summaryrefslogtreecommitdiff
path: root/src
AgeCommit message (Collapse)Author
2020-08-22drivers/spi/tpm: Add helper to get cr50 firmware versionKarthikeyan Ramasubramanian
Introduce a helper to get the cached cr50 firmware version. This information is in turn used to identify the strap configuration supported by Cr50. BUG=None TEST=Ensure that Drawcia board boots to OS. Ensure that the version cached cr50 firmware version is returned. Change-Id: Id84b152993f253878a6c133cc433a0da2c990cf2 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44653 Reviewed-by: Edward O'Callaghan <quasisec@chromium.org> Reviewed-by: Sam McNally <sammc@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-21mb/google/zork/var/ezkinil: Fix stylus GPIO to enable suspendJosie Nordrum
Make GPIO_4 and GPIO_5 PAD_NC in ezkinil/gpio.c. None of the Ezkinil SKUs use internal stylus and hence pen pads are configured as NC. BUG=b:164892883, b:165342107 TEST=Verified taht pen detect GPIO does not cause spurious wakes. BRANCH=None Signed-off-by: Josie Nordrum <josienordrum@google.com> Change-Id: I7557575cf8b8e0f849e05bda1d69acf61e91a157 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44629 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-21superio/ite: delay PWRGD3 during resumeMichael Büchler
According to the IT8728F datasheet it is possible to add an extra delay between 3VSBSW# being set and PWRGD3 being set during resume from Suspend-to-RAM. This is enabled in the special function selection register, the default being 0. This is also useful for the IT8720F although this chip does not have the PWRGD3 output. On the corresponding pin it has PWROK2, which the setting then seems to apply to. The datasheet for the IT8720F marks the corresponding bit as reserved, but the vendor BIOS of an Acer Aspire M3800 sets it anyway. Without setting the bit, coreboot fails to resume from S3. Oscilloscope measurements have shown that setting the bit increases the delay between 3VSBSW# being set and PWROK2 being set from around 1 us to 140 ms. The actual use of PWROK2 on the board design is unclear - the only destination it seems to reach is a pin header near the SuperIO marked as "GPIO1". Signed-off-by: Michael Büchler <michael.buechler@posteo.net> Change-Id: I51cbf2470dc2b840a647a20090acb5a0cf4f4025 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44639 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2020-08-21lib: Update fmap cache error for psp_verstageMartin Roth
The assumption was that the fmap cache would be initialized in bootblock, otherwise an error is shown. This error is showing up in psp_verstage when the fmap cache is initialized there, so create a new ENV value for ENV_INITIAL_STAGE. BUG=None TEST=Boot, see that error message is gone from psp_verstage Signed-off-by: Martin Roth <martinroth@chromium.org> Change-Id: I142f2092ade7b4327780d423d121728bfbdab247 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43488 Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Raul Rangel <rrangel@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-21soc/amd/picasso: If using VBOOT, skip the APOB_NV region for ROMartin Roth
When booting from the RO region of a VBOOT enabled ROM, there shouldn't be a reliance on anything outside of the RO section. This includes the APOB_NV region (similar to the MRC cache region). By skipping the region when setting up the BIOS Directory table, the PSP won't try to use the region when booting. The APOB_NV region is still used for the VBOOT RW sections. BUG=b:158363448 TEST=Build RO with no APOB_NV region. Dump the BDT and verify that it's not in RO, but is in RW_A & RW_B. Boot into recovery. Signed-off-by: Martin Roth <martinroth@chromium.org> Change-Id: I13c35ba8a2331492744d2acf257db15e4a53102a Reviewed-on: https://review.coreboot.org/c/coreboot/+/44046 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-08-21mb/google/zork: provide full range backlight settings to kernelAaron Durbin
Utilize the SOC_AMD_COMMON_BLOCK_GRAPHICS_ATIF option to provide full range backlight settings to the kernel. BUG=b:163583825 Change-Id: I3c337fad38e668488800f4d6bc583a82a93659d3 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44643 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-08-21soc/amd/common: add rudimentary ATIF supportAaron Durbin
