From e05aafbc6754c48936377be79e6dd5349e6fd7b5 Mon Sep 17 00:00:00 2001 From: Maxim Polyakov Date: Wed, 12 Aug 2020 12:58:17 +0300 Subject: mb/siemens/mc_apl2/gpio: Undo set DRIVER for GPO GPIO Driver mode is used for configuration interrupt routing for external devices through GPI. But there is no point in configuring this for GPO. This patch replaces the PAD_CFG_GPO_GPIO_DRIVER macro with others that do not set the corresponding bit in the Host Software Pad Ownership register. Change-Id: I406a08e526a6c655f38e4c0a355957c98e93881c Signed-off-by: Maxim Polyakov Reviewed-on: https://review.coreboot.org/c/coreboot/+/44469 Tested-by: build bot (Jenkins) Reviewed-by: Mario Scheithauer --- .../siemens/mc_apl1/variants/mc_apl2/gpio.c | 36 +++++++++++----------- 1 file changed, 18 insertions(+), 18 deletions(-) (limited to 'src') diff --git a/src/mainboard/siemens/mc_apl1/variants/mc_apl2/gpio.c b/src/mainboard/siemens/mc_apl1/variants/mc_apl2/gpio.c index aa4a906c5a..b770bdcbee 100644 --- a/src/mainboard/siemens/mc_apl1/variants/mc_apl2/gpio.c +++ b/src/mainboard/siemens/mc_apl1/variants/mc_apl2/gpio.c @@ -74,7 +74,7 @@ static const struct pad_config gpio_table[] = { /* SDCARD_WP_1V8 */ PAD_CFG_GPI_GPIO_DRIVER(GPIO_186, DN_20K, DEEP), /* SD_PWR_EN_1V8 - Always enabled SDCard. */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_183, 0, DEEP, UP_20K), + PAD_CFG_TERM_GPO(GPIO_183, 0, UP_20K, DEEP), /* West Community */ @@ -208,15 +208,15 @@ static const struct pad_config gpio_table[] = { /* EDP_VDD_EN_1V8 (DNI) - Alternative stuffing option for * PTN3460 LVDS_VDD_EN. */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_196, 1, DEEP, UP_20K), + PAD_CFG_TERM_GPO(GPIO_196, 1, UP_20K, DEEP), /* EDP_BKLT_EN_1V8 (DNI) - Alternative stuffing option for * PTN3460 LVDS_BKLT_EN */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_197, 1, DEEP, UP_20K), + PAD_CFG_TERM_GPO(GPIO_197, 1, UP_20K, DEEP), /* EDP_BKLT_CTRL_1V8 - Alternative stuffing option for * PTN3460 LVDS_BKLT_CTRL */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_198, 1, DEEP, UP_20K), + PAD_CFG_TERM_GPO(GPIO_198, 1, UP_20K, DEEP), /* DDI1_HPD# - Connect to DP1_HPD Hot plug detection signal of SMARC * Connector. @@ -263,8 +263,8 @@ static const struct pad_config gpio_table[] = { /* Not connected */ PAD_CFG_NF(PMIC_PWRGOOD, UP_20K, DEEP, NF1), - PAD_CFG_GPO_GPIO_DRIVER(GPIO_214, 1, DEEP, DN_20K), - PAD_CFG_GPO_GPIO_DRIVER(GPIO_215, 1, DEEP, DN_20K), + PAD_CFG_TERM_GPO(GPIO_214, 1, DN_20K, DEEP), + PAD_CFG_TERM_GPO(GPIO_215, 1, DN_20K, DEEP), /* THERMTRIP_1V8# - Connected to CPLD */ PAD_CFG_NF_IOSSTATE_IOSTERM(PMIC_THERMTRIP_B, UP_20K, DEEP, NF1, TxLASTRxE, SAME), @@ -390,15 +390,15 @@ static const struct pad_config gpio_table[] = { /* OTG_SEL_1V8 - Connected to a USB MUX to select between USB2_DP0 (OTG) * and USB2_DP6. 