summaryrefslogtreecommitdiff
path: root/src/southbridge
AgeCommit message (Collapse)Author
2018-11-16sb/intel/lynxpoint: Generate the ACPI FADT with a common functionTristan Corrick
The function `acpi_fill_fadt()` is based on that of sb/intel/bd82x6x. Tested on an ASRock H81M-HDS and a Google Peppy board, both using Linux 4.9 with `acpi=strict`. No ACPI errors or warnings appear in the kernel log. System reset, poweroff, and S3 suspend/resume continue to work. General improvements -------------------- - `fadt->preferred_pm_profile` is set based on the value of `CONFIG_SYSTEM_TYPE_LAPTOP` instead of being hardcoded. - Constants are used instead of magic values in more locations. - `fadt->gpe0_blk`, `fadt->gpe0_blk_len`, and `fadt->x_gpe0_blk` are set appropriately depending on whether the system uses Lynx Point LP or not. - Boards can indicate docking support in the FADT via the devicetree. Changes to existing Lynx Point boards ------------------------------------- - `header->asl_compiler_revision` changes from 1 to 0. - `fadt->model` is left at 0 instead of being set to 1. This field is only needed for ACPI 1.0 compatibility. - `fadt->flush_size` and `fadt->flush_stride` are set to 0. This is because their values are ignored, since `ACPI_FADT_WBINVD` is set in `fadt->flags`. - `fadt->duty_offset` is set to 0 instead of 1. None of the existing boards indicate support for changing the processor duty cycle (as `fadt->duty_width` is set to 0), so `fadt->duty_offset` does not currently need to be set. - Access sizes of registers are set. - On mb/intel/baskingridge, the pmbase is now read using the common function `get_pmbase()` instead of `pci_read_config16(...)`. - On mb/intel/baskingridge, the value of `fadt->x_gpe0_blk.bit_width` changes from 64 to 128. The correct value should be 128 (bits), to match `fadt->gpe0_blk_len`, which is set to 16 (bytes). - On Lynx Point LP systems, the unused extended address `fadt->x_gpe0_blk` sets its address space ID to be consistent with other unused extended addresses. Such a change should not alter the interpretation of the registers as being unused. Why not set them all to zero? Simply because the existing practice, in both coreboot and some other vendors' firmware, has them set in such a case. A diff of the FADT from a Google Peppy board is below: --- pre/facp.dsl 2018-10-30 20:14:52.676570798 +1300 +++ post/facp.dsl 2018-10-30 20:15:06.904381436 +1300 @@ -1,179 +1,179 @@ /* * Intel ACPI Component Architecture * AML/ASL+ Disassembler version 20180810 (64-bit version) * Copyright (c) 2000 - 2018 Intel Corporation * - * Disassembly of facp.dat, Tue Oct 30 20:14:52 2018 + * Disassembly of facp.dat, Tue Oct 30 20:15:06 2018 * * ACPI Data Table [FACP] * * Format: [HexOffset DecimalOffset ByteLength] FieldName : FieldValue */ [000h 0000 4] Signature : "FACP" [Fixed ACPI Description Table (FADT)] [004h 0004 4] Table Length : 000000F4 [008h 0008 1] Revision : 04 -[009h 0009 1] Checksum : 61 +[009h 0009 1] Checksum : 6E [00Ah 0010 6] Oem ID : "CORE " [010h 0016 8] Oem Table ID : "COREBOOT" [018h 0024 4] Oem Revision : 00000000 [01Ch 0028 4] Asl Compiler ID : "CORE" -[020h 0032 4] Asl Compiler Revision : 00000001 +[020h 0032 4] Asl Compiler Revision : 00000000 [024h 0036 4] FACS Address : 7BF46240 [028h 0040 4] DSDT Address : 7BF46280 -[02Ch 0044 1] Model : 01 +[02Ch 0044 1] Model : 00 [02Dh 0045 1] PM Profile : 02 [Mobile] [02Eh 0046 2] SCI Interrupt : 0009 [030h 0048 4] SMI Command Port : 000000B2 [034h 0052 1] ACPI Enable Value : E1 [035h 0053 1] ACPI Disable Value : 1E [036h 0054 1] S4BIOS Command : 00 [037h 0055 1] P-State Control : 00 [038h 0056 4] PM1A Event Block Address : 00001000 [03Ch 0060 4] PM1B Event Block Address : 00000000 [040h 0064 4] PM1A Control Block