| Age | Commit message (Collapse) | Author |
|---|
|
Commit »haswell: Add initial support for Haswell platforms« (76c3700f)
[1] used `1 << 25` to set the I/O APIC ID of 2. Instead using
`2 << 24`, which is the same value, makes it clear, that the
I/O APIC ID is 2.
Commit »Intel Panther Point PCH: Use 2 << 24 to clarify that APIC ID
is 2« (8c937c7e) [2] is used as a template.
[1] http://review.coreboot.org/2616
[2] http://review.coreboot.org/3100
Change-Id: I28f9e90856157b4fdd9a1e781472cc4f51d25ece
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3123
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
The "gigabit ethernet controller" (GEC) block was added to AMD
Hudson A55E to integrate ethernet capabilities into an AMD
southbridge.
The GEC is designed to work with B50610 and B50610M gigabit PHY
chips from Broadcom. These parts may not be generally available
in small quantities for embedded development.
The GEC block requires an opaque firmware blob to function. The
GEC blob is controlled by AMD and Broadcom and is not available
from coreboot.org.
This change removes GEC support from AMD Parmer and AMD Thatcher
mainboards since these boards do not have the Broadcom PHY.
AMD has requested that the GEC be hidden for Hudson FCH since
the PHY parts are not generally available. This Kconfig option
can make it appear that this is a viable and supported way to
add Ethernet to an embedded board. It is possible to use the
Hudson GEC block with other PHYs, but this requires development
of a custom GEC blob and a custom Ethernet driver. A custom GEC
blob has been developed for a Micrel PHY, but there is no
accompanying driver.
Change-Id: I7a7bf4d41e453390ecf987c9c45ef2434fc1f1a3
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3127
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Commit »Support for the Intel ICH7 southbridge.« (debb11fc) [1] used
`1 << 25` to set the I/O APIC ID of 2. Instead using `2 << 24`, which
is the same value, makes it clear, that the I/O APIC ID is 2.
Commit »Intel Panther Point PCH: Use 2 << 24 to clarify that APIC ID
is 2« (8c937c7e) [2] is used as a template.
[1] http://review.coreboot.org/gitweb?p=coreboot.git;a=commit;h=debb11fc1fe5f5560015ab9905f1ccc2e08c73e0
[2] http://review.coreboot.org/3100
Change-Id: Ib688500944cd78a1cc1c8082bb138fa9468bdbfb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3122
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Commit 23023a5 correctly enabled the SB800 GPP PCIe ports but didn't
distribute the 4 GPP PCIe lanes amongst the enabled PCIe ports.
This fix was verified by openvoid on a AsRock E350M1 motherboard.
Change-Id: I0116c5f518e0d000be609013446e53da4112f586
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3104
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Commit »Add support for Intel Panther Point PCH« (8e073829) [1] used
`1 << 25` to set the APIC ID of 2. Using `2 << 24`, which is the same
value, instead makes it clear, that the APIC ID is 2.
[1] http://review.coreboot.org/853
Change-Id: I5044dc470120cde2d2cdfc6e9ead17ddb47b6453
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3100
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Fixing warnings introduced by the following patches:
http://review.coreboot.org/#/c/2684/
http://review.coreboot.org/#/c/2739/
http://review.coreboot.org/#/c/2714/
These patches were meant to fix the dmesg warning about
the OSC method not granting control appropriately. These
patches then introduced warnings during the coreboot build
process which were missed during the patch submission
process. These warnings are below:
Intel ACPI Component Architecture
ASL Optimizing Compiler version 20100528 [Oct 15 2010]
Copyright (c) 2000 - 2010 Intel Corporation
Supports ACPI Specification Revision 4.0a
dsdt.ramstage.asl 1143: Method(_OSC,4)
Warning 1088 - ^ Not all control paths return a value (_OSC)
dsdt.ramstage.asl 1143: Method(_OSC,4)
Warning 1081 - ^ Reserved method must return a value (Buffer required for _OSC)
ASL Input: dsdt.ramstage.asl - 1724 lines, 34917 bytes, 889 keywords
AML Output: dsdt.ramstage.aml - 10470 bytes, 409 named objects, 480 executable opcodes
Compilation complete. 0 Errors, 2 Warnings, 0 Remarks, 494 Optimizations
This patch gives the following compilation status:
Intel ACPI Component Architecture
ASL Optimizing Compiler version 20100528 [Oct 1 2012]
Copyright (c) 2000 - 2010 Intel Corporation
Supports ACPI Specification Revision 4.0a
ASL Input: dsdt.ramstage.asl - 1732 lines, 33295 bytes, 941 keywords
AML Output: dsdt.ramstage.aml - 10152 bytes, 406 named objects, 535 executable opcodes
Compilation complete. 0 Errors, 0 Warnings, 0 Remarks, 432 Optimizations
The fix is simply adding an Else statement to the If which checks
for the proper UUID. This way, all outcomes will return a full
control package. This patch has no effect on the dmesg output.
