summaryrefslogtreecommitdiff
path: root/src/southbridge
AgeCommit message (Collapse)Author
2013-03-19lynxpoint: Add cbfs_load_payload() implementationAaron Durbin
SPI accesses can be slow depending on the setup and the access pattern. The current SPI hardware setup to cache and prefetch. The alternative cbfs_load_payload() function takes advantage of the caching in the CPU because the ROM is cached as write protected as well as the SPI's hardware's caching/prefetching implementation. The CPU will fetch consecutive aligned cachelines which will hit the ROM as cacheline-aligned addresses. Once the payload is mirrored into RAM the segment loading can take place by reading RAM instead of ROM. With the alternative cbfs_load_payload() the boot time on a baskingridge board saves ~100ms. This savings is observed using cbmem.py after performing warm reboots and looking at TS_SELFBOOT_JUMP (99) entries. This is booting with a depthcharge payload whose payload file fits within the SMM_DEFAULT_SIZE (0x10000 bytes). Datapoints with TS_LOAD_PAYLOAD (90) & TS_SELFBOOT_JUMP (99) cbmem entries: Baseline Alt -------- -------- 90:3,859,310 (473) 90:3,863,647 (454) 99:3,989,578 (130,268) 99:3,888,709 (25,062) 90:3,899,450 (477) 90:3,860,926 (463) 99:4,029,459 (130,008) 99:3,890,583 (29,657) 90:3,834,600 (466) 90:3,890,564 (465) 99:3,964,535 (129,934) 99:3,920,213 (29,649) Booted baskingridge many times and observed 100ms reduction in TS_SELFBOOT_JUMP times (time to load payload). Change-Id: I27b2dec59ecd469a4906b4179b39928e9201db81 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2783 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-03-19bd82x6x: Fix compiling with USB debug port supportRonald G. Minnich
At some point, compiles with USB Debug port stopped working. This change makes a trivial reordering in the code and adds two makefile entries to make it build without errors. It also works on stout. Build and boot as normal. Works. Enable CONFIG_USB, connect USB debug hardware to the correct port (on stout, that's the one on the left nearest the back) and watch for output. Change-Id: I7fbb7983a19b0872e2d9e4248db8949e72beaaa0 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Reviewed-on: http://review.coreboot.org/2784 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-18lynxpoint: Move a bit of generic RCBA into early_pchDuncan Laurie
Rather than have to repeat this bit in every mainboard. Also, remove the reset of the RTC power status from here. We had done this in TOT for current platforms but did not carry it back to emeraldlake2 where this branched from. If we clear the status here then we don't get an event logged later which can be important for the devices that do not have a CMOS battery. Change-Id: Ia7131e9d9e7cf86228a285df652a96bcabf05260 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2683 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-18haswell: Use SMM ModulesAaron Durbin
This commit adds support for using the SMM modules for haswell-based boards. The SMI handling was also refactored to put the relocation handler and permanent SMM handler loading in the cpu directory. All tseg adjustment support is dropped by relying on the SMM module support to perform the necessary relocations. Change-Id: I8dd23610772fc4408567d9f4adf339596eac7b1f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2728 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-17Intel HD Audio: clean up initialization codeStefan Reinauer
- Some initialization steps were done twice - One step was missing for Panther Point HDA - Added a 1ms delay after reset - Increased timeout to 1ms for all codec operations Change-Id: Ib751f1a16ccd88ea2fbbb2a10737f76277574026 Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/2518 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-17haswell platforms: restructure romstage mainAaron Durbin
There was a mix of setup code sprinkled across the various components: southbridge code in the northbridge, etc. This commit reorganizes the code so that northbridge code doesn't initialize southbridge components. Additionally, the calling dram initialization no longer calls out to ME code. The main() function in the mainboard calls the necessary ME functions before and after dram initialization. The biggest change is the addition of an early_pch_init() function which initializes the BARs, GPIOs, and RCBA configuration. It is also responsible for reporting back to the caller if the board is being woken up from S3. The one sequence difference is that the RCBA config is performed before claling the reference code. Lastly the rcba configuration was changed to be table driven so that different board/configurations can use the same code. It should be possible to have board/configuration specific gpio and rcba configuration while reusing the romstage code. Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2681 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-17bd82x6x: Add config option to force SATA link to different speeds.Shawn Nematbakhsh