Address : 00001004 [044h 0068 4] PM1B Control Block Address : 00000000 [048h 0072 4] PM2 Control Block Address : 00001050 [04Ch 0076 4] PM Timer Block Address : 00001008 [050h 0080 4] GPE0 Block Address : 00001080 [054h 0084 4] GPE1 Block Address : 00000000 [058h 0088 1] PM1 Event Block Length : 04 [059h 0089 1] PM1 Control Block Length : 02 [05Ah 0090 1] PM2 Control Block Length : 01 [05Bh 0091 1] PM Timer Block Length : 04 [05Ch 0092 1] GPE0 Block Length : 20 [05Dh 0093 1] GPE1 Block Length : 00 [05Eh 0094 1] GPE1 Base Offset : 00 [05Fh 0095 1] _CST Support : 00 [060h 0096 2] C2 Latency : 0001 [062h 0098 2] C3 Latency : 0057 -[064h 0100 2] CPU Cache Size : 0400 -[066h 0102 2] Cache Flush Stride : 0010 -[068h 0104 1] Duty Cycle Offset : 01 +[064h 0100 2] CPU Cache Size : 0000 +[066h 0102 2] Cache Flush Stride : 0000 +[068h 0104 1] Duty Cycle Offset : 00 [069h 0105 1] Duty Cycle Width : 00 [06Ah 0106 1] RTC Day Alarm Index : 0D [06Bh 0107 1] RTC Month Alarm Index : 00 [06Ch 0108 1] RTC Century Index : 00 [06Dh 0109 2] Boot Flags (decoded below) : 0003 Legacy Devices Supported (V2) : 1 8042 Present on ports 60/64 (V2) : 1 VGA Not Present (V4) : 0 MSI Not Supported (V4) : 0 PCIe ASPM Not Supported (V4) : 0 CMOS RTC Not Present (V5) : 0 [06Fh 0111 1] Reserved : 00 [070h 0112 4] Flags (decoded below) : 00008CAD WBINVD instruction is operational (V1) : 1 WBINVD flushes all caches (V1) : 0 All CPUs support C1 (V1) : 1 C2 works on MP system (V1) : 1 Control Method Power Button (V1) : 0 Control Method Sleep Button (V1) : 1 RTC wake not in fixed reg space (V1) : 0 RTC can wake system from S4 (V1) : 1 32-bit PM Timer (V1) : 0 Docking Supported (V1) : 0 Reset Register Supported (V2) : 1 Sealed Case (V3) : 1 Headless - No Video (V3) : 0 Use native instr after SLP_TYPx (V3) : 0 PCIEXP_WAK Bits Supported (V4) : 0 Use Platform Timer (V4) : 1 RTC_STS valid on S4 wake (V4) : 0 Remote Power-on capable (V4) : 0 Use APIC Cluster Model (V4) : 0 Use APIC Physical Destination Mode (V4) : 0 Hardware Reduced (V5) : 0 Low Power S0 Idle (V5) : 0 [074h 0116 12] Reset Register : [Generic Address Structure] [074h 0116 1] Space ID : 01 [SystemIO] [075h 0117 1] Bit Width : 08 [076h 0118 1] Bit Offset : 00 -[077h 0119 1] Encoded Access Width : 00 [Undefined/Legacy] +[077h 0119 1] Encoded Access Width : 01 [Byte Access:8] [078h 0120 8] Address : 0000000000000CF9 [080h 0128 1] Value to cause reset : 06 [081h 0129 2] ARM Flags (decoded below) : 0000 PSCI Compliant : 0 Must use HVC for PSCI : 0 [083h 0131 1] FADT Minor Revision : 00 [084h 0132 8] FACS Address : 000000007BF46240 [08Ch 0140 8] DSDT Address : 000000007BF46280 [094h 0148 12] PM1A Event Block : [Generic Address Structure] [094h 0148 1] Space ID : 01 [SystemIO] [095h 0149 1] Bit Width : 20 [096h 0150 1] Bit Offset : 00 -[097h 0151 1] Encoded Access Width : 00 [Undefined/Legacy] +[097h 0151 1] Encoded Access Width : 02 [Word Access:16] [098h 0152 8] Address : 0000000000001000 [0A0h 0160 12] PM1B Event Block : [Generic Address Structure] [0A0h 0160 1] Space ID : 01 [SystemIO] [0A1h 0161 1] Bit Width : 00 [0A2h 0162 1] Bit Offset : 00 [0A3h 0163 1] Encoded Access Width : 00 [Undefined/Legacy] [0A4h 0164 8] Address : 0000000000000000 [0ACh 0172 12] PM1A Control Block : [Generic Address Structure] [0ACh 0172 1] Space ID : 01 [SystemIO] [0ADh 0173 1] Bit Width : 10 [0AEh 0174 1] Bit Offset : 00 -[0AFh 0175 1] Encoded Access Width : 00 [Undefined/Legacy] +[0AFh 0175 1] Encoded Access Width : 02 [Word Access:16] [0B0h 0176 8] Address : 0000000000001004 [0B8h 0184 12] PM1B Control Block : [Generic Address Structure] [0B8h 0184 1] Space ID : 01 [SystemIO] [0B9h 0185 1] Bit Width : 00 [0BAh 0186 1] Bit Offset : 00 [0BBh 0187 1] Encoded Access Width : 00 [Undefined/Legacy] [0BCh 0188 