Change-Id: I8fa246400310b26679ffa3aa278069d2e9507160
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3052
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Reading the paste of code in a message to the mailing list [1],
a typo was spotted and found in one more place.
$ git grep egnoring
src/southbridge/amd/rs780/cmn.c: * egnoring the reversal case
src/southbridge/amd/sr5650/sr5650.c: * egnoring the reversal case
These typos are there since when the code was committed and are
now corrected.
[1] http://www.coreboot.org/pipermail/coreboot/2013-April/075644.html
Change-Id: I55c65f71e4834f209b60d678f0d44bc2f4217099
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3062
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Split the Persimmon DSDT into common code areas.
For example, split the Southbridge specific code into
the Southbridge directory and CPU specific code into
the CPU directory. Also adding the superio.asl file
to the Persimmon DSDT tree. This file is empty for
the moment but will be necessary in the future. I have
also emptied the thermal.asl file in the mainboard
directory because it does not seem to perform as
intended (fan control does not change when it is
brought back into the code base) and it has been
inside a '#if 0' statement for a long time. Removing
it until it is decided that it is actually necessary.
This change was verified in three different ways:
1. Visual comparison of the compiled DSDT pulled from the
Persimmon after booting into Linux using the ACPI tools
acpidump, acpixtract, and iasl. The comparison was done
between the DSDT before and after doing the split work.
This test is somewhat difficult considering the expanse
of the changes. Blocks of code have been moved, and
others changed.
2. Linux logs were dumped before and after the DSDT split.
Logs dumped and compared include dmesg and lspci -tv.
Neither log changed significantly between the two compare
points.
3. The test suite FWTS was run on the Coreboot build both
before and after doing the DSDT split with the command
'sudo fwts -b -P -u'. The flag -b specifies all batch jobs,
-P specifies all power tests, and -u specifies utilities.
Interactive jobs were not run as most of them consist of
laptop checks. Again, there were no significant changes
between the two endpoints.
These tests lead me to believe that there was no change in
the functionality of the ACPI tables apart from what is
known and expected.
This patch is the first of a series of patches to split the DSDT.
The ASRock patch was merged before this one and breaks the ASROCK
E350M1 build (patch 8d80a3fb: http://review.coreboot.org/#/c/3050/).
Please be aware of this dependency when pulling these patches.
Other patches that depend on this patch are
'AMD Fam14: Split out the AMD Fam14 DSDT'
(http://review.coreboot.org/#/c/3051/)
and 'Fam14 DSDT: Also return for unrecognized UUID in _OSC'
(http://review.coreboot.org/#/c/3052/)
Change-Id: I53ff59909cceb30a08e8eab3d59b30b97c802726
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3048
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
src/southbridge/intel/lynxpoint/pmutil.c was committed with two
things that needed fixing.
Change-Id: Ib83343a75840aa29847b607b0275971eb8140f12
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3003
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
The ACPI NVS region was setup in place and there was a CBMEM
table that pointed to it. In order to be able to use NVS
earlier the CBMEM region is allocated for NVS itself during
the LPC device init and the ACPI tables point to it in CBMEM.
The current cbmem region is renamed to ACPI_GNVS_PTR to
indicate that it is really a pointer to the GNVS and does
not actually contain the GNVS.
Change-Id: I31ace432411c7f825d86ca75c63dd79cd658e891
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2970
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds configuration of SerialIO devices in the Lynxpoint-LP
chipset. This includes DMA, I2C, SPI, UART, and SDIO controllers.
There is assorted magic setup necessary for the devices and
while it is similar for each device there are subtle differences
in some register settings.
These devices must be put into "ACPI Mode" in order to take
advantage of S0ix. When in ACPI mode the allocated PCI BARs
must be passed to ACPI so it can be relayed to the OS. When
the devices are in ACPI mode BAR0+BAR1 is saved into ACPI NVS
and then updated and returned when the OS calls _CRS.