1:OTG, 0:USB */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_9, 1, DEEP, UP_20K), + PAD_CFG_TERM_GPO(GPIO_9, 1, UP_20K, DEEP), /* EN_I2CPM_EXT_1V8 - Connected to OE pin of I2C Re-driver. * Allow/Disallow I2C signal to pass through to SMARC Connector. */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_10, 1, DEEP, UP_20K), + PAD_CFG_TERM_GPO(GPIO_10, 1, UP_20K, DEEP), /* EN_SMB_EXT_1V8 - Connected to OE pin of I2C Re-driver. * Allow/Disallow SMBUS signal to pass through to SMARC Connector. */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_11, 0, DEEP, UP_20K), + PAD_CFG_TERM_GPO(GPIO_11, 0, UP_20K, DEEP), /* BOOT_SEL2_1V8# - Three Module pins allow the Carrier board user to * select from eight possible boot devices. */ @@ -413,13 +413,13 @@ static const struct pad_config gpio_table[] = { */ PAD_CFG_GPI_INT(GPIO_14, UP_20K, DEEP, OFF), /* GPIO_CPLD_TCK_1V8 */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_15, 0, DEEP, DN_20K), + PAD_CFG_TERM_GPO(GPIO_15, 0, DN_20K, DEEP), /* GPIO_CPLD_TMS_1V8 */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_16, 0, DEEP, DN_20K), + PAD_CFG_TERM_GPO(GPIO_16, 0, DN_20K, DEEP), /* GPIO_CPLD_TDI_1V8 */ PAD_CFG_GPI_INT(GPIO_17, DN_20K, DEEP, OFF), /* GPIO_CPLD_TDO_1V8 */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_18, 0, DEEP, DN_20K), + PAD_CFG_TERM_GPO(GPIO_18, 0, DN_20K, DEEP), /* PM_TEST_1V8# connect to the SMARC Connector TEST# pin. * Held low by Carrier to invoke Module vendor specific test function. * Pulled up on Module. Driven by OD part on Carrier. @@ -464,9 +464,9 @@ static const struct pad_config gpio_table[] = { /* SMB_ALERT_GPIO# */ PAD_CFG_GPI_INT(GPIO_27, UP_20K, DEEP, OFF), /* GPIO_28_DEBUG - Connect to HOOK5 (ClkOut#) pin of XDP connector */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_28, 1, DEEP, UP_20K), + PAD_CFG_TERM_GPO(GPIO_28, 1, UP_20K, DEEP), /* GPIO_29_DEBUG - Connect to HOOK4 (ClkOut) pin of XDP connector */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_29, 0, DEEP, DN_20K), + PAD_CFG_TERM_GPO(GPIO_29, 0, DN_20K, DEEP), /* Not connected */ PAD_CFG_GPI_INT(GPIO_30, DN_20K, DEEP, OFF), @@ -484,21 +484,21 @@ static const struct pad_config gpio_table[] = { /* STRAP_GPIO_36 (int. PD) */ PAD_CFG_GPI_INT(GPIO_36, DN_20K, DEEP, OFF), /* Not connected */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_37, 0, DEEP, DN_20K), + PAD_CFG_TERM_GPO(GPIO_37, 0, DN_20K, DEEP), /* GPIO_VALID (CPLD=gpio_valid/pi_gpio_en)- This pin Enable the CPLD * GPIO to the SMARC Connector. */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_62, 1, DEEP, UP_20K), + PAD_CFG_TERM_GPO(GPIO_62, 1, UP_20K, DEEP), /* LVDS_ENABLE_1V8# connect to PTN3460 DP to LVDS converter chip. */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_63, 0, DEEP, DN_20K), + PAD_CFG_TERM_GPO(GPIO_63, 0, DN_20K, DEEP), /* Not connected */ PAD_CFG_GPIO_DRIVER_HI_Z(GPIO_64, DN_20K, DEEP, HIZCRx0, SAME), /* Not connected */ PAD_CFG_GPIO_DRIVER_HI_Z(GPIO_65, DN_20K, DEEP, HIZCRx0, SAME), /* CAM_CS0_CS1_SEL - Serial Cameras interfaces Select - to select * between the two MIPI CSI camera interfaces on the SMARC connector. */ - PAD_CFG_GPO_GPIO_DRIVER(GPIO_66, 0, DEEP, DN_20K), + PAD_CFG_TERM_GPO(GPIO_66, 0, DN_20K, DEEP), /* MCSI0_RST_1V8# - Reset the MIPI CSI camera interfaces 0 */ PAD_CFG_GPO_IOSSTATE_IOSTERM(GPIO_67, 0, DEEP, DN_20K, HIZCRx0, SAME), /* MCSI1_RST_1V8# - Reset the MIPI CSI camera interfaces 1 */ -- cgit v1.2.3