From bbbfd9d1906cb2d99385eae845a13a311f77ef78 Mon Sep 17 00:00:00 2001 From: Stefan Reinauer Date: Sat, 3 Dec 2005 23:48:17 +0000 Subject: smaller fixups here and there, allowing some motherboards to compile or to fail later than before. dos2unix'ed the xe7501devkit files, that might have caused some problems before. git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1 --- src/mainboard/Iwill/DK8X/cmos.layout | 11 +- src/mainboard/dell/s1850/chip.h | 4 +- src/mainboard/dell/s1850/mainboard.c | 4 +- src/mainboard/emulation/qemu-i386/Config.lb | 2 +- src/mainboard/emulation/qemu-i386/cmos.layout | 27 +- src/mainboard/intel/xe7501devkit/Config.lb | 440 +++++++++++------------ src/mainboard/intel/xe7501devkit/Options.lb | 473 +++++++++++++------------ src/mainboard/intel/xe7501devkit/acpi_tables.c | 242 +++++++------ src/mainboard/intel/xe7501devkit/auto.c | 184 +++++----- src/mainboard/intel/xe7501devkit/bus.h | 34 +- src/mainboard/intel/xe7501devkit/chip.h | 12 +- src/mainboard/intel/xe7501devkit/cmos.layout | 4 +- src/mainboard/intel/xe7501devkit/failover.c | 94 ++--- src/mainboard/intel/xe7501devkit/ioapic.h | 22 +- src/mainboard/intel/xe7501devkit/irq_tables.c | 148 ++++---- src/mainboard/intel/xe7501devkit/mainboard.c | 24 +- src/mainboard/intel/xe7501devkit/mptable.c | 360 +++++++++---------- src/mainboard/newisys/khepri/cmos.layout | 10 +- 18 files changed, 1044 insertions(+), 1051 deletions(-) (limited to 'src/mainboard') diff --git a/src/mainboard/Iwill/DK8X/cmos.layout b/src/mainboard/Iwill/DK8X/cmos.layout index 1ab6187288..0daae9221d 100644 --- a/src/mainboard/Iwill/DK8X/cmos.layout +++ b/src/mainboard/Iwill/DK8X/cmos.layout @@ -32,6 +32,7 @@ entries 395 1 e 1 hw_scrubber 396 1 e 1 interleave_chip_selects 397 2 e 8 max_mem_clock +399 1 e 2 dual_core 400 1 e 1 power_on_after_fail 412 4 e 6 debug_level 416 4 e 7 boot_first @@ -77,10 +78,10 @@ enumerations 7 9 Fallback_HDD 7 10 Fallback_Floppy #7 3 ROM -8 0 200Mhz -8 1 166Mhz -8 2 133Mhz -8 3 100Mhz +8 0 400Mhz +8 1 333Mhz +8 2 266Mhz +8 3 200Mhz 9 0 off 9 1 87.5% 9 2 75.0% @@ -93,3 +94,5 @@ enumerations checksums checksum 392 983 984 + + diff --git a/src/mainboard/dell/s1850/chip.h b/src/mainboard/dell/s1850/chip.h index b00189f049..75dcaf49c1 100644 --- a/src/mainboard/dell/s1850/chip.h +++ b/src/mainboard/dell/s1850/chip.h @@ -1,5 +1,5 @@ -struct chip_operations mainboard_dell_s2850_ops; +struct chip_operations mainboard_dell_s1850_ops; -struct mainboard_dell_s2850_config { +struct mainboard_dell_s1850_config { int nothing; }; diff --git a/src/mainboard/dell/s1850/mainboard.c b/src/mainboard/dell/s1850/mainboard.c index d1b419df6c..b82e1b968d 100644 --- a/src/mainboard/dell/s1850/mainboard.c +++ b/src/mainboard/dell/s1850/mainboard.c @@ -6,7 +6,7 @@ #include #include "chip.h" -struct chip_operations mainboard_dell_s2850_ops = { - CHIP_NAME("Dell S2850") +struct chip_operations mainboard_dell_s1850_ops = { + CHIP_NAME("Dell S1850") }; diff --git a/src/mainboard/emulation/qemu-i386/Config.lb b/src/mainboard/emulation/qemu-i386/Config.lb index 8b1e12010d..3b864a6e27 100644 --- a/src/mainboard/emulation/qemu-i386/Config.lb +++ b/src/mainboard/emulation/qemu-i386/Config.lb @@ -47,7 +47,7 @@ arch i386 end driver mainboard.o if HAVE_PIRQ_TABLE object irq_tables.o end -object reset.o +#object reset.o ## ## Romcc output diff --git a/src/mainboard/emulation/qemu-i386/cmos.layout b/src/mainboard/emulation/qemu-i386/cmos.layout index ea027282c4..5ba4c032c1 100644 --- a/src/mainboard/emulation/qemu-i386/cmos.layout +++ b/src/mainboard/emulation/qemu-i386/cmos.layout @@ -29,9 +29,6 @@ entries 386 1 e 1 ECC_memory 388 4 r 0 reboot_bits 392 3 e 5 baud_rate -395 1 e 1 hw_scrubber -396 1 e 1 interleave_chip_selects -397 2 e 8 max_mem_clock 400 1 e 1 power_on_after_fail 412 4 e 6 debug_level 416 4 e 7 boot_first @@ -39,15 +36,7 @@ entries 424 4 e 7 boot_third 428 4 h 0 boot_index 432 8 h 0 boot_countdown -440 4 e 9 slow_cpu -444 1 e 1 nmi -445 1 e 1 iommu -728 256 h 0 user_data -984 16 h 0 check_sum -# Reserve the extended AMD configuration registers -1000 24 r 0 reserved_memory - - +1008 16 h 0 check_sum enumerations @@ -77,21 +66,9 @@ enumerations 7 9 Fallback_HDD 7 10 Fallback_Floppy #7 3 ROM -8 0 200Mhz -8 1 166Mhz -8 2 133Mhz -8 3 100Mhz -9 0 off -9 1 87.5% -9 2 75.0% -9 3 62.5% -9 4 50.0% -9 5 37.5% -9 6 25.0% -9 7 12.5% checksums -checksum 392 983 984 +checksum 392 1007 1008 diff --git a/src/mainboard/intel/xe7501devkit/Config.lb b/src/mainboard/intel/xe7501devkit/Config.lb index 65ea45b566..2e1986369e 100644 --- a/src/mainboard/intel/xe7501devkit/Config.lb +++ b/src/mainboard/intel/xe7501devkit/Config.lb @@ -1,224 +1,224 @@ -################################################################## -## BEGIN BOILERPLATE - DO NOT EDIT -## -## Compute the location and size of where this firmware image -## (linuxBIOS plus payload) will live in the boot rom chip. -## -if USE_FALLBACK_IMAGE -# The fallback image uses FALLBACK_SIZE bytes at the end of the ROM - - default ROM_SECTION_SIZE = FALLBACK_SIZE - default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) - -else -# The normal image goes at the beginning of the LinuxBIOS ROM region -# and uses all the remaining space - - default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) - default ROM_SECTION_OFFSET = 0 -end - -## -## Compute where this copy of linuxBIOS will start in the boot rom -## -default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE ) - -## -## Compute a range of ROM that can cached to speed up linuxBIOS, -## execution speed. -## -## XIP_ROM_SIZE must be a power of 2. -## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE -default XIP_ROM_SIZE = 65536 -default XIP_ROM_BASE = ((( _ROMBASE + ROM_IMAGE_SIZE ) / XIP_ROM_SIZE ) * XIP_ROM_SIZE - XIP_ROM_SIZE ) - -## END BOILERPLATE -################################################################## - -arch i386 end - -## -## Build the objects we have code for in this directory. -## - -driver mainboard.o -if HAVE_MP_TABLE object mptable.o end -if HAVE_PIRQ_TABLE object irq_tables.o end -if HAVE_ACPI_TABLES object acpi_tables.o end -object reset.o - -# Include the VGA option ROM, but only if we're compiled to use it -if CONFIG_PCI_ROM_RUN - if CONFIG_CONSOLE_VGA - object vgarom.S - else - object no_vgarom.S - end -else - object no_vgarom.S -end - -## -## Romcc output -## -makerule ./failover.E - depends "$(MAINBOARD)/failover.c ./romcc" - action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" -end - -makerule ./failover.inc - depends "$(MAINBOARD)/failover.c ./romcc" - action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" -end - -makerule ./auto.E - depends "$(MAINBOARD)/auto.c option_table.h ./romcc" - action "./romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" -end -makerule ./auto.inc - depends "$(MAINBOARD)/auto.c option_table.h ./romcc" - action "./romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" -end - -## -## Build our 16 bit and 32 bit linuxBIOS entry code -## -mainboardinit cpu/x86/16bit/entry16.inc -mainboardinit cpu/x86/32bit/entry32.inc -ldscript /cpu/x86/16bit/entry16.lds -ldscript /cpu/x86/32bit/entry32.lds - -## -## Build our reset vector (This is where linuxBIOS is entered) -## -if HAVE_FALLBACK_BOOT - if USE_FALLBACK_IMAGE - mainboardinit cpu/x86/16bit/reset16.inc - ldscript /cpu/x86/16bit/reset16.lds - else - mainboardinit cpu/x86/32bit/reset32.inc - ldscript /cpu/x86/32bit/reset32.lds - end -else - mainboardinit cpu/x86/16bit/reset16.inc - ldscript /cpu/x86/16bit/reset16.lds -end - -### Should this be in the northbridge code? -mainboardinit arch/i386/lib/cpu_reset.inc - -## -## Include an id string (For safe flashing) -## -mainboardinit arch/i386/lib/id.inc -ldscript /arch/i386/lib/id.lds - -### -### This is the early phase of linuxBIOS startup -### Things are delicate and we test to see if we should -### failover to another image. -### -if USE_FALLBACK_IMAGE - ldscript /arch/i386/lib/failover.lds - mainboardinit ./failover.inc -end - -### -### O.k. We aren't just an intermediary anymore! -### - -## -## Setup RAM -## -mainboardinit cpu/x86/fpu/enable_fpu.inc -mainboardinit cpu/x86/mmx/enable_mmx.inc -mainboardinit cpu/x86/sse/enable_sse.inc -mainboardinit ./auto.inc -mainboardinit cpu/x86/sse/disable_sse.inc -mainboardinit cpu/x86/mmx/disable_mmx.inc - -## -## Include the secondary Configuration files -## -dir /pc80 - -if CONFIG_CHIP_NAME - config chip.h -end - -# based on sample config for tyan/s2735 -chip northbridge/intel/e7501 - device pci_domain 0 on - device pci 0.0 on end # Chipset host controller - device pci 0.1 on end # Host RASUM controller - device pci 2.0 on # Hub interface B - chip southbridge/intel/i82870 # P64H2 - device pci 1c.0 on end # IOAPIC - bus B - device pci 1d.0 on end # Hub to PCI-B bridge - device pci 1e.0 on end # IOAPIC - bus A - device pci 1f.0 on end # Hub to PCI-A bridge - end - end - device pci 3.0 off end # Hub interface C (82808AA connector - disable for now) - device pci 4.0 on # Hub interface D - chip southbridge/intel/i82870 # P64H2 - device pci 1c.0 on end # IOAPIC - bus B - device pci 1d.0 on end # Hub to PCI-B bridge - device pci 1e.0 on end # IOAPIC - bus A - device pci 1f.0 on end # Hub to PCI-A bridge - end - end - device pci 6.0 on end # E7501 Power management registers? (undocumented) - chip southbridge/intel/i82801ca - device pci 1d.0 off end # USB (might not work, Southbridge code needs looking at) - device pci 1d.1 off end # USB (not populated) - device pci 1d.2 off end # USB (not populated) - device pci 1e.0 on # Hub to PCI bridge +################################################################## +## BEGIN BOILERPLATE - DO NOT EDIT +## +## Compute the location and size of where this firmware image +## (linuxBIOS plus payload) will live in the boot rom chip. +## +if USE_FALLBACK_IMAGE +# The fallback image uses FALLBACK_SIZE bytes at the end of the ROM + + default ROM_SECTION_SIZE = FALLBACK_SIZE + default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) + +else +# The normal image goes at the beginning of the LinuxBIOS ROM region +# and uses all the remaining space + + default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) + default ROM_SECTION_OFFSET = 0 +end + +## +## Compute where this copy of linuxBIOS will start in the boot rom +## +default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE ) + +## +## Compute a range of ROM that can cached to speed up linuxBIOS, +## execution speed. +## +## XIP_ROM_SIZE must be a power of 2. +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE +default XIP_ROM_SIZE = 65536 +default XIP_ROM_BASE = ((( _ROMBASE + ROM_IMAGE_SIZE ) / XIP_ROM_SIZE ) * XIP_ROM_SIZE - XIP_ROM_SIZE ) + +## END BOILERPLATE +################################################################## + +arch i386 end + +## +## Build the objects we have code for in this directory. +## + +driver mainboard.o +if HAVE_MP_TABLE object mptable.o end +if HAVE_PIRQ_TABLE object irq_tables.o end +if HAVE_ACPI_TABLES object acpi_tables.o end +object reset.o + +# Include the VGA option ROM, but only if we're compiled to use it +if CONFIG_PCI_ROM_RUN + if CONFIG_CONSOLE_VGA + object vgarom.S + else + object no_vgarom.S + end +else + object no_vgarom.S +end + +## +## Romcc output +## +makerule ./failover.E + depends "$(MAINBOARD)/failover.c ./romcc" + action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" +end + +makerule ./failover.inc + depends "$(MAINBOARD)/failover.c ./romcc" + action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" +end + +makerule ./auto.E + depends "$(MAINBOARD)/auto.c option_table.h ./romcc" + action "./romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" +end +makerule ./auto.inc + depends "$(MAINBOARD)/auto.c option_table.h ./romcc" + action "./romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" +end + +## +## Build our 16 bit and 32 bit linuxBIOS entry code +## +mainboardinit cpu/x86/16bit/entry16.inc +mainboardinit cpu/x86/32bit/entry32.inc +ldscript /cpu/x86/16bit/entry16.lds +ldscript /cpu/x86/32bit/entry32.lds + +## +## Build our reset vector (This is where linuxBIOS is entered) +## +if HAVE_FALLBACK_BOOT + if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds + else + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds + end +else + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds +end + +### Should this be in the northbridge code? +mainboardinit arch/i386/lib/cpu_reset.inc + +## +## Include an id string (For safe flashing) +## +mainboardinit arch/i386/lib/id.inc +ldscript /arch/i386/lib/id.lds + +### +### This is the early phase of linuxBIOS startup +### Things are delicate and we test to see if we should +### failover to another image. +### +if USE_FALLBACK_IMAGE + ldscript /arch/i386/lib/failover.lds + mainboardinit ./failover.inc +end + +### +### O.k. We aren't just an intermediary anymore! +### + +## +## Setup RAM +## +mainboardinit cpu/x86/fpu/enable_fpu.inc +mainboardinit cpu/x86/mmx/enable_mmx.inc +mainboardinit cpu/x86/sse/enable_sse.inc +mainboardinit ./auto.inc +mainboardinit cpu/x86/sse/disable_sse.inc +mainboardinit cpu/x86/mmx/disable_mmx.inc + +## +## Include the secondary Configuration files +## +dir /pc80 + +if CONFIG_CHIP_NAME + config chip.h +end + +# based on sample config for tyan/s2735 +chip northbridge/intel/e7501 + device pci_domain 0 on + device pci 0.0 on end # Chipset host controller + device pci 0.1 on end # Host RASUM controller + device pci 2.0 on # Hub interface B + chip southbridge/intel/i82870 # P64H2 + device pci 1c.0 on end # IOAPIC - bus B + device pci 1d.0 on end # Hub to PCI-B bridge + device pci 1e.0 on end # IOAPIC - bus A + device pci 1f.0 on end # Hub to PCI-A bridge + end + end + device pci 3.0 off end # Hub interface C (82808AA connector - disable for now) + device pci 4.0 on # Hub interface D + chip southbridge/intel/i82870 # P64H2 + device pci 1c.0 on end # IOAPIC - bus B + device pci 1d.0 on end # Hub to PCI-B bridge + device pci 1e.0 on end # IOAPIC - bus A + device pci 1f.0 on end # Hub to PCI-A bridge + end + end + device pci 6.0 on end # E7501 Power management registers? (undocumented) + chip southbridge/intel/i82801ca + device pci 1d.0 off end # USB (might not work, Southbridge code needs looking at) + device pci 1d.1 off end # USB (not populated) + device pci 1d.2 off end # USB (not populated) + device pci 1e.0 on # Hub to PCI bridge chip drivers/pci/onboard # VGA ROM device pci 0.0 on end register "rom_address" = "_vgarom_start" - end + end end - device pci 1f.0 on # LPC bridge - chip superio/smsc/lpc47b272 - device pnp 2e.0 off # Floppy - io 0x60 = 0x3f0 - irq 0x70 = 6 - drq 0x74 = 2 - end - device pnp 2e.3 off # Parallel Port - io 0x60 = 0x378 - irq 0x70 = 7 - end - device pnp 2e.4 on # Com1 - io 0x60 = 0x3f8 - irq 0x70 = 4 - end - device pnp 2e.5 off # Com2 - io 0x60 = 0x2f8 - irq 0x70 = 3 - end - device pnp 2e.7 on # Keyboard - io 0x60 = 0x60 - io 0x62 = 0x64 - irq 0x70 = 1 # Keyboard interrupt - irq 0x72 = 12 # Mouse interrupt - end - device pnp 2e.a off end # ACPI - end - end - device pci 1f.1 on end # IDE - device pci 1f.3 on end # SMBus - device pci 1f.5 off end # AC97 Audio - device pci 1f.6 off end # AC97 Modem - end # SB - end # PCI_DOMAIN - device apic_cluster 0 on - chip cpu/intel/socket_mPGA604_533Mhz - device apic 0 on end - end - chip cpu/intel/socket_mPGA604_533Mhz - device apic 6 on end - end - end -end + device pci 1f.0 on # LPC bridge + chip superio/smsc/lpc47b272 + device pnp 2e.0 off # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + end + device pnp 2e.3 off # Parallel Port + io 0x60 = 0x378 + irq 0x70 = 7 + end + device pnp 2e.4 on # Com1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 2e.5 off # Com2 + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 2e.7 on # Keyboard + io 0x60 = 0x60 + io 0x62 = 0x64 + irq 0x70 = 1 # Keyboard interrupt + irq 0x72 = 12 # Mouse interrupt + end + device pnp 2e.a off end # ACPI + end + end + device pci 1f.1 on end # IDE + device pci 1f.3 on end # SMBus + device pci 1f.5 off end # AC97 Audio + device pci 1f.6 off end # AC97 Modem + end # SB + end # PCI_DOMAIN + device apic_cluster 0 on + chip cpu/intel/socket_mPGA604_533Mhz + device apic 0 on end + end + chip cpu/intel/socket_mPGA604_533Mhz + device apic 6 on end + end + end +end diff --git a/src/mainboard/intel/xe7501devkit/Options.lb b/src/mainboard/intel/xe7501devkit/Options.lb index b034ed6158..0b0588b2e6 100644 --- a/src/mainboard/intel/xe7501devkit/Options.lb +++ b/src/mainboard/intel/xe7501devkit/Options.lb @@ -1,234 +1,239 @@ -uses HAVE_MP_TABLE -uses HAVE_ACPI_TABLES -uses HAVE_PIRQ_TABLE -uses HAVE_FALLBACK_BOOT -uses HAVE_OPTION_TABLE -uses IRQ_SLOT_COUNT -uses CONFIG_MAX_CPUS -uses CONFIG_LOGICAL_CPUS -uses CONFIG_MAX_PHYSICAL_CPUS -uses CONFIG_IOAPIC -uses CONFIG_SMP -uses CONFIG_ROM_STREAM -uses STACK_SIZE -uses HEAP_SIZE -uses USE_OPTION_TABLE -uses LB_CKS_RANGE_START -uses LB_CKS_RANGE_END -uses LB_CKS_LOC -uses MAINBOARD_PART_NUMBER -uses MAINBOARD_VENDOR -uses MAINBOARD -uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID -uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID -uses _RAMBASE -uses TTYS0_BAUD -uses TTYS0_BASE -uses TTYS0_LCS -uses DEFAULT_CONSOLE_LOGLEVEL -uses MAXIMUM_CONSOLE_LOGLEVEL -uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL -uses CONFIG_CONSOLE_SERIAL8250 -uses CONFIG_UDELAY_TSC -uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 -uses HAVE_INIT_TIMER -uses CONFIG_GDB_STUB -uses CROSS_COMPILE -uses CC -uses HOSTCC -uses OBJCOPY -uses CONFIG_CHIP_NAME -uses CONFIG_CONSOLE_VGA -uses CONFIG_PCI_ROM_RUN -uses DEBUG -uses CPU_OPT -uses CONFIG_IDE - -## The default definitions are used for these -uses CONFIG_ROM_STREAM_START -uses PAYLOAD_SIZE - -## These are defined