Note that is is not entirely complete yet. We need to update
the IASL compiler in our build environment to support ACPI 5.0
in order to be able to pass the FixedDMA entries to the kernel.
There are also no ACPI methods defined yet to do D0->D3->D0
transitions for actually entering/exiting S0ix states.
This is hard to test right now because our kernel does not support
any of these devices in ACPI mode. I was able to build and test
the upstream bleeding-edge branch of the linux-pm git tree. With
that tree I was able to enumerate and load the driver for the
DesignWare I2C driver and attempt to probe the I2C bus -- although
there are no devices attatched.
I am also able to see the resources from ACPI in /proc/iomem get
reserved properly in the kernel.
Change-Id: Ie311addd6a25f3b7edf3388fe68c1cd691a0a500
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2971
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This bit offset is incorrect and should only be set based
on another bit in a different register.
Change-Id: I6037534236e3a4a5d15e15011ed9b5040b435eaf
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2973
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The new enable_pm1() function was doing 2 things wrong:
1. It was doing a RMW of the pm1 register. This means we were
keeping around the enables from the OS during S3 resume. This
is bad in the face of the RTC alarm waking us up because it would
cause an infinite stream of SMIs.
2. The register size of PM1_EN is 16-bits. However, the previous
implementation was accessing it as a 32-bit register.
The PM1 enables should only be set to what we expect to handle in the
firmware before the OS changes to ACPI mode.
Change-Id: Ib1d3caf6c84a1670d9456ed159420c6cb64f555e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2978
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Previously southbridge_smm_init() was provided that did both
the clearing of the SMM state and enabling SMIs. This is
troublesome in how haswell machines bring up the APs. The BSP
enters SMM once to determine if parallel SMM relocation is possible.
If it is possible the BSP releases the APs to do SMM relocation.
Normally, after the APs complete the SMM relocation, the BSP would then
re-enter the relocation handler to relocate its own SMM space.
However, because SMIs were previously enabled it is possible for an SMI
event to occur before the APs are complete or have entered the
relocation handler. This is bad because the BSP will turn off parallel
SMM save state. Additionally, this is a problem because the relocation
handler is not written to handle regular SMIs which can cause an
SMI storm which effectively looks like a hung machine. Correct these
issues by turning on SMIs after all the SMM relocation has occurred.
Change-Id: Id4f07553b110b9664d51d2e670a14e6617591500
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2977
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
When calculating the offsets of the various binary blobs within the
coreboot.rom file, we noticed that using mawk as the awk tool instead
of using gawk led to build issues. This was finally traced to the
maximum value of the unsigned long variables within mawk - 0x7fff_ffff.
Because we were doing calculations on values up in the 0xffxxxxxx
range, these numbers would either be turned into floating point values
and printed using scientific notation, or truncated at 0x7fff_ffff.
To fix this, we print the values out as floating point, with no decimal
digits. This works in gawk, mawk, and original-awk and as the testing
below show, seems to be the best way to do this.
printf %u 0xFFFFFFFF | awk '{printf("%.0f %u %d", $1 , $1 , $1 )}'
mawk: 4294967295 2147483647 2147483647
original-awk: 4294967295 2147483648 4294967295
gawk: 4294967295 4294967295 4294967295
The issue of %d not matching gawk and original-awk has been reported
to ubuntu.
In the future, I'd recommend that whenever awk is used, a format is
specified. It doesn't seem that we can count on the representation
being the same between the different versions.
Change-Id: I7b6b821c8ab13ad11f72e674ac726a98e8678710
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2628
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This reclaims space in ACPI NVS by removing unused fields and
adds new fields for SerialIO BARs which will be used to communicate
the allocated resources to ACPI.
Change-Id: I002bf396cf7b495bc5b7e54b741527e507aff716
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2969
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In the following commit
commit ee5c111755ac4acc6dfb6e10a4e271211e149a39
Author: Paul Menzel <paulepanter@users.sourceforge.net>
Date: Tue Mar 12 12:41:40 2013 +0100
AMD CIMx SB800: Enable AHCI mode for SATA controller by default
Reviewed-on: http://review.coreboot.org/2661
I forgot to update the help texts to the new SATA mode default. Do
so now.
Additionally note that help texts for `choice` do not seem to be
shown.
Change-Id: I17f401633a2136efca2b21a621482e0724ff9f04
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2936
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Make it more similar to i82801d LPC init.