The Linux kenerl driver for AMD gpu currently has a floor value of 12 for brightness settings (AMDGPU_DM_DEFAULT_MIN_BACKLIGHT). AMD indicates they did this because they were concerned with certain panels flickering at lower backlight values. However, for unaffected panels it's desirable to be able to have the panel "turn off" at the lowest backlight setting. The only way to do that is to provide ATIF bindings that indicate backlight range. Option SOC_AMD_COMMON_BLOCK_GRAPHICS_ATIF is added to provide a full range for the backlight setting. If needed, this path can be built upon for fuller support, but for the time being this is the only thing necessary to make the backlight be full range. BUG=b:163583825 Change-Id: If76801a8daf6a5e56ba7d118956f3ebce74e567a Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44642 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-08-21acpi: add more AML generation functionsAaron Durbin
Add the following functions to acpi AML generation code: acpigen_write_to_integer_from_namestring() acpigen_write_create_byte_field() acpigen_write_create_word_field() acpigen_write_create_dword_field() acpigen_write_create_qword_field() BUG=b:163583825 Change-Id: Ida151aff68f90012b16df2383fb96ddb87c3fb9c Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44641 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-21arch/x86/gdt: Work around assembler bugPatrick Rudolph
The GDT loading did work fine on x86_64 a few months ago, but today it only works in QEMU, but not on real hardware or KVM-enabled QEMU. This might be related to toolchain changes. Use 64bit GDT loading on x86_64 and force the assembler to generate a 64bit address load on the GDT. This will make sure no 32bit (signed) displacement op is being generated, which points to the wrong address in longmode. Verified using readelf and made sure no R_X86_64_32S relocation symbol is emitted. Disassembled the romstage ELF and made sure the GDT address is 64bit in size. Tested on QEMU and KVM-enabled QEMU: Doesn't crash any more on KVM. Signed-off-by: Patrick Rudolph <siro@das-labor.org> Change-Id: Ia824f90d9611e6e8db09bd62a05e6f990581f09a Reviewed-on: https://review.coreboot.org/c/coreboot/+/43136 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-08-21include/asan.h: Add missing includesElyes HAOUAS
<stdint.h> and <stddef.h> are missing. Change-Id: I10520013bb5ceb3aec0d24715f371f77e4300a70 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44656 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Idwer Vollering <vidwer@gmail.com>
2020-08-21mb/purism/librem_whl: Convert GPIOs to macrosMatt DeVillier
Convert raw GPIOs to coreboot macros using newly-added support for Cannon/Whiskey/Coffee/Cometlake SoCs to intelp2m Test: build/boot Librem Mini, no smoke released. Change-Id: I6ac747ad4e650c24d2b7e34228ff74140c51a0c1 Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44503 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
2020-08-21mb/intel/tglrvp: Disable TBT_PCIE3 for UP4John Zhao
Tiger Lake External Design Specification (Document #575683) states UP4 TBT_PCIE3 is not applicable. Disable TC3 for UP4. BUG=None Test=Built UP4 image successfully. Signed-off-by: John Zhao <john.zhao@intel.com> Change-Id: Icff8fccf9ac29c315c2a4dd08a3ec8a8efe9c453 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44572 Reviewed-by: Caveh Jalali <caveh@chromium.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-21mb/google/dedede: Enable IPU for Wdoo and Wdee variantsMaulik V Vaghela
IPU is required to be enabled for platform supporting MIPI camera. IPU is by default disabled in devicetree for all variants. Enable IPU for Waddledoo and Waddledee supporting MIPI camera. BUG=None BRANCH=None TEST=IPU is enabled for platforms and enumerates in lspci. Change-Id: Ia3cf06d78be4301c68bfa8b1118ddff231d24a66 Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44271 Reviewed-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-21SMM: Validate more user-provided pointersPatrick Rudolph
Mitigate issues presented in "Digging Into The Core of Boot" found by "Yuriy Bulygin" and "Oleksandr Bazhaniuk" at RECON-MTL-2017. Validate user-provided pointers using the newly-added functions. This protects SMM from ring0 attacks. Change-Id: I8a347ccdd20816924bf1bceb3b24bf7b22309312 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Signed-off-by: Christian Walter <christian.walter@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41086 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-08-21sb/intel/i82371eb/fadt.c: Use macro for 'flags' instead of magic numberElyes HAOUAS
Change-Id: I793afe81fbb9abef0d4178af9dc2e91c612b1b43 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44521 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-21soc/intel/tigerlake: Enable long cr50 ready pulsesJes Klinke
