Age | Commit message (Collapse) | Author |
|
Move the southbridge code to bd82x6x folder similar to the lynxpoint
implementation.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I8afc9f966033f45823f5dfde279e0f66de165e93
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Set default configuration to low for gpio_178, and can remove the
override setting for bobba/bloog/fleex/meep/phaser.
For ampton, Change-Id I64a67f73564188ad0548a1a770169ef2bca47453 (
mb/google/ampton: Fix polarity of EN_PP3300_WLAN_L signal.)
modified the pin setting.
TEST=verified that boot into OS on meep board.
suspend/resume, reboot, and no failure found.
Change-Id: I7668ff4817edfca5c6cea63db779fcea21c7af92
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32247
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Write protection (get_write_protect_state) was hard-coded to 0 and
should be fixed to read from correct GPIO (PERIPHERAL_EN0 from
schematics).
BUG=b:130681408
TEST=make -j; boots on Kukui Rev2.
BRANCH=None
Change-Id: I75b98b1d587abe5e8cdf3df28ea661bc1ffa19f9
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
This patch adds the PCI device ID for cometlake in dsp.c
Change-Id: Ia28e3b9d1dc27ffcf24dfb2ef1efa9ae9c4027c8
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
This patch ensures to follow Intel SDM Vol 3B Sec 18.7.3 to
calculate nominal TSC frequency.
As per SDM recommendation:
For any processor in which CPUID.15H is enumerated and
MSR_PLATFORM_INFO[15:8] (which gives the scalable bus frequency) is
available, a more accurate frequency can be obtained by using CPUID.15H
This patch also adds header file to capture Intel processor model number.
BUG=b:129839774
TEST=Boot ICL platform and calculate TSC frequency using below methods
1. TSC freq calculated based on MSR 0xCE
tsc: Detected 1600.000 MHz processor
2. TSC freq calculated based on CPUID 0x15
tsc: Detected 1612.800 MHz TSC
Method 2 actually reduce ~25ms of boot performance time.
Note: Method 2 is recommended from gen 6 processor onwards.
Change-Id: I9ff4b9159a94e61b7e634bd6095f7cc6d7df87c7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
GPT4 is a 32-bit timer and the counter of GPT4 will overflow in about
330 seconds (0xffffffff / 13MHz). Timer and delay functions will not
work properly if the counter overflows. To fix that we should use the
64-bit timer (GPT6).
BUG=b:80501386
BRANCH=none
Test=emerge-elm coreboot; emerge-kukui coreboot
Change-Id: I9f080e47253a1b1bab4636a45cb86c8666a25302
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
|
|
Change VmxEnable UPD values based on Kconfig ENABLE_VMX
and remove it from Devicetree and chip.h
Remove Vmx dependency on Vt-d
Change-Id: I4180c2270038a28befd6ed53c9485905025a15ba
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32117
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement required soc side API to enable VMX support using CPU_COMMON
BUG=b:124518711
TEST= read msr 0x3a and verify vmx is enabled (value should be 5).
Change-Id: I33dbffa6301afabd688080751ba3b85a43e00156
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use common code to detect ACPI S3.
Tested on Lenovo T520 (Intel Sandy Bridge) with Change
I8afc9f966033f45823f5dfde279e0f66de165e93 applied as well.
Still boots to OS, no errors visible in dmesg and S3 resume is working.
Change-Id: I283a841575430f2f179997db8d2f08fa3978a0bb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use common code to detect ACPI S3.
Untested.
Change-Id: I618d4c25adb0d2b9bbd59a3b3b84beac78db1916
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch performs MP initialization by FSP using coreboot MP
PPI service.
BUG=b:74436746
TEST=Able to perform MP initialization on WHL and CML platform.
Change-Id: I530d50e5aacc3cb9b625df14a50d4c5923e3fb4d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Kukui is using MIPI display panel and needs some identifier to tell
payloads which LCD module is installed, and to select right kernel
device tree. Following Scarlet, the decision is to embed LCD module ID
as part of SKU ID.
The LCM ID is using a different voltage mapping table from the rest.
Considering the complexity in computation of SKU ID, it is better to
move the cache logic from get_index to caller.
Also revise the mapping table since ADC on 8183 only supports 12
levels.
BUG=b:129299873
TEST=make -j; boots on Kukui Rev2 unit.
