uses HAVE_MP_TABLE uses CONFIG_ROMFS uses HAVE_PIRQ_TABLE uses USE_FALLBACK_IMAGE uses HAVE_FALLBACK_BOOT uses HAVE_HARD_RESET uses IRQ_SLOT_COUNT uses HAVE_OPTION_TABLE uses CONFIG_MAX_CPUS uses CONFIG_MAX_PHYSICAL_CPUS uses CONFIG_IOAPIC uses CONFIG_SMP uses FALLBACK_SIZE uses ROM_SIZE uses ROM_SECTION_SIZE uses ROM_IMAGE_SIZE uses ROM_SECTION_SIZE uses ROM_SECTION_OFFSET uses CONFIG_ROM_PAYLOAD uses CONFIG_ROM_PAYLOAD_START uses CONFIG_COMPRESSED_PAYLOAD_LZMA uses CONFIG_PRECOMPRESSED_PAYLOAD uses PAYLOAD_SIZE uses _ROMBASE uses XIP_ROM_SIZE uses XIP_ROM_BASE uses STACK_SIZE uses HEAP_SIZE uses USE_OPTION_TABLE uses LB_CKS_RANGE_START uses LB_CKS_RANGE_END uses LB_CKS_LOC uses MAINBOARD_PART_NUMBER uses MAINBOARD_VENDOR uses MAINBOARD uses COREBOOT_EXTRA_VERSION uses _RAMBASE uses TTYS0_BAUD uses TTYS0_BASE uses TTYS0_LCS uses DEFAULT_CONSOLE_LOGLEVEL uses MAXIMUM_CONSOLE_LOGLEVEL uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL uses CONFIG_CONSOLE_SERIAL8250 uses CROSS_COMPILE uses CC uses HOSTCC uses OBJCOPY uses CONFIG_CONSOLE_VGA uses CONFIG_PCI_ROM_RUN uses USE_DCACHE_RAM uses DCACHE_RAM_BASE uses DCACHE_RAM_SIZE uses CONFIG_USE_INIT uses CONFIG_USE_PRINTK_IN_CAR ### ### Build options ### ## ## ROM_SIZE is the size of boot ROM that this board will use. ## default ROM_SIZE=524288 ## ## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use ## default FALLBACK_SIZE=0x40000 ## ## Build code for the fallback boot ## default HAVE_FALLBACK_BOOT=1 ## ## Build code to reset the motherboard from coreboot ## default HAVE_HARD_RESET=1 ## ## Build code to export a programmable irq routing table ## default HAVE_PIRQ_TABLE=1 default IRQ_SLOT_COUNT=9 ## ## Build code to export an x86 MP table ## Useful for specifying IRQ routing values ## default HAVE_MP_TABLE=1 ## ## Build code to export a CMOS option table ## default HAVE_OPTION_TABLE=1 ## ## Move the default coreboot cmos range off of AMD RTC registers ## default LB_CKS_RANGE_START=49 default LB_CKS_RANGE_END=122 default LB_CKS_LOC=123 ## ## Build code for SMP support ## Only worry about 2 micro processors ## default CONFIG_SMP=1 default CONFIG_MAX_CPUS=2 default CONFIG_MAX_PHYSICAL_CPUS=2 ## ## Build code to setup a generic IOAPIC ## default CONFIG_IOAPIC=1 #VGA default CONFIG_CONSOLE_VGA=1 default CONFIG_PCI_ROM_RUN=1 ## ## enable CACHE_AS_RAM specifics ## default USE_DCACHE_RAM=1 default DCACHE_RAM_BASE=0xcf000 default DCACHE_RAM_SIZE=0x1000 default CONFIG_USE_INIT=0 ## ## Clean up the motherboard id strings ## default MAINBOARD_PART_NUMBER="E326" default MAINBOARD_VENDOR="IBM" #default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f #default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016 ### ### coreboot layout values ### ## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy. default ROM_IMAGE_SIZE = 65536 ## ## Use a small 8K stack ## default STACK_SIZE=0x2000 ## ## Use a small 16K heap ## default HEAP_SIZE=0x8000 ## ## Only use the option table in a normal image ## default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE ## ## Coreboot C code runs at this location in RAM ## default _RAMBASE=0x00004000 ## ## Load the payload from the ROM ## default CONFIG_ROM_PAYLOAD = 1 ### ### Defaults of options that you may want to override in the target config file ### ## ## The default compiler ## default CC="$(CROSS_COMPILE)gcc -m32" default HOSTCC="gcc" default CONFIG_USE_PRINTK_IN_CAR=1 ## ## The Serial Console ## # To Enable the Serial Console default CONFIG_CONSOLE_SERIAL8250=1 ## Select the serial console baud rate default TTYS0_BAUD=115200 #default TTYS0_BAUD=57600 #default TTYS0_BAUD=38400 #default TTYS0_BAUD=19200 #default TTYS0_BAUD=9600 #default TTYS0_BAUD=4800 #default TTYS0_BAUD=2400 #default TTYS0_BAUD=1200 # Select the serial console base port default TTYS0_BASE=0x3f8 # Select the serial protocol # This defaults to 8 data bits, 1 stop bit, and no parity default TTYS0_LCS=0x3 ## ### Select the coreboot loglevel ## ## EMERG 1 system is unusable ## ALERT 2 action must be taken immediately ## CRIT 3 critical conditions ## ERR 4 error conditions ## WARNING 5 warning conditions ## NOTICE 6 normal but significant condition ## INFO 7 informational ## DEBUG 8 debug-level messages ## SPEW 9 Way too many details ## Request this level of debugging output default DEFAULT_CONSOLE_LOGLEVEL=8 ## At a maximum only compile in this level of debugging default MAXIMUM_CONSOLE_LOGLEVEL=8 ## ## Select power on after power fail setting default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" ### End Options.lb # # ROMFS # # default CONFIG_ROMFS=0 end