From e30db0e37034f6698eced00727b6ad0ba3fc5c7b Mon Sep 17 00:00:00 2001 From: Edwin Beasant Date: Tue, 9 Feb 2010 10:22:33 +0000 Subject: Port of CS5536 early UART setup from v3. Permit early setup of COM2 Signed-off-by: Edwin Beasant Acked-by: Patrick Georgi git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5097 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1 --- src/southbridge/amd/cs5536/cs5536.c | 84 +++++++++++++++---------- src/southbridge/amd/cs5536/cs5536_early_setup.c | 75 ++++++++++++++++++---- 2 files changed, 114 insertions(+), 45 deletions(-) (limited to 'src/southbridge/amd/cs5536') diff --git a/src/southbridge/amd/cs5536/cs5536.c b/src/southbridge/amd/cs5536/cs5536.c index 474424bba6..905d71f052 100644 --- a/src/southbridge/amd/cs5536/cs5536.c +++ b/src/southbridge/amd/cs5536/cs5536.c @@ -247,38 +247,45 @@ static void lpc_init(struct southbridge_amd_cs5536_config *sb) isa_dma_init(); } + +/** + * Depending on settings in the config struct, enable COM1 or COM2 or both. + * + * If the enable is NOT set, the UARTs are explicitly disabled, which is + * required if (e.g.) there is a Super I/O attached that does COM1 or COM2. + * + * @param sb Southbridge config structure. + */ static void uarts_init(struct southbridge_amd_cs5536_config *sb) { msr_t msr; - uint16_t addr; - uint32_t gpio_addr; + u16 addr = 0; + u32 gpio_addr; device_t dev; - + dev = dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, 0); gpio_addr = pci_read_config32(dev, PCI_BASE_ADDRESS_1); - gpio_addr &= ~1; /* clear IO bit */ - printk_debug("GPIO_ADDR: %08X\n", gpio_addr); + gpio_addr &= ~1; /* Clear I/O bit */ + printk(BIOS_DEBUG, "GPIO_ADDR: %08X\n", gpio_addr); - /* This could be extended to support IR modes */ + /* This could be extended to support IR modes. */ /* COM1 */ if (sb->com1_enable) { - /* Set the address */ + printk(BIOS_SPEW, "uarts_init: enable COM1\n"); + /* Set the address. */ switch (sb->com1_address) { case 0x3F8: addr = 7; break; - case 0x3E8: addr = 6; break; - case 0x2F8: addr = 5; break; - case 0x2E8: addr = 4; break; @@ -287,13 +294,13 @@ static void uarts_init(struct southbridge_amd_cs5536_config *sb) msr.lo |= addr << 16; wrmsr(MDD_LEG_IO, msr); - /* Set the IRQ */ + /* Set the IRQ. */ msr = rdmsr(MDD_IRQM_YHIGH); msr.lo |= sb->com1_irq << 24; wrmsr(MDD_IRQM_YHIGH, msr); /* GPIO8 - UART1_TX */ - /* Set: Output Enable (0x4) */ + /* Set: Output Enable (0x4) */ outl(GPIOL_8_SET, gpio_addr + GPIOL_OUTPUT_ENABLE); /* Set: OUTAUX1 Select (0x10) */ outl(GPIOL_8_SET, gpio_addr + GPIOL_OUT_AUX1_SELECT); @@ -301,28 +308,31 @@ static void uarts_init(struct southbridge_amd_cs5536_config *sb) /* GPIO9 - UART1_RX */ /* Set: Input Enable (0x20) */ outl(GPIOL_9_SET, gpio_addr + GPIOL_INPUT_ENABLE); - /* Set: INAUX1 Select (0x34) */ + /* Set: INAUX1 Select (0x34) */ outl(GPIOL_9_SET, gpio_addr + GPIOL_IN_AUX1_SELECT); - /* Set: GPIO 8 + 9 Pull Up (0x18) */ + /* Set: GPIO 8 + 9 Pull Up (0x18) */ outl(GPIOL_8_SET | GPIOL_9_SET, gpio_addr + GPIOL_PULLUP_ENABLE); - /* enable COM1 */ - /* Bit 1 = device enable Bit 4 = allow access to the upper banks */ + /* Enable COM1. + * + * Bit 1 = device enable + * Bit 4 = allow access to the upper banks + */ msr.lo = (1 << 4) | (1 << 1); msr.hi = 0; wrmsr(MDD_UART1_CONF, msr); - } else { - /* Reset and disable COM1 */ + /* Reset and disable COM1. */ + printk(BIOS_SPEW, "uarts_init: disable COM1\n"); msr = rdmsr(MDD_UART1_CONF); - msr.lo = 1; // reset + msr.lo = 1; /* Reset */ wrmsr(MDD_UART1_CONF, msr); - msr.lo = 0; // disabled + msr.lo = 0; /* Disabled */ wrmsr(MDD_UART1_CONF, msr); - /* Disable the IRQ */ + /* Disable the IRQ. */ msr = rdmsr(MDD_LEG_IO); msr.lo &= ~(0xF << 16); wrmsr(MDD_LEG_IO, msr); @@ -330,19 +340,17 @@ static void uarts_init(struct southbridge_amd_cs5536_config *sb) /* COM2 */ if (sb->com2_enable) { + printk(BIOS_SPEW, "uarts_init: enable COM2\n"); switch (sb->com2_address) { case 0x3F8: addr = 7; break; - case 0x3E8: addr = 6; break; - case 0x2F8: addr = 5; break; - case 0x2E8: addr = 4; break; @@ -350,11 +358,13 @@ static void uarts_init(struct southbridge_amd_cs5536_config *sb) msr = rdmsr(MDD_LEG_IO); msr.lo |= addr << 20; wrmsr(MDD_LEG_IO, msr); + printk(BIOS_SPEW, "uarts_init: wrote COM2 address 0x%x\n", sb->com2_address); - /* Set the IRQ */ + /* Set the IRQ. */ msr = rdmsr(MDD_IRQM_YHIGH); msr.lo |= sb->com2_irq << 28; wrmsr(MDD_IRQM_YHIGH, msr); + printk(BIOS_SPEW, "uarts_init: set COM2 irq\n"); /* GPIO3 - UART2_RX */ /* Set: Input Enable (0x20) */ @@ -365,34 +375,42 @@ static void uarts_init(struct southbridge_amd_cs5536_config *sb) /* GPIO4 - UART2_TX */ /* Set: Output Enable (0x4) */ outl(GPIOL_4_SET, gpio_addr + GPIOL_OUTPUT_ENABLE); + printk(BIOS_SPEW, "uarts_init: set output enable\n"); /* Set: OUTAUX1 Select (0x10) */ outl(GPIOL_4_SET, gpio_addr + GPIOL_OUT_AUX1_SELECT); + printk(BIOS_SPEW, "uarts_init: set OUTAUX1\n"); - /* Set: GPIO 3 and 4 Pull Up (0x18) */ + /* Set: GPIO 3 + 4 Pull Up (0x18) */ outl(GPIOL_3_SET | GPIOL_4_SET, gpio_addr + GPIOL_PULLUP_ENABLE); + printk(BIOS_SPEW, "uarts_init: set pullup COM2\n"); - /* enable COM2 */ - /* Bit 1 = device enable Bit 4 = allow access to the upper banks */ + /* Enable COM2. + * + * Bit 1 = device enable + * Bit 4 = allow access to the upper banks + */ msr.lo = (1 << 4) | (1 << 1); msr.hi = 0; wrmsr(MDD_UART2_CONF, msr); - + printk(BIOS_SPEW, "uarts_init: COM2 enabled\n"); } else { - /* Reset and disable COM2 */ + printk(BIOS_SPEW, "uarts_init: disable COM2\n"); + /* Reset and disable COM2. */ msr = rdmsr(MDD_UART2_CONF); - msr.lo = 1; // reset + msr.lo = 1; /* Reset */ wrmsr(MDD_UART2_CONF, msr); - msr.lo = 0; // disabled + msr.lo = 0; /* Disabled */ wrmsr(MDD_UART2_CONF, msr); - /* Disable the IRQ */ + /* Disable the IRQ. */ msr = rdmsr(MDD_LEG_IO); msr.lo &= ~(0xF << 20); wrmsr(MDD_LEG_IO, msr); } } + #define HCCPARAMS 0x08 #define IPREG04 0xA0 #define USB_HCCPW_SET (1 << 1) diff --git a/src/southbridge/amd/cs5536/cs5536_early_setup.c b/src/southbridge/amd/cs5536/cs5536_early_setup.c