Change-Id: Ib0c00bc8ce3c71c445c5c4561403ce8ef4dd5844
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32263
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The external RTC was removed on the mainboard as it is not needed.
Remove the usage of the driver for RX6110SA as well.
Change-Id: Ia476e58c0b0f343d4e9e4fa6039bf82b194a87d3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
With commit
'4074ce0cc7 (intel/apollolake: Add HDA to disable_dev function)'
FSP is now requested to switch off HDA PCI device if it is disabled in
devicetree. Doing so results in a warm restart. Normally this event
will be stored in CMOS RAM (if the descriptor is configured to do so)
and therefore no further resets are requested by FSP on the next boots
as long as CMOS RAM is kept alive.
The Siemens mainboards based on Apollo Lake do not have a CMOS battery
and therefore the CMOS is not backed up. This leads to reset requests
from FSP after PCI enumeration on every boot. To avoid this reset enable
HDA in devicetree for these mainboards. Though we do not have any usage
of HDA it should not be an issue that the HDA device is now enabled. The
benefit is though that no reset is requested anymore by FSP.
Change-Id: I637c7c01d73350700c6066fee74fecbb5b93b221
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32295
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the power rail discharge times measured on hatch,
update the assertions widths that have to be programmed in SoC.
BUG=b:129328209
TEST=warm/cold reboot and S3 are working fine on hatch.
Change-Id: I3c6dce0a942e6dcd9e55ef5e58a7e9e8d2b0a1e3
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Laser would prefer to use different SAR values. Since Laser
sku id is 5.
BUG=b:130381493
BRANCH=octopus
TEST=build
Change-Id: I5cce38a191edfb235e274db3c788c58b65e0ebe1
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32296
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This sneaked in after we made unknown arguments to CONFIG() an error.
Change-Id: Ia1de78ce1d3277c7b094c3283455f4b56f3a3fbb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32314
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use common code to detect ACPI S3.
Tested on Thinkpad X60.
Change-Id: Ia759a9ed141efc8130860300f2a8961f0c084d70
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use common code to detect ACPI S3.
Untested.
Change-Id: I87ac56e4ba1fb83761786d5f32a0fc308ee9718a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32039
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use common code to detect ACPI S3.
Untested.
Change-Id: I2264c087b317f70506817b5458295a17e83b1efc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32038
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a common detect_s3_resume function.
Will be used by other southbridge code.
TODO: Merge with soc/intel/common/*/pmclib
Tested on Lenovo T520 (Intel Sandy Bridge) with Change
I283a841575430f2f179997db8d2f08fa3978a0bb applied as well.
Still boots to OS, no errors visible in dmesg and S3 resume is working.
Change-Id: I88023af522afac8164f068b0fbe0eac601aef702
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This patch removes multiple enable/disable function definitions and
make use of single function with argument to know feature status
(enable/disable).
Change-Id: I502cd2497b07e9de062df453ecbb9c11df692f5a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32282
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch replaces multiple IA32_PERF_CTL programming with single
helper function.
TEST=Build and boot WHL and CML platform.
Change-Id: I212daa61aa11191dd832630461b517d3dbedd6e1
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Restore Goodix devicetree config because of the
missing Goodix config when moving from baseboard
devicetree to board level overridetree. And move
PENH from I2C#2 to I2C#1.
BUG=b:124460799
BRANCH=None
TEST=local build and tested with Goodix touch screen
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic028c5d7b687a069d7f0510897bea91dca58e91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Cannon Lake and family require that FSP-M component should be
XIP. This change selects FSP_M_XIP so that the right arguments are
passed into cbfstool when adding this component.
BUG=b:130306520
TEST=Verified that hatch boots fine to OS.
Change-Id: Ifd8a829ebdc7681c81ece4540aa38cdcea7b6fac
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change uses GPIO IRQ instead of IOAPIC for GPP_A0 pad which is
the interrupt line for sx9310. This is required because IRQ# used by
GPP_A0 is allocated for PIRQ which does not allow IRQ# sharing.
Additionally, this change also configures GPP_A6 for GPIO IRQ. GPP_A6
is currently unused in the devicetree.
BUG=b:129794308
TEST=Verified that there are no interrupt storms on GPP_A0.
Change-Id: Ibb510a647391c0d9cb854d23656bb4b1cb7756ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This change adds support for mainboards to use GPIO IRQ instead of
IOAPIC to accomodate for cases where IOAPIC routing might not be
available for certain pads.