Certain SATA devices claim to support SATA 6 Gbps, but in fact have bugs. For these devices, add a config option to force the SATA link speed to something other than default. Change-Id: I2dc1793cd58771298a392345162d39d20eb0afbb Signed-off-by: Shawn Nematbakhsh <shawnn@google.com> Reviewed-on: http://review.coreboot.org/2765 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-17Pantherpoint: Add XHCI device initDuncan Laurie
This enables power management and clock gating on XHCI. Change-Id: I124ea6c5aca034b7ec4b5286d971c2adfce25c88 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2761 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-17bd82x6x: don't use absolute symbolsAaron Durbin
objcopy -B provides symbols of the form _binary_<name>_(start|end|size). However, the _size variant is an absoult symbol. If one wants to relocate the smi loading the _size symbol will be relocated which is wrong since it is suppose to be a fixed size. There is no way to distinguish symbols that shouldn't be relocated vs ones that can. Instead use the _start and _end variants to determine the size. Change-Id: I55192992cf36f62a9d8dd896e5fb3043a3eacbd3 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2760 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-17Add bd82x6x XHCI(USB3) S3/S4 workaroundMarc Jones
The bd82x6x requires some additional setting on S3/S4 entry. Change-Id: I24489ab94dd7cd5a4a64044f25153f5b01a45b77 Signed-off-by: Marc Jones <marc.jones@se-eng.com> Reviewed-on: http://review.coreboot.org/2759 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-17Add bd82x6x PCH functions to SMMMarc Jones
Add the PCH function to SMM for follow-on SMM patches that require these functions. Change-Id: I7f3a512c5e98446e835b59934d63a99e8af15280 Signed-off-by: Marc Jones <marc.jones@se-eng.com> Reviewed-on: http://review.coreboot.org/2758 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-17lynxpoint: Add support for disabling ULT devicesDuncan Laurie
These enables are hidden behind IOBP for some reason. Boot to linux with SDIO disabled and see that the SDIO driver does not load and crash the system. Change-Id: Icfbfa117e9e57a51d32db7f6366a9d0d790adcf0 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2695 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14lynxpoint: lpc resource reservationsAaron Durbin
This commit updates the Lynx Point resource reservations before the coreboot allocator assigns resources. There is no need to mark anything as subtractive decode because there are no devices/buses linked to the LPC device. The I/O range reservations consists of claiming the first 4KiB of I/O space. The PMBASE, GPIOBASE, and LPC generic I/O decode ranges are checked against the default claimed range. If those ranges overlap or fall outside of the default range then those resources are added. The MMIO range reservations consist of claiming everything from the I/O APIC to 4GiB. The RCBA and the LPC Generic Memory range register are then conditionally added if they fall outside of the default MMIO range. Change-Id: I0f560a03814a2b15961fdbe61e4164cd54cff7a5 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2682 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14haswell: more ULT/LP support and minor tweaksDuncan Laurie
- Add ME device ID for Lynxpoint LP - Add GPU device IDs for ULT - SATA init tweaks from checking against DXE reference code - Remove the ICH7 from the SPI driver so it works on all lynxpoint without having to add more LPC device ID checks - Add function disable for audio dsp and xhci, remove PCI bridge - Add interrupt route registers for new devices (needs romstage setup) Change-Id: Idb48f50d0bacb6bf90531c3834542b9abb54fb8a Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2680 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14lynxpoint: Update device IDs and clock gating setupDuncan Laurie
- Add device IDs for lynxpoint mobile and LP variants. - Update the clock gating setup based on BWG - Update the SATA programming based on BWG - Add a DEVSLP0 mux config register Change-Id: Icf4d7bab7f3df7adef5eb7c5e310a6995227a0e5 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2649 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-14lynxpoint: Add new GPIO interface for Lynxpoint-LPDuncan Laurie