8] Address : 0000000000000000 [0C4h 0196 12] PM2 Control Block : [Generic Address Structure] [0C4h 0196 1] Space ID : 01 [SystemIO] [0C5h 0197 1] Bit Width : 08 [0C6h 0198 1] Bit Offset : 00 -[0C7h 0199 1] Encoded Access Width : 00 [Undefined/Legacy] +[0C7h 0199 1] Encoded Access Width : 01 [Byte Access:8] [0C8h 0200 8] Address : 0000000000001050 [0D0h 0208 12] PM Timer Block : [Generic Address Structure] [0D0h 0208 1] Space ID : 01 [SystemIO] [0D1h 0209 1] Bit Width : 20 [0D2h 0210 1] Bit Offset : 00 -[0D3h 0211 1] Encoded Access Width : 00 [Undefined/Legacy] +[0D3h 0211 1] Encoded Access Width : 03 [DWord Access:32] [0D4h 0212 8] Address : 0000000000001008 [0DCh 0220 12] GPE0 Block : [Generic Address Structure] -[0DCh 0220 1] Space ID : 00 [SystemMemory] +[0DCh 0220 1] Space ID : 01 [SystemIO] [0DDh 0221 1] Bit Width : 00 [0DEh 0222 1] Bit Offset : 00 [0DFh 0223 1] Encoded Access Width : 00 [Undefined/Legacy] [0E0h 0224 8] Address : 0000000000000000 [0E8h 0232 12] GPE1 Block : [Generic Address Structure] [0E8h 0232 1] Space ID : 01 [SystemIO] [0E9h 0233 1] Bit Width : 00 [0EAh 0234 1] Bit Offset : 00 [0EBh 0235 1] Encoded Access Width : 00 [Undefined/Legacy] [0ECh 0236 8] Address : 0000000000000000 Change-Id: I9638bb5ff998518eb750e3e7e85b51cdaf1f070e Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29387 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-16src: Remove unneeded include <lib.h>Elyes HAOUAS
Change-Id: I801849fb31fe6958e3d9510da50e2e2dd351a98d Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29304 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-11-16src: Remove unneeded include <console/console.h>Elyes HAOUAS
Change-Id: I40f8b4c7cbc55e16929b1f40d18bb5a9c19845da Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29289 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-11-16src: Get rid of duplicated includesElyes HAOUAS
Change-Id: I252a1cd77bf647477edb7dddadb7e527de872439 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29582 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2018-11-16sb/amd/cs5536: Remove unneeded include <cpu/x86/bist.h>Elyes HAOUAS
Change-Id: Ifae9d67bbba57b30ee9a2f31c448efcb27981c57 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29310 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2018-11-16sb/amd: Remove dead assignment in SPI driverPaul Menzel
Value stored to 'cmd' is never read Change-Id: I794b6e12f5af272705cd996f7ca5099e9b9dbfc7 Found-by: scan-build from clang 6 Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/29568 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-11-16sb/amd: Fix grammar in commentPaul Menzel
Change-Id: I478a59534ec997947855eb0ff228a0dd9e15a5a5 Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/29567 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2018-11-12src: Remove unneeded include "{arch,cpu}/cpu.h"Elyes HAOUAS
Change-Id: I17c4fc4e3e2eeef7c720c6a020b37d8f7a0f57a4 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29300 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-11-07sb/intel: Deduplicate vbnv_cmos_failed and rtc_initPatrick Rudolph
* Move all implementations to into common folder. * Add rtc.c for rtc based functions Allows all Intel based platforms to use VBOOT_VBNV_CMOS. Change-Id: Ia494e6d418af6f907c648376674776c54d95ba71 Signed-off-by: Patrick Rudolph <siro@das-labor.org> Reviewed-on: https://review.coreboot.org/29427 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-11-07southbridge/amd/pi/hudson: Get rid of void pointer mathRichard Spiegel
