uses CONFIG_GENERATE_MP_TABLE uses CONFIG_GENERATE_PIRQ_TABLE uses CONFIG_GENERATE_ACPI_TABLES uses CONFIG_HAVE_ACPI_RESUME uses CONFIG_ACPI_SSDTX_NUM uses CONFIG_USE_FALLBACK_IMAGE uses CONFIG_USE_FAILOVER_IMAGE uses CONFIG_HAVE_FALLBACK_BOOT uses CONFIG_HAVE_FAILOVER_BOOT uses CONFIG_HAVE_HARD_RESET uses CONFIG_IRQ_SLOT_COUNT uses CONFIG_HAVE_OPTION_TABLE uses CONFIG_MAX_CPUS uses CONFIG_MAX_PHYSICAL_CPUS uses CONFIG_LOGICAL_CPUS uses CONFIG_IOAPIC uses CONFIG_SMP uses CONFIG_FALLBACK_SIZE uses CONFIG_FAILOVER_SIZE uses CONFIG_ROM_SIZE uses CONFIG_ROM_SECTION_SIZE uses CONFIG_ROM_IMAGE_SIZE uses CONFIG_ROM_SECTION_SIZE uses CONFIG_ROM_SECTION_OFFSET uses CONFIG_ROM_PAYLOAD uses CONFIG_COMPRESSED_PAYLOAD_LZMA uses CONFIG_PRECOMPRESSED_PAYLOAD uses CONFIG_ROMBASE uses CONFIG_XIP_ROM_SIZE uses CONFIG_XIP_ROM_BASE uses CONFIG_STACK_SIZE uses CONFIG_HEAP_SIZE uses CONFIG_USE_OPTION_TABLE uses CONFIG_LB_CKS_RANGE_START uses CONFIG_LB_CKS_RANGE_END uses CONFIG_LB_CKS_LOC uses CONFIG_MAINBOARD_PART_NUMBER uses CONFIG_MAINBOARD_VENDOR uses CONFIG_MAINBOARD uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID uses COREBOOT_EXTRA_VERSION uses CONFIG_RAMBASE uses CONFIG_TTYS0_BAUD uses CONFIG_TTYS0_BASE uses CONFIG_TTYS0_LCS uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL uses CONFIG_CONSOLE_SERIAL8250 uses CONFIG_HAVE_INIT_TIMER uses CONFIG_GDB_STUB uses CONFIG_GDB_STUB uses CONFIG_CROSS_COMPILE uses CC uses HOSTCC uses CONFIG_OBJCOPY uses CONFIG_CONSOLE_VGA uses CONFIG_PCI_ROM_RUN uses CONFIG_HW_MEM_HOLE_SIZEK uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC uses CONFIG_K8_HT_FREQ_1G_SUPPORT uses CONFIG_HT_CHAIN_UNITID_BASE uses CONFIG_HT_CHAIN_END_UNITID_BASE uses CONFIG_SB_HT_CHAIN_ON_BUS0 uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY uses CONFIG_USE_DCACHE_RAM uses CONFIG_DCACHE_RAM_BASE uses CONFIG_DCACHE_RAM_SIZE uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE uses CONFIG_USE_INIT uses CONFIG_SERIAL_CPU_INIT uses CONFIG_ENABLE_APIC_EXT_ID uses CONFIG_APIC_ID_OFFSET uses CONFIG_LIFT_BSP_APIC_ID uses CONFIG_PCI_64BIT_PREF_MEM uses CONFIG_RAMTOP uses CONFIG_AP_CODE_IN_CAR uses CONFIG_MEM_TRAIN_SEQ uses CONFIG_WAIT_BEFORE_CPUS_INIT uses CONFIG_USE_PRINTK_IN_CAR ### ### Build options ### ## ## CONFIG_ROM_SIZE is the size of boot ROM that this board will use. ## default CONFIG_ROM_SIZE=524288 ## ## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use ## #FALLBACK: 256K-8K default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE #FAILOVER: 8K default CONFIG_FAILOVER_SIZE=0x02000 #more 1M for pgtbl default CONFIG_RAMTOP=2048*1024 ## ## Build code for the fallback boot ## default CONFIG_HAVE_FALLBACK_BOOT=1 default CONFIG_HAVE_FAILOVER_BOOT=1 ## ## Build code to reset the motherboard from coreboot ## default CONFIG_HAVE_HARD_RESET=1 ## ## Build code to export a programmable irq routing table ## default CONFIG_GENERATE_PIRQ_TABLE=1 default CONFIG_IRQ_SLOT_COUNT=11 ## ## Build code to export an x86 MP table ## Useful for specifying IRQ routing values ## default CONFIG_GENERATE_MP_TABLE=1 ## ACPI tables will be included default CONFIG_GENERATE_ACPI_TABLES=1 ## extra SSDT num default CONFIG_ACPI_SSDTX_NUM=3 ## ## Build code to export a CMOS option table ## default CONFIG_HAVE_OPTION_TABLE=1 ## ## Move the default coreboot cmos range off of AMD RTC registers ## default CONFIG_LB_CKS_RANGE_START=49 default CONFIG_LB_CKS_RANGE_END=122 default CONFIG_LB_CKS_LOC=123 ## ## Build code for SMP support ## Only worry about 2 micro processors ## default CONFIG_SMP=1 default CONFIG_MAX_CPUS=4 default CONFIG_MAX_PHYSICAL_CPUS=2 default CONFIG_LOGICAL_CPUS=1 default CONFIG_SERIAL_CPU_INIT=0 default CONFIG_ENABLE_APIC_EXT_ID=0 default CONFIG_APIC_ID_OFFSET=0x10 default CONFIG_LIFT_BSP_APIC_ID=1 #memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead. #2G #default CONFIG_HW_MEM_HOLE_SIZEK=0x200000 #1G #default CONFIG_HW_MEM_HOLE_SIZEK=0x100000 #512M default CONFIG_HW_MEM_HOLE_SIZEK=0x80000 #make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy #default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1 #Opteron K8 1G HT Support default CONFIG_K8_HT_FREQ_1G_SUPPORT=1 #VGA Console default CONFIG_CONSOLE_VGA=1 default CONFIG_PCI_ROM_RUN=1 #HT Unit ID offset, default is 1, the typical one default CONFIG_HT_CHAIN_UNITID_BASE=0xa #real SB Unit ID, default is 0x20, mean dont touch it at last default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6 #make the SB HT chain on bus 0, default is not (0) default CONFIG_SB_HT_CHAIN_ON_BUS0=2 #only offset for SB chain?, default is yes(1) #default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0 #allow capable device use that above 4G #default CONFIG_PCI_64BIT_PREF_MEM=1 ## ## enable CACHE_AS_RAM specifics ## default CONFIG_USE_DCACHE_RAM=1 default CONFIG_DCACHE_RAM_BASE=0xc4000 default CONFIG_DCACHE_RAM_SIZE=0x0c000 default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000 default CONFIG_USE_INIT=0 ## ## for rev F training on AP purpose ## #default CONFIG_AP_CODE_IN_CAR=1 #default CONFIG_MEM_TRAIN_SEQ=1 #default CONFIG_WAIT_BEFORE_CPUS_INIT=1 ## ## Build code to setup a generic IOAPIC ## default CONFIG_IOAPIC=1 ## ## Clean up the motherboard id strings ## default CONFIG_MAINBOARD_PART_NUMBER="dk8_htx" default CONFIG_MAINBOARD_VENDOR="IWILL" default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022 default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80 ### ### coreboot layout values ### ## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy. default CONFIG_ROM_IMAGE_SIZE = 65536 - CONFIG_FAILOVER_SIZE ## ## Use a small 8K stack ## default CONFIG_STACK_SIZE=0x2000 ## ## Use a small 32K heap ## default CONFIG_HEAP_SIZE=0x8000 ## ## Only use the option table in a normal image ## default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE ) ## ## Coreboot C code runs at this location in RAM ## default CONFIG_RAMBASE=0x00100000 ## ## Load the payload from the ROM ## default CONFIG_ROM_PAYLOAD = 1 ### ### Defaults of options that you may want to override in the target config file ### ## ## The default compiler ## default CC="$(CONFIG_CROSS_COMPILE)gcc -m32" default HOSTCC="gcc" ## ## Disable the gdb stub by default ## default CONFIG_GDB_STUB=0 ## ## The Serial Console ## default CONFIG_USE_PRINTK_IN_CAR=1 # To Enable the Serial Console default CONFIG_CONSOLE_SERIAL8250=1 ## Select the serial console baud rate default CONFIG_TTYS0_BAUD=115200 #default CONFIG_TTYS0_BAUD=57600 #default CONFIG_TTYS0_BAUD=38400 #default CONFIG_TTYS0_BAUD=19200 #default CONFIG_TTYS0_BAUD=9600 #default CONFIG_TTYS0_BAUD=4800 #default CONFIG_TTYS0_BAUD=2400 #default CONFIG_TTYS0_BAUD=1200 # Select the serial console base port default CONFIG_TTYS0_BASE=0x3f8 # Select the serial protocol # This defaults to 8 data bits, 1 stop bit, and no parity default CONFIG_TTYS0_LCS=0x3 ## ### Select the coreboot loglevel ## ## EMERG 1 system is unusable ## ALERT 2 action must be taken immediately ## CRIT 3 critical conditions ## ERR 4 error conditions ## WARNING 5 warning conditions ## NOTICE 6 normal but significant condition ## INFO 7 informational ## CONFIG_DEBUG 8 debug-level messages ## SPEW 9 Way too many details ## Request this level of debugging output default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8 ## At a maximum only compile in this level of debugging default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8 ## ## Select power on after power fail setting default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" ### End Options.lb end