The low power variant of the chipset introduces a completely new interface to the GPIOs. This is a 1KB region and so needs to be moved as well so it does not conflict with other IO regions. Also expose the gpio_get functions to ramstage and move the prototypes to pch.h so they can be used for both GPIO interfaces. Change-Id: I20bc18669525af16de8cdf99f0ccfa9612be63ad Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2648 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-14lynxpoint: Add Kconfig entry for Low Power chipsetDuncan Laurie
There are enough subtle differences that it is useful to have a Kconfig entry to differentiate the ULT/LP chipet from the desktop/mobile versions. Change-Id: I04ca1bc6f90bcf9e6994ea7125c98347e8def898 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2645 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-14lynxpoint: ME to BIOS Payload UpdatesAaron Durbin
This commit contains a bevy of updates: - PCI device id is updated to match Lynx Point EDS in the ME driver. - Allocate the memory to store the consumption of the MBP. - me_bios_payload structure is now a structure of pointers that point into the allocated memory. - The ICC profile structure was updated to correctly reflect the documentation. Verfied that output of MBP reading can handle unknown items. Change-Id: I43cc45e6b797444c105e7c842eb5684e9c104687 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2641 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14lynx point: add new ME status informationAaron Durbin
According to the 0.8.0 ME BWG this is a new state. It's not very clear what exactly it entails, but the Basking Ridge CRB was tripping it when MRC_DEBUG was enabled (presumably because of a DID timeout). Instead of 0x17 one can now see the proper message for this state. Change-Id: I5bda1de7d3d957d38a4760a02dcd170ec48782e9 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2640 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14haswell: remove GPIO60 memory reset gate on S3 transitionDuncan Laurie
This is no longer tied to a GPIO but has a proper chipset pin. Change-Id: Iba70338e8c67e3c3c1cb32e69bfea1282fda8cb5 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2643 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14haswell: remove explicit pcie config accessesAaron Durbin
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove the pcie explicit accesses. The default config accesses use MMIO. Change-Id: I8406cec16c1ee1bc205b657a0c90beb2252df061 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2618 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14lynxpoint: PMIR register renameAaron Durbin
The register that controls global reset is named the Power Mangement Initialization Regiser (PMIR). Update the defines to reflect the documentation. Additionally, there is no core well reset control according to the EDS. There is, however, a CF9 lock field to lock this register down. Change-Id: I773c33bec63a06cdb869eb9f94553d476e492798 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2619 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14lynxpoint: Management Engine UpdatesAaron Durbin
The ME9 requirements have added some registers and changed some of the MBP state machine. Implement the changes found so far in the ME9 BWG. There were a couple of reigster renames, but the majority of th churn in the me.h header file is just introducing the data structures in the same order as the ME9 BWG. Change-Id: I51b0bb6620eff4979674ea99992ddab65a8abc18 Signed-Off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2620 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14haswell: add PCI id supportAaron Durbin
In order for coreboot to assign resources properly the pci drivers need to have th proper device ids. Add the host controller and the LPC device ids for Lynx Point. Resource assignment works correctly now w/o odd behavior because of conflicts. Change-Id: Id33b3676616fb0c428d84e5fe5c6b8a7cc5fbb62 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2638 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-14lynxpoint: Update IOBP programming methodDuncan Laurie
This follows the new method outlined in the LPT BWG. It is also very pedantic about its operation so it is easier to read and compare against the docs and the reference code implementation. Change-Id: I235d634cded0c75ec0e9f53488f5b366107a18fa Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/2694 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-14haswell: Add initial support for Haswell platformsAaron Durbin
