36f46ed9112bc39b44914c860ba68677ae Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/21995 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
2017-10-16console/flashconsole: Enable support for postcarYouness Alaoui
If FSP 2.0 is used, then postcar stage is used and the flashconsole as well as spi drivers needed to be added. Change-Id: I46d720a9d1fe18a95c9407d08dae1eb70ae6720e Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/21959 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-16src/soc/skylake: Fix Null pointer dereferencesShaunak Saha
Fix bug detected by coverity to handle the NULL pointer dereference Coverity Issues: * 1379849 * 1379848 TEST=Build and run on skylake platform Change-Id: Iec7a88a03531bbfeb72cedab5ad93d3a4c23eef5 Signed-off-by: Shaunak Saha <shaunak.saha@intel.com> Reviewed-on: https://review.coreboot.org/21909 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-10-14intel/skylake: Use Sata related registers from devicetreeYouness Alaoui
Enable the use of the SataPortsEnable and SataPortsDevSlp registers which were being ignored from the devicetree and were not affecting the resulting UPD parameters. SataPortsEnable was only being copied for the first SATA port, while the other ports were left ignored. Change-Id: Iae70a4d6375fa5d1b05ee89f6b97c65dbbf28dda Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/21958 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-10-12soc/intel/common: Clean up PMC library GPE handling APIFurquan Shaikh
1. Update gpe handling function names to explicitly mention if they are operating on: a. STD GPE events b. GPIO GPE events c. Both 2. Update comment block in pmclib.h to use generic names for STD and GPIO GPE registers instead of using any one platform specific names. BUG=b:67712608 Change-Id: I03349fe85ac31d4215418b884afd8c4b531e68d3 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/21968 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-10-10soc/intel/skylake: Fix broken suspend/resume for deep S3Furquan Shaikh
Change d3476809 (soc/intel/skylake: Add support in SKL for PMC common code) changed the logic for obtaining previous sleep state by unconditionally checking for PWR_FLR and SUS_PWR_FLR. In case of deep S3, SUS_PWR_FLR is set in gen_pmcon_b (just like resume from deep S5/G3) and hence the check for power failure should be done only when WAK_STS bit is not set. This is necessary to differentiate wakes from deep S3 and G3. This change restores the original logic by performing power failure check only in cases where WAK_STS bit is not set. BUG=b:67617726 TEST=Verified following: 1. When WAK_STS bit is not set and SUS_PWR_FLR is set, coreboot correctly identifies that the system prev sleep state was S5. 2. When WAK_STS bit is set and SUS_PWR_FLR is set, coreboot correctly identifies that the system prev sleep state was S3. Change-Id: Ic97bbc9911ba34aa21f4728c77fc20c5bb08f6f9 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/21931 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Shaunak Saha <shaunak.saha@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-06soc/intel/skylake: use locate_vbt directly instead of calling a wrapperPatrick Georgi
Change-Id: I65c423660ab1778f5dd9243e428a4d005bd1699a Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/21898 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-05soc/intel/skylake: Add support in SKL for PMC common codeShaunak Saha
Change-Id: I3742f9c22d990edd918713155ae0bb1853663b6f Signed-off-by: Shaunak Saha <shaunak.saha@intel.com> Reviewed-on: https://review.coreboot.org/20499 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-10-05soc/intel/skylake: Add config for mbx command for Intersil VR C-state issuesRizwan Qureshi
Config for activating VR mailbox command for Intersil VR C-state issues. 0 - no mailbox command sent. 1 - VR mailbox command sent for IA/GT rails only. 2 - VR mailbox command sent for IA/GT/SA rails. BUG=b:65499724 BRANCH=none TEST= build and boot soraka. Change-Id: Ibcced31b7ba473ffa7368c90c945d07a81a368d4 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/21680 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-10-05vendor/intel/skykabylake: Update FSP header files to version 2.7.2Balaji Manigandan B
Update FSP header files to version 2.7.2. New UPDs added FspmUpd.h: *CleanMemory FspsUpd.h: *IslVrCmd *ThreeStrikeCounterDisable Structure member names used to specify memory configuration to MRC have been updated, SoC side romstage code is updated to handle this change. CQ-DEPEND=CL:*460573,CL:*460612,CL:*460592 BUG=b:65499724 BRANCH=None TEST= Build and boot soraka, basic sanity check and suspend resume checks. Change-Id: Ia4eca011bc9a3b1a50e49d6d86a09d05a0cbf151 Signed-off-by: Balaji Manigandan B <balaji.manigandan@intel.com> Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/21679 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-10-03soc/intel/skylake: Enable common LPC IPRavi Sarawadi
