chip soc/intel/apollolake

	# EMMC Tx CMD Delay
	# Refer to EDS-Vol2-16.32.
	# [14:8] steps of delay for DDR mode, each 125ps.
	# [6:0] steps of delay for SDR mode, each 125ps.
	register "emmc_tx_cmd_cntl" = "0x505"

	# EMMC TX DATA Delay 1
	# Refer to EDS-Vol2-16.33.
	# [14:8] steps of delay for HS400, each 125ps.
	# [6:0] steps of delay for SDR104/HS200, each 125ps.
	register "emmc_tx_data_cntl1" = "0x0b0d"

	# EMMC TX DATA Delay 2
	# Refer to EDS-Vol2-16.34.
	# [30:24] steps of delay for SDR50, each 125ps.
	# [22:16] steps of delay for DDR50, each 125ps.
	# [14:8] steps of delay for SDR25/HS50, each 125ps.
	# [6:0] steps of delay for SDR12, each 125ps.
	register "emmc_tx_data_cntl2" = "0x1c2a2a2a"

	# EMMC RX CMD/DATA Delay 1
	# Refer to EDS-Vol2-16.35.
	# [30:24] steps of delay for SDR50, each 125ps.
	# [22:16] steps of delay for DDR50, each 125ps.
	# [14:8] steps of delay for SDR25/HS50, each 125ps.
	# [6:0] steps of delay for SDR12, each 125ps.
	register "emmc_rx_cmd_data_cntl1" = "0x00171a1a"

	# EMMC RX CMD/DATA Delay 2
	# Refer to EDS-Vol2-16.37.
	# [17:16] stands for Rx Clock before Output Buffer
	# [14:8] steps of delay for Auto Tuning Mode, each 125ps.
	# [6:0] steps of delay for HS200, each 125ps.
	register "emmc_rx_cmd_data_cntl2" = "0x10028"

	# EMMC Rx Strobe Delay
	# Refer to EDS-Vol2-16.36.
	# [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps.
	# [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps.
	register "emmc_rx_strobe_cntl" = "0x0b0b"

        # Intel Common SoC Config
        #+-------------------+---------------------------+
        #| Field             |  Value                    |
        #+-------------------+---------------------------+
        #| GSPI0             | cr50 TPM. Early init is   |
        #|                   | required to set up a BAR  |
        #|                   | for TPM communication     |
        #|                   | before memory is up       |
        #+-------------------+---------------------------+
        register "common_soc_config" = "{
                .gspi[0] = {
                        .speed_mhz = 1,
                        .early_init = 1,
                },
        }"

	device domain 0 on
		device pci 16.0 off  end     # - I2C 0
		device pci 17.1 on
			chip drivers/i2c/da7219
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)"
				register "btn_cfg" = "50"
				register "mic_det_thr" = "500"
				register "jack_ins_deb" = "20"
				register "jack_det_rate" = ""32ms_64ms""
				register "jack_rem_deb" = "1"
				register "a_d_btn_thr" = "0xa"
				register "d_b_btn_thr" = "0x16"
				register "b_c_btn_thr" = "0x21"
				register "c_mic_btn_thr" = "0x3e"
				register "btn_avg" = "4"
				register "adc_1bit_rpt" = "1"
				register "micbias_lvl" = "2600"
				register "mic_amp_in_sel" = ""diff""
				device i2c 1a on end
			end
		end	# - I2C 5
		device pci 17.2 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPIO_135_IRQ)"
				register "wake" = "GPE0_DW3_27"
				register "probed" = "1"
				device i2c 15 on end
			end
		end	# - I2C 6
		device pci 17.3 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0001""
				register "desc" = ""ELAN Touchscreen""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_212_IRQ)"
				register "probed" = "1"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)"
				register "reset_delay_ms" = "20"
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)"
				register "enable_delay_ms" = "1"
				register "has_power_resource" = "1"
				device i2c 10 on end
			end
		end	# - I2C 7
	end

	# Disable compliance mode
	register "DisableComplianceMode" = "1"
end