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore, the southbridge support is included as well. The basis for this code is the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires more attention, but this is a good starting point. This code partially gets up through the romstage just before training memory on a Haswell reference board. Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2616 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-03-12AMD CIMx SB800: Enable AHCI mode for SATA controller by defaultPaul Menzel
The current default is IDE mode which is slower compared to AHCI mode. Therefore use AHCI mode by default. A similar change was made for AMD Persimmon in commit »Enable SATA AHCI for faster boot with SeaBIOS.« (96be74c7) [1] but was indirectly reverted by »sb800: Add sata ahci/raid mode kconfig option« (d4a0e7d0) [2]. [1] http://review.coreboot.org/220 [2] http://review.coreboot.org/225 Change-Id: I4fa31b0a3280891e7a3f37675ae8415205818947 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2661 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-03-09Add Intel Panther Point USB3 initializationMarc Jones
Add PEI updates and ACPI updates for supporting EHCI to XHCI USB port support. Change-Id: I9ace68a1b3950771aefb96c1319b8899291edd9a Signed-off-by: Marc Jones <marc.jones@se-eng.com> Reviewed-on: http://review.coreboot.org/2519 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-06AMD SB800: don't switch clock from 14 to 48 MHz for smscsuperioJens Rottmann
The power up default for the 14M_25M_48M_OSC switchable clock output ball of the SB800 chipset is 14 MHz. sb800/bootblock.c changes this to 48 MHz, which is the correct value for almost all SIOs. However, not for 'smscsuperio' (SMSC SCH311x), which needs the original 14 MHz and is not configurable for other clock speeds. A wrong SIO clock supply results in funny RS232 output (wrong bit speed) and non-working PS/2. We could switch back to 14 MHz in the mainboard's romstage.c, but then the clock frequency would change twice. The resulting short 48 MHz burst causes a handful of rubbish characters on RS232 on every boot until the SIO clock has stabilized again. This patch skips the SB800 clock switch if the SIO Kconfig requests 14 MHz. This does not affect any boards currently in the repository (yet). Change-Id: Icff41fd88dc41c08f3700ab4f786852f04eff2a4 Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de> Reviewed-on: http://review.coreboot.org/2454 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-03-01GPLv2 notice: Unify all files to just use one space in »MA 02110-1301«Paul Menzel
In the file `COPYING` in the coreboot repository and upstream [1] just one space is used. The following command was used to convert all files. $ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/' [1] http://www.gnu.org/licenses/gpl-2.0.txt Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2490 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
2013-02-28Use defines for some i82801ex/gx registersKyösti Mälkki
Change-Id: I0069ec26278b82d61ce5bcfb94d77647dfd3254b Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/2530 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-02-27smm: Update rev 0x30101 SMM revision save stateAaron Durbin
According to both Haswell and the SandyBridge/Ivybridge BWGs the save state area actually starts at 0x7c00 offset from 0x8000. Update the em64t101_smm_state_save_area_t structure and introduce a define for the offset. Note: I have no idea what eptp is. It's just listed in the haswell BWG. The offsets should not be changed. Change-Id: I38d1d1469e30628a83f10b188ab2fe53d5a50e5a Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/2515 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-02-26Unify setting 82801a/b/c/d IOAPIC IDKyösti Mälkki
Remove obscure local copy of writing the ioapic registers. Change-Id: I133e710639ff57c6a0ac925e30efce2ebc43b856 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/2532 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-02-25AMD Southbridge: Add RTC init to lpc_initMike Loptien
