/* * This file is part of the coreboot project. * * Copyright (C) 2011 Samsung Electronics * Copyright 2013 Google Inc. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; version 2 of the License. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ #include #include #include #include #include #include "cpu.h" #include "spi.h" #define EXYNOS_SPI_MAX_TRANSFER_BYTES (65535) #if defined(CONFIG_DEBUG_SPI) && CONFIG_DEBUG_SPI # define DEBUG_SPI(x,...) printk(BIOS_DEBUG, "EXYNOS_SPI: " x) #else # define DEBUG_SPI(x,...) #endif struct exynos_spi_slave { struct spi_slave slave; struct exynos_spi *regs; unsigned int fifo_size; uint8_t half_duplex; uint8_t frame_header; /* header byte to detect in half-duplex mode. */ }; /* TODO(hungte) Move the SPI param list to per-board configuration, probably * Kconfig or mainboard.c */ static struct exynos_spi_slave exynos_spi_slaves[3] = { // SPI 0 { .slave = { .bus = 0, }, .regs = samsung_get_base_spi0(), }, // SPI 1 { .slave = { .bus = 1, .rw = SPI_READ_FLAG, }, .regs = samsung_get_base_spi1(), .fifo_size = 64, .half_duplex = 0, }, // SPI 2 { .slave = { .bus = 2, .rw = SPI_READ_FLAG | SPI_WRITE_FLAG, }, .regs = samsung_get_base_spi2(), .fifo_size = 64, .half_duplex = 1, .frame_header = 0xec, }, }; static inline struct exynos_spi_slave *to_exynos_spi(struct spi_slave *slave) { return container_of(slave, struct exynos_spi_slave, slave); } void spi_init(void) { printk(BIOS_INFO, "Exynos SPI driver initiated.\n"); } struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, unsigned int max_hz, unsigned int mode) { ASSERT(bus >= 0 && bus < 3); return &(exynos_spi_slaves[bus].slave); } int spi_cs_is_valid(unsigned int bus, unsigned int cs) { return bus > 0 && bus < 3; } void spi_cs_activate(struct spi_slave *slave) { struct exynos_spi *regs = to_exynos_spi(slave)->regs; // TODO(hungte) Add some delay if too many transactions happen at once. clrbits_le32(®s->cs_reg, SPI_SLAVE_SIG_INACT); } void spi_cs_deactivate(struct spi_slave *slave) { struct exynos_spi *regs = to_exynos_spi(slave)->regs; setbits_le32(®s->cs_reg, SPI_SLAVE_SIG_INACT); } static inline void exynos_spi_soft_reset(struct exynos_spi *regs) { /* The soft reset clears only FIFO and status register. * All special function registers are not changed. */ setbits_le32(®s->ch_cfg, SPI_CH_RST); clrbits_le32(®s->ch_cfg, SPI_CH_RST); } static inline void exynos_spi_flush_fifo(struct exynos_spi *regs) { /* * Flush spi tx, rx fifos and reset the SPI controller * and clear rx/tx channel */ clrbits_le32(®s->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON); clrbits_le32(®s->ch_cfg, SPI_CH_HS_EN); exynos_spi_soft_reset(regs); setbits_le32(®s->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON); } static void exynos_spi_request_bytes(struct exynos_spi *regs, int count, int width) { uint32_t mode_word = SPI_MODE_CH_WIDTH_WORD | SPI_MODE_BUS_WIDTH_WORD, swap_word = (SPI_TX_SWAP_EN | SPI_RX_SWAP_EN | SPI_TX_BYTE_SWAP | SPI_RX_BYTE_SWAP | SPI_TX_HWORD_SWAP | SPI_RX_HWORD_SWAP); /* For word address we need to swap bytes */ if (width == sizeof(uint32_t)) { setbits_le32(®s->mode_cfg, mode_word); setbits_le32(®s->swap_cfg, swap_word); count /= width; } else { /* Select byte access and clear the swap configuration */ clrbits_le32(®s->mode_cfg, mode_word); writel(0, ®s->swap_cfg); } exynos_spi_soft_reset(regs); if (count) { ASSERT(count < (1 << 16)); writel(count | SPI_PACKET_CNT_EN, ®s->pkt_cnt); } else { writel(0, ®s->pkt_cnt); } } static int spi_rx_tx(struct spi_slave *slave, uint8_t *rxp, int rx_bytes, const uint8_t *txp, int