in target Config.lb, don't add here -uses USE_FALLBACK_IMAGE -uses ROM_SIZE -uses ROM_IMAGE_SIZE -uses FALLBACK_SIZE -uses LINUXBIOS_EXTRA_VERSION - -## These are defined in mainboard Config.lb, don't add here -uses ROM_SECTION_SIZE -uses ROM_SECTION_OFFSET -uses _ROMBASE -uses XIP_ROM_SIZE -uses XIP_ROM_BASE - -### -### Build options -### - -## -## Build code for the fallback boot? -## -default HAVE_FALLBACK_BOOT=0 - - -## Delay timer options -## -default CONFIG_UDELAY_TSC=1 -default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1 - -## -## Build code to export a programmable irq routing table -## -default HAVE_PIRQ_TABLE=1 -default IRQ_SLOT_COUNT=12 - -## -## Build code to export an x86 MP table -## Useful for specifying IRQ routing values -## -default HAVE_MP_TABLE=1 - -## Build code to export ACPI tables? -default HAVE_ACPI_TABLES=1 - -## -## Build code to export a CMOS option table? -## -default HAVE_OPTION_TABLE=0 - -## CMOS checksum definitions (units == bytes) -## These must match the checksum record in cmos.layout -default LB_CKS_RANGE_START=128 -default LB_CKS_RANGE_END=130 -default LB_CKS_LOC=131 - -## -## Build code for SMP support -## Only worry about 2 micro processors -## NOTE: CONFIG_MAX_CPUS is the number of LOGICAL CPUs, -## so if CONFIG_LOGICAL_CPUS is 1, CONFIG_MAX_CPUS should be 4. -## -default CONFIG_SMP=1 -default CONFIG_MAX_CPUS=2 -default CONFIG_LOGICAL_CPUS=0 -default CONFIG_MAX_PHYSICAL_CPUS=2 - -# VGA Console -# NOTE: to initialize VGA, need to copy the VGA option ROM from the factory BIOS -# to VGA.rom -default CONFIG_CONSOLE_VGA=0 -default CONFIG_PCI_ROM_RUN=0 - -## -## Build code to setup a generic IOAPIC -## -default CONFIG_IOAPIC=1 - -## -## Motherboard identification -## -default MAINBOARD_PART_NUMBER="EIDXE7501DEVKIT" -default MAINBOARD_VENDOR="Intel" -default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086 -default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2480 - -### -### LinuxBIOS layout values -### - -## -## Use a small 8K stack -## -default STACK_SIZE=0x2000 - -## -## Use a small 16K heap -## -default HEAP_SIZE=0x4000 - -## -## CMOS settings not currently supported due to conflicts with factory BIOS -## -default USE_OPTION_TABLE = 0 - -## -## LinuxBIOS C code runs at this location in RAM -## -default _RAMBASE=0x00004000 - -## -## Load the payload from the ROM -## -default CONFIG_ROM_STREAM = 1 - -### -### Defaults of options that you may want to override in the target config file -### - -## -## The default compiler -## -default CC="$(CROSS_COMPILE)gcc -m32" -default HOSTCC="gcc" - -## -## Disable the gdb stub by default -## -default CONFIG_GDB_STUB=0 - -## -## The Serial Console -## - -# To Enable the Serial Console -default CONFIG_CONSOLE_SERIAL8250=1 - -## Select the serial console baud rate -default TTYS0_BAUD=115200 -#default TTYS0_BAUD=57600 -#default TTYS0_BAUD=38400 -#default TTYS0_BAUD=19200 -#default TTYS0_BAUD=9600 -#default TTYS0_BAUD=4800 -#default TTYS0_BAUD=2400 -#default TTYS0_BAUD=1200 - -# Select the serial console base port -default TTYS0_BASE=0x3f8 - -# Select the serial protocol -# This defaults to 8 data bits, 1 stop bit, and no parity -default TTYS0_LCS=0x3 - -## -### Select the linuxBIOS loglevel -## -## EMERG 1 system is unusable -## ALERT 2 action must be taken immediately -## CRIT 3 critical conditions -## ERR 4 error conditions -## WARNING 5 warning conditions -## NOTICE 6 normal but significant condition -## INFO 7 informational -## DEBUG 8 debug-level messages -## SPEW 9 Way too many details - -## Request this level of debugging output -default DEFAULT_CONSOLE_LOGLEVEL=8 -## At a maximum only compile in this level of debugging -default MAXIMUM_CONSOLE_LOGLEVEL=8 - -## -## Select power on after power fail setting -default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" - -## Things we may not have -default CONFIG_IDE=1 - -default DEBUG=1 -default CPU_OPT="-g" -default CONFIG_CHIP_NAME=1 - -### End Options.lb -end +uses HAVE_MP_TABLE +uses HAVE_ACPI_TABLES +uses HAVE_PIRQ_TABLE +uses HAVE_FALLBACK_BOOT +uses HAVE_OPTION_TABLE +uses IRQ_SLOT_COUNT +uses CONFIG_MAX_CPUS +uses CONFIG_LOGICAL_CPUS +uses CONFIG_MAX_PHYSICAL_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses CONFIG_ROM_STREAM +uses STACK_SIZE +uses HEAP_SIZE +uses USE_OPTION_TABLE +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +uses MAINBOARD +uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID +uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID +uses _RAMBASE +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL +uses CONFIG_CONSOLE_SERIAL8250 +uses CONFIG_UDELAY_TSC +uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 +uses HAVE_INIT_TIMER +uses CONFIG_GDB_STUB +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY +uses CONFIG_CHIP_NAME +uses CONFIG_CONSOLE_VGA +uses CONFIG_PCI_ROM_RUN +uses DEBUG +uses CPU_OPT +uses CONFIG_IDE + +## The default definitions are used for these +uses CONFIG_ROM_STREAM_START +uses PAYLOAD_SIZE + +## These are defined in target Config.lb, don't add here +uses USE_FALLBACK_IMAGE +uses ROM_SIZE +uses ROM_IMAGE_SIZE +uses FALLBACK_SIZE +uses LINUXBIOS_EXTRA_VERSION + +## These are defined in mainboard Config.lb, don't add here +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE + +### +### Build options +### + +## +## ROM_SIZE is the size of boot ROM that this board will use. +## +default ROM_SIZE=2097152 + +## +## Build code for the fallback boot? +## +default HAVE_FALLBACK_BOOT=0 + + +## Delay timer options +## +default CONFIG_UDELAY_TSC=1 +default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=1 +default IRQ_SLOT_COUNT=12 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## Build code to export ACPI tables? +default HAVE_ACPI_TABLES=1 + +## +## Build code to export a CMOS option table? +## +default HAVE_OPTION_TABLE=0 + +## CMOS checksum definitions (units == bytes) +## These must match the checksum record in cmos.layout +default LB_CKS_RANGE_START=128 +default LB_CKS_RANGE_END=130 +default LB_CKS_LOC=131 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## NOTE: CONFIG_MAX_CPUS is the number of LOGICAL CPUs, +## so if CONFIG_LOGICAL_CPUS is 1, CONFIG_MAX_CPUS should be 4. +## +default CONFIG_SMP=1 +default CONFIG_MAX_CPUS=2 +default CONFIG_LOGICAL_CPUS=0 +default CONFIG_MAX_PHYSICAL_CPUS=2 + +# VGA Console +# NOTE: to initialize VGA, need to copy the VGA option ROM from the factory BIOS +# to VGA.rom +default CONFIG_CONSOLE_VGA=0 +default CONFIG_PCI_ROM_RUN=0 + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Motherboard identification +## +default MAINBOARD_PART_NUMBER="EIDXE7501DEVKIT" +default MAINBOARD_VENDOR="Intel" +default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086 +default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2480 + +### +### LinuxBIOS layout values +### + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 16K heap +## +default HEAP_SIZE=0x4000 + +## +## CMOS settings not currently supported due to conflicts with factory BIOS +## +default USE_OPTION_TABLE = 0 + +## +## LinuxBIOS C code runs at this location in RAM +## +default _RAMBASE=0x00004000 + +## +## Load the payload from the ROM +## +default CONFIG_ROM_STREAM = 1 + +### +### Defaults of options that you may want to override in the target config file +### + +## +## The default compiler +## +default CC="$(CROSS_COMPILE)gcc -m32" +default HOSTCC="gcc" + +## +## Disable the gdb stub by default +## +default CONFIG_GDB_STUB=0 + +## +## The Serial Console +## + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250=1 + +## Select the serial console baud rate +default TTYS0_BAUD=115200 +#default TTYS0_BAUD=57600 +#default TTYS0_BAUD=38400 +#default TTYS0_BAUD=19200 +#default TTYS0_BAUD=9600 +#default TTYS0_BAUD=4800 +#default TTYS0_BAUD=2400 +#default TTYS0_BAUD=1200 + +# Select the serial console base port +default TTYS0_BASE=0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS=0x3 + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL=8 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL=8 + +## +## Select power on after power fail setting +default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" + +## Things we may not have +default CONFIG_IDE=1 + +default DEBUG=1 +default CPU_OPT="-g" +default CONFIG_CHIP_NAME=1 + +### End Options.lb +end diff --git a/src/mainboard/intel/xe7501devkit/acpi_tables.c b/src/mainboard/intel/xe7501devkit/acpi_tables.c index 94cdb871ef..7d1261c57f 100644 --- a/src/mainboard/intel/xe7501devkit/acpi_tables.c +++ b/src/mainboard/intel/xe7501devkit/acpi_tables.c @@ -1,118 +1,124 @@ -/* - * Ported to Intel XE7501DEVKIT from Island Aruma - * written by Stefan Reinauer - * (C) 2005 Stefan Reinauer - * (C) 2005 Digital Design Corporation - */ - -#include -#include -#include -#include -#include -#include -#include "bus.h" -#include "ioapic.h" - -unsigned long