A new Kconfig setting CR50_USE_LONG_INTERRUPT_PULSES controls new code running in verstage, which will program a new Cr50 register, to have Cr50 generate longer than default interrupt pulses. This needs to be selected on all Tiger Lake systems, since Tiger Lake (and likely future Intel SoCs) require at least 100us interrupt pulses. TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x BUG=b:154333137 Change-Id: I20100d72ce426203943c1788d538bb2cd9d82e11 Signed-off-by: Jes Bodi Klinke <jbk@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44626 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-08-21arch/x86: Add support for ASan to memory functionsHarshit Sharma
Compiler's instrumentation cannot insert asan memory checks in case of memory functions like memset, memcpy and memmove as they are written in assembly. So, we need to manually check the memory state before performing each of these operations to ensure that ASan is triggered in case of bad access. Change-Id: I2030437636c77aea7cccda8efe050df4b77c15c7 Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44307 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-08-21mainboard/emulation/qemu-i440fx: Select HAVE_ASAN_IN_ROMSTAGEHarshit Sharma
Enable ASan in romstage as it has been tested. Change-Id: I3b5263f5342a78968d9a1ecf72996fff0946b204 Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44282 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-08-21soc/intel/apollolake: Select HAVE_ASAN_IN_ROMSTAGEHarshit Sharma
Enable ASan in romstage for apollolake as it has been tested on Siemens MC-APL3. Change-Id: I2f2f965151a4ef4672f2f16979a6ad8492879aeb Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44159 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-08-21cpu/intel/haswell: Select HAVE_ASAN_IN_ROMSTAGEHarshit Sharma
Enable ASan in romstage for haswell as it has been tested on Lenovo ThinkPad T440P. Change-Id: I6eae242c71f41c9159658ae68d61b4036ad42d42 Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44160 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-08-21arch/x86: Select HAVE_ASAN_IN_RAMSTAGEHarshit Sharma
Enable ASan in ramstage if ASAN is selected in menuconfig for an x86 platform. Change-Id: Id5b3dc18368a5da6bdc70c84527b95d1688dc19f Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44259 Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-21Kconfig: Update ASan config optionsHarshit Sharma
Instead of enabling ASAN_IN_ROMSTAGE from Kconfig file in a platform's dedicated directory, let's introduce a new config option HAVE_ASAN_IN_ROMSTAGE to denote if a given platform supports ASan in romstage. Similary, use HAVE_ASAN_IN_RAMSTAGE to indicate if a given platform supports ASan in ramstage. Consequently, we no longer have to make ASan x86 specific. Change-Id: I36b144305465052718f245cacf61d3ca44dfb4b4 Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44258 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-08-21lib: Add ASan support to romstage on x86 archHarshit Sharma
This patch adds ASan support to romstage on x86 architecture. A Kconfig option is added to enable ASan in romstage. Compiler flags are updated. A memory space representing the shadow region is reserved in linker section. And a function call to asan_init() is added to initialize shadow region when romstage loads. Change-Id: I67ebfb5e8d602e865b1f5c874860861ae4e54381 Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43604 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-08-21lib: Add ASan support to ramstage on x86 archHarshit Sharma
This patch adds address sanitizer module to the library and reserves a linker section representing the shadow region for ramstage. Also, it adds an instruction to initialize shadow region on x86 architecture when ramstage is loaded. Change-Id: Ica06bd2be78fcfc79fa888721ed920d4e8248f3b Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42496 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-08-21lib: Update ASan compiler flags and Kconfig help textHarshit Sharma
An additional compiler flag is added to make use of the shadow offset callback feature we introduced in our GCC patch. Also, a comment is added to tell user that this GCC patch needs to be applied in order to use ASan. Change-Id: Ia187e4991bf808f4ae137eff0ffdb9baea0085e9 Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43164 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-08-21lib: Add ASan stubHarshit Sharma