Adding RTC init code to the Southbridge initialization code in 'lpc_init'. This initializes the RTC so that the Date Alarm register is set to a valid value (0x00) at startup. By setting the Date Alarm register to 0x00, it does not get evaluated along with the seconds, minutes, and hours when running 'fwts s3'. Information about fwts (Firmware Test Suite) can be found here: https://wiki.ubuntu.com/Kernel/Reference/fwts This is the same edit made to the CIMX SB800 titled 'AMD/Persimmon: Add RTC init to CIMX SB800' with commit ID: c4d3d which can be viewed here: http://review.coreboot.org/#/c/2488/ Change-Id: Iddb7a3cbabe736b511cde03d7dc0a4a0b1c7fd90 Signed-off-by: Mike Loptien <mike.loptien@se-eng.com> Reviewed-on: http://review.coreboot.org/2510 Reviewed-by: Martin Roth <martin.roth@se-eng.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins) Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
2013-02-23AMD/Persimmon: Add RTC init to CIMX SB800Mike Loptien
Adding RTC init code to the Southbridge initialization code in 'late.c'. This initializes the RTC so that the Date Alarm register is set to a valid value (0x00) at startup. By setting the Date Alarm register to 0x00, it does not get evaluated along with the seconds, minutes, and hours when running 'fwts s3'. Information about fwts (Firmware Test Suite) can be found here: https://wiki.ubuntu.com/Kernel/Reference/fwts This was tested on a Persimmon but will apply to other mainboards as well. Change-Id: I9a11bc3f9e3f53c46e7a4d72e62ebb0a4ba1bfe4 Signed-off-by: Mike Loptien <mike.loptien@se-eng.com> Reviewed-on: http://review.coreboot.org/2488 Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-02-21AMD S3: Introduce Kconfig variable 'S3_DATA_SIZE'Zheng Bao
Currently the size of the volatile storage for S3 reserved in the image is hardcoded to 32768 bytes. Make that configurable by introducing the Kconfig 'S3_DATA_SIZE'. As the storage space is needed for storing non-volatile, volatile and MTRR data, add a check if the size is big enough. Change-Id: I9152797cf0045c8da48109a9d760e417717686db Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/2383 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-02-20Whitespace: Replace tab character in license text with two spacesPaul Menzel
For whatever reason tabs got inserted in the license header text. Remove one occurrence of that with the following command [1]. $ git grep -l 'MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.'$'\t' | xargs sed -i 's,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.[ ]*,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.\ \ ,' [1] http://sed.sourceforge.net/grabbag/tutorials/sedfaq.txt Change-Id: Iaf4ed32c32600c3b23c08f8754815b959b304882 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2460 Tested-by: build bot (Jenkins) Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de> Reviewed-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>
2013-02-19build system: Retire REQUIRES_BLOBPatrick Georgi
REQUIRES_BLOB assumes that all blob files come from the 3rdparty directory, builds failed when all files were configured to point to other sources. This change modifies the blob mechanism so that cbfs-files can be tagged as "required" with some specification what is missing. If the configured files can't be found (wrong path, missing file), the build system returns a list of descriptions, then aborts. Change-Id: Icc128e3afcee8acf49bff9409b93af7769db3517 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/2418 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marcj303@gmail.com>
2013-02-19AMD S3: Change S3_VOLATILE_POS to S3_DATA_POSZheng Bao
S3_DATA_POS defines address where the whole S3 data is stored. Change-Id: I4155a0821e74a3653caaead890e5fec5677637aa Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/2438 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-by: Marc Jones <marcj303@gmail.com>
2013-02-18AMD S3: Fix typo vol*a*tile in southbridge KconfigZheng Bao
Change non-volitile to non-volatile. Change-Id: Idfc7db3b3dcf078f0f3134fc62679bed439a4fd2 Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/2437 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
2013-02-14sconfig: rename lapic_cluster -> cpu_clusterStefan Reinauer
The name lapic_cluster is a bit misleading, since the construct is not local APIC specific by concept. As implementations and hardware change, be more generic about our naming. This will allow us to support non-x86 systems without adding new keywords. Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1 Signed-off-by: Stefan Reinauer <reinauer@google.com> Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/2377 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-02-14sconfig: rename pci_domain -> domainStefan Reinauer