tx_bytes) { struct exynos_spi_slave *espi = to_exynos_spi(slave); struct exynos_spi *regs = espi->regs; int step; int todo = MAX(rx_bytes, tx_bytes); int wait_for_frame_header = espi->half_duplex; ASSERT(todo < EXYNOS_SPI_MAX_TRANSFER_BYTES); /* Select transfer mode. */ if (espi->half_duplex) { step = 1; } else if ((rx_bytes | tx_bytes | (uintptr_t)rxp |(uintptr_t)txp) & 3) { printk(BIOS_CRIT, "%s: WARNING: tranfer mode decreased to 1B\n", __func__); step = 1; } else { step = sizeof(uint32_t); } exynos_spi_request_bytes(regs, espi->half_duplex ? 0 : todo, step); /* Note: Some device, like ChromeOS EC, tries to work in half-duplex * mode and sends a large amount of data (larger than FIFO size). * Printing lots of debug messages or doing extra delay in the loop * below may cause rx buffer to overflow and getting unexpected data * error. */ while (rx_bytes || tx_bytes) { int temp; uint32_t spi_sts = readl(®s->spi_sts); int rx_lvl = (spi_sts >> SPI_RX_LVL_OFFSET) & SPI_FIFO_LVL_MASK, tx_lvl = (spi_sts >> SPI_TX_LVL_OFFSET) & SPI_FIFO_LVL_MASK; int min_tx = ((tx_bytes || !espi->half_duplex) ? (espi->fifo_size / 2) : 1); // TODO(hungte) Abort if timeout happens in half-duplex mode. /* * Don't completely fill the txfifo, since we don't want our * rxfifo to overflow, and it may already contain data. */ while (tx_lvl < min_tx) { if (tx_bytes) { if (step == sizeof(uint32_t)) { temp = *((uint32_t *)txp); txp += sizeof(uint32_t); } else { temp = *txp++; } tx_bytes -= step; } else { temp = -1; } writel(temp, ®s->tx_data); tx_lvl += step; } while ((rx_lvl >= step) && rx_bytes) { temp = readl(®s->rx_data); rx_lvl -= step; if (wait_for_frame_header) { if ((temp & 0xff) == espi->frame_header) { wait_for_frame_header = 0; } break; /* Restart the outer loop. */ } if (step == sizeof(uint32_t)) { *((uint32_t *)rxp) = temp; rxp += sizeof(uint32_t); } else { *rxp++ = temp; } rx_bytes -= step; } } return 0; } int spi_claim_bus(struct spi_slave *slave) { struct exynos_spi_slave *espi = to_exynos_spi(slave); struct exynos_spi *regs = espi->regs; exynos_spi_flush_fifo(regs); // Select Active High Clock, Format A (SCP 30.2.1.8). clrbits_le32(®s->ch_cfg, SPI_CH_CPOL_L | SPI_CH_CPHA_B); // Set FeedBack Clock Selection. writel(SPI_FB_DELAY_180, ®s->fb_clk); // HIGH speed is required for Tx/Rx to work in 50MHz (SCP 30.2.1.6). if (espi->half_duplex) { clrbits_le32(®s->ch_cfg, SPI_CH_HS_EN); printk(BIOS_DEBUG, "%s: LOW speed.\n", __func__); } else { setbits_le32(®s->ch_cfg, SPI_CH_HS_EN); printk(BIOS_DEBUG, "%s: HIGH speed.\n", __func__); } return 0; } int spi_xfer(struct spi_slave *slave, const void *dout, unsigned int bitsout, void *din, unsigned int bitsin) { unsigned int out_bytes = bitsout / 8, in_bytes = bitsin / 8; uint8_t *out_ptr = (uint8_t *)dout, *in_ptr = (uint8_t *)din; int offset, todo, len; int ret = 0; ASSERT(bitsout % 8 == 0 && bitsin % 8 == 0); len = MAX(out_bytes, in_bytes); /* * Exynos SPI limits each transfer to (2^16-1=65535) bytes. To keep * things simple (especially for word-width transfer mode), allow a * maximum of (2^16-4=65532) bytes. We could allow more in word mode, * but the performance difference is small. */ spi_cs_activate(slave); for (offset = 0; !ret && (offset < len); offset += todo) { todo = min(len - offset, (1 << 16) - 4); ret = spi_rx_tx(slave, in_ptr, MIN(in_bytes, todo), out_ptr, MIN(out_bytes, todo)); // Adjust remaining bytes and pointers. if (in_bytes >= todo) { in_bytes -= todo; in_ptr += todo; } else { in_bytes = 0; in_ptr = NULL; } if (out_bytes >= todo) { out_bytes -= todo; out_ptr += todo; } else { out_bytes = 0; out_ptr = NULL; } } spi_cs_deactivate(slave); return ret; } static int exynos_spi_read(struct spi_slave *slave, void *dest, uint32_t len, uint32_t off) { struct exynos_spi *regs = to_exynos_spi(slave)->regs; int rv; // TODO(hungte) Merge the "read address" command into spi_xfer calls // (full-duplex mode). spi_cs_activate(slave); // Specify read address (in word-width mode). ASSERT(off < (1 << 24)); exynos_spi_request_bytes(regs, sizeof(off), sizeof(off)); writel(htonl((SF_READ_DATA_CMD << 24) | off), ®s->tx_data); while (!(readl(®s->spi_sts) & SPI_ST_TX_DONE)) { /* Wait for TX done */ } // Now, safe to transfer. rv = spi_xfer(slave, NULL, 0, dest, len * 8); spi_cs_deactivate(slave); return (rv == 0) ? len : -1; } void spi_release_bus(struct spi_slave *slave) { struct exynos_spi *regs = to_exynos_spi(slave)->regs; /* Reset swap mode to make sure no one relying on default values (Ex, * payload or kernel) will go wrong. */ clrbits_le32(®s->mode_cfg, (SPI_MODE_CH_WIDTH_WORD | SPI_MODE_BUS_WIDTH_WORD)); writel(0, ®s->swap_cfg); exynos_spi_flush_fifo(regs); } // SPI as CBFS media. struct exynos_spi_media { struct spi_slave *slave; struct cbfs_simple_buffer buffer; }; static int exynos_spi_cbfs_open(struct cbfs_media *media) { struct exynos_spi_media *spi = (struct exynos_spi_media*)media->context; DEBUG_SPI("exynos_spi_cbfs_open\n"); return spi_claim_bus(spi->slave); } static int exynos_spi_cbfs_close(struct cbfs_media *media) { struct exynos_spi_media *spi = (struct exynos_spi_media*)media->context; DEBUG_SPI("exynos_spi_cbfs_close\n"); spi_release_bus(spi->slave); return 0; } static size_t exynos_spi_cbfs_read(struct cbfs_media *media, void *dest, size_t offset, size_t count) { struct exynos_spi_media *spi = (struct exynos_spi_media*)media->context; int bytes; DEBUG_SPI("exynos_spi_cbfs_read(%u)\n", count); bytes = exynos_spi_read(spi->slave, dest, count, offset); return bytes; } static void *exynos_spi_cbfs_map(struct cbfs_media *media, size_t offset, size_t count) { struct exynos_spi_media *spi = (struct exynos_spi_media*)media->context; DEBUG_SPI("exynos_spi_cbfs_map\n"); // exynos: spi_rx_tx may work in 4 byte-width-transmission mode and // requires buffer memory address to be aligned. if (count % 4) count += 4 - (count % 4); return cbfs_simple_buffer_map(&spi->buffer, media, offset, count); } static void *exynos_spi_cbfs_unmap(struct cbfs_media *media, const void *address) { struct exynos_spi_media *spi = (struct exynos_spi_media*)media->context; DEBUG_SPI("exynos_spi_cbfs_unmap\n"); return cbfs_simple_buffer_unmap(&spi->buffer, address); } int initialize_exynos_spi_cbfs_media(struct cbfs_media *media, void *buffer_address, size_t buffer_size) { // TODO Replace static variable to support multiple streams. static struct exynos_spi_media context; static struct exynos_spi_slave eslave = { .slave = { .bus = 1, .rw = SPI_READ_FLAG, }, .regs = samsung_get_base_spi1(), .fifo_size = 64, .half_duplex = 0, }; DEBUG_SPI("initialize_exynos_spi_cbfs_media\n"); context.slave = &eslave.slave; context.buffer.allocated = context.buffer.last_allocate = 0; context.buffer.buffer = buffer_address; context.buffer.size = buffer_size; media->context = (void*)&context; media->open = exynos_spi_cbfs_open; media->close = exynos_spi_cbfs_close; media->read = exynos_spi_cbfs_read; media->map = exynos_spi_cbfs_map; media->unmap = exynos_spi_cbfs_unmap; return 0; } int init_default_cbfs_media(struct cbfs_media *media) { return initialize_exynos_spi_cbfs_media( media, (void*)CONFIG_CBFS_CACHE_ADDRESS, CONFIG_CBFS_CACHE_SIZE); }