Add a Kconfig option to enable address sanitizer on x86 architecture. Create ASan dummy functions. And add relevant gcc flags to compile ramstage with ASan. Change-Id: I6d87e48b6786f02dd46ea74e702f294082fd8891 Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42271 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-08-21mb/google/asurada: Fixup BOOT_DEVICE_SPI_FLASH_BUS default valueCK Hu
On MT8192 the SPI flash is actually using a SPI-NOR controller with its own bus. The number here should be a virtual value as (SPI_BUS_NUMBER + 1). Signed-off-by: CK Hu <ck.hu@mediatek.com> Change-Id: Ibc269201a34968c8400d2235e8da2ecd88114975 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44452 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2020-08-20cse_lite: Move global reset after MRC writebackCaveh Jalali
With CSE-lite enabled, we were going through the lengthy memory training procedure twice on the first power-on boot or after full BIOS SPI flash update. This moves the global reset performed to achieve the CSE-lite RO to RW reboot to a later boot phase so that it happens after the memory training data has been written to the MRC cache. Now, the 2nd (and subsequent) reboot can utilize the memory training data established during the 1st boot. This reduces the first boot time by about 20s on a 16GB system. Looking at the timing stats form cbmem, the normal boot penalty is about 300ms - mostly attributed to running FspSiliconInit a 2nd time. We will get this time back when the mrc_cache refactoring effort lands (cb:44196, et. al). BUG=b:162021048 TEST=Booted on volteer, confirmed 20s faster boot time. Change-Id: Ia42d72fdec41f9792ab8f04205b20a55758a4235 Signed-off-by: Caveh Jalali <caveh@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44430 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2020-08-20soc/amd/acpi: Move ACPI IVRS generation to corebootJason Glenesk
Add code for IVRS generation to coreboot. Publish coreboot generated structure rather than IVRS generated by FSP binary. Reference Doc: 48882_IOMMU_3.05_PUB.pdf BUG=b:155307433 TEST=Boot trembyle to shell and extract and compare IVRS tables and make sure they cover the same devices. Change-Id: I693f4399766c71c3ad53539634c65ba59afd0fe1 Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43804 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2020-08-20drivers/spi/tpm: Enable long cr50 ready pulses for Tiger Lake systemsJes Klinke
For Volteer (and future Tiger Lake boards) we can enable mode S0i3.4 only if we know that the Cr50 is generating 100us interrupt pulses. We have to do so, because the SoC is not guaranteed to detect pulses shorter than 100us in S0i3.4 substate. A new Kconfig setting CR50_USE_LONG_INTERRUPT_PULSES controls new code running in verstage, which will program a new Cr50 register, provided that Cr50 firmware is new enough to support the register. BUG=b:154333137 TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x Signed-off-by: Jes Bodi Klinke <jbk@chromium.org> Change-Id: If83188fd09fe69c2cda4ce1a8bf5b2efe1ca86da Reviewed-on: https://review.coreboot.org/c/coreboot/+/43741 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Julius Werner <jwerner@chromium.org>
2020-08-20src/mainboard: Escape variable expansion in KconfigPatrick Georgi
Kconfig 5.8 interprets $(...) itself using environment variables, which generally means that they expand to the empty string. \$(...) works with both our current and new Kconfig with the desired behavior (to pass it through unmodified). Change-Id: I726567eeb61d2035560152677d2b4548c1472be9 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44584 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-20mb/asrock/b85m_pro4: Select PECI function on Super I/OAngel Pons
This allows the Super I/O to know how hot the CPU is. Change-Id: I9c91136c3bb5aae541bb7ac64bb62be36c3c0b5d Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44552 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2020-08-20sb/intel/lynxpoint: Drop unneeded and rotten Kconfig optionAngel Pons
Not selecting `ME_MBP_CLEAR_LATE` results in a build failure. Since both traditional and ULT platforms are known to be working, drop the option. Change-Id: I09ce27f812966800e36f6c0624c93759089faf45 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44547 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2020-08-20mb/asus/am1i-a/buildOpts.c: choose the 1600 MT/s RAM frequencyMike Banon