The name pci_domain was a bit misleading, since the construct is only PCI specific in a particular (northbridge/cpu) implementation, but not by concept. As implementations and hardware change, be more generic about our naming. This will allow us to support non-PCI systems without adding new keywords. Change-Id: Ide885a1d5e15d37560c79b936a39252150560e85 Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/2376 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-02-11spi.h: Rename the spi.h to spi-generic.hZheng Bao
Since there are and will be other files in nb/sb folders, we change the general spi.h to a file name which is not easy to be duplicated. Change-Id: I6548a81206caa608369be044747bde31e2b08d1a Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: zbao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/2309 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-01-22Hudson: Legacy free question is hudson onlyMartin Roth
The "system is legacy free" question accidentally escaped from the hudson Kconfig where it was intended to stay and went coreboot-wide. This puts it back inside the boundries of the hudson southbridge where it belongs. I also commented the endif statements to make it easier to tell where things belong. Change-Id: I49f7a5eadb96d40c6101a93bc390e644617a5654 Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/2179 Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-01-21Hudson: Cleanup - change SB800 references to hudsonMartin Roth
Go through southbridge/amd/agesa/hudson, thatcher and parmer mainboard directories and change all references to sb800 to reference hudson instead. This is just cleanup and should make no functional difference. Change-Id: Icd6a9a08c4bbf5e1aed394362d24c05811ed1fba Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/2177 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com> Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
2013-01-21Hudson: Changes to support agesa/hudson for legacy freeMartin Roth
Add Kconfig option for Legacy free and hook it into the parmer AGESA initialization as well as the FADT code. This should really be done inside the southbridge wrapper and not in the mainboard, but for now the code to attach it to is inside the mainboard. Update Kconfig for parmer and thatcher to default to legacy free. Change-Id: Ib899bd02ddc5506caae4aca2c589cc2526638cb8 Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/2157 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2013-01-21Hudson: Changes to agesa/hudson FADT for ACPI 3.0Martin Roth
Update the southbridge/amd/agesa/hudson FADT generation for ACPI 3.0 compliance similar to what was done for cimx/SB800/fadt.c in commit 9aa4389. commit 9aa43892e6899b719fe7f4754901a0eae379a934 Author: Martin Roth <martin@se-eng.com> Date: Fri May 25 12:23:32 2012 -0600 Update SB800 CIMX FADT According to the datasheet, PMA_CNT_BLK is no longer available and PM2_CNT_BLK should not be used. Setup for these has been removed from the table and .h file. Change-Id: Ied8eb1f26b4aa364d051ec5f7ed6f482bb440957 Signed-off-by: Martin Roth <martin@se-eng.com> Reviewed-on: http://review.coreboot.org/2140 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2013-01-09Fix typo in SB800 Kconfig for IMC positionMartin Roth
The cimx/sb800 IMC Firmware location Kconfig option has a typo which would could set it to the wrong location. Change-Id: I38016bebd1bfe6ad6d3f1c02cb1960712fbf4ab2 Signed-off-by: Martin Roth <martin@se-eng.com> Reviewed-on: http://review.coreboot.org/2120 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-12-30rs780: Implement `rs780_internal_gfx_disable` and add .disable pcie_opsDenis 'GNUtoo' Carikli
That code will be used to disable the internal GFX card and enable the external PCIe card. The following lines from function `rs780_internal_gfx_enable()` are taken and reversed. /* Disable external GFX and enable internal GFX. */ l_dword = pci_read_config32(nb_dev, 0x8c); l_dword &= ~(1<<0); l_dword |= 1<<1; pci_write_config32(nb_dev, 0x8c, l_dword); It has been tested on the M4A785T-M with the following card inside the PCIe 16x slot: 02:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 210] (rev a2) Change-Id: I7bd412b987fde98c97464175e2c7a384a8f0fb84 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/2065 Tested-by: build bot (Jenkins)
2012-12-29Add AMD Hudson blobs by CONFIG_REQUIRES_BLOBS dependencyMarc Jones
If a 3rd party blob option is selected, make sure that it makes the user select CONFIG_USE_BLOBS as otherwise the build will fail. Signed-off-by: Marc Jones <marc.jones@se-eng.com> Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Change-Id: I04429f23137946525c8577dd9c979bd4a0d17cdc Reviewed-on: http://review.coreboot.org/2080 Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>