BUG=b:129794308
Change-Id: I3e2bb4280303cea177cc0c803d29140731e2b44a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32273
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change configures reset config for all pads routed to IOAPIC as
PLTRST. This is required to ensure that the internal logic of the GPIO
gets reset any time the platform enters S3 or powers off and avoids
any interrupt storms on boot-up.
BUG=b:129933011
TEST=Verified that there are no interrupt storms on boot-up from S5.
Change-Id: Ib790280c9f1410fa18746d4d7d2a5027afd7585b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
XIP_ROM_SIZE Kconfig option isn't used on Cannon Lake and
family. Thus, this change selects NO_FIXED_XIP_ROM_SIZE to indicate to
build system so that romstage can be placed in less rigid manner.
BUG=b:129802811
Change-Id: I5f3786396246c89b1039ba1b6b332a32e6a0345d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
UART0 is already configured in coreboot, so this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in FSP.
BUG=b:130325418
Change-Id: Ifc88f4fa11bff2144417d5194776c15f9f7b60ac
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Move Winbond M25PXX command values to spi_winbond.h
file.
The command values will be used for programming SPI
contoller of Intel Braswell, using this include file.
Update winbond.c file with coreboot header.
BUG=N/A
TEST=Facebook FBG-1701 with flashrom
Change-Id: I9c17c4ed7004209bd3c619d47a7474b0b7e17495
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
FSP code will default enable the onboard serial port.
When external serial port is used, this onboard port needs to be
disabled.
Add function mainboard_after_memory_init() function to perform
required actions to re-enabled output to external serial port.
BUG=N/A
TEST=LPC Post card on Intel Cherry Hill
Change-Id: Ibb6c9e4153b3de58791b211c7f4241be3bceae9d
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Adds virtual logical devices numbers for the Nuvoton (NCT6791D)
SuperIO to the devicetree.
Change-Id: I7df1633951c30fef14c62c89aaedebd3044b312f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add the new configuration 'Krane' that will need at least its own EC.
There's currently no difference in coreboot side.
BUG=b:130011505
TEST=make menuconfig; make -j # select board=Krane
BRANCH=None
Change-Id: Ibb2ec42b08f9a51b22c22f3fe99b203f5eb31627
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Element Self Description register (ESD) [23:16] is R/WO, so let
write the ESD.CID when we start ich7_setup_root_complex_topology.
This value is also used to program the R/WO 'Target Component ID'
registers of RPxD and HHD.
Once it is done, no need to rewrite on them as they become RO.
(For more information, please see ICH7 datasheet page 271.)
Tested done on 945G-M4 using printk before and after writing.
Before this change, writing on those registers had no effect:
ESD: 0x0104: 0x00000802
ULD: 0x0110: 0x00000001
ULBA: 0x0118: 0x00000000
RP1D: 0x0120: 0x01000003
RP2D: 0x0130: 0x02000003
RP3D: 0x0140: 0x03000002
RP4D: 0x0150: 0x04000002
HDD: 0x0160: 0x0f000002
RP5D: 0x0170: 0x05000002
RP6D: 0x0180: 0x06000002
Using this patche, those R/WO get the "right" values.
i.e., We can see RCBA32(ULBA) is now equal to (uintptr_t)DEFAULT_DMIBAR.
ESD: 0x0104: 0x00020802
ULD: 0x0110: 0x01010001
ULBA: 0x0118: 0xfed18000
RP1D: 0x0120: 0x01020003
RP2D: 0x0130: 0x02020003
RP3D: 0x0140: 0x03020002
RP4D: 0x0150: 0x04020002
HDD: 0x0160: 0x0f020002
RP5D: 0x0170: 0x05020002
RP6D: 0x0180: 0x06020002
Change-Id: I3f2199d6da22ce9995496c2a81363710edde81f3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30993
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on HW change, reserve gpio pins for D3 cold control.
A13,A15 for Card reader
H13 for M.2 SSD
BUG=b:123263562
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib4245be8d77c015e56df7b1d53ef82722c51d656
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Three GPIOs are not being used and this change will save 2-3mW
power during S0iX and this power saving is only for Arcada
BUG=b:129990365
TEST= Measure total platform power during S0iX from Arcada
Change-Id: Ie0208bd6c7affb2e87fd76005b727ea7effdf434
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
There will be an out of bounds read if the index is equal
to the array size. Fix the checks to exclude this case.
