| Age | Commit message (Collapse) | Author |
|---|
|
The Bolton FCH needs different firmware files than the Hudson FCH.
A small patch to vendorcode is probably needed to make the XHCI controller work.
XHCI_DEVID in pci_devs.h is probably wrong for Hudson.
Change-Id: Ib81c0881979edcde717217dc89d8af415520d7e5
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/9623
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
1. Use write_pci_int_table to write registers 0xC00/0xC01.
2. Add GPIO, I2C and UART interrupt according
"BKDG for AMD Family 15h Models 60h-6Fh Processors",
50742 Rev 3.01 - July 17, 2015
3. The interrupt valudes are moved from bettong/mptable.c.
All devices work in Windows 10.
Change-Id: Iad13bc02c84a5dfc7c24356436ac560f593304d7
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/11746
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Change-Id: Ie17a744b6ef4e5405b3dfcecc1deb6462220ec60
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/12435
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
On the ASUS KGPE-D16 it was noted that the pin straps did not properly
configure the lane director hardware, causing link training failure
on NIC B. Forcing coreboot to always reconfigure the lane director
on startup resolves this problem.
Change-Id: I5b78cef84960e0f42cc3e0406a7031d12d21f3ad
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12014
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I4202a62217a7aaeaba07e4b994a350e83e064c9c
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12001
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I01481f25189d01b6f4ed778902b2ecc4d39c7912
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12000
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The SB700 silicon is somewhat buggy; if the links come up in an
incorrect state after POR the silicon cannot automatically recover.
If a disk fails to come online, reset the associated link and try
disk detection again.
Change-Id: I29051af5eca5d31b6aecc261e9a48028380eccb3
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11999
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In AHCI mode SeaBIOS randomly fails to detect disks (AHCI timeouts),
with the probability of a failure increasing with the number of disks
connected to the controller. Resetting the SATA controller appears to
show the true state of the underlying hardware, allowing the drive
detection code to attempt link renegotiation as needed.
Change-Id: Ib1f7c5f830a0cdba41cb6f5b05d759adee5ce369
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11998
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
SeaBIOS AHCI drive detection randomly fails for drives present
on the secondary channel of each AHCI SATA BAR. Forcing native
drive detection in AHCI mode resolves this issue.
Change-Id: I34eb1d5d3f2f8aefb749a4eeb911c1373d184938
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11997
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The AMD Register Programming Reference states that the user should
have the option to disable Active Link Power Management for two
reasons. First, some drives may not function correctly with the
ALPM implementation of the SP5100, and second there are some
situations where low latency access is more important than the
power savings created by using ALPM.
Allow the user to disable ALPM if desired.
Change-Id: I88055cbb4df4d7ba811cef7056c0a6ca2612fcb0
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11993
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch adds CC6 power save support to the AMD Family 15h
support code. As CC6 is a complex power saving state that
relies heavily on CPU, northbridge, and southbridge cooperation,
this patch alters significant amounts of code throughout the
tree simultaneously.
Allowing the CPU to enter CC6 allows the second level of turbo
boost to be reached, and also provides significant power savings
when the system is idle due to the complete core shutdown.
Change-Id: I44ce157cda97fb85f3e8f3d7262d4712b5410670
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11979
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ib6d1be64691cf5a1c0b7464284fbae4e583f383e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12402
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I4e0a52eb90910604f8640ad7533b5d71be6c8e20
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11983
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I8ee757d07c82c151b36def6b709163ff144d244f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11984
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I147284e6a435f4b96d6821a122c1f4f9ddc2ea33
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11981
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
EHCI functions have moved.
Change-Id: I47e79d3790b272b0fc322d534de733889679622b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/12264
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
This cast only hides errors in matching the API properly.
Change-Id: Ic396dfb572a50ac5ce5c1c83424e1f17f15bad1d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/12270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The acpi_get_sleep_type function in SB700 ramstage is only needed
for boards / CPUs that require late CBMEM initialization.
Providing this function in early CBMEM-compatible boards breaks
building of the ACPI S3 code due to multiple definitions of
acpi_get_sleep_type.