Pointer math with void pointers is illegal in many compilers, though it works with GCC because it assumes size of void to be 1. Change the pointers or add parenthesis to force a proper order that will not cause compile errors if compiled with a different compiler, and more importantly, don't have unsuspected side effects. BUG=b:118484178 TEST=Build AMD Bettong. Change-Id: I4167c7eeb9339937b064e81e615ceb65f4689082 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/29438 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2018-11-07intel: Get rid of smm_get_pmbasePatrick Rudolph
Change-Id: I2b3168c600a81502f9cd1ff3203c492cf026e532 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/27279 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-11-05amd: Fix non-local header treated as localElyes HAOUAS
Change-Id: I0668b73cd3a5bf5220af55c29785220b77eb5259 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29103 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-05sb/intel/lynxpoint: Remove irrelevant conditional statementElyes HAOUAS
After a {break,return}, "else" is generally not needed. Change-Id: I6145424ef8ffe6854c18c1d885f579d37853a70c Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29267 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-01sb/intel/common: Create a common implementation of `acpi_fill_madt()`Tristan Corrick
The function `acpi_fill_madt()` is identical among all the Lynx Point boards and sb/intel/bd82x6x, so share a common function between them. Earlier Intel platforms have similar implementations of this function. The common implementation might only need minor alterations to support them. Tested on an ASRock H81M-HDS and Google Peppy (variant of Slippy). No issues arose from this patch. Change-Id: Ife9e3917febf43d8a92cac66b502e2dee8527556 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29388 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01sb/intel/lynxpoint: Include <stdint.h> to fix compilation errorsTristan Corrick
If the file `southbridge/intel/lynxpoint/nvs.h` is included in a file that does not already include <stdint.h>, compilation errors result. Adding the necessary <stdint.h> inclusions fixes compilation for an ASRock H81M-HDS. Change-Id: Id0d14705282cc959146e00dd47754ee8a2e8e825 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29389 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01sb/intel/lynxpoint: Add a common platform.asl fileTristan Corrick
The platform.asl file is copied from sb/intel/bd82x6x, and also matches the contents deleted from each mainboard's platform.asl. Tested on an ASRock H81M-HDS and a Google Peppy board (variant of Slippy). No issues arose from this patch. Change-Id: I539e401ce9af83070f69147526ca3b1c122f042c Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29386 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01sb/intel/lynxpoint: Provide a function for mainboard super I/O configTristan Corrick
The super I/O setup needs to be done after the LPC is enabled. For Lynx Point, configuring the super I/O in `mainboard_romstage_entry()` is too early to get a serial console output. To remedy this, add a function `mainboard_config_superio()` that will be called at the appropriate time, and can be overridden by mainboard code. Change-Id: Iaf4188a17533c636e7b0c7efa220bc6a25876dda Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29382 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01sb/intel/lynxpoint: Automatically generate the ACPI PCI routing tableTristan Corrick