Found-by: Coverity Scan, CID 1347350, 1347351
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I5b4e8febb68dfd244faf597dfe5cdf509af7a2ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This implementation corrects the GPE DWx mapping for GPIO groups.
The assignments is done in GPIO MISCFG register for all GPIO communities.
And configures the which GPIO communities get register as Tier1.
BUG=b:121212459
TEST: Verified the GPIO MISCFG is getting set as per updated map.
Change-Id: I451997367025a6dc9e5931bd649524e935ad6aca
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32175
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
WiFi enable signal was configured and driven as active-high, but the signal is |To start the server in this Emacs process, stop the existing
actually active-low
BUG=b:130196983
BRANCH=none
TEST=Verified WiFi still works after boot, and also after a suspend/resume cycle. Device powers down correctly using "poweroff".
Change-Id: I64a67f73564188ad0548a1a770169ef2bca47453
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32255
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The value of "write protect" GPIO shall be read in depthcharge,
and the flag shall be set there instead.
BUG=b:124141368, b:124192753, chromium:1556855
TEST=Build locally
CQ-DEPEND=CL:1556855
BRANCH=none
Change-Id: I4d24a057b1385244a836a67c565ee6726a894fdc
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The "write protect" GPIO's cached value is never actually
read after entering depthcharge. Ensure the value from
get_write_protect_state() is being transferred accurately,
so that we may read this GPIO value in depthcharge without
resampling.
The cached value of the "recovery" GPIO is read only on certain
boards which have a physical recovery switch. Correct some of
the values sent to boards which presumably never read the
previously incorrect value. Most of these inaccuracies are from
non-inverted values on ACTIVE_LOW GPIOs.
BUG=b:124141368, b:124192753, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic17a98768703d7098480a9233b752fe5b201bd51
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
For Kukui CR50_IRQ pin, we're going to replace external pull-up with
internal pull-up. This change won't break older boards, so we can just
always do that when setting up GPIOs.
BUG=b:124821269
BRANCH=none
TEST=Waveform looks correct.
Change-Id: Ib1a90dce583a6aa0cec8ac8ba96d1362f50c16a8
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
ODM reported issues that some systems can't be shutdown to S5 very
occasionally.
ODM found issue is gone if they remove the WLAN card.
So, this change to disable WLAN before system enters S5.
This change is validated by ODM and it does help issue.
BUG=b:129377927
Change-Id: Ib8e81022b8c9b63bc75e5cc14121233222da7595
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32246
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Chen Wisley <wisley.chen@quantatw.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Idcdbbfa883c906db1ebb8d9bc7c9e277e7c0c949
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: I6095c3b30990b530c5bc4e2c808879252680e1d7
Signed-off-by: Andrea Barberio <barberio@fb.com>
Signed-off-by: David Hendricks <dhendrix@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
If the entire array is zero, then the length of the
longest zero run is the length of the array itself.
Found-by: Coverity Scan, CID 1229715
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: Id23292087b14182448d70117915fb044e9c579f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This pin should be set to its alternative function SRCLKENA0 instead of
GPIO, so that SPM (a power management component of MT8183) can control
it.
BUG=b:113367227
BRANCH=none
TEST=1. Boot. Run 'powerinfo' in EC console and see power state in S0.
2. Run 'powerd_dbus_suspend --wakeup_timeout=10', and then
run 'powerinfo' in EC console and see power state in S3.
3. Wait until AP resume.
4. Run 'powerinfo' in EC console and see power state back to S0.
Change-Id: I0a7e34f95381dec17eb6d166d6552c12e021bd9a
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32120
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a fmd file for 16MiB fmap, so that we can support
both 16MiB / 32MiB SPI flash ROM chips.
BUG=b:129464811
TEST=build hatch firmware image with 16MiB fmap and
verify fmap is updated by 'fuility dump_fmap'
Change-Id: Ifc0103c7fd0d99439f40a31d23422401a6dce826
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fill in the handle to cache entries of type 7 in the type 4 structure.
Tested on Intel Sandy Bridge (Lenovo T520).
All 3 caches are referenced.
Change-Id: Idf876b0c21c65f72a945d26c5898074b140763f8
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|