Change-Id: Ieebc2640a586812e3e2bfd410987205d64147314
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12267
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I2a6cd7ad27cb6d16dfe3267ea6fb844a5e2e20c6
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11083
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I5ea0f9338ccdd658b5fbec72aa35b4f80d63d4f9
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11084
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ib4b643441a5b887abf73cc55930ea9b01037f6ea
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11085
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Bring http://review.coreboot.org/#/c/10582/ to Hudson
Change-Id: I1ba3047699c304a769215fe901dc3511bf23199d
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11022
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a comment explaining what `abcfg_reg(0xc0, 0x01FF, 0x0F4)` does.
This is a follow-up for commit 24501cae (AMD cimx/sb800: Initially
enable all GPP ports).
Change-Id: I5ac263ee088d36a7f7a2d03c1454ed647faa7147
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/12190
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch addresses changes requested to commit 85c39a4c
(southbridge/amd/sb700: Add Suspend to RAM (S3) support)
- remove unused/commented out code
- remove unnecessary guards around acpi_get_sleep_type()
Change-Id: I2878e038d2f9f8d182615e1f4a75ddce5c45d5f3
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/12206
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ic643e31b721f11a90d8fb5f8c8f8a3b7892c0d73
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11949
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I88203907270db1a268bd377151f15c24fca1efdc
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11964
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ieb27bd51dfd45dd15d24a576865d38180a07444e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12175
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
LPC decodes were not enabled, leading to a failure of POST 80 cards
and similar debugging devices. Enable the relevant LPC decodes
to allow debugging.
Additionally, the SMBUS controllers were not properly set up.
Enable both the primary and auxiliary controllers.
Finally, K10 and higher CPUs were hanging during boot due to
a misconfigued IOAPIC. Properly configure the IOAPIC.
Change-Id: I9ffb6542ce445ac971fb81f4f554e7f1313e6a98
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12177
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Idf1db091f1d1e40ce2f248bc25d662cf9608b27e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12179
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I1d7d6715663a13ab94fd6d71808e35f0f7384d00
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11938
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I507c93556dd66c3590c8ca11c06cd5b2dd7884c5
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12176
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: Ia13ba58118a826e830a4dc6e2378b76110fcabad
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11939
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I29ece10eeefc2c75a3829c169f1e1aede7194ec2
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12079
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Certain devices (such as the LSI SAS 2008 controller) do not
respond to PCI probes immediately after link training. If it
is known that such a device is likely to be installed allow the
mainboard to insert an appropriate delay.
Change-Id: Ibcd9426628cacd6f88e6e3fcbc2b3eb7e3a92081
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11991
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
The hudson chipset has 4 USB controllers, the fourth is USB1.1-only and
(presumably) not used very often, add support for hiding it:
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) USB1 (3.0, XHCI)
00:10.1 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03)
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB2 (2.0, OHCI+EHCI)
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB3 (2.0, OHCI+EHCI)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB4 (1.1, OHCI only)
Change-Id: I804e7852fd0a6f870dd118b429473cb06ebac9a4
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7355
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
On my Foxconn nT-A3500 on cold boot the board doesn't survive the soft
reboot in the UsbRxMode path and the vendor bios doesn't touch this
Cg2Pll voltage setting either.
The fixup code for UsbRxMode in src/vendorcode/amd/cimx/sb800/SBPort.c
doesn't seem to "CG PLL multiplier for USB Rx 1.1 mode", but rather
lowers the Cg2Pll voltage from the hw default of 1.222V to 1.1V
by setting Cg2Pll_IVR_TRIM in CGPllConfig5 to 1000.
See also USB_PLL_Voltage which is only used in the UsbRxMode code path.
However if this is already the efuse/eprom default for the SB800 then
UsbRxMode is a no-op, so whether or not it gets executed depends on the
very exact hw revision of the southbridge chip and could change between
two instances of the same board.