Together with the "AMD_XMP" changes, now this board with Crucial BLT8G3D1869DT1TX0 sticks could run at 1600 MT/s CL8 (8-8-9-23) speeds. Earlier only 1333 MT/s CL9 (9-9-10-27) has been possible with coreboot. 1866 MT/s CL9 is impossible on f16kb without northbridge overclocking. tRP in "CL-tRCD-tRP-tRAS" gets set 1 point higher by AGESA because of Errata 638. See more info in a BKDG for AMD Family 16h Models 00h-0Fh. Signed-off-by: Mike Banon <mikebdp2@gmail.com> Change-Id: I7e9f5120421221043f9f9dfe143b51bfa61936be Reviewed-on: https://review.coreboot.org/c/coreboot/+/44462 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-20vc/amd/agesa/f16kb: raise the UDIMM Freq limit 1333MT/s values to 1600MT/sMike Banon
AMD f16kb boards are perfectly capable of working at 1600MT/s RAM speeds even with two DDR3 UDIMM modules per channel. AM1I-A only supports a single-channel operation, with at most two DIMMs per channel, so raising these limit values is required to let it and similar boards run faster. Successfully tested on AM1I-A and two Crucial BLT8G3D1869DT1TX0 UDIMMs, together with related AMD_XMP changes - also required to get a 1600MT/s with this set of modules which have only 1333MT/s at JEDEC part of SPD. Signed-off-by: Mike Banon <mikebdp2@gmail.com> Change-Id: I2a9da4e594ab3dc38b5ba87520633cbd01c9ce01 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44461 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-20soc/intel/xeon_sp/cpx/Kconfig: Relocate 'select CACHE_MRC_SETTINGS'Elyes HAOUAS
This will remove the warning: "src/soc/intel/xeon_sp/cpx/Kconfig:79:warning: config symbol 'CPU_BCLK_MHZ' uses select, but is not boolean or tristate" Change-Id: I2cfaf347b638e3847caa167e7efda89e9202960a Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44548 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
2020-08-19mb/google/zork/baseboard: Remove unused referenceMatt Papageorge
Remove references to clk_pm_support which is currently ignored by Picasso AGESA FSP. BUG=b:161218965,b:162423378 TEST=Build test Trembyle and Dali, boot to ChromeOS 5 times each Change-Id: Ic5d6abc56821863b68e45c11763f00d2b6410983 Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44556 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Justin Frodsham <justin.frodsham@amd.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-19vc/amd/fsp/picasso: update pci descriptor commentsMatt Papageorge
Update fsp_dxio_descriptor comments to be more comprehensive of the currently available data fields. Most of these are not currently utilized with Zork but may be in future projects. BUG=b:161218965 TEST=Build test Trembyle Change-Id: I8eb79fa7807dcf5b28b7b0ec60953ef857d51972 Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44554 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-19mb/google/volteer: Implement weak function `cse_board_reset`Tim Wawrzynczak
Since Volteer also uses the CSE Lite SKU and the cr50, it is subject to a problem where old cr50 FW will not be able to properly detect an SoC reset, so the reset on cold boots caused by the CSE Lite RO->RW jump should instead get an assist from the EC, which can perform a full cold reset. BUG=b:162977697 TEST=Verify EC performs the cold reset Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: Ie8ae21c203da218459d5fd30a23be23520ed0598 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44536 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Caveh Jalali <caveh@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-08-19mb/emulation/qemu-q35,qemu-i440fx: Add x86_64 supportPatrick Rudolph
* Enable optional x86_64 romstage, postcar and ramstage * Add Kconfig for x86_64 compilation * Add documentation for x86 qemu mainboards * Increase CAR stack as x86_64 uses more than 0x4000 bytes Working: * Boots to Linux * Boots to SeaBIOS * Drops to protected mode at end of ramstage * Enumerates PCI devices * Relocateable ramstage * SMM Change-Id: If2f02a95b2f91ab51043d4e81054354f4a6eb5d5 Signed-off-by: Patrick Rudolph <siro@das-labor.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/29667 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-19cpu/x86/64bit/exit32: Add support for ramstagePatrick Rudolph
When compiled in RAMSTAGE use the segments for ramstage. Allows to call this assembly code in ramstage to exit long mode. The next commit makes use of this. Tested on qemu: Still boots on x86_64. Change-Id: I8beb31866bd15afc206b480b1ba05df995adc402 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44504 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-08-19arch/x86/boot: Jump to payload in protected modePatrick Rudolph