This patch is based on a8a9f34e9b7b ("sb/intel/i82801{g,j}x: Automatically generate ACPI PIRQ tables") Tested on an ASRock H81M-HDS. The generated _PRT object looks correct, and the system doesn't show any issue when running. The following assignments occur: ACPI_PIRQ_GEN: PCI: 00:02.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:03.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:14.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:16.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:1a.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:1b.0: pin=0 pirq=6 ACPI_PIRQ_GEN: PCI: 00:1c.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:1c.1: pin=1 pirq=1 ACPI_PIRQ_GEN: PCI: 00:1c.2: pin=2 pirq=2 ACPI_PIRQ_GEN: PCI: 00:1c.3: pin=3 pirq=3 ACPI_PIRQ_GEN: PCI: 00:1d.0: pin=0 pirq=7 ACPI_PIRQ_GEN: PCI: 00:1f.2: pin=1 pirq=3 ACPI_PIRQ_GEN: PCI: 00:1f.3: pin=2 pirq=2 Also tested on a Google Peppy board. The following assignments occur: ACPI_PIRQ_GEN: PCI: 00:02.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:03.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:14.0: pin=0 pirq=2 ACPI_PIRQ_GEN: PCI: 00:1b.0: pin=0 pirq=6 ACPI_PIRQ_GEN: PCI: 00:1c.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:1d.0: pin=0 pirq=3 ACPI_PIRQ_GEN: PCI: 00:1f.2: pin=0 pirq=6 ACPI_PIRQ_GEN: PCI: 00:1f.3: pin=1 pirq=2 ACPI_PIRQ_GEN: PCI: 00:1f.6: pin=2 pirq=1 A diff of the _PRT object for the Google Peppy board is below. The code used in the diff has been modified for clarity, but the semantics remain the same. To summarise the diff: * The disabled PCIe root ports are no longer included. * The LPC controller is no longer included, as it has no interrupt pin. The pins for the remaining LPC devices are each one less. Perhaps the original _PRT object was incorrect? * The SDIO device is no longer included, as it is disabled. * The Serial IO devices are no longer included, but that is due to a separate issue I am having with this system (the devices don't show up under Linux regardless of this patch). In short: their omission is not a fault of this patch. --- pre/_PRT +++ post/_PRT @@ -1,301 +1,157 @@ Method (_PRT, 0, NotSerialized) // _PRT: PCI Routing Table { If (PICM) { - Return (Package (0x12) + Return (Package (0x09) { Package (0x04) { 0x0002FFFF, Zero, Zero, 0x10 }, Package (0x04) { 0x0003FFFF, Zero, Zero, 0x10 }, Package (0x04) { 0x0014FFFF, Zero, Zero, 0x12 }, Package (0x04) { 0x001BFFFF, Zero, Zero, 0x16 }, Package (0x04) { 0x001CFFFF, Zero, Zero, 0x10 }, - Package (0x04) - { - 0x001CFFFF, - One, - Zero, - 0x11 - }, - - Package (0x04) - { - 0x001CFFFF, - 0x02, - Zero, - 0x12 - }, - - Package (0x04) - { - 0x001CFFFF, - 0x03, - Zero, - 0x13 - }, - Package (0x04) { 0x001DFFFF, Zero, Zero, 0x13 }, Package (0x04) { 0x001FFFFF, Zero, Zero, 0x16 }, Package (0x04) { 0x001FFFFF, One, Zero, 0x12 }, Package (0x04) { 0x001FFFFF, 0x02, Zero, 0x11 - }, - - Package (0x04) - { - 0x001FFFFF, - 0x03, - Zero, - 0x10 - }, - - Package (0x04) - { - 0x0015FFFF, - Zero, - Zero, - 0x14 - }, - - Package (0x04) - { - 0x0015FFFF, - One, - Zero, - 0x15 - }, - - Package (0x04) - { - 0x0015FFFF, - 0x02, - Zero, - 0x15 - }, - - Package (0x04) - { - 0x0015FFFF, - 0x03, - Zero, - 0x15 - }, - - Package (0x04) - { - 0x0017FFFF, - Zero, - Zero, - 0x17 } }) } Else { - Return (Package (0x12) + Return (Package (0x09) { Package (0x04) { 0x0002FFFF, Zero, ^LPCB.LNKA, Zero }, Package (0x04) { 0x0003FFFF, Zero, ^LPCB.LNKA, Zero }, Package (0x04) { 0x0014FFFF, Zero, ^LPCB.LNKC, Zero }, Package (0x04) { 0x001BFFFF, Zero, ^LPCB.LNKG, Zero }, Package (0x04) { 0x001CFFFF, Zero, ^LPCB.LNKA, Zero }, - Package (0x04) - { - 0x001CFFFF, - One, - ^LPCB.LNKB, - Zero - }, - - Package (0x04) - { - 0x001CFFFF, - 0x02, - ^LPCB.LNKC, - Zero - }, - - Package (0x04) - { - 0x001CFFFF, - 0x03, - ^LPCB.LNKD, - Zero - }, - Package (0x04) { 0x001DFFFF, Zero, ^LPCB.LNKD, Zero }, Package (0x04) { 0x001FFFFF, Zero, ^LPCB.LNKG, Zero }, Package (0x04) { 0x001FFFFF, One, ^LPCB.LNKC, Zero }, Package (0x04) { 0x001FFFFF, 0x02, ^LPCB.LNKB, Zero - }, - - Package (0x04) - { - 0x001FFFFF, - 0x03, - ^LPCB.LNKA, - Zero - }, - - Package (0x04) - { - 0x0015FFFF, - Zero, - ^LPCB.LNKE, - Zero - }, - - Package (0x04) - { - 0x0015FFFF, - One, - ^LPCB.LNKF, - Zero - }, - - Package (0x04) - { - 0x0015FFFF, - 0x02, - ^LPCB.LNKF, - Zero - }, - - Package (0x04) - { - 0x0015FFFF, - 0x03, - ^LPCB.LNKF, - Zero - }, - - Package (0x04) - { - 0x0017FFFF, - Zero, - ^LPCB.LNKH, - Zero } }) } } Change-Id: Id3f067cbf7c7d649fbbf774648d8ff928cb752a4 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29381 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01sb/intel/lynxpoint: Add a PCI ID for an SMBus controllerTristan Corrick
