From 4b933948720bac217e007f8db17355468e632c32 Mon Sep 17 00:00:00 2001 From: "Ronald G. Minnich" Date: Thu, 14 Oct 2004 21:40:58 +0000 Subject: more breakage, thanks to Ron git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1665 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1 --- src/mainboard/arima/hdama/Config.lb | 385 ++++++----------------------------- src/mainboard/arima/hdama/Options.lb | 124 +++++++++++ 2 files changed, 189 insertions(+), 320 deletions(-) create mode 100644 src/mainboard/arima/hdama/Options.lb (limited to 'src/mainboard/arima') diff --git a/src/mainboard/arima/hdama/Config.lb b/src/mainboard/arima/hdama/Config.lb index f8091bdbe8..c5ed005f80 100644 --- a/src/mainboard/arima/hdama/Config.lb +++ b/src/mainboard/arima/hdama/Config.lb @@ -1,127 +1,3 @@ -uses HAVE_MP_TABLE -uses HAVE_PIRQ_TABLE -uses USE_FALLBACK_IMAGE -uses HAVE_FALLBACK_BOOT -uses HAVE_HARD_RESET -uses HARD_RESET_BUS -uses HARD_RESET_DEVICE -uses HARD_RESET_FUNCTION -uses IRQ_SLOT_COUNT -uses HAVE_OPTION_TABLE -uses CONFIG_MAX_CPUS -uses CONFIG_IOAPIC -uses CONFIG_SMP -uses FALLBACK_SIZE -uses ROM_SIZE -uses ROM_SECTION_SIZE -uses ROM_IMAGE_SIZE -uses ROM_SECTION_SIZE -uses ROM_SECTION_OFFSET -uses CONFIG_ROM_STREAM -uses CONFIG_ROM_STREAM_START -uses PAYLOAD_SIZE -uses _ROMBASE -uses XIP_ROM_SIZE -uses XIP_ROM_BASE -uses STACK_SIZE -uses HEAP_SIZE -uses USE_OPTION_TABLE -uses LB_CKS_RANGE_START -uses LB_CKS_RANGE_END -uses LB_CKS_LOC -uses MAINBOARD_PART_NUMBER -uses MAINBOARD_VENDOR -uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID -uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID - - -## ROM_SIZE is the size of boot ROM that this board will use. -default ROM_SIZE=524288 - -### -### Build options -### - -## -## Build code for the fallback boot -## -default HAVE_FALLBACK_BOOT=1 - -## -## Build code to reset the motherboard from linuxBIOS -## -default HAVE_HARD_RESET=1 - -default HARD_RESET_BUS=1 -default HARD_RESET_DEVICE=4 -default HARD_RESET_FUNCTION=0 - -## -## Build code to export a programmable irq routing table -## -default HAVE_PIRQ_TABLE=1 -default IRQ_SLOT_COUNT=9 - -## -## Build code to export an x86 MP table -## Useful for specifying IRQ routing values -## -default HAVE_MP_TABLE=1 - -## -## Build code to export a CMOS option table -## -default HAVE_OPTION_TABLE=1 - -## -## Move the default LinuxBIOS cmos range off of AMD RTC registers -## -default LB_CKS_RANGE_START=49 -default LB_CKS_RANGE_END=122 -default LB_CKS_LOC=123 - -## -## Build code for SMP support -## Only worry about 2 micro processors -## -default CONFIG_SMP=1 -default CONFIG_MAX_CPUS=2 - -## -## Build code to setup a generic IOAPIC -## -default CONFIG_IOAPIC=1 - -## -## Clean up the motherboard id strings -## -default MAINBOARD_PART_NUMBER="HDAMA" -default MAINBOARD_VENDOR="ARIMA" -default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f -default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016 - -### -### LinuxBIOS layout values -### - -## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. -default ROM_IMAGE_SIZE = 65536 - -## -## Use a small 8K stack -## -default STACK_SIZE=0x2000 - -## -## Use a small 32K heap -## -default HEAP_SIZE=0x8000 - -## -## Only use the option table in a normal image -## -default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE - ## ## Compute the location and size of where this firmware image ## (linuxBIOS plus bootloader) will live in the boot rom chip. @@ -157,203 +33,72 @@ default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE ) default XIP_ROM_SIZE=65536 default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) -## -## Set all of the