acpi_dump_apics(unsigned long current) -{ - unsigned int irq_start = 0; - device_t dev = 0; - struct resource* res = NULL; - - - // SJM: Hard-code CPU LAPIC entries for now - // Use SourcePoint numbering of processors - current += acpi_create_madt_lapic((acpi_madt_lapic_t *)current, 0, 6); - current += acpi_create_madt_lapic((acpi_madt_lapic_t *)current, 1, 7); - current += acpi_create_madt_lapic((acpi_madt_lapic_t *)current, 2, 0); - current += acpi_create_madt_lapic((acpi_madt_lapic_t *)current, 3, 1); - - - // Southbridge IOAPIC - current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_ICH3, 0xfec00000, irq_start); - irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; - - // P64H2#2 Bus A IOAPIC - dev = dev_find_slot(PCI_BUS_E7501_HI_B, PCI_DEVFN(30, 0)); - if (!dev) - BUG(); // Config.lb error? - res = find_resource(dev, PCI_BASE_ADDRESS_0); - current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_P64H2_2_BUS_A, res->base, irq_start); - irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; - - // P64H2#2 Bus B IOAPIC - dev = dev_find_slot(PCI_BUS_E7501_HI_B, PCI_DEVFN(28, 0)); - if (!dev) - BUG(); // Config.lb error? - res = find_resource(dev, PCI_BASE_ADDRESS_0); - current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_P64H2_2_BUS_B, res->base, irq_start); - irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; - - - // P64H2#1 Bus A IOAPIC - dev = dev_find_slot(PCI_BUS_E7501_HI_D, PCI_DEVFN(30, 0)); - if (!dev) - BUG(); // Config.lb error? - res = find_resource(dev, PCI_BASE_ADDRESS_0); - current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_P64H2_1_BUS_A, res->base, irq_start); - irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; - - // P64H2#1 Bus B IOAPIC - dev = dev_find_slot(PCI_BUS_E7501_HI_D, PCI_DEVFN(28, 0)); - if (!dev) - BUG(); // Config.lb error? - res = find_resource(dev, PCI_BASE_ADDRESS_0); - current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_P64H2_1_BUS_B, res->base, irq_start); - irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; - - // Map ISA IRQ 0 to IRQ 2 - current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *)current, 1, 0, 2, 0); - - // IRQ9 differs from ISA standard - ours is active high, level-triggered - current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *)current, 0, 9, 9, 0xD); - - return current; -} - - -unsigned long write_acpi_tables(unsigned long start) -{ - unsigned long current; - acpi_rsdp_t *rsdp; - acpi_rsdt_t *rsdt; - acpi_madt_t *madt; - - /* Align ACPI tables to 16byte */ - start = ( start + 0x0f ) & -0x10; - current = start; - - printk_info("ACPI: Writing ACPI tables at %lx...\n", start); - - /* We need at least an RSDP and an RSDT Table */ - rsdp = (acpi_rsdp_t *) current; - current += sizeof(acpi_rsdp_t); - rsdt = (acpi_rsdt_t *) current; - current += sizeof(acpi_rsdt_t); - - /* clear all table memory */ - memset((void *)start, 0, current - start); - - acpi_write_rsdp(rsdp, rsdt); - acpi_write_rsdt(rsdt); - - /* - * We explicitly add these tables later on: - */ - /* QNX wants an MADT */ - printk_debug("ACPI: * MADT\n"); - - madt = (acpi_madt_t *) current; - acpi_create_madt(madt); - current+=madt->header.length; - acpi_add_table(rsdt,madt); - - printk_info("ACPI: done.\n"); - return current; -} - +/* + * Ported to Intel XE7501DEVKIT from Agami Aruma + * written by Stefan Reinauer + * (C) 2005 Stefan Reinauer + * (C) 2005 Digital Design Corporation + */ + +#include +#include +#include +#include +#include +#include +#include "bus.h" +#include "ioapic.h" + +unsigned long acpi_fill_srat(unsigned long current) +{ + // Not implemented + return 0; +} + +unsigned long acpi_fill_madt(unsigned long current) +{ + unsigned int irq_start = 0; + device_t dev = 0; + struct resource* res = NULL; + + + // SJM: Hard-code CPU LAPIC entries for now + // Use SourcePoint numbering of processors + current += acpi_create_madt_lapic((acpi_madt_lapic_t *)current, 0, 6); + current += acpi_create_madt_lapic((acpi_madt_lapic_t *)current, 1, 7); + current += acpi_create_madt_lapic((acpi_madt_lapic_t *)current, 2, 0); + current += acpi_create_madt_lapic((acpi_madt_lapic_t *)current, 3, 1); + + + // Southbridge IOAPIC + current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_ICH3, 0xfec00000, irq_start); + irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; + + // P64H2#2 Bus A IOAPIC + dev = dev_find_slot(PCI_BUS_E7501_HI_B, PCI_DEVFN(30, 0)); + if (!dev) + BUG(); // Config.lb error? + res = find_resource(dev, PCI_BASE_ADDRESS_0); + current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_P64H2_2_BUS_A, res->base, irq_start); + irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; + + // P64H2#2 Bus B IOAPIC + dev = dev_find_slot(PCI_BUS_E7501_HI_B, PCI_DEVFN(28, 0)); + if (!dev) + BUG(); // Config.lb error? + res = find_resource(dev, PCI_BASE_ADDRESS_0); + current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_P64H2_2_BUS_B, res->base, irq_start); + irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; + + + // P64H2#1 Bus A IOAPIC + dev = dev_find_slot(PCI_BUS_E7501_HI_D, PCI_DEVFN(30, 0)); + if (!dev) + BUG(); // Config.lb error? + res = find_resource(dev, PCI_BASE_ADDRESS_0); + current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_P64H2_1_BUS_A, res->base, irq_start); + irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; + + // P64H2#1 Bus B IOAPIC + dev = dev_find_slot(PCI_BUS_E7501_HI_D, PCI_DEVFN(28, 0)); + if (!dev) + BUG(); // Config.lb error? + res = find_resource(dev, PCI_BASE_ADDRESS_0); + current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *)current, IOAPIC_P64H2_1_BUS_B, res->base, irq_start); + irq_start += INTEL_IOAPIC_NUM_INTERRUPTS; + + // Map ISA IRQ 0 to IRQ 2 + current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *)current, 1, 0, 2, 0); + + // IRQ9 differs from ISA standard - ours is active high, level-triggered + current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *)current, 0, 9, 9, 0xD); + + return current; +} + + +unsigned long write_acpi_tables(unsigned long start) +{ + unsigned long current; + acpi_rsdp_t *rsdp; + acpi_rsdt_t *rsdt; + acpi_madt_t *madt; + + /* Align ACPI tables to 16byte */ + start = ( start + 0x0f ) & -0x10; + current = start; + + printk_info("ACPI: Writing ACPI tables at %lx...\n", start); + + /* We need at least an RSDP and an RSDT Table */ + rsdp = (acpi_rsdp_t *) current; + current += sizeof(acpi_rsdp_t); + rsdt = (acpi_rsdt_t *) current; + current += sizeof(acpi_rsdt_t); + + /* clear all table memory */ + memset((void *)start, 0, current - start); + + acpi_write_rsdp(rsdp, rsdt); + acpi_write_rsdt(rsdt); + + /* + * We explicitly add these tables later on: + */ + /* QNX wants an MADT */ + printk_debug("ACPI: * MADT\n"); + + madt = (acpi_madt_t *) current; + acpi_create_madt(madt); + current+=madt->header.length; + acpi_add_table(rsdt,madt); + + printk_info("ACPI: done.\n"); + return current; +} + diff --git a/src/mainboard/intel/xe7501devkit/auto.c b/src/mainboard/intel/xe7501devkit/auto.c index 8c635720af..1bd83a3187 100644 --- a/src/mainboard/intel/xe7501devkit/auto.c +++ b/src/mainboard/intel/xe7501devkit/auto.c @@ -1,92 +1,92 @@ -#define ASSEMBLY 1 - -#include -#include -#include -#include -#include -#include -#include -#include "option_table.h" -#include "pc80/mc146818rtc_early.c" -#include "pc80/serial.c" -#include "arch/i386/lib/console.c" -#include "ram/ramtest.c" -#include "southbridge/intel/i82801ca/i82801ca_early_smbus.c" -#include "northbridge/intel/e7501/raminit.h" -#include "cpu/x86/lapic/boot_cpu.c" -#include "northbridge/intel/e7501/debug.c" -#include "superio/smsc/lpc47b272/lpc47b272_early_serial.c" -#include "cpu/x86/mtrr/earlymtrr.c" -#include "cpu/x86/bist.h" - -#define SUPERIO_PORT 0x2e -#define SERIAL_DEV PNP_DEV(SUPERIO_PORT, LPC47B272_SP1) - -static void hard_reset(void) -{ - outb(0x0e, 0x0cf9); -} - -static inline void activate_spd_rom(const struct mem_controller *ctrl) -{ - /* nothing to do */ -} - -static inline int spd_read_byte(unsigned device, unsigned address) -{ - return smbus_read_byte(device, address); -} - -#include "northbridge/intel/e7501/raminit.c" -#include "northbridge/intel/e7501/reset_test.c" -#include "sdram/generic_sdram.c" - - -// This function MUST appear last (ROMCC limitation) -static void main(unsigned long bist) -{ - static const struct mem_controller memctrl[] = { - { - .d0 = PCI_DEV(0, 0, 0), - .d0f1 = PCI_DEV(0, 0, 1), - .channel0 = { (0xa<<3)|0, (0xa<<3)|1, (0xa<<3)|2, 0 }, - .channel1 = { (0xa<<3)|4, (0xa<<3)|5, (0xa<<3)|6, 0 }, - }, - }; - - if (bist == 0) - { - // Skip this if there was a built in self test failure - - early_mtrr_init(); - enable_lapic(); - } - - // Get the serial port running and print a welcome banner - - lpc47b272_enable_serial(SERIAL_DEV, TTYS0_BASE); - uart_init(); - console_init(); - - // Halt if there was a built in self test failure - report_bist_failure(bist); - -// print_pci_devices(); - - // If this is a warm boot, some initialization can be skipped - - if (!bios_reset_detected()) - { - enable_smbus(); -// dump_spd_registers(&memctrl[0]); -// dump_smbus_registers(); - -// memreset_setup(); No-op for this chipset - sdram_initialize(sizeof(memctrl)/sizeof(memctrl[0]), memctrl); - } - - // NOTE: ROMCC dies with an internal compiler error - // if the following line is removed. - print_debug("SDRAM is up.