The PCI ID was taken from the output of `lspci` on an ASRock H81M-HDS. Change-Id: Idc222392a0973f9ea62b943d18dd762b48c76d17 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29377 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01sb/intel/lynxpoint: Add PCI IDs for more SKUsTristan Corrick
The PCI IDs were taken from the Intel Lynx Point datasheet [1]. [1] Intel® 8 Series/C220 Series Chipset Family Platform Controller Hub (PCH) Datasheet, revision 003, document number 328904. Change-Id: Ie4a264e9325d185334c3d7f7d2ed3c394ac33059 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29376 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01sb/intel/common/pciehp.h: Add missing license headerElyes HAOUAS
Change-Id: Ia669b25683c138d96be00db90d01cf406db4c2eb Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29404 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-01src: Add missing include <stdint.h>Elyes HAOUAS
Change-Id: Idf10a09745756887a517da4c26db7a90a1bf9543 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29403 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-10-31reset: Finalize move to new APINico Huber
Move soft_reset() to `southbridge/amd/common/` it's only used for amdfam10 now. Drop hard_reset() for good. Change-Id: Ifdc5791160653c5578007f6c1b96015efe2b3e1e Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/29059 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-10-30{cpu,drivers,nb,sb}/amd: Replace {MSR,MTRR} addresses with macrosElyes HAOUAS
Change-Id: I7e8de35dcdad52bb311b34bfa9b272d17ed3186b Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29243 Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-30src: Add missing include <stdint.h>Elyes HAOUAS
Change-Id: I6a9d71e69ed9230b92f0f330875515a5df29fc06 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29312 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-24sb/amd: Use 'unsigned int' to bare use of 'unsigned'Elyes HAOUAS
Change-Id: I05f9ea97ea80ac7a8f34845c59bd66e424ba2991 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/28709 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2018-10-24vboot: fix CONFIG_RESUME_PATH_SAME_AS_BOOT S3 resume logicJoel Kitching
- should not check VBOOT_STARTS_IN_BOOTBLOCK to set context flag - implement vboot_platform_is_resuming on platforms missing it - add ACPI_INTEL_HARDWARE_SLEEP_VALUES to two intel southbridges [ originally https://review.coreboot.org/c/coreboot/+/28750 ] BUG=b:114018226 TEST=compile coreboot Change-Id: I1ef0bcdfd01746198f8140f49698b58065d820b9 Signed-off-by: Joel Kitching <kitching@google.com> Reviewed-on: https://review.coreboot.org/29060 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
2018-10-23src: Remove unneeded whitespaceElyes HAOUAS
Change-Id: I6c77f4289b46646872731ef9c20dc115f0cf876d Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29161 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2018-10-23src: Typo fix (cosmetic)Peter Lemenkov
Change-Id: I81985bd2836bdeb369587f170504a8a048ee496b Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29196 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-22amdfam10: Convert to `board_reset()`Nico Huber