Enable Skylake to use the new common LPC code. This will help to reduce code duplication and streamline code bring up. Change-Id: I042e459fb7c07f024a7f6a5fe7da13eb5f0dd688 Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com> Reviewed-on: https://review.coreboot.org/20120 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-02soc/intel/skylake: Use common/block/gpioHannah Williams
Other than switch to use common gpio implementation for skylake based platform, also apply the needed changes for purism board. Change-Id: I06e06dbcb6d0d6fe277dfad57b82aca51f94b099 Signed-off-by: Hannah Williams <hannah.williams@intel.com> Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/19201 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Youness Alaoui <snifikino@gmail.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-27soc/intel/skylake: Remove CCA object for IMGU and CIO2 devicesV Sowmya
IMGU and CIO2 devices do support the hardware managed cache coherency and hence removing the CCA object which was reporting that cache coherency is not supported. BUG=none BRANCH=none TEST=Build and boot soraka. Dump ACPI tables and verify that CCA object is not present. Change-Id: I14b0a92eafe193e9004d2dad0957a3fe8d05d313 Signed-off-by: V Sowmya <v.sowmya@intel.com> Reviewed-on: https://review.coreboot.org/21678 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-22soc/intel/skylake: Calculate soc reserved memory sizeSubrata Banik
This patch implements soc override function to calculate reserve memory size (PRMRR, TraceHub, PTT etc). System memory should reserve those memory ranges. BRANCH=none BUG=b:63974384 TEST=Ensures DRAM based resource allocation has taken care of intel soc reserved ranges. Change-Id: I19583f7d18ca11c3a58eb61c927e5c3c3b65d2ec Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/21540 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-09-22soc/intel/skylake: Use EBDA area to store cbmem_top addressSubrata Banik
This patch uses BIOS EBDA area to store relevent details like cbmem top during romstage after MRC init is done. Also provide provision to use the same EBDA data across various stages without reexecuting memory map algorithm. BRANCH=none BUG=b:63974384 TEST=Ensures HW based memmap algorithm is executing once in romstage and store required data into EBDA for other stage to avoid redundant calculation and get cbmem_top start from EBDA area. Change-Id: Ib1a674efa5ab3a4fc076fc93236edd911d28b398 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/21424 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-22soc/intel/skylake: Refactor memory layout calculationSubrata Banik
This patch split entire memory layout calculation into two parts. 1. Generic memory layout 2. SoC specific reserve memory layout. usable memory start = TOLUD - Generic memory size - - soc specific reserve memory size. Change-Id: I510d286ce5e0d8509ec31a65e971d5f19450364f Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/21537 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-22soc/intel/skylake: add Kabylake Celeron base SKUGaggery Tsai
This patch adds the support for Kabylake Celeron base SKU with PCH ID 0x9d50. BRANCH=none BUG=b:65709679 TEST=Ensure coreboot could recognize the Kabylake Celeron base SKU and boot into OS. Change-Id: I9c6f7bf643e0dbeb132fb677fcff461244101a55 Signed-off-by: Tsai, Gaggery <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/21617 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: David Wu <david_wu@quantatw.com> Reviewed-by: T.H. Lin <T.H_Lin@quantatw.com>
2017-09-21soc/intel/skylake: Add config for enabling LTR for PCIe Root portRizwan Qureshi
There are a lot errors reported by AER driver for root port 0. The erors are being caused by an unsupported request from the device to the upstream port. Enabling LTR on the root port stops these errors, it is because LTR is enabled on the device side but not on the root port and hence root port was logging the LTR messages from the device as unsupported. The PCIe base spec (v3.1a) section 6.18 also states that: LTR support is discovered and enabled through reporting and control registers described in Chapter 7. Software must not enable LTR in an Endpoint unless the Root Complex and all intermediate Switches indicate support for LTR. Note that it is not required that all Endpoints support LTR to permit enabling LTR in those Endpoints that do support it. When enabling the LTR mechanism in a hierarchy, devices closest to the Root Port must be enabled first. If an LTR Message is received at a Downstream Port that does not support LTR or if LTR is not enabled, the Message must be treated as an Unsupported Request. FSP has a UPD for enabling/disabling LTR on root port, use the same for configuring LTR on PCIe root ports. BUG=b:65570878 TEST=After enbaling LTR on port 0 on the MB devicetree, No errors reported by AER driver for root port 0. Change-Id: Ica97faa78fcd991dad63ae54d2ada82194b4202a Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/21547 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-20vboot: reset vbnv in cmos when cmos failure occursAaron Durbin
