chip soc/intel/cannonlake

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| GSPI0             | cr50 TPM. Early init is   |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#|                   | before memory is up       |
	#| GSPI1             | FP MCU                    |
	#| I2C0              | Touchpad                  |
	#| I2C1              | Touch screen              |
	#| I2C4              | Audio                     |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.gspi[0] = {
			.speed_mhz = 1,
			.early_init = 1,
		},
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[1] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[4] = {
			.speed = I2C_SPEED_FAST,
		},
	}"

	# GPIO for SD card detect
	register "sdcard_cd_gpio" = "vSD3_CD_B"

	# USB configuration
	register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)"	# Discrete BT

	device domain 0 on
		device pci 14.0 on
			chip drivers/usb/acpi
				register "desc" = ""Root Hub""
				register "type" = "UPC_TYPE_HUB"
				device usb 0.0 on
					chip drivers/usb/acpi
						register "desc" = ""Discrete bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C14)"
						device usb 2.4 on end
					end
				end
			end
		end # USB xHCI
		device pci 15.0 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D21_IRQ)"
				register "wake" = "GPE0_DW0_21"
				device i2c 15 on end
			end
		end # I2C #0
		device pci 15.1 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0001""
				register "desc" = ""ELAN Touchscreen""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)"
				register "probed" = "1"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)"
				register "reset_delay_ms" = "100"
				register "reset_off_delay_ms" = "5"
				register "has_power_resource" = "1"
				register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C4)"
				register "stop_off_delay_ms" = "5"
				device i2c 49 on end
			end
			chip drivers/i2c/hid
				register "generic.hid" = ""GDIX0000""
				register "generic.desc" = ""Goodix Touchscreen""
				register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)"
				register "generic.probed" = "1"
				register "generic.reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)"
				register "generic.reset_delay_ms" = "10"
				register "generic.reset_off_delay_ms" = "3"
				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D9)"
                                register "generic.enable_delay_ms" = "12"
				register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x01"
				device i2c 5d on end
			end
			chip drivers/generic/gpio_keys
				register "name" = ""PENH""
				register "gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A8)"
				register "key.wake" = "GPE0_DW0_08"
				register "key.wakeup_event_action" = "EV_ACT_DEASSERTED"
				register "key.dev_name" = ""EJCT""
				register "key.linux_code" = "SW_PEN_INSERTED"
				register "key.linux_input_type" = "EV_SW"
				register "key.label" = ""pen_eject""
				device generic 0 on end
			end
		end # I2C #1
		device pci 15.2 off end # I2C #2
		device pci 15.3 on
			chip drivers/i2c/sx9310
				register "desc" = ""SAR Proximity Sensor""
				register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A0)"
				register "speed" = "I2C_SPEED_FAST"
				register "uid" = "1"
				register "reg_prox_ctrl0" = "0x10"
				register "reg_prox_ctrl1" = "0x00"
				register "reg_prox_ctrl2" = "0x84"
				register "reg_prox_ctrl3" = "0x0e"
				register "reg_prox_ctrl4" = "0x07"
				register "reg_prox_ctrl5" = "0xc6"
				register "reg_prox_ctrl6" = "0x20"
				register "reg_prox_ctrl7" = "0x0d"
				register "reg_prox_ctrl8" = "0x8d"
				register "reg_prox_ctrl9" = "0x43"
				register "reg_prox_ctrl10" = "0x1f"
				register "reg_prox_ctrl11" = "0x00"
				register "reg_prox_ctrl12" = "0x00"
				register "reg_prox_ctrl13" = "0x00"
				register "reg_prox_ctrl14" = "0x00"
				register "reg_prox_ctrl15" = "0x00"
				register "reg_prox_ctrl16" = "0x00"
				register "reg_prox_ctrl17" = "0x00"
				register "reg_prox_ctrl18" = "0x00"
				register "reg_prox_ctrl19" = "0x00"
				register "reg_sar_ctrl0" = "0x50"
				register "reg_sar_ctrl1" = "0x8a"
				register "reg_sar_ctrl2" = "0x3c"
				device i2c 28 on end
			end
		end # I2C #3
		device pci 19.0 on
			chip drivers/i2c/generic
				register "hid" = ""10EC5682""
				register "name" = ""RT58""
				register "desc" = ""Realtek RT5682""
				register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_H0)"
				register "property_count" = "1"
				# Set the jd_src to RT5668_JD1 for jack detection
				register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
				register "property_list[0].name" = ""realtek,jd-src""
				register "property_list[0].integer" = "1"
				device i2c 1a on end
			end
		end #I2C #4
		device pci 1e.3 on
			chip drivers/spi/acpi
				register "name" = ""CRFP""
				register "hid" = "ACPI_DT_NAMESPACE_HID"
				register "uid" = "1"
				register "compat_string" = ""google,cros-ec-spi""
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A23_IRQ)"
				device spi 1 on end
			end # FPMCU
		end # GSPI #1
	end

end