\r\n"); -} +#define ASSEMBLY 1 + +#include +#include +#include +#include +#include +#include +#include +#include "option_table.h" +#include "pc80/mc146818rtc_early.c" +#include "pc80/serial.c" +#include "arch/i386/lib/console.c" +#include "ram/ramtest.c" +#include "southbridge/intel/i82801ca/i82801ca_early_smbus.c" +#include "northbridge/intel/e7501/raminit.h" +#include "cpu/x86/lapic/boot_cpu.c" +#include "northbridge/intel/e7501/debug.c" +#include "superio/smsc/lpc47b272/lpc47b272_early_serial.c" +#include "cpu/x86/mtrr/earlymtrr.c" +#include "cpu/x86/bist.h" + +#define SUPERIO_PORT 0x2e +#define SERIAL_DEV PNP_DEV(SUPERIO_PORT, LPC47B272_SP1) + +static void hard_reset(void) +{ + outb(0x0e, 0x0cf9); +} + +static inline void activate_spd_rom(const struct mem_controller *ctrl) +{ + /* nothing to do */ +} + +static inline int spd_read_byte(unsigned device, unsigned address) +{ + return smbus_read_byte(device, address); +} + +#include "northbridge/intel/e7501/raminit.c" +#include "northbridge/intel/e7501/reset_test.c" +#include "sdram/generic_sdram.c" + + +// This function MUST appear last (ROMCC limitation) +static void main(unsigned long bist) +{ + static const struct mem_controller memctrl[] = { + { + .d0 = PCI_DEV(0, 0, 0), + .d0f1 = PCI_DEV(0, 0, 1), + .channel0 = { (0xa<<3)|0, (0xa<<3)|1, (0xa<<3)|2, 0 }, + .channel1 = { (0xa<<3)|4, (0xa<<3)|5, (0xa<<3)|6, 0 }, + }, + }; + + if (bist == 0) + { + // Skip this if there was a built in self test failure + + early_mtrr_init(); + enable_lapic(); + } + + // Get the serial port running and print a welcome banner + + lpc47b272_enable_serial(SERIAL_DEV, TTYS0_BASE); + uart_init(); + console_init(); + + // Halt if there was a built in self test failure + report_bist_failure(bist); + +// print_pci_devices(); + + // If this is a warm boot, some initialization can be skipped + + if (!bios_reset_detected()) + { + enable_smbus(); +// dump_spd_registers(&memctrl[0]); +// dump_smbus_registers(); + +// memreset_setup(); No-op for this chipset + sdram_initialize(sizeof(memctrl)/sizeof(memctrl[0]), memctrl); + } + + // NOTE: ROMCC dies with an internal compiler error + // if the following line is removed. + print_debug("SDRAM is up.\r\n"); +} diff --git a/src/mainboard/intel/xe7501devkit/bus.h b/src/mainboard/intel/xe7501devkit/bus.h index 0a99bb2808..84661ddb36 100644 --- a/src/mainboard/intel/xe7501devkit/bus.h +++ b/src/mainboard/intel/xe7501devkit/bus.h @@ -1,17 +1,17 @@ -#ifndef XE7501DEVKIT_BUS_H_INCLUDED -#define XE7501DEVKIT_BUS_H_INCLUDED - -// These were determined by seeing how LinuxBIOS enumerates the various -// PCI (and PCI-like) buses on the board. - -#define PCI_BUS_CHIPSET 0 -#define PCI_BUS_E7501_HI_B 1 // P64H2#2 -#define PCI_BUS_P64H2_2_B 2 // P64H2#2 bus B -#define PCI_BUS_P64H2_2_A 3 // P64H2#2 bus A -#define PCI_BUS_E7501_HI_D 4 // P64H2#1 -#define PCI_BUS_P64H2_1_B 5 // P64H2#1 bus B -#define PCI_BUS_P64H2_1_A 6 // P64H2#1 bus A -#define PCI_BUS_ICH3 7 // ICH3-S -#define SUPERIO_BUS 8 // (arbitrary but unique bus #) - -#endif // XE7501DEVKIT_BUS_H_INCLUDED +#ifndef XE7501DEVKIT_BUS_H_INCLUDED +#define XE7501DEVKIT_BUS_H_INCLUDED + +// These were determined by seeing how LinuxBIOS enumerates the various +// PCI (and PCI-like) buses on the board. + +#define PCI_BUS_CHIPSET 0 +#define PCI_BUS_E7501_HI_B 1 // P64H2#2 +#define PCI_BUS_P64H2_2_B 2 // P64H2#2 bus B +#define PCI_BUS_P64H2_2_A 3 // P64H2#2 bus A +#define PCI_BUS_E7501_HI_D 4 // P64H2#1 +#define PCI_BUS_P64H2_1_B 5 // P64H2#1 bus B +#define PCI_BUS_P64H2_1_A 6 // P64H2#1 bus A +#define PCI_BUS_ICH3 7 // ICH3-S +#define SUPERIO_BUS 8 // (arbitrary but unique bus #) + +#endif // XE7501DEVKIT_BUS_H_INCLUDED diff --git a/src/mainboard/intel/xe7501devkit/chip.h b/src/mainboard/intel/xe7501devkit/chip.h index b0885c1a54..12a9127ff2 100644 --- a/src/mainboard/intel/xe7501devkit/chip.h +++ b/src/mainboard/intel/xe7501devkit/chip.h @@ -1,6 +1,6 @@ -extern unsigned char _vgarom_start[]; - -extern struct chip_operations mainboard_intel_xe7501devkit_ops; - -struct mainboard_intel_xe7501devkit_config { -}; +extern unsigned char _vgarom_start[]; + +extern struct chip_operations mainboard_intel_xe7501devkit_ops; + +struct mainboard_intel_xe7501devkit_config { +}; diff --git a/src/mainboard/intel/xe7501devkit/cmos.layout b/src/mainboard/intel/xe7501devkit/cmos.layout index 1aa038d34d..57139c1cd5 100644 --- a/src/mainboard/intel/xe7501devkit/cmos.layout +++ b/src/mainboard/intel/xe7501devkit/cmos.layout @@ -7,8 +7,8 @@ entries 0 512 r 0 reserved_memory1 # We know nothing about the factory BIOS 512 512 r 0 reserved_memory2 # More factory BIOS -# Work in progress. -# This is where we would put the LB RTC_BOOT_BYTE options once the code +# Work in progress. +# This is where we would put the LB RTC_BOOT_BYTE options once the code # supports finding them there. #1024 1 e 4 boot_option #1025 1 e 4 last_boot diff --git a/src/mainboard/intel/xe7501devkit/failover.c b/src/mainboard/intel/xe7501devkit/failover.c index 68a1fec4eb..5ec12d67cd 100644 --- a/src/mainboard/intel/xe7501devkit/failover.c +++ b/src/mainboard/intel/xe7501devkit/failover.c @@ -1,47 +1,47 @@ -#define ASSEMBLY 1 -#include -#include -#include -#include -#include -#include -#include "pc80/mc146818rtc_early.c" -#include "southbridge/intel/i82801ca/cmos_failover.c" -#include "cpu/x86/lapic/boot_cpu.c" -#include "northbridge/intel/e7501/reset_test.c" - -static unsigned long main(unsigned long bist) -{ - /* Is this a deliberate reset by the bios */ - if (bios_reset_detected() && last_boot_normal()) { - goto normal_image; - } - /* This is the primary cpu how should I boot? */ - else { - - check_cmos_failed(); - - if (do_normal_boot()) { - goto normal_image; - } - else { - goto fallback_image; - } - } - normal_image: - asm volatile ("jmp __normal_image" - : /* outputs */ - : "a" (bist) /* inputs */ - : /* clobbers */ - ); -#if 0 - cpu_reset: - asm volatile ("jmp __cpu_reset" - : /* outputs */ - : "a"(bist) /* inputs */ - : /* clobbers */ - ); -#endif - fallback_image: - return bist; -} +#define ASSEMBLY 1 +#include +#include +#include +#include +#include +#include +#include "pc80/mc146818rtc_early.c" +#include "southbridge/intel/i82801ca/cmos_failover.c" +#include "cpu/x86/lapic/boot_cpu.c" +#include "northbridge/intel/e7501/reset_test.c" + +static unsigned long main(unsigned long bist) +{ + /* Is this a deliberate reset by the bios */ + if (bios_reset_detected() && last_boot_normal()) { + goto normal_image; + } + /* This is the primary cpu how should I boot? */ + else { + + check_cmos_failed(); + + if (do_normal_boot()) { + goto normal_image; + } + else { + goto fallback_image; + } + } + normal_image: + asm volatile ("jmp __normal_image" + : /* outputs */ + : "a" (bist) /* inputs */ + : /* clobbers */ + ); +#if 0 + cpu_reset: + asm volatile ("jmp __cpu_reset" + : /* outputs */ + : "a"(bist) /* inputs */ + : /* clobbers */ + ); +#endif + fallback_image: + return bist; +} diff --git a/src/mainboard/intel/xe7501devkit/ioapic.h b/src/mainboard/intel/xe7501devkit/ioapic.h index 6db3d949f6..642c04519f 100644 --- a/src/mainboard/intel/xe7501devkit/ioapic.h +++ b/src/mainboard/intel/xe7501devkit/ioapic.h @@ -1,11 +1,11 @@ -// IOAPIC addresses determined by LinuxBIOS enumeration. -// Someday add functions to get APIC IDs and versions from the chips themselves. - -#define IOAPIC_ICH3 2 -#define IOAPIC_P64H2_2_BUS_B 3 // IOAPIC 3 at 01:1c.0 MBAR = fe300000 DataAddr = fe300010 -#define IOAPIC_P64H2_2_BUS_A 4 // IOAPIC 4 at 01:1e.0 MBAR = fe301000 DataAddr = fe301010 -#define IOAPIC_P64H2_1_BUS_B 5 // IOAPIC 5 at 04:1c.0 MBAR = fe500000 DataAddr = fe500010 -#define IOAPIC_P64H2_1_BUS_A 8 // IOAPIC 8 at 04:1e.0 MBAR = fe501000 DataAddr = fe501010 - -#define P64H2_IOAPIC_VERSION 0x20 -#define INTEL_IOAPIC_NUM_INTERRUPTS 24 // Both ICH-3 and P64-H2 +// IOAPIC addresses determined by LinuxBIOS enumeration. +// Someday add functions to get APIC IDs and versions from the chips themselves. + +#define IOAPIC_ICH3 2 +#define IOAPIC_P64H2_2_BUS_B 3 // IOAPIC 3 at 01:1c.0 MBAR = fe300000 DataAddr = fe300010 +#define IOAPIC_P64H2_2_BUS_A 4 // IOAPIC 4 at 01:1e.0 MBAR = fe301000 DataAddr = fe301010 +#define IOAPIC_P64H2_1_BUS_B 5 // IOAPIC 5 at 04:1c.0 MBAR = fe500000 DataAddr = fe500010 +#define IOAPIC_P64H2_1_BUS_A 8 // IOAPIC 8 at 04:1e.0 MBAR = fe501000 DataAddr = fe501010 + +#define P64H2_IOAPIC_VERSION 0x20 +#define