/* SPDX-License-Identifier: GPL-2.0-only */ /* This file is part of the coreboot project. */ #include #include #include #include #include #include "chip.h" #include "i82801gx.h" #include "sata.h" typedef struct southbridge_intel_i82801gx_config config_t; static u8 get_ich7_sata_ports(void) { struct device *lpc; lpc = pcidev_on_root(31, 0); switch (pci_read_config16(lpc, PCI_DEVICE_ID)) { case 0x27b0: case 0x27b8: return 0xf; case 0x27b9: case 0x27bd: return 0x5; case 0x27bc: return 0x3; default: printk(BIOS_ERR, "i82801gx_sata: error: cannot determine port config\n"); return 0; } } void sata_enable(struct device *dev) { /* Get the chip configuration */ struct southbridge_intel_i82801gx_config *config = dev->chip_info; if (config->sata_mode == SATA_MODE_AHCI) { /* Check if the southbridge supports AHCI */ struct device *lpc_dev = pcidev_on_root(31, 0); if (!lpc_dev) { /* According to the PCI spec function 0 on a bus:device needs to be active for other functions to be enabled. Since SATA is on the same bus:device as the LPC bridge, it makes little sense to continue. */ die("Couldn't find the LPC device!\n"); } const bool ahci_supported = !(pci_read_config32(lpc_dev, FDVCT) & AHCI_UNSUPPORTED); if (!ahci_supported) { /* Fallback to IDE PLAIN for sata for the rest of the initialization */ config->sata_mode = SATA_MODE_IDE_PLAIN; printk(BIOS_DEBUG, "AHCI not supported, falling back to plain mode.\n"); } } if (config->sata_mode == SATA_MODE_AHCI) { /* Set map to ahci */ pci_write_config8(dev, SATA_MAP, (pci_read_config8(dev, SATA_MAP) & ~0xc3) | 0x40); } else { /* Set map to ide */ pci_write_config8(dev, SATA_MAP, pci_read_config8(dev, SATA_MAP) & ~0xc3); } /* At this point, the new pci id will appear on the bus */ } static void sata_init(struct device *dev) { u32 reg32; u16 reg16; u8 ports; /* Get the chip configuration */ config_t *config = dev->chip_info; printk(BIOS_DEBUG, "i82801gx_sata: initializing...\n"); if (config == NULL) { printk(BIOS_ERR, "i82801gx_sata: error: device not in devicetree.cb!\n"); return; } /* Get ICH7 SATA port config */ ports = get_ich7_sata_ports(); /* Enable BARs */ pci_write_config16(dev, PCI_COMMAND, 0x0007); switch (config->sata_mode) { case SATA_MODE_IDE_LEGACY_COMBINED: printk(BIOS_DEBUG, "SATA controller in combined mode.\n"); /* No AHCI: clear AHCI base */ pci_write_config32(dev, PCI_BASE_ADDRESS_5, 0x00000000); /* And without AHCI BAR no memory decoding */ reg16 = pci_read_config16(dev, PCI_COMMAND); reg16 &= ~PCI_COMMAND_MEMORY; pci_write_config16(dev, PCI_COMMAND, reg16); pci_write_config8(dev, 0x09, 0x80); /* Set timings */ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE | IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS); pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE | IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS | IDE_PPE0 | IDE_IE0 | IDE_TIME0); /* Sync DMA */ pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0); pci_write_config16(dev, IDE_SDMA_TIM, 0x0200); /* Set IDE I/O Configuration */ reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; pci_write_config32(dev, IDE_CONFIG, reg32); /* Combine IDE - SATA configuration */ pci_write_config8(dev, SATA_MAP, 0x02); /* Restrict ports - 0 and 2 only available */ ports &= 0x5; break; case SATA_MODE_AHCI: printk(BIOS_DEBUG, "SATA controller in AHCI mode.