And here comes the mess... This just renames do_hard_reset() to do_board_reset() and keeps current behaviour. As these are never called from chipset or board code but only from common code, it's likely that their implementations are untested and not what we actually want. Also note, that sometimes implementations for rom- and ramstage differ considerably. Change-Id: Icdf55ed1a0e0294933f61749a37da2ced01da61c Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/29058 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-22sb/amd/*/hudson: Use CF9 resetNico Huber
Implement board_reset() as "system reset". Change-Id: I80801ba58b9d849ef5e14185510666bd312106c2 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/29057 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-22sb/amd/cimx/sb[89]00: Use CF9 resetNico Huber
Implement board_reset() as "system reset". Change-Id: I2d277b0845b4e8977b68892c2e5e00d8918e063f Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/29056 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-22intel: Use CF9 reset (part 1)Patrick Rudolph
Add SOUTHBRIDGE_INTEL_COMMON_RESET for all Intel platforms that used to perform a "system reset" in their hard_reset() implementation. Replace all duplicate CF9 reset implementations for these platforms. Change-Id: I8e359b0c4d5a1060edd0940d24c2f78dfed8a590 Signed-off-by: Patrick Rudolph <siro@das-labor.org> Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/28862 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-10-18src/{sb/intel,mb/google/auron}: Don't use device_tElyes HAOUAS
Use of device_t is deprecated. Change-Id: I564319506870f75eab58cce535d4e3535a64a993 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/28642 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-10-18cpu/amd: Use common AMD's MSRElyes HAOUAS
Phase 1. Due to the size of the effort, this CL is broken into several phases. Change-Id: I0236e0960cd1e79558ea50c814e1de2830aa0550 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29065 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
2018-10-18mb/lenovo/*/romstage: Use macros instead of magic numbersPeter Lemenkov
Apparently coreboot still uses magic numbers instead of macros in some Lenovo mainboards. Let's use macros instead. Also removed FDD from l520 romstage (original value, 0x3c0c, means that FDD_LPC_EN was also enabled). Change-Id: I6468e3357f8eed434f8527a852e134380f486d9a Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/28976 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-10-15sb/intel/i82801jx: Use macros for LPC_ENArthur Heymans
Change-Id: I4a9a9366c85206fa460519a26f48b3aada5bc7c3 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/29100 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2018-10-08Move compiler.h to commonlibNico Huber
Its spreading copies got out of sync. And as it is not a standard header but used in commonlib code, it belongs into commonlib. While we are at it, always include it via GCC's `-include` switch. Some Windows and BSD quirk handling went into the util copies. We always guard from redefinitions now to prevent further issues. Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/28927 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-10-08src: Use tabs for indentationElyes HAOUAS
Change-Id: I6b40aaf5af5d114bbb0cd227dfd50b0ee19eebba Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/28934 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-04sb/amd/pi/hudson: Remove #if 1Jonathan Neuschäfer
Change-Id: I4cf69dc3df2afaa8f33864374ea93548ab7ad810 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/28830 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-09-21sb/intel/bd82x6x: Don't use device_tElyes HAOUAS
Use of device_t is deprecated. Change-Id: I4909ebffc978f537bbf6269d9e27dbaca43daa10 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/28657 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