Change-Id: I7b32747ee8012c220c8628994d749999c144b716
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2545
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The haswell patches that verified correctly were not yet submitted,
but verified correctly. However they still used romcc_io.h which was
dropped in another patch earlier today.
With a lot of development happening in parallel, this is
unfortunately nothing that the gerrit 2.6 Rebase If Necessary submit
type could have fixed.
Change-Id: Ifef9ae05b22c408e78d6cff37defd68e4ed91ed9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2876
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
This patch implements support for vboot firmware selection. The vboot
support is comprised of the following pieces:
1. vboot_loader.c - this file contains the entry point,
vboot_verify_firmware(), for romstage to call in order to perform
vboot selection. The loader sets up all the data for the wrapper
to use.
2. vboot_wrapper.c - this file contains the implementation calling the vboot
API. It calls VbInit() and VbSelectFirmware() with the data supplied
by the loader.
The vboot wrapper is compiled and linked as an rmodule and placed in
cbfs as 'fallback/vboot'. It's loaded into memory and relocated just
like the way ramstage would be. After being loaded the loader calls into
wrapper. When the wrapper sees that a given piece of firmware has been
selected it parses firmware component information for a predetermined
number of components.
Vboot result information is passed to downstream users by way of the
vboot_handoff structure. This structure lives in cbmem and contains
the shared data, selected firmware, VbInitParams, and parsed firwmare
components.
During ramstage there are only 2 changes:
1. Copy the shared vboot data from vboot_handoff to the chromeos acpi
table.
2. If a firmware selection was made in romstage the boot loader
component is used for the payload.
Noteable Information:
- no vboot path for S3.
- assumes that all RW firmware contains a book keeping header for the
components that comprise the signed firmware area.
- As sanity check there is a limit to the number of firmware components
contained in a signed firmware area. That's so that an errant value
doesn't cause the size calculation to erroneously read memory it
shouldn't.
- RO normal path isn't supported. It's assumed that firmware will always
load the verified RW on all boots but recovery.
- If vboot requests memory to be cleared it is assumed that the boot
loader will take care of that by looking at the out flags in
VbInitParams.
Built and booted. Noted firmware select worked on an image with
RW firmware support. Also checked that recovery mode worked as well
by choosing the RO path.
Change-Id: I45de725c44ee5b766f866692a20881c42ee11fa8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2854
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This configures power management registers according to
the 1.2.0 reference code drop. There are many inconsistencies
with the documentation and I tried to note those with ?.
This does not do the same for LynxPoint-H yet.
Change-Id: I9b8f5c24a8b0931075a44398571c9b0d54cce6a6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2819
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This uses the new helper function added earlier.
Change-Id: Icdb5d5c51f70eeb7e39e11062276ceb3eb3d9473
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2818
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is updated to handle LynxPoint-H and LynxPoint-LP
and a new wake event is added for the power button.
Boot, suspend/resume, reboot, etc on WTM2
and then check the event log to see if expected events
have been added.
Change-Id: I15cbc3901d81f4fd77cc04de37ff5fa048f9d3e8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2817
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This makes use of the new functions from pmutil.c that take
care of the differences between -H and -LP chipsets.
It also adds support for the LynxPoint-LP GPE0 register block
and the SMI/SCI routing differences.
The FADT is updated to report the new 256 byte GPE0 block on
wtm2/wtm2 boards which is too big for the 64bit X_GPE0 address
block so that part is zeroed to prevent IASL and the kernel
from complaining about a mismatch.
This was tested on WTM2. Unfortunately I am still unable to get an
SCI delivered from the EC but I suspect that is due to a magic
command needed to put the EC in ACPI mode. Instead I verified that
all of the power management and GPIO registers were set to expected
values.
I also tested transitions into S3 and S5 from both the kernel and
by pressing the power button at the developer mode screen and they
all function as expected.
Change-Id: Ice9e798ea5144db228349ce90540745c0780b20a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2816
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The kernel ACPI was not happy with the Add inside a
ResourceTemplate (or perhaps within the IO declaration)
Instead make a buffer of IO reservations and turn _CRS
into a method that updates the buffer depending on the
chipset type.
This adds an \ISLP() method that checks the chipset LPC
device ID to see if it is -LP or -H.
It also increases the PM base reservation to 256 bytes
and moves both GPIO and PM base to above 0x1000 on -LP
chipsets.