defaults for an x86 architecture -## - -arch i386 end - -## -## Build the objects we have code for in this directory. -## - -driver mainboard.o -if HAVE_MP_TABLE object mptable.o end -if HAVE_PIRQ_TABLE object irq_tables.o end - -## -## Romcc output -## -makerule ./failover.E - depends "$(MAINBOARD)/failover.c" - action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E" -end - -makerule ./failover.inc - depends "./failover.E ./romcc" - action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E" -end - -makerule ./auto.E - depends "$(MAINBOARD)/auto.c option_table.h " - action "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E" -end -makerule ./auto.inc - depends "./auto.E ./romcc" - action "./romcc -mcpu=k8 -O2 ./auto.E > auto.inc" -end - -## -## Build our 16 bit and 32 bit linuxBIOS entry code -## -mainboardinit cpu/x86/16bit/entry16.inc -mainboardinit cpu/x86/32bit/entry32.inc -ldscript /cpu/x86/16bit/entry16.lds -ldscript /cpu/x86/32bit/entry32.lds - -## -## Build our reset vector (This is where linuxBIOS is entered) -## -if USE_FALLBACK_IMAGE - mainboardinit cpu/x86/16bit/reset16.inc - ldscript /cpu/x86/16bit/reset16.lds -else - mainboardinit cpu/x86/32bit/reset32.inc - ldscript /cpu/x86/32bit/reset32.lds -end - -### Should this be in the northbridge code? -mainboardinit arch/i386/lib/cpu_reset.inc - -## -## Include an id string (For safe flashing) -## -mainboardinit arch/i386/lib/id.inc -ldscript /arch/i386/lib/id.lds - -### -### This is the early phase of linuxBIOS startup -### Things are delicate and we test to see if we should -### failover to another image. -### -if USE_FALLBACK_IMAGE - ldscript /arch/i386/lib/failover.lds - mainboardinit ./failover.inc -end - -### -### O.k. We aren't just an intermediary anymore! -### - -## -## Setup RAM -## -mainboardinit cpu/x86/fpu/enable_fpu.inc -mainboardinit cpu/x86/mmx/enable_mmx.inc -mainboardinit cpu/x86/sse/enable_sse.inc -mainboardinit ./auto.inc -mainboardinit cpu/x86/sse/disable_sse.inc -mainboardinit cpu/x86/mmx/disable_mmx.inc - -## -## Include the secondary Configuration files -## -dir /pc80 -config chip.h - -northbridge amd/amdk8 "mc0" - pnp cf8.0 - northbridge amd/amdk8 "mc1" link 0 - pci 0:19.0 - pci 0:19.0 - pci 0:19.0 - pci 0:19.1 - pci 0:19.2 - pci 0:19.3 - end - pci 1:18.0 - southbridge amd/amd8131 "amd8131" link 1 - pci 0:0.0 - pci 0:0.1 - pci 0:1.0 - pci 0:1.1 - end - southbridge amd/amd8111 "amd8111" link 1 - pci 0:0.0 - pci 0:1.0 on - superio NSC/pc87360 link 1 - pnp 2e.0 off # Floppy - io 0x60 = 0x3f0 - irq 0x70 = 6 - drq 0x74 = 2 - pnp 2e.1 off # Parallel Port - io 0x60 = 0x378 - irq 0x70 = 7 - pnp 2e.2 off # Com 2 - io 0x60 = 0x2f8 - irq 0x70 = 3 - pnp 2e.3 on # Com 1 - io 0x60 = 0x3f8 - irq 0x70 = 4 - pnp 2e.4 off # SWC - pnp 2e.5 off # Mouse - pnp 2e.6 on # Keyboard - io 0x60 = 0x60 - io 0x62 = 0x64 - irq 0x70 = 1 - pnp 2e.7 off # GPIO - pnp 2e.8 off # ACB - pnp 2e.9 off # FSCM - pnp 2e.a off # WDT - end - pci 0:1.1 on - pci 0:1.2 on - pci 0:1.3 on # ACPI/SMBUS - chip drivers/generic/generic link 4 - #phillips pca9545 smbus mux - i2c 70 - # analog_devices adm1026 - chip drivers/generic/generic link 0 - i2c 2c - end - i2c 70 - i2c 70 - i2c 70 - end - chip drivers/generic/generic link 4 #dimm 0-0-0 - i2c 50 +# sample config for arima/hdama +chip northbridge/amd/amdk8 + print "HI MOM!\n" + device pnp cf8.0 on # cf8 config + print "HI MOM!\n" + device pci 18.0 on # northbridge + print "HI MOM!