2018-09-20sb/intel/common/firmware: Ensure warning is put lateNico Huber
Change-Id: I400de0a622c2b45ea5ef1f1446f4f489ac397c32 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/28673 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-09-18sb/amd/sr5650/sr5650.h: Get rid of device_tElyes HAOUAS
Use of device_t has been abandoned in ramstage. Change-Id: Ib4dbb607cfd1e02d45efe141b498d6505574d6e6 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/28633 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-09-16sb/intel/i82801dx/Kconfig: remove duplicate SOUTHBRIDGE_INTEL_COMMONStefan Tauner
Change-Id: I968ea205e53543f3af68596d6861e25e808057df Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at> Reviewed-on: https://review.coreboot.org/28508 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2018-09-13src/*/intel: introduce warning when building with no IFDAngel Pons
Add a warning as suggested in patch CB:28233 with the "CONFIG_INTEL_DESCRIPTOR_MODE_REQUIRED" option. Change-Id: I42b6b336bb519f3d18b5a41eb20b380636ff5819 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/28382 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-09-13src/*/intel/: clarify Kconfig options regarding IFDStefan Tauner
HAVE_INTEL_FIRMWARE is used to enable certain options that rely on a valid Inter Flash Descriptor to exist. It does *not* identify platforms or boards that are capable of running in descriptor mode if it's valid. Refine the help text to make this clear. Introduce a new option INTEL_DESCRIPTOR_MODE_CAPABLE that does simply declare that IFD is supported by the platform. Select this value everywhere instead of the HAVE_INTEL_FIRMWARE and default HAVE_INTEL_FIRMWARE to y if INTEL_DESCRIPTOR_MODE_CAPABLE is selected. Move the QEMU Q35 special case (deselection of HAVE_INTEL_FIRMWARE) to the mainboard directory. Change-Id: I4791fce03982bf0443bf0b8e26d9f4f06c6f2060 Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at> Reviewed-on: https://review.coreboot.org/28371 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-09-06chromeos/gnvs: remove function and naming cleanupJoel Kitching
- Remove unused acpi_get_chromeos_acpi_info (see CB:28190) - Make function naming in gnvs.h consistent (start with "chromeos_") BUG=b:112288216 TEST=compile and run on eve Change-Id: I5b0066bc311b0ea995fa30bca1cd9235dc9b7d1b Signed-off-by: Joel Kitching <kitching@google.com> Reviewed-on: https://review.coreboot.org/28406 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-08-27intel: Use common HPET table revision functionMarc Jones
Use get_acpi_table_revision(HPET) to keep all table versions in sync. Change-Id: Idb5e8ccd49ec27f87a290f33c62df3c177645669 Signed-off-by: Marc Jones <marcj303@gmail.com> Reviewed-on: https://review.coreboot.org/28278 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-by: Martin Roth <martinroth@google.com>
2018-08-27update all FADT version 3.0 to use the get tables functionMarc Jones
Most FADT report using ACPIv3 FADT table. Using the get revision function keeps the table versions in sync. Change-Id: Ie554faf1be65c7034dd0836f0029cdc79eae1aed Signed-off-by: Marc Jones <marcj303@gmail.com> Reviewed-on: https://review.coreboot.org/28277 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-by: Martin Roth <martinroth@google.com>
2018-08-23Kconfig, Makefile.inc: Remove all traces of ifdfakeAngel Pons
Since ifdfake has been deprecated in favor of better alternatives, there is no need to support it any further. Remove it from the build system. Change-Id: Id62e95ba72004a1e15453e3eb75f09cb8194feb2 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/28233 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 07:53:13 +0000