Change-Id: I747b658588a4d8ed15a0134009a7c0d74b3916ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2815
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This was put in for debugging and experimentation on i945
and has been copied around since. Drop it from lynxpoint.
Change-Id: I0b53f4e1362cd3ce703625ef2b4988139c48b989
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2814
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There are subtle yet significant differences in some of the
registers in the power management region between LynxPoint-H
and LynxPoint-LP.
In order to reduce code that is accessing these registers and
would need special cases this adds a number of helper functions
that can be used in both ramstage and SMM.
This commit just adds the new functions, subsequent commits will
start to use them.
Change-Id: I411da75da519f5b3198a408078cbf3114e426992
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2813
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These base addresses are used in several places and it
is helpful to have one location that is reading it.
Change-Id: Ibf589247f37771f06c18e3e58f92aaf3f0d11271
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2812
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a helper function pch_is_lp() that will return 1 if
the current chipset is of the new "low power" variant used
with Haswell ULT.
Additionally these functions are added to SMM so it can
be used there.
Change-Id: I9acdea2c56076cd8d9627aba66cf0844c56a38fb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2811
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In order to be able to talk to an EC via standard path.
Change-Id: I3fe76882dec9a0596cbc1c844afa2ddb03ed771c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2810
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
I'm not sure if I screwed this up originally or the Intel docs changed
(I didn't bother to go back and check). According to ME BWG 1.1.0 the give
up bit is in the host general status #2 register.
Change-Id: Ieaaf524b93e9eb9806173121dda63d0133278c2d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2808
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
So it can get used in both romstage and ramstage.
Change-Id: Ief9eaafdd91df2a7b668de1a9b83aea3af3ff894
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2802
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
SPI accesses can be slow depending on the setup and the access pattern.
The current SPI hardware setup to cache and prefetch. The alternative
cbfs_load_payload() function takes advantage of the caching in the CPU
because the ROM is cached as write protected as well as the SPI's
hardware's caching/prefetching implementation. The CPU will fetch
consecutive aligned cachelines which will hit the ROM as
cacheline-aligned addresses. Once the payload is mirrored into RAM the
segment loading can take place by reading RAM instead of ROM.
With the alternative cbfs_load_payload() the boot time on a baskingridge
board saves ~100ms. This savings is observed using cbmem.py after
performing warm reboots and looking at TS_SELFBOOT_JUMP (99) entries.
This is booting with a depthcharge payload whose payload file fits
within the SMM_DEFAULT_SIZE (0x10000 bytes).
Datapoints with TS_LOAD_PAYLOAD (90) & TS_SELFBOOT_JUMP (99) cbmem entries:
Baseline Alt
-------- --------
90:3,859,310 (473) 90:3,863,647 (454)
99:3,989,578 (130,268) 99:3,888,709 (25,062)
90:3,899,450 (477) 90:3,860,926 (463)
99:4,029,459 (130,008) 99:3,890,583 (29,657)
90:3,834,600 (466) 90:3,890,564 (465)
99:3,964,535 (129,934) 99:3,920,213 (29,649)
Booted baskingridge many times and observed 100ms reduction in
TS_SELFBOOT_JUMP times (time to load payload).
Change-Id: I27b2dec59ecd469a4906b4179b39928e9201db81
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2783
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
At some point, compiles with USB Debug port stopped working. This change makes
a trivial reordering in the code and adds two makefile entries to make it build
without errors. It also works on stout.
Build and boot as normal. Works. Enable CONFIG_USB, connect USB debug hardware
to the correct port (on stout, that's the one on the left nearest the back) and
watch for output.
Change-Id: I7fbb7983a19b0872e2d9e4248db8949e72beaaa0
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2784
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Rather than have to repeat this bit in every mainboard.
Also, remove the reset of the RTC power status from here.
We had done this in TOT for current platforms but did not
carry it back to emeraldlake2 where this branched from.
If we clear the status here then we don't get an event
logged later which can be important for the devices that
do not have a CMOS battery.
Change-Id: Ia7131e9d9e7cf86228a285df652a96bcabf05260
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2683
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This commit adds support for using the SMM modules for haswell-based
boards. The SMI handling was also refactored to put the relocation
handler and permanent SMM handler loading in the cpu directory. All
tseg adjustment support is dropped by relying on the SMM module support
to perform the necessary relocations.