INTEL_IOAPIC_NUM_INTERRUPTS 24 // Both ICH-3 and P64-H2 diff --git a/src/mainboard/intel/xe7501devkit/irq_tables.c b/src/mainboard/intel/xe7501devkit/irq_tables.c index c30bf2daf2..0134f3be6d 100644 --- a/src/mainboard/intel/xe7501devkit/irq_tables.c +++ b/src/mainboard/intel/xe7501devkit/irq_tables.c @@ -1,74 +1,74 @@ -/* Run checkpir to verify any changes to this table... - Documentation at : http://www.microsoft.com/whdc/archive/pciirq.mspx -*/ - -#include -#include -#include -#include "bus.h" - -#define UNUSED_INTERRUPT {0, 0} -#define PIRQ_A 0x60 -#define PIRQ_B 0x61 -#define PIRQ_C 0x62 -#define PIRQ_D 0x63 -#define PIRQ_E 0x68 -#define PIRQ_F 0x69 -#define PIRQ_G 0x6A -#define PIRQ_H 0x6B - -const struct irq_routing_table intel_irq_routing_table = { - PIRQ_SIGNATURE, - PIRQ_VERSION, - 32 + 12*sizeof(struct irq_info), // Size of this struct in bytes - 0, // PCI bus number on which the interrupt router resides - PCI_DEVFN(31, 0), // PCI device/function number of the interrupt router - 0, // PCI-exclusive IRQ bitmap - PCI_VENDOR_ID_INTEL, // Vendor ID of compatible PCI interrupt router - PCI_DEVICE_ID_INTEL_82801CA_LPC, // Device ID of compatible PCI interrupt router - 0, // Additional miniport information - { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, // Reserved, must be zero - 0xB1, // Checksum of the entire structure (causes 8-bit sum == 0) - { - // NOTE: For 82801, a nonzero link value is a pointer to a PIRQ[n]_ROUT register in PCI configuration space - // This was determined from linux-2.6.11/arch/i386/pci/irq.c - // bitmap of 0xdcf8 == routable to IRQ3-IRQ7, IRQ10-IRQ12, or IRQ14-IRQ15 - // ICH-3 doesn't allow SERIRQ or PCI message to generate IRQ0, IRQ2, IRQ8, or IRQ13 - // Not sure why IRQ9 isn't routable (inherited from Tyan S2735) - - // INTA# INTB# INTC# INTD# - // bus, device # {link , bitmap}, {link , bitmap}, {link , bitmap}, {link , bitmap}, slot, rfu - - {PCI_BUS_CHIPSET, PCI_DEVFN(31, 0), {{PIRQ_C, 0xdcf8}, {PIRQ_B, 0xdcf8}, UNUSED_INTERRUPT, UNUSED_INTERRUPT}, 0, 0}, // IDE / SMBus - {PCI_BUS_CHIPSET, PCI_DEVFN(29, 0), {{PIRQ_A, 0xdcf8}, {PIRQ_D, 0xdcf8}, {PIRQ_C, 0xdcf8}, UNUSED_INTERRUPT}, 0, 0}, // USB 1.1 - - // P64H2#2 Bus A - {PCI_BUS_P64H2_2_A, PCI_DEVFN(1, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, UNUSED_INTERRUPT, UNUSED_INTERRUPT}, 0, 0}, // SCSI - // NOTE: Hotplug disabled on this bus - - // P64H2#2 Bus B - {PCI_BUS_P64H2_2_B, PCI_DEVFN(1, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 23, 0}, // Slot 2A (J23) - {PCI_BUS_P64H2_2_B, PCI_DEVFN(2, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 24, 0}, // Slot 2B (J24) - {PCI_BUS_P64H2_2_B, PCI_DEVFN(3, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 25, 0}, // Slot 2C (J25) - {PCI_BUS_P64H2_2_B, PCI_DEVFN(4, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 12, 0}, // Slot 2D (J12) - // NOTE: Hotplug disabled on this bus - - // P64H2#1 Bus A - {PCI_BUS_P64H2_1_A, PCI_DEVFN(1, 0), {{PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}}, 20, 0}, // Slot 1A (J20) - // NOTE: Hotplug disabled on this bus - - // P64H2#1 Bus B - {PCI_BUS_P64H2_1_B, PCI_DEVFN(1, 0), {{PIRQ_A, 0xdcf8}, UNUSED_INTERRUPT, UNUSED_INTERRUPT, UNUSED_INTERRUPT}, 0, 0}, // GB Ethernet - {PCI_BUS_P64H2_1_B, PCI_DEVFN(2, 0), {{PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}}, 21, 0}, // Slot 1B (J21) - // NOTE: Hotplug disabled on this bus - - // ICH-3 PCI bus - {PCI_BUS_ICH3, PCI_DEVFN(0, 0), {{PIRQ_A, 0xdcf8}, UNUSED_INTERRUPT, UNUSED_INTERRUPT, UNUSED_INTERRUPT}, 0, 0}, // Video - {PCI_BUS_ICH3, PCI_DEVFN(2, 0), {{PIRQ_C, 0xdcf8}, {PIRQ_D, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 11, 0}, // Debug slot (J11) - } -}; - -unsigned long write_pirq_routing_table(unsigned long addr) -{ - return copy_pirq_routing_table(addr); -} +/* Run checkpir to verify any changes to this table... + Documentation at : http://www.microsoft.com/whdc/archive/pciirq.mspx +*/ + +#include +#include +#include +#include "bus.h" + +#define UNUSED_INTERRUPT {0, 0} +#define PIRQ_A 0x60 +#define PIRQ_B 0x61 +#define PIRQ_C 0x62 +#define PIRQ_D 0x63 +#define PIRQ_E 0x68 +#define PIRQ_F 0x69 +#define PIRQ_G 0x6A +#define PIRQ_H 0x6B + +const struct irq_routing_table intel_irq_routing_table = { + PIRQ_SIGNATURE, + PIRQ_VERSION, + 32 + 12*sizeof(struct irq_info), // Size of this struct in bytes + 0, // PCI bus number on which the interrupt router resides + PCI_DEVFN(31, 0), // PCI device/function number of the interrupt router + 0, // PCI-exclusive IRQ bitmap + PCI_VENDOR_ID_INTEL, // Vendor ID of compatible PCI interrupt router + PCI_DEVICE_ID_INTEL_82801CA_LPC, // Device ID of compatible PCI interrupt router + 0, // Additional miniport information + { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, // Reserved, must be zero + 0xB1, // Checksum of the entire structure (causes 8-bit sum == 0) + { + // NOTE: For 82801, a nonzero link value is a pointer to a PIRQ[n]_ROUT register in PCI configuration space + // This was determined from linux-2.6.11/arch/i386/pci/irq.c + // bitmap of 0xdcf8 == routable to IRQ3-IRQ7, IRQ10-IRQ12, or IRQ14-IRQ15 + // ICH-3 doesn't allow SERIRQ or PCI message to generate IRQ0, IRQ2, IRQ8, or IRQ13 + // Not sure why IRQ9 isn't routable (inherited from Tyan S2735) + + // INTA# INTB# INTC# INTD# + // bus, device # {link , bitmap}, {link , bitmap}, {link , bitmap}, {link , bitmap}, slot, rfu + + {PCI_BUS_CHIPSET, PCI_DEVFN(31, 0), {{PIRQ_C, 0xdcf8}, {PIRQ_B, 0xdcf8}, UNUSED_INTERRUPT, UNUSED_INTERRUPT}, 0, 0}, // IDE / SMBus + {PCI_BUS_CHIPSET, PCI_DEVFN(29, 0), {{PIRQ_A, 0xdcf8}, {PIRQ_D, 0xdcf8}, {PIRQ_C, 0xdcf8}, UNUSED_INTERRUPT}, 0, 0}, // USB 1.1 + + // P64H2#2 Bus A + {PCI_BUS_P64H2_2_A, PCI_DEVFN(1, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, UNUSED_INTERRUPT, UNUSED_INTERRUPT}, 0, 0}, // SCSI + // NOTE: Hotplug disabled on this bus + + // P64H2#2 Bus B + {PCI_BUS_P64H2_2_B, PCI_DEVFN(1, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 23, 0}, // Slot 2A (J23) + {PCI_BUS_P64H2_2_B, PCI_DEVFN(2, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 24, 0}, // Slot 2B (J24) + {PCI_BUS_P64H2_2_B, PCI_DEVFN(3, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 25, 0}, // Slot 2C (J25) + {PCI_BUS_P64H2_2_B, PCI_DEVFN(4, 0), {{PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 12, 0}, // Slot 2D (J12) + // NOTE: Hotplug disabled on this bus + + // P64H2#1 Bus A + {PCI_BUS_P64H2_1_A, PCI_DEVFN(1, 0), {{PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}}, 20, 0}, // Slot 1A (J20) + // NOTE: Hotplug disabled on this bus + + // P64H2#1 Bus B + {PCI_BUS_P64H2_1_B, PCI_DEVFN(1, 0), {{PIRQ_A, 0xdcf8}, UNUSED_INTERRUPT, UNUSED_INTERRUPT, UNUSED_INTERRUPT}, 0, 0}, // GB Ethernet + {PCI_BUS_P64H2_1_B, PCI_DEVFN(2, 0), {{PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_A, 0xdcf8}}, 21, 0}, // Slot 1B (J21) + // NOTE: Hotplug disabled on this bus + + // ICH-3 PCI bus + {PCI_BUS_ICH3, PCI_DEVFN(0, 0), {{PIRQ_A, 0xdcf8}, UNUSED_INTERRUPT, UNUSED_INTERRUPT, UNUSED_INTERRUPT}, 0, 0}, // Video + {PCI_BUS_ICH3, PCI_DEVFN(2, 0), {{PIRQ_C, 0xdcf8}, {PIRQ_D, 0xdcf8}, {PIRQ_A, 0xdcf8}, {PIRQ_B, 0xdcf8}}, 11, 0}, // Debug slot (J11) + } +}; + +unsigned long write_pirq_routing_table(unsigned long addr) +{ + return copy_pirq_routing_table(addr); +} diff --git a/src/mainboard/intel/xe7501devkit/mainboard.c b/src/mainboard/intel/xe7501devkit/mainboard.c index 38639b9d39..158b0183e2 100644 --- a/src/mainboard/intel/xe7501devkit/mainboard.c +++ b/src/mainboard/intel/xe7501devkit/mainboard.c @@ -1,12 +1,12 @@ -#include -#include -#include -#include -#include -#include "chip.h" - -#if CONFIG_CHIP_NAME == 1 -struct chip_operations mainboard_intel_xe7501devkit_ops = { - CHIP_NAME("Intel Xeon E7501 DevKit mainboard") -}; -#endif +#include +#include +#include +#include +#include +#include "chip.h" + +#if CONFIG_CHIP_NAME == 1 +struct chip_operations mainboard_intel_xe7501devkit_ops = { + CHIP_NAME("Intel Xeon E7501 DevKit mainboard") +}; +#endif diff --git a/src/mainboard/intel/xe7501devkit/mptable.c b/src/mainboard/intel/xe7501devkit/mptable.c index 7dae29c450..0da0676d35 100644 --- a/src/mainboard/intel/xe7501devkit/mptable.c +++ b/src/mainboard/intel/xe7501devkit/mptable.c @@ -1,180 +1,180 @@ -#include -#include -#include -#include -#include -#include -#include "bus.h" -#include "ioapic.h" - -// Generate MP-table IRQ numbers for PCI devices. -#define INT_A 0 -#define INT_B 1 -#define INT_C 2 -#define INT_D 3 -#define PCI_IRQ(dev, intLine) (((dev)<<2) | intLine) - - -void xe7501devkit_register_buses(struct mp_config_table *mc) -{ - // Bus ID, Bus Type - smp_write_bus(mc, PCI_BUS_CHIPSET, BUSTYPE_PCI); - smp_write_bus(mc, PCI_BUS_E7501_HI_B, BUSTYPE_PCI); - smp_write_bus(mc, PCI_BUS_P64H2_2_B, BUSTYPE_PCI); - smp_write_bus(mc, PCI_BUS_P64H2_2_A, BUSTYPE_PCI); - smp_write_bus(mc, PCI_BUS_E7501_HI_D, BUSTYPE_PCI); - smp_write_bus(mc, PCI_BUS_P64H2_1_B, BUSTYPE_PCI); - smp_write_bus(mc, PCI_BUS_P64H2_1_A, BUSTYPE_PCI); - smp_write_bus(mc, PCI_BUS_ICH3, BUSTYPE_PCI); - smp_write_bus(mc, SUPERIO_BUS, BUSTYPE_ISA); -} - -void