\n"); /* Allow both Legacy and Native mode */ pci_write_config8(dev, 0x09, 0x8f); /* Set Interrupt Line */ /* Interrupt Pin is set by D31IP.PIP */ pci_write_config8(dev, INTR_LN, 0x0a); struct resource *ahci_res = find_resource(dev, PCI_BASE_ADDRESS_5); if (ahci_res != NULL) /* write AHCI GHC_PI register */ write32(res2mmio(ahci_res, 0xc, 0), config->sata_ports_implemented); break; default: case SATA_MODE_IDE_PLAIN: printk(BIOS_DEBUG, "SATA controller in plain mode.\n"); /* Set Sata Controller Mode. No Mapping(?) */ pci_write_config8(dev, SATA_MAP, 0x00); /* No AHCI: clear AHCI base */ pci_write_config32(dev, PCI_BASE_ADDRESS_5, 0x00000000); /* And without AHCI BAR no memory decoding */ reg16 = pci_read_config16(dev, PCI_COMMAND); reg16 &= ~PCI_COMMAND_MEMORY; pci_write_config16(dev, PCI_COMMAND, reg16); /* Native mode capable on both primary and secondary (0xa) * or'ed with enabled (0x50) = 0xf */ pci_write_config8(dev, 0x09, 0x8f); /* Set Interrupt Line */ /* Interrupt Pin is set by D31IP.PIP */ pci_write_config8(dev, INTR_LN, 0xff); /* Set timings */ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE | IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS | IDE_PPE0 | IDE_IE0 | IDE_TIME0); pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE | IDE_SITRE | IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS | IDE_IE0 | IDE_TIME0); /* Sync DMA */ pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0 | IDE_PSDE0); pci_write_config16(dev, IDE_SDMA_TIM, 0x0201); /* Set IDE I/O Configuration */ reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; pci_write_config32(dev, IDE_CONFIG, reg32); break; } /* Set port control */ pci_write_config8(dev, SATA_PCS, ports); /* Enable clock gating for unused ports and set initialization reg */ pci_write_config32(dev, SATA_IR, SIF3(ports) | SIF2 | SIF1 | SCRE); /* All configurations need this SATA initialization sequence */ pci_write_config8(dev, 0xa0, 0x40); pci_write_config8(dev, 0xa6, 0x22); pci_write_config8(dev, 0xa0, 0x78); pci_write_config8(dev, 0xa6, 0x22); pci_write_config8(dev, 0xa0, 0x88); reg32 = pci_read_config32(dev, 0xa4); reg32 &= 0xc0c0c0c0; reg32 |= 0x1b1b1212; pci_write_config32(dev, 0xa4, reg32); pci_write_config8(dev, 0xa0, 0x8c); reg32 = pci_read_config32(dev, 0xa4); reg32 &= 0xc0c0ff00; reg32 |= 0x121200aa; pci_write_config32(dev, 0xa4, reg32); pci_write_config8(dev, 0xa0, 0x00); pci_write_config8(dev, PCI_INTERRUPT_LINE, 0); /* Sata Initialization Register */ reg32 = pci_read_config32(dev, SATA_IR); reg32 |= SCRD; // due to some bug pci_write_config32(dev, SATA_IR, reg32); } static struct pci_operations sata_pci_ops = { .set_subsystem = pci_dev_set_subsystem, }; static struct device_operations sata_ops = { .read_resources = pci_dev_read_resources, .set_resources = pci_dev_set_resources, .enable_resources = pci_dev_enable_resources, .init = sata_init, .scan_bus = 0, .enable = i82801gx_enable, .ops_pci = &sata_pci_ops, }; static const unsigned short sata_ids[] = { 0x27c0, /* Desktop Non-AHCI and Non-RAID Mode: 82801GB/GR/GDH (ICH7/ICH7R/ICH7DH) */ 0x27c1, /* Desktop AHCI Mode: 82801GB/GR/GDH (ICH7/ICH7R/ICH7DH) */ 0x27c4, /* Mobile Non-AHCI and Non-RAID Mode: 82801GBM/GHM (ICH7-M/ICH7-M DH) */ 0x27c5, /* Mobile AHCI Mode: 82801GBM/GHM (ICH7-M/ICH7-M DH) */ /* NOTE: Any of the below are not properly supported yet. */ 0x27c3, /* Desktop RAID mode: 82801GB/GR/GDH (ICH7/ICH7R/ICH7DH) */ 0x27c6, /* ICH7M DH Raid Mode: 82801GHM (ICH7-M DH) */ 0 }; static const struct pci_driver i82801gx_sata_driver __pci_driver = { .ops = &sata_ops, .vendor = PCI_VENDOR_ID_INTEL, .devices = sata_ids, };