Change-Id: I8dd23610772fc4408567d9f4adf339596eac7b1f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2728
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Some initialization steps were done twice
- One step was missing for Panther Point HDA
- Added a 1ms delay after reset
- Increased timeout to 1ms for all codec operations
Change-Id: Ib751f1a16ccd88ea2fbbb2a10737f76277574026
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2518
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There was a mix of setup code sprinkled across the various components:
southbridge code in the northbridge, etc. This commit reorganizes the
code so that northbridge code doesn't initialize southbridge components.
Additionally, the calling dram initialization no longer calls out to ME
code. The main() function in the mainboard calls the necessary ME
functions before and after dram initialization.
The biggest change is the addition of an early_pch_init() function
which initializes the BARs, GPIOs, and RCBA configuration. It is also
responsible for reporting back to the caller if the board is being
woken up from S3. The one sequence difference is that the RCBA config
is performed before claling the reference code.
Lastly the rcba configuration was changed to be table driven so that
different board/configurations can use the same code. It should be
possible to have board/configuration specific gpio and rcba
configuration while reusing the romstage code.
Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2681
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Certain SATA devices claim to support SATA 6 Gbps, but in fact have
bugs. For these devices, add a config option to force the SATA link
speed to something other than default.
Change-Id: I2dc1793cd58771298a392345162d39d20eb0afbb
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/2765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This enables power management and clock gating on XHCI.
Change-Id: I124ea6c5aca034b7ec4b5286d971c2adfce25c88
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
objcopy -B provides symbols of the form _binary_<name>_(start|end|size).
However, the _size variant is an absoult symbol. If one wants to
relocate the smi loading the _size symbol will be relocated which is
wrong since it is suppose to be a fixed size. There is no way to
distinguish symbols that shouldn't be relocated vs ones that can.
Instead use the _start and _end variants to determine the size.
Change-Id: I55192992cf36f62a9d8dd896e5fb3043a3eacbd3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2760
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The bd82x6x requires some additional setting on S3/S4 entry.
Change-Id: I24489ab94dd7cd5a4a64044f25153f5b01a45b77
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2759
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add the PCH function to SMM for follow-on SMM patches that
require these functions.
Change-Id: I7f3a512c5e98446e835b59934d63a99e8af15280
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2758
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These enables are hidden behind IOBP for some reason.
Boot to linux with SDIO disabled and see that
the SDIO driver does not load and crash the system.
Change-Id: Icfbfa117e9e57a51d32db7f6366a9d0d790adcf0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2695
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This commit updates the Lynx Point resource reservations before
the coreboot allocator assigns resources. There is no need to mark
anything as subtractive decode because there are no devices/buses
linked to the LPC device.
The I/O range reservations consists of claiming the first 4KiB
of I/O space. The PMBASE, GPIOBASE, and LPC generic I/O decode
ranges are checked against the default claimed range. If those
ranges overlap or fall outside of the default range then those
resources are added.
The MMIO range reservations consist of claiming everything from
the I/O APIC to 4GiB. The RCBA and the LPC Generic Memory range
register are then conditionally added if they fall outside of
the default MMIO range.
Change-Id: I0f560a03814a2b15961fdbe61e4164cd54cff7a5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2682
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Add ME device ID for Lynxpoint LP
- Add GPU device IDs for ULT
- SATA init tweaks from checking against DXE reference code
- Remove the ICH7 from the SPI driver so it works on all lynxpoint
without having to add more LPC device ID checks
- Add function disable for audio dsp and xhci, remove PCI bridge
- Add interrupt route registers for new devices (needs romstage setup)
Change-Id: Idb48f50d0bacb6bf90531c3834542b9abb54fb8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2680
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Add device IDs for lynxpoint mobile and LP variants.
- Update the clock gating setup based on BWG
- Update the SATA programming based on BWG
- Add a DEVSLP0 mux config register
Change-Id: Icf4d7bab7f3df7adef5eb7c5e310a6995227a0e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2649
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The low power variant of the chipset introduces a completely
new interface to the GPIOs.
This is a 1KB region and so needs to be moved as well so it does
not conflict with other IO regions.
Also expose the gpio_get functions to ramstage and move the
prototypes to pch.h so they can be used for both GPIO interfaces.
Change-Id: I20bc18669525af16de8cdf99f0ccfa9612be63ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2648
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
There are enough subtle differences that it is useful to have
a Kconfig entry to differentiate the ULT/LP chipet from the
desktop/mobile versions.
Change-Id: I04ca1bc6f90bcf9e6994ea7125c98347e8def898
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2645
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