xe7501devkit_register_ioapics(struct mp_config_table *mc) -{ - device_t dev; - struct resource *res; - - // TODO: Gack. This is REALLY ugly. - - // Southbridge IOAPIC - smp_write_ioapic(mc, IOAPIC_ICH3, 0x20, 0xfec00000); // APIC ID, Version, Address - - // P64H2#2 Bus A IOAPIC - dev = dev_find_slot(PCI_BUS_E7501_HI_B, PCI_DEVFN(30, 0)); - if (!dev) - BUG(); // Config.lb error? - res = find_resource(dev, PCI_BASE_ADDRESS_0); - smp_write_ioapic(mc, IOAPIC_P64H2_2_BUS_A, P64H2_IOAPIC_VERSION, res->base); - - // P64H2#2 Bus B IOAPIC - dev = dev_find_slot(PCI_BUS_E7501_HI_B, PCI_DEVFN(28, 0)); - if (!dev) - BUG(); // Config.lb error? - res = find_resource(dev, PCI_BASE_ADDRESS_0); - smp_write_ioapic(mc, IOAPIC_P64H2_2_BUS_B, P64H2_IOAPIC_VERSION, res->base); - - - // P64H2#1 Bus A IOAPIC - dev = dev_find_slot(PCI_BUS_E7501_HI_D, PCI_DEVFN(30, 0)); - if (!dev) - BUG(); // Config.lb error? - res = find_resource(dev, PCI_BASE_ADDRESS_0); - smp_write_ioapic(mc, IOAPIC_P64H2_1_BUS_A, P64H2_IOAPIC_VERSION, res->base); - - // P64H2#1 Bus B IOAPIC - dev = dev_find_slot(PCI_BUS_E7501_HI_D, PCI_DEVFN(28, 0)); - if (!dev) - BUG(); // Config.lb error? - res = find_resource(dev, PCI_BASE_ADDRESS_0); - smp_write_ioapic(mc, IOAPIC_P64H2_1_BUS_B, P64H2_IOAPIC_VERSION, res->base); -} - -void xe7501devkit_register_interrupts(struct mp_config_table *mc) -{ - // Chipset PCI bus - // Type Trigger | Polarity Bus ID IRQ APIC ID PIN# - smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, PCI_BUS_CHIPSET, 0, MP_APIC_ALL, 0); - smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, PCI_BUS_CHIPSET, 0, MP_APIC_ALL, 1); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(29, INT_A), IOAPIC_ICH3, 16); // USB 1.1 Controller #1 - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(31, INT_B), IOAPIC_ICH3, 17); // SMBus - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(29, INT_C), IOAPIC_ICH3, 18); // USB 1.1 Controller #3 - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(31, INT_C), IOAPIC_ICH3, 18); // IDE - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(29, INT_D), IOAPIC_ICH3, 19); // USB 1.1 Controller #2 - - // P64H2#2 Bus B - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(1, INT_A), IOAPIC_P64H2_2_BUS_B, 0); // Slot 2A (J23) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(1, INT_B), IOAPIC_P64H2_2_BUS_B, 1); // Slot 2A (J23) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(1, INT_C), IOAPIC_P64H2_2_BUS_B, 2); // Slot 2A (J23) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(1, INT_D), IOAPIC_P64H2_2_BUS_B, 3); // Slot 2A (J23) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(2, INT_A), IOAPIC_P64H2_2_BUS_B, 4); // Slot 2B (J24) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(2, INT_B), IOAPIC_P64H2_2_BUS_B, 5); // Slot 2B (J24) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(2, INT_C), IOAPIC_P64H2_2_BUS_B, 6); // Slot 2B (J24) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(2, INT_D), IOAPIC_P64H2_2_BUS_B, 7); // Slot 2B (J24) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(3, INT_A), IOAPIC_P64H2_2_BUS_B, 8); // Slot 2C (J25) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(3, INT_B), IOAPIC_P64H2_2_BUS_B, 9); // Slot 2C (J25) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(3, INT_C), IOAPIC_P64H2_2_BUS_B, 10); // Slot 2C (J25) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(3, INT_D), IOAPIC_P64H2_2_BUS_B, 11); // Slot 2C (J25) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(4, INT_A), IOAPIC_P64H2_2_BUS_B, 12); // Slot 2D (J12) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(4, INT_B), IOAPIC_P64H2_2_BUS_B, 13); // Slot 2D (J12) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(4, INT_C), IOAPIC_P64H2_2_BUS_B, 14); // Slot 2D (J12) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(4, INT_D), IOAPIC_P64H2_2_BUS_B, 15); // Slot 2D (J12) - - // P64H2#2 Bus A - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_A, PCI_IRQ(1, INT_A), IOAPIC_P64H2_2_BUS_A, 0); // SCSI - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_A, PCI_IRQ(1, INT_B), IOAPIC_P64H2_2_BUS_A, 1); // SCSI - - // P64H2#1 Bus B - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(1, INT_A), IOAPIC_P64H2_1_BUS_B, 0); // GB Ethernet - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(2, INT_A), IOAPIC_P64H2_1_BUS_B, 4); // Slot 1B (J21) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(2, INT_B), IOAPIC_P64H2_1_BUS_B, 5); // Slot 1B (J21) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(2, INT_C), IOAPIC_P64H2_1_BUS_B, 6); // Slot 1B (J21) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(2, INT_D), IOAPIC_P64H2_1_BUS_B, 7); // Slot 1B (J21) - - // P64H2#1 Bus A - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_A, PCI_IRQ(1, INT_A), IOAPIC_P64H2_1_BUS_A, 0); // Slot 1A (J20) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_A, PCI_IRQ(1, INT_B), IOAPIC_P64H2_1_BUS_A, 1); // Slot 1A (J20) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_A, PCI_IRQ(1, INT_C), IOAPIC_P64H2_1_BUS_A, 2); // Slot 1A (J20) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_A, PCI_IRQ(1, INT_D), IOAPIC_P64H2_1_BUS_A, 3); // Slot 1A (J20) - - // ICH-3 - - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(0, INT_A), IOAPIC_ICH3, 16); // Video - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(2, INT_A), IOAPIC_ICH3, 18); // Debug slot (J11) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(2, INT_B), IOAPIC_ICH3, 19); // Debug slot (J11) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(2, INT_C), IOAPIC_ICH3, 16); // Debug slot (J11) - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(2, INT_D), IOAPIC_ICH3, 17); // Debug slot (J11) - - // TODO: Not sure how to handle BT_INTR# signals from the P64H2s. Do we even need to, in APIC mode? - - // Super I/O (ISA interrupts) - smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 0, IOAPIC_ICH3, 0); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 1, IOAPIC_ICH3, 1); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 0, IOAPIC_ICH3, 2); - - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 3, IOAPIC_ICH3, 3); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 4, IOAPIC_ICH3, 4); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 6, IOAPIC_ICH3, 6); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 8, IOAPIC_ICH3, 8); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 9, IOAPIC_ICH3, 9); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 12, IOAPIC_ICH3, 12); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 13, IOAPIC_ICH3, 13); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 14, IOAPIC_ICH3, 14); - smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 15, IOAPIC_ICH3, 15); -} - -void* smp_write_config_table(void* v) -{ - static const char sig[4] = MPC_SIGNATURE; - static const char oem[8] = "INTEL "; - static const char productid[12] = "XE7501DEVKIT"; - struct mp_config_table *mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); - memset(mc, 0, sizeof(*mc)); - - memcpy(mc->mpc_signature, sig, sizeof(sig)); - memcpy(mc->mpc_oem, oem, sizeof(oem)); - memcpy(mc->mpc_productid, productid, sizeof(productid)); - - mc->mpc_length = sizeof(*mc); // initially just the header - mc->mpc_spec = 0x04; // Multiprocessing Spec V1.4 - mc->mpc_lapic = LAPIC_ADDR; - - smp_write_processors(mc); - - xe7501devkit_register_buses(mc); - xe7501devkit_register_ioapics(mc); - xe7501devkit_register_interrupts(mc); - - /* Compute the checksums */ - mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length); - mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length); - printk_debug("Wrote the mp table end at: %p - %p\n", mc, smp_next_mpe_entry(mc)); - - return smp_next_mpe_entry(mc); -} - -unsigned long write_smp_table(unsigned long addr) -{ - void *v; - v = smp_write_floating_table(addr); - return (unsigned long)smp_write_config_table(v); -} +#include +#include +#include +#include +#include +#include +#include "bus.h" +#include "ioapic.h" + +// Generate MP-table IRQ numbers for PCI devices. +#define INT_A 0 +#define INT_B 1 +#define INT_C 2 +#define INT_D 3 +#define PCI_IRQ(dev, intLine) (((dev)<<2) | intLine) + + +void xe7501devkit_register_buses(struct mp_config_table *mc) +{ + // Bus ID, Bus Type + smp_write_bus(mc, PCI_BUS_CHIPSET, BUSTYPE_PCI); + smp_write_bus(mc, PCI_BUS_E7501_HI_B, BUSTYPE_PCI); + smp_write_bus(mc, PCI_BUS_P64H2_2_B, BUSTYPE_PCI); + smp_write_bus(mc, PCI_BUS_P64H2_2_A, BUSTYPE_PCI); + smp_write_bus(mc, PCI_BUS_E7501_HI_D, BUSTYPE_PCI); + smp_write_bus(mc, PCI_BUS_P64H2_1_B, BUSTYPE_PCI); + smp_write_bus(mc, PCI_BUS_P64H2_1_A, BUSTYPE_PCI); + smp_write_bus(mc, PCI_BUS_ICH3, BUSTYPE_PCI); + smp_write_bus(mc, SUPERIO_BUS, BUSTYPE_ISA); +} + +void