UsbRxMode used to be unitialized and was first set to default to 1
in http://review.coreboot.org/6474 (change I32237ff9,
southbridge/amd/cimx/sb800: Uninitialized variables in config func):
> > Why initialize those to 1? (just curious)
> See src/vendorcode/amd/cimx/sb800/SBTYPE.h
> git grep 'SbSpiSpeedSupport\|UsbRxMode'
> src/vendorcode/amd/cimx/sb800/SBTYPE.h
I could not find a corresponding errata in the SB800 errata list,
however errata 15 (USB Resets Asynchronously With Port CF9h Hard Reset)
might play into this being unsafe to do since the code uses CF9h to
reset.
So its possible that while previously undefined it still ended up
defaulting to 0 and the codepath exercised on my board is simply
buggy or there is a difference between a true "SB800" and the
"A50 Hudson M1" presumably used on my board.
Change-Id: I33f45925e222b86c0a97ece48f1ba97f6f878499
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10549
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I7503ae42eb8bc91411413ef2cc7e7a723df7091a
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11990
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
Do not hardcode the CPU downstream non-posted request limit; the
value of this register is CPU family specific and is set appropriately
in the corresponding CPU driver code.
Change-Id: I432b942f114243cba23c9a8d916cf6d07bc4740b
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11935
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Add some missing devices to device tree and header.
Remove the obsolete devices.
Change-Id: Ieeca06c68fe8c8eef6be4fab43193b898aebf013
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/11378
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Instead of reaching into src/include and re-writing code
allow for cleaner code sharing within coreboot and its
utilities. The additional thing needed at this point is
for the utilities to provide a printk() declaration within
a <console/console.h> file. That way code which uses printk()
can than be mapped properly to verbosity of utility parameters.
Change-Id: I9e46a279569733336bc0a018aed96bc924c07cdd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11592
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The location of the AMD ROMSIG binary was being checked and warnings
were being printed even when the ROMSIG file wasn't being used.
These false warnings are avoided by moving the warnings into the
block where the CBFS file for the ROMSIG is generated.
Change-Id: Ie44a2ad97ff3b15df6dc9b8166992de6ed837997
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11161
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
When the user's primary group contains a space ls -l and awk get the
wrong value for the file size. This results in padding the
coreboot_psp_directory_combine_pubkey.bin file too much which ultimately
means RtmPubSigned.key can not be placed at the necessary offset.
Changing from ls -l to ls -ln seemed like the most minimal,
POSIX-friendly way to effect this change.
Change-Id: Icbeaad476753924626adb6de53dc9a30052d91a6
Signed-off-by: Dan Christensen <opello@opello.org>
Reviewed-on: http://review.coreboot.org/11242
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
As acpi_write_hpet() uses CONFIG_HPET_ADDRESS in the HPET table we
need to use CONFIG_HPET_ADDRESS when assigning it to the device.
Change-Id: I656f917658f1c1717bb3653fa048a6d36fca2454
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10925
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Some FSF addresses found their way back into our tree.
Change-Id: I34b465fc78734d818eca1d6962a1e62bf9d6e7f3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/11145
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I944fb254e9470c80b13c9eef9d6b1177a56e615f
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Signed-off-by: Scott Duplichan <scott@notabs.org>
Reviewed-on: http://review.coreboot.org/10582
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
1. Add functions to support fan control.
2. When IMC firmware is added, the current firmwares' layout
cause build error. There is not enough space to add some firmwares,
so HUDSON_PSP_OFFSET is added to fix this problem.
Change-Id: Ie470a88cb9da256d9f72ea56bf268c15df195784
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/10720
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Fix typo. Use the correct math helper int-lt.
Change-Id: Ia5e722020c75595dfcfb853ea8238fb8391f9a04
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10980
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The new attributes increase the header size, breaking this assumption.
Change-Id: Ib23862f27650b39133deafb74a24327b098b6e86
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10942
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change-Id: I08f7251f8fc42b9028b1fdb830546f9922ef43aa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: YongGon Kim <ilios86@gmail.com>
Reviewed-on: http://review.coreboot.org/10914
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
|