* On ARCH_RAMSTAGE_X86_64 jump to the payload in protected mode. * Add a helper function to jump to arbitrary code in protected mode, similar to the real mode call handler. * Doesn't affect existing x86_32 code. * Add a macro to cast pointer to uint32_t that dies if it would overflow on conversion Tested on QEMU Q35 using SeaBIOS as payload. Tested on Lenovo T410 with additional x86_64 patches. Change-Id: I6552ac30f1b6205e08e16d251328e01ce3fbfd14 Signed-off-by: Patrick Rudolph <siro@das-labor.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/30118 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2020-08-19cpu/ti/am335x: Move from cpu to soc in treeSam Lewis
The AM335X is a SoC, so should be in the soc tree. This moves all the existing am335x code to soc/ and updates any references. It also adds a soc.c file as required for the ramstage. Change-Id: Ic1ccb0e9b9c24a8b211b723b5f4cc26cdd0eaaab Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44378 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2020-08-19arch/arm: Enable FIT payloadsSam Lewis
Implements fit_payload_arch for the arm (aarch32) architecture, so that FIT images can be used. The implementation is very similar to the existing implementations for arm64 and riscv, and has mostly been lifted from these other ports. TEST: Booted Beaglebone Black (in progress port, to be submitted soon!) with a FIT image containing a 5.4 kernel, dtb and initramfs. Change-Id: I6b50c6f06b83c00a5b3622b5bbafe67130b6d233 Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44377 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2020-08-19mb/google/volteer: Update settings for trackpad on HalvorJohn Su
Configure gpio settings for trackpad. BUG=b:153680359 TEST=FW_NAME=halvor emerge-volteer coreboot chromeos-bootimage Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Change-Id: I525ba688f71b7a1893bcb64c77e02c8e2506d7b0 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44524 Reviewed-by: Caveh Jalali <caveh@chromium.org> Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-19soc/amd/picasso: log and print GPIO wake eventsAaron Durbin
Capture the GPIO subsystem wake state and add events to the eventlog. BUG=b:159947207 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Change-Id: I7f10bf4599ea7928cc87b6b10ac11a7c30e58406 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44535 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-08-19soc/amd/common: add gpio subsystem event reportingAaron Durbin
In order to log gpio events for wake purposes the state of the gpio subsystem should be snapshotted. Add the ability to capture state of gpio subystem as well as saving up to 16 gpios that indicate their wake status. Likewise, provide the eventlog additions based on state. BUG=b:159947207 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Change-Id: I49fca56c87543aa8aad0eb7da5c5cb570c4349d5 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44534 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-19soc/amd/picasso: Use cbfs to locate the AMD firmwareMartin Roth
Switch from locating the AMD firmware in the RW_A & RW_B regions with their hardcoded locations to using CBFS to find them. They still need to be at the hardcoded locations so that we can set the location inside the binary, but instead of just setting the pointer directly to them, we now search for them with cbfs. BUG=b:154441227 TEST=Boot & verify that binaries are located in both RW-A & RW-B Signed-off-by: Martin Roth <martin@coreboot.org> Change-Id: I27b0593e0db7a9e6ba9b0633ac93b4d93954f002 Reviewed-on: https://review.coreboot.org/c/coreboot/+/42831 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Eric Peers <epeers@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-08-19soc/amd/picasso: Remove now unused #defineMartin Roth
This #define wasn't removed when the tests were removed, so get rid of it now. BUG=None TEST=Build Signed-off-by: Martin Roth <martinroth@chromium.org> Change-Id: Ie0005b6ee97037bf3dfb80f0c2408d8bd9ee9633 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44537 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2020-08-19mb/google/zork: remove unused asl files for dirinbozKevin Chiu
BUG=b:161579679 BRANCH=master TEST=1. emerge-zork coreboot chromeos-bootimage 2. power on proto board successfully Change-Id: I713ac3a47c2d47035affb32e6c604b9af23aa90e Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44514 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 15:23:39 +0000