\n" + # devices on link 0, link 0 == LDT 0 + chip southbridge/amd/amd8131 + print "SOUTH\n" + # the on/off keyword is mandatory + device pci 0.0 on end + print "SOUTH2\n" + device pci 0.1 on end + print "SOUTH3\n" + device pci 1.0 on end + print "SOUTH4\n" + device pci 1.1 on end end - chip drivers/generic/generic link 4 #dimm 0-0-1 - i2c 51 - end - chip drivers/generic/generic link 4 #dimm 0-1-0 - i2c 52 - end - chip drivers/generic/generic link 4 #dimm 0-1-1 - i2c 53 - end - chip drivers/generic/generic link 4 #dimm 1-0-0 - i2c 54 + chip southbridge/amd/amd8111 + print "NEXT SOUTH\n" + # this "device pci 0.0" is the parent the next one + # PCI bridge + device pci 0.0 on + # this "device pci 0.0" is a child of the + # previous one + # devices behind the bridge + device pci 0.0 on end + device pci 0.1 on end + device pci 0.2 on end + # the device statement can span across multiple + # lines too + device pci 1.0 + off + end + end + device pci 1.0 on + chip superio/NSC/pc87360 + device pnp 2e.3 on + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + end + end + device pci 1.1 on end + device pci 1.2 off end + device pci 1.3 off end + device pci 1.5 on end + device pci 1.6 on end end - chip drivers/generic/generic link 4 #dimm 1-0-1 - i2c 55 - end - chip drivers/generic/generic link 4 #dimm 1-1-0 - i2c 56 - end - chip drivers/generic/generic link 4 #dimm 1-1-1 - i2c 57 - end - pci 0:1.5 off - pci 0:1.6 off - pci 1:0.0 on - pci 1:0.1 on - pci 1:0.2 on - pci 1:1.0 off - end - pci 1:18.0 - pci 1:18.0 - pci 1:18.1 - pci 1:18.2 - pci 1:18.3 -end - - -cpu amd/socket_940 "cpu0" link 1 - apic 0 -end - -cpu amd/socket_940 "cpu1" link 1 - apic 1 + end # device pci 18.0 + device pci 18.0 on + # some non-existence devices on link 1 + end + device pci 18.0 on + # some non-existence devices on link 2 + end + device pci 18.1 + # empty + end + device pci 18.2 + # empty + end + device pci 18.3 + # empty + end + end # device pnp end diff --git a/src/mainboard/arima/hdama/Options.lb b/src/mainboard/arima/hdama/Options.lb new file mode 100644 index 0000000000..f2c2dba2bb --- /dev/null +++ b/src/mainboard/arima/hdama/Options.lb @@ -0,0 +1,124 @@ +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses HARD_RESET_BUS +uses HARD_RESET_DEVICE +uses HARD_RESET_FUNCTION +uses IRQ_SLOT_COUNT +uses HAVE_OPTION_TABLE +uses CONFIG_MAX_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses FALLBACK_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_STREAM +uses CONFIG_ROM_STREAM_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses STACK_SIZE +uses HEAP_SIZE +uses USE_OPTION_TABLE +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +uses MAINBOARD +uses LINUXBIOS_EXTRA_VERSION +uses _RAMBASE + + +## ROM_SIZE is the size of boot ROM that this board will use. +default ROM_SIZE=524288 + +### +### Build options +### + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=1 + +default HARD_RESET_BUS=1 +default HARD_RESET_DEVICE=4 +default HARD_RESET_FUNCTION=0 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=1 +default IRQ_SLOT_COUNT=9 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=1 + +## +## Move the default LinuxBIOS cmos range off of AMD RTC registers +## +default LB_CKS_RANGE_START=49 +default LB_CKS_RANGE_END=122 +default LB_CKS_LOC=123 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## +default CONFIG_SMP=1 +default CONFIG_MAX_CPUS=2 + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Clean up the motherboard id strings +## +default MAINBOARD_PART_NUMBER="HDAMA" +default MAINBOARD_VENDOR="ARIMA" + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 65536 + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 16K heap +## +default HEAP_SIZE=0x4000 + +## +## Only use the option table in a normal image +## +default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE +default _RAMBASE=0x00004000 +end -- cgit v1.2.3