xe7501devkit_register_ioapics(struct mp_config_table *mc) +{ + device_t dev; + struct resource *res; + + // TODO: Gack. This is REALLY ugly. + + // Southbridge IOAPIC + smp_write_ioapic(mc, IOAPIC_ICH3, 0x20, 0xfec00000); // APIC ID, Version, Address + + // P64H2#2 Bus A IOAPIC + dev = dev_find_slot(PCI_BUS_E7501_HI_B, PCI_DEVFN(30, 0)); + if (!dev) + BUG(); // Config.lb error? + res = find_resource(dev, PCI_BASE_ADDRESS_0); + smp_write_ioapic(mc, IOAPIC_P64H2_2_BUS_A, P64H2_IOAPIC_VERSION, res->base); + + // P64H2#2 Bus B IOAPIC + dev = dev_find_slot(PCI_BUS_E7501_HI_B, PCI_DEVFN(28, 0)); + if (!dev) + BUG(); // Config.lb error? + res = find_resource(dev, PCI_BASE_ADDRESS_0); + smp_write_ioapic(mc, IOAPIC_P64H2_2_BUS_B, P64H2_IOAPIC_VERSION, res->base); + + + // P64H2#1 Bus A IOAPIC + dev = dev_find_slot(PCI_BUS_E7501_HI_D, PCI_DEVFN(30, 0)); + if (!dev) + BUG(); // Config.lb error? + res = find_resource(dev, PCI_BASE_ADDRESS_0); + smp_write_ioapic(mc, IOAPIC_P64H2_1_BUS_A, P64H2_IOAPIC_VERSION, res->base); + + // P64H2#1 Bus B IOAPIC + dev = dev_find_slot(PCI_BUS_E7501_HI_D, PCI_DEVFN(28, 0)); + if (!dev) + BUG(); // Config.lb error? + res = find_resource(dev, PCI_BASE_ADDRESS_0); + smp_write_ioapic(mc, IOAPIC_P64H2_1_BUS_B, P64H2_IOAPIC_VERSION, res->base); +} + +void xe7501devkit_register_interrupts(struct mp_config_table *mc) +{ + // Chipset PCI bus + // Type Trigger | Polarity Bus ID IRQ APIC ID PIN# + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, PCI_BUS_CHIPSET, 0, MP_APIC_ALL, 0); + smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, PCI_BUS_CHIPSET, 0, MP_APIC_ALL, 1); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(29, INT_A), IOAPIC_ICH3, 16); // USB 1.1 Controller #1 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(31, INT_B), IOAPIC_ICH3, 17); // SMBus + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(29, INT_C), IOAPIC_ICH3, 18); // USB 1.1 Controller #3 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(31, INT_C), IOAPIC_ICH3, 18); // IDE + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_CHIPSET, PCI_IRQ(29, INT_D), IOAPIC_ICH3, 19); // USB 1.1 Controller #2 + + // P64H2#2 Bus B + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(1, INT_A), IOAPIC_P64H2_2_BUS_B, 0); // Slot 2A (J23) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(1, INT_B), IOAPIC_P64H2_2_BUS_B, 1); // Slot 2A (J23) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(1, INT_C), IOAPIC_P64H2_2_BUS_B, 2); // Slot 2A (J23) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(1, INT_D), IOAPIC_P64H2_2_BUS_B, 3); // Slot 2A (J23) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(2, INT_A), IOAPIC_P64H2_2_BUS_B, 4); // Slot 2B (J24) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(2, INT_B), IOAPIC_P64H2_2_BUS_B, 5); // Slot 2B (J24) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(2, INT_C), IOAPIC_P64H2_2_BUS_B, 6); // Slot 2B (J24) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(2, INT_D), IOAPIC_P64H2_2_BUS_B, 7); // Slot 2B (J24) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(3, INT_A), IOAPIC_P64H2_2_BUS_B, 8); // Slot 2C (J25) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(3, INT_B), IOAPIC_P64H2_2_BUS_B, 9); // Slot 2C (J25) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(3, INT_C), IOAPIC_P64H2_2_BUS_B, 10); // Slot 2C (J25) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(3, INT_D), IOAPIC_P64H2_2_BUS_B, 11); // Slot 2C (J25) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(4, INT_A), IOAPIC_P64H2_2_BUS_B, 12); // Slot 2D (J12) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(4, INT_B), IOAPIC_P64H2_2_BUS_B, 13); // Slot 2D (J12) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(4, INT_C), IOAPIC_P64H2_2_BUS_B, 14); // Slot 2D (J12) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_B, PCI_IRQ(4, INT_D), IOAPIC_P64H2_2_BUS_B, 15); // Slot 2D (J12) + + // P64H2#2 Bus A + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_A, PCI_IRQ(1, INT_A), IOAPIC_P64H2_2_BUS_A, 0); // SCSI + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_2_A, PCI_IRQ(1, INT_B), IOAPIC_P64H2_2_BUS_A, 1); // SCSI + + // P64H2#1 Bus B + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(1, INT_A), IOAPIC_P64H2_1_BUS_B, 0); // GB Ethernet + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(2, INT_A), IOAPIC_P64H2_1_BUS_B, 4); // Slot 1B (J21) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(2, INT_B), IOAPIC_P64H2_1_BUS_B, 5); // Slot 1B (J21) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(2, INT_C), IOAPIC_P64H2_1_BUS_B, 6); // Slot 1B (J21) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_B, PCI_IRQ(2, INT_D), IOAPIC_P64H2_1_BUS_B, 7); // Slot 1B (J21) + + // P64H2#1 Bus A + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_A, PCI_IRQ(1, INT_A), IOAPIC_P64H2_1_BUS_A, 0); // Slot 1A (J20) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_A, PCI_IRQ(1, INT_B), IOAPIC_P64H2_1_BUS_A, 1); // Slot 1A (J20) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_A, PCI_IRQ(1, INT_C), IOAPIC_P64H2_1_BUS_A, 2); // Slot 1A (J20) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_P64H2_1_A, PCI_IRQ(1, INT_D), IOAPIC_P64H2_1_BUS_A, 3); // Slot 1A (J20) + + // ICH-3 + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(0, INT_A), IOAPIC_ICH3, 16); // Video + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(2, INT_A), IOAPIC_ICH3, 18); // Debug slot (J11) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(2, INT_B), IOAPIC_ICH3, 19); // Debug slot (J11) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(2, INT_C), IOAPIC_ICH3, 16); // Debug slot (J11) + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, PCI_BUS_ICH3, PCI_IRQ(2, INT_D), IOAPIC_ICH3, 17); // Debug slot (J11) + + // TODO: Not sure how to handle BT_INTR# signals from the P64H2s. Do we even need to, in APIC mode? + + // Super I/O (ISA interrupts) + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 0, IOAPIC_ICH3, 0); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 1, IOAPIC_ICH3, 1); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 0, IOAPIC_ICH3, 2); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 3, IOAPIC_ICH3, 3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 4, IOAPIC_ICH3, 4); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 6, IOAPIC_ICH3, 6); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 8, IOAPIC_ICH3, 8); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 9, IOAPIC_ICH3, 9); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 12, IOAPIC_ICH3, 12); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 13, IOAPIC_ICH3, 13); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 14, IOAPIC_ICH3, 14); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE |MP_IRQ_POLARITY_HIGH, SUPERIO_BUS, 15, IOAPIC_ICH3, 15); +} + +void* smp_write_config_table(void* v) +{ + static const char sig[4] = MPC_SIGNATURE; + static const char oem[8] = "INTEL "; + static const char productid[12] = "XE7501DEVKIT"; + struct mp_config_table *mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); + memset(mc, 0, sizeof(*mc)); + + memcpy(mc->mpc_signature, sig, sizeof(sig)); + memcpy(mc->mpc_oem, oem, sizeof(oem)); + memcpy(mc->mpc_productid, productid, sizeof(productid)); + + mc->mpc_length = sizeof(*mc); // initially just the header + mc->mpc_spec = 0x04; // Multiprocessing Spec V1.4 + mc->mpc_lapic = LAPIC_ADDR; + + smp_write_processors(mc); + + xe7501devkit_register_buses(mc); + xe7501devkit_register_ioapics(mc); + xe7501devkit_register_interrupts(mc); + + /* Compute the checksums */ + mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length); + mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length); + printk_debug("Wrote the mp table end at: %p - %p\n", mc, smp_next_mpe_entry(mc)); + + return smp_next_mpe_entry(mc); +} + +unsigned long write_smp_table(unsigned long addr) +{ + void *v; + v = smp_write_floating_table(addr); + return (unsigned long)smp_write_config_table(v); +} diff --git a/src/mainboard/newisys/khepri/cmos.layout b/src/mainboard/newisys/khepri/cmos.layout index 247715e6ac..0daae9221d 100644 --- a/src/mainboard/newisys/khepri/cmos.layout +++ b/src/mainboard/newisys/khepri/cmos.layout @@ -32,6 +32,7 @@ entries 395 1 e 1 hw_scrubber 396 1 e 1 interleave_chip_selects 397 2 e 8 max_mem_clock +399 1 e 2 dual_core 400 1 e 1 power_on_after_fail 412 4 e 6 debug_level 416 4 e 7 boot_first @@ -41,6 +42,7 @@ entries 432 8 h 0 boot_countdown 440 4 e 9 slow_cpu 444 1 e 1 nmi +445 1 e 1 iommu 728 256 h 0 user_data 984 16 h 0 check_sum # Reserve the extended AMD configuration registers @@ -76,10 +78,10 @@ enumerations 7 9 Fallback_HDD 7 10 Fallback_Floppy #7 3 ROM -8 0 200Mhz -8 1 166Mhz -8 2 133Mhz -8 3 100Mhz +8 0 400Mhz +8 1 333Mhz +8 2 266Mhz +8 3 200Mhz 9 0 off 9 1 87.5% 9 2 75.0% -- cgit v1.2.3