index 7c67d1f042..fd09764212 100644 --- a/src/southbridge/amd/cs5536/cs5536_early_setup.c +++ b/src/southbridge/amd/cs5536/cs5536_early_setup.c @@ -153,47 +153,98 @@ static void cs5536_setup_cis_mode(void) wrmsr(GLPCI_SB_CTRL, msr); } -/* see page 412 of the cs5536 companion book */ -static void cs5536_setup_onchipuart(void) +/** + * Enable the on-chip UART. + * + * See page 412 of the AMD Geode CS5536 Companion Device data book. + */ +void cs5536_setup_onchipuart1(void) { msr_t msr; /* Setup early for polling only mode. - * 1. Eanble GPIO 8 to OUT_AUX1, 9 to IN_AUX1 + * 1. Enable GPIO 8 to OUT_AUX1, 9 to IN_AUX1. * GPIO LBAR + 0x04, LBAR + 0x10, LBAR + 0x20, LBAR + 34 - * 2. Enable UART IO space in MDD + * 2. Enable UART I/O space in MDD. * MSR 0x51400014 bit 18:16 - * 3. Enable UART controller + * 3. Enable UART controller. * MSR 0x5140003A bit 0, 1 */ /* GPIO8 - UART1_TX */ - /* Set: Output Enable (0x4) */ + /* Set: Output Enable (0x4) */ outl(GPIOL_8_SET, GPIO_IO_BASE + GPIOL_OUTPUT_ENABLE); /* Set: OUTAUX1 Select (0x10) */ outl(GPIOL_8_SET, GPIO_IO_BASE + GPIOL_OUT_AUX1_SELECT); /* GPIO9 - UART1_RX */ - /* Set: Input Enable (0x20) */ + /* Set: Input Enable (0x20) */ outl(GPIOL_9_SET, GPIO_IO_BASE + GPIOL_INPUT_ENABLE); - /* Set: INAUX1 Select (0x34) */ + /* Set: INAUX1 Select (0x34) */ outl(GPIOL_9_SET, GPIO_IO_BASE + GPIOL_IN_AUX1_SELECT); - /* set address to 3F8 */ + /* Set address to 0x3F8. */ msr = rdmsr(MDD_LEG_IO); msr.lo |= 0x7 << 16; wrmsr(MDD_LEG_IO, msr); - /* Bit 1 = DEVEN (device enable) - * Bit 4 = EN_BANKS (allow access to the upper banks + /* Bit 1 = DEVEN (device enable) + * Bit 4 = EN_BANKS (allow access to the upper banks) */ msr.lo = (1 << 4) | (1 << 1); msr.hi = 0; - /* enable COM1 */ + /* Enable COM1. */ wrmsr(MDD_UART1_CONF, msr); } +void cs5536_setup_onchipuart2(void) +{ + msr_t msr; + + /* GPIO4 - UART2_TX */ + /* Set: Output Enable (0x4) */ + outl(GPIOL_4_SET, GPIO_IO_BASE + GPIOL_OUTPUT_ENABLE); + /* Set: OUTAUX1 Select (0x10) */ + outl(GPIOL_4_SET, GPIO_IO_BASE + GPIOL_OUT_AUX1_SELECT); + /* GPIO4 - UART2_RX */ + /* Set: Input Enable (0x20) */ + outl(GPIOL_3_SET, GPIO_IO_BASE + GPIOL_INPUT_ENABLE); + /* Set: INAUX1 Select (0x34) */ + outl(GPIOL_3_SET, GPIO_IO_BASE + GPIOL_IN_AUX1_SELECT); + + /* Set: GPIO 3 + 3 Pull Up (0x18) */ + outl(GPIOL_3_SET | GPIOL_4_SET, + GPIO_IO_BASE + GPIOL_PULLUP_ENABLE); + + /* set address to 2F8 */ + msr = rdmsr(MDD_LEG_IO); + msr.lo |= 0x5 << 20; + wrmsr(MDD_LEG_IO, msr); + + /* Bit 1 = DEVEN (device enable) + * Bit 4 = EN_BANKS (allow access to the upper banks + */ + msr.lo = (1 << 4) | (1 << 1); + msr.hi = 0; + + /* enable COM2 */ + wrmsr(MDD_UART2_CONF, msr); +} + +void cs5536_setup_onchipuart(int uart) +{ + switch (uart) { + case 1: + cs5536_setup_onchipuart1(); + break; + case 2: + cs5536_setup_onchipuart2(); + break; + } +} + + /* note: you can't do prints in here in most cases, * and we don't want to hang on serial, so they are * commented out -- cgit v1.2.3