/* * This file is part of the coreboot project. * * Copyright (C) 2011 Advanced Micro Devices, Inc. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; version 2 of the License. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ #include #include #include #include #include #include #include #include #include #include #include /* SMBUS0_BASE_ADDRESS */ #include #include "mainboard/lippert/frontrunner-af/sema.h" static void init(struct device *dev) { volatile u8 *spi_base; // base addr of Hudson's SPI host controller printk(BIOS_DEBUG, CONFIG_MAINBOARD_PART_NUMBER " ENTER %s\n", __func__); /* Init Hudson GPIOs. */ printk(BIOS_DEBUG, "Init FCH GPIOs @ 0x%08x\n", ACPI_MMIO_BASE+GPIO_BASE); FCH_IOMUX(50) = 2; // GPIO50: FCH_ARST#_GATE resets stuck PCIe devices FCH_GPIO (50) = 0xC0; // = output set to 1 as it's never needed FCH_IOMUX(197) = 2; // GPIO197: BIOS_DEFAULTS# FCH_GPIO (197) = 0x28; // = input, disable int. pull-up FCH_IOMUX(56) = 1; // GPIO58-56: REV_ID2-0 FCH_GPIO (56) = 0x28; // = inputs, disable int. pull-ups FCH_IOMUX(57) = 1; FCH_GPIO (57) = 0x28; FCH_IOMUX(58) = 1; FCH_GPIO (58) = 0x28; FCH_IOMUX(187) = 2; // GPIO187,188,166,GPO160: GPO0-3 on COM Express connector FCH_GPIO (187) = 0x08; // = outputs, disable PUs, default to 0 FCH_IOMUX(188) = 2; FCH_GPIO (188) = 0x08; FCH_IOMUX(166) = 2; FCH_GPIO (166) = 0x08; // needed to make GPO160 work (Hudson Register Reference section 2.3.6.1) FCH_PMIO(0xDC) &= ~0x80; FCH_PMIO(0xE6) = (FCH_PMIO(0xE6) & ~0x02) | 0x01; FCH_IOMUX(160) = 1; FCH_GPIO (160) = 0x08; FCH_IOMUX(189) = 1; // GPIO189-192: GPI0-3 on COM Express connector FCH_IOMUX(190) = 1; // default to inputs with int. PU FCH_IOMUX(191) = 1; FCH_IOMUX(192) = 1; if (!fch_gpio_state(197)) // just in case anyone cares printk(BIOS_INFO, "BIOS_DEFAULTS jumper is present.\n"); printk(BIOS_INFO, "Board revision ID: %u\n", fch_gpio_state(58)<<2 | fch_gpio_state(57)<<1 | fch_gpio_state(56)); /* Lower SPI speed from default 66 to 22 MHz for SST 25VF032B */ spi_base = (u8 *)((uintptr_t)pci_read_config32(pcidev_on_root(0x14, 3), 0xA0) & 0xFFFFFFE0); spi_base[0x0D] = (spi_base[0x0D] & ~0x30) | 0x20; // NormSpeed in SPI_Cntrl1 register /* Notify the SMC we're alive and kicking, or after a while it will * effect a power cycle and switch to the alternate BIOS chip. * Should be done as late as possible. * Failure here does not matter if watchdog was already disabled, * by configuration or previous boot, so ignore return value. */ sema_send_alive(); printk(BIOS_DEBUG, CONFIG_MAINBOARD_PART_NUMBER " EXIT %s\n", __func__); } /********************************************** * Enable the dedicated functions of the board. **********************************************/ static void mainboard_enable(struct device *dev) { printk(BIOS_INFO, "Mainboard " CONFIG_MAINBOARD_PART_NUMBER " Enable.\n"); dev->ops->init = init; /* enable GPP CLK0 thru CLK1 */ /* disable GPP CLK2 thru SLT_GFX_CLK */ u8 *misc_mem_clk_cntrl = (u8 *)(ACPI_MMIO_BASE + MISC_BASE); write8(misc_mem_clk_cntrl + 0, 0xFF); write8(misc_mem_clk_cntrl + 1, 0x00); write8(misc_mem_clk_cntrl + 2, 0x00); write8(misc_mem_clk_cntrl + 3, 0x00); write8(misc_mem_clk_cntrl + 4, 0x00); /* * Initialize ASF registers to an arbitrary address because someone * long ago set things up this way inside the SPD read code. The * SPD read code has been made generic and moved out of the board * directory, so the ASF init is being done here. */ pm_iowrite(0x29, 0x80); pm_iowrite(0x28, 0x61); } struct chip_operations mainboard_ops = { .enable_dev = mainboard_enable, };