There's an occasional issue on machines which use CMOS for their vbnv storage. The machine that just powers up from complete G3 would have had their RTC rail not held up. The contents of vbnv in CMOS could pass the crc8 though the values could be bad. In order to fix this introduce two functions: 1. vbnv_init_cmos() 2. vbnv_cmos_failed() At the start of vboot the CMOS is queried for failure. If there is a failure indicated then the vbnv data is restored from flash backup or reset to known values when there is no flash backup. BUG=b:63054105 Change-Id: I8bd6f28f64a116b84a08ce4779cd4dc73c0f2f3d Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/21560 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-09-20soc/intel/skylake: refactor rtc failure checkingAaron Durbin
In order to prepare for checking RTC failure in the early boot paths move the rtc failure calculation to pmutil.c and add a helper function to determine if failure occurred. BUG=b:63054105 Change-Id: I88bf9bdba8c1f3a11bc8301869e3da9f033ec381 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/21554 Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-09-20vboot: remove init_vbnv_cmos()Aaron Durbin
Instead of having each potential caller deal with the differences of cmos_init() and init_vbnv_cmos() when VBOOT is enabled put the correct logic within the callee, cmos_init(), for handling the vbnv in CMOS. The internal __cmos_init() routine returns when the CMOS area was cleared. BUG=b:63054105 Change-Id: Ia124bcd61d3ac03e899a4ecf3645fc4b7a558f03 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/21549 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-09-15soc/intel/skylake: Move UNCORE PRMRR base and mask defines.Pratik Prajapati
UNCORE PRMRR BASE and MASK MSRs are not common, so move to SOC specific header file and rename the #define to start with MSR_* Change-Id: I799c43f0b7a9eec5b3b69ab0f5100935c7f3f170 Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com> Reviewed-on: https://review.coreboot.org/21247 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-15soc/intel/common/sgx: Define and use soc_fill_sgx_param()Pratik Prajapati
To remove chip.h dependency from SGX common code - Create API soc_fill_sgx_param() and use it in sgx.c - Implement same API for skylake/kabylake - define sgx_param structure Also include intelblocks/sgx.h instead of soc/msr.h Change-Id: I358f0817bec5dd6cd147a645675b5688969a04e0 Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com> Reviewed-on: https://review.coreboot.org/21528 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-14soc/intel/skylake: Implement UNCORE PRMRR get base and mask APIPratik Prajapati
Implement soc_get_uncore_prmmr_base_and_mask() API for SKL/KBL Change-Id: I880d3d88138809cdf030507877079cbea52a0d97 Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com> Reviewed-on: https://review.coreboot.org/21245 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-09-14device: acpi_name() should take a const struct deviceAaron Durbin
There's no reason to mutate the struct device when determining the ACPI name for a device. Adjust the function pointer signature and the respective implementations to use const struct device. Change-Id: If5e1f4de36a53646616581b01f47c4e86822c42e Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/21527 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-09-11soc/intel/skylake: Fix SPI WP disable status checkRavi Sarawadi
Use SPI write protect disable bit from BIOS_CONTROL register to check write protect status. Change-Id: Ie79fb4e3e92a4ae777c5d501abbb44a732a9862a Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com> Reviewed-on: https://review.coreboot.org/21449 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-09-11cpu/x86/mp_init: remove adjust_cpu_apic_entry()Aaron Durbin
The original purpose of adjust_cpu_apic_entry() was to set up an APIC map. That map was effectively only used for mapping *default* APIC id to CPU number in the SMM handler. The normal AP startup path didn't need this mapping because it was whoever won the race got the next cpu number. Instead of statically calculating (and wrong) just initialize the default APIC id map when the APs come online. Once the APs are online the SMM handler is loaded and the mapping is utilized. Change-Id: Idff3b8cfc17aef0729d3193b4499116a013b7930 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/21452 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2017-09-08soc/intel/skylake: Create acpi_get_sleep_type() to get previous sleep stateSubrata Banik
This patch implements soc function to get previous sleep state using chipset_power_state global structure. acpi_get_sleep_type is needed in PRE_RAM stage when soc selects CONFIG_EARLY_EBDA_INIT kconfig option. Change-Id: I79acbfc09c8d255fbf9d73e49e8c7764f3f3fac6 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/21423 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-29 16:31:41 +0000