config SOC_NVIDIA_TEGRA210
	bool
	default n
	select ARCH_BOOTBLOCK_ARMV4
	select ARCH_VERSTAGE_ARMV4
	select ARCH_ROMSTAGE_ARMV4
	select ARCH_RAMSTAGE_ARMV8_64
	select ARCH_ARM64_CPU_CORTEX_A57
	select ARCH_ARM64_CORTEX_A57_POWER_DOWN_SUPPORT
	select BOOTBLOCK_CONSOLE
	select GIC
	select HAVE_MONOTONIC_TIMER
	select GENERIC_UDELAY
	select HAVE_HARD_RESET
	select HAVE_UART_SPECIAL
	select HAVE_UART_MEMORY_MAPPED
	select EARLY_CONSOLE
	select ARM_BOOTBLOCK_CUSTOM
	select DYNAMIC_CBMEM
	select ARM64_USE_ARM_TRUSTED_FIRMWARE
	select HAS_PRECBMEM_TIMESTAMP_REGION
	select CHROMEOS_RAMOOPS_NON_ACPI
	select GENERIC_GPIO_LIB

if SOC_NVIDIA_TEGRA210

config MAINBOARD_DO_DSI_INIT
	bool "Use dsi graphics interface"
	depends on MAINBOARD_DO_NATIVE_VGA_INIT
	default n
	help
	  Initialize dsi display

config MAINBOARD_DO_SOR_INIT
	bool "Use dp graphics interface"
	depends on MAINBOARD_DO_NATIVE_VGA_INIT
	default n
	help
	  Initialize dp display

config BOOTBLOCK_CPU_INIT
	string
	default "soc/nvidia/tegra210/bootblock.c"
	help
	  CPU/SoC-specific bootblock code. This is useful if the
	  bootblock must load microcode or copy data from ROM before
	  searching for the bootblock.

config MAX_CPUS
	int
	default 4

choice CONSOLE_SERIAL_TEGRA210_UART_CHOICES
	prompt "Serial Console UART"
	default CONSOLE_SERIAL_TEGRA210_UARTA
	depends on CONSOLE_SERIAL_UART

config CONSOLE_SERIAL_TEGRA210_UARTA
	bool "UARTA"
	help
	  Serial console on UART A.

config CONSOLE_SERIAL_TEGRA210_UARTB
	bool "UARTB"
	help
	  Serial console on UART B.

config CONSOLE_SERIAL_TEGRA210_UARTC
	bool "UARTC"
	help
	  Serial console on UART C.

config CONSOLE_SERIAL_TEGRA210_UARTD
	bool "UARTD"
	help
	  Serial console on UART D.

config CONSOLE_SERIAL_TEGRA210_UARTE
	bool "UARTE"
	help
	  Serial console on UART E.

endchoice

config CONSOLE_SERIAL_TEGRA210_UART_ADDRESS
	hex
	depends on CONSOLE_SERIAL_UART
	default 0x70006000 if CONSOLE_SERIAL_TEGRA210_UARTA
	default 0x70006040 if CONSOLE_SERIAL_TEGRA210_UARTB
	default 0x70006200 if CONSOLE_SERIAL_TEGRA210_UARTC
	default 0x70006300 if CONSOLE_SERIAL_TEGRA210_UARTD
	default 0x70006400 if CONSOLE_SERIAL_TEGRA210_UARTE
	help
	  Map the UART names to the respective MMIO addres.

config BOOTROM_SDRAM_INIT
	bool "SoC BootROM does SDRAM init with full BCT"
	default n
	help
	  Use during Foster LPDDR4 bringup.

config TRUSTZONE_CARVEOUT_SIZE_MB
	hex "Size of Trust Zone region"
	default 0x14
	help
	  Size of Trust Zone area in MiB to reserve in memory map.

# Default to 700MHz. This value is based on nv bootloader setting.
config PLLX_KHZ
        int
        default 700000
endif

config HAVE_MTC
	bool "Add external Memory controller Training Code binary"
	default n
	depends on USE_BLOBS
	help
	  Select this option to add emc training firmware

if HAVE_MTC

config MTC_FILE
	string "tegra mtc firmware filename"
	default "tegra_mtc.bin"
	help
	  The filename of the mtc firmware

config MTC_DIRECTORY
	string "Directory where MTC firmware file is located"
	default "."
	help
	  Path to directory where MTC firmware file is located.

config MTC_ADDRESS
	hex
	default 0x81000000
	help
	  The DRAM location where MTC firmware to be loaded in. This location
	  needs to be consistent with the location defined in tegra_mtc.ld

endif # HAVE_MTC