/* SPDX-License-Identifier: GPL-2.0-only */ /* This file is part of the coreboot project. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "chip.h" #include "pch.h" #include "nvs.h" #include #include #include #define NMI_OFF 0 typedef struct southbridge_intel_ibexpeak_config config_t; /** * Set miscellanous static southbridge features. * * @param dev PCI device with I/O APIC control registers */ static void pch_enable_ioapic(struct device *dev) { u32 reg32; /* Enable ACPI I/O range decode */ pci_write_config8(dev, ACPI_CNTL, ACPI_EN); set_ioapic_id(VIO_APIC_VADDR, 0x01); /* affirm full set of redirection table entries ("write once") */ reg32 = io_apic_read(VIO_APIC_VADDR, 0x01); io_apic_write(VIO_APIC_VADDR, 0x01, reg32); /* * Select Boot Configuration register (0x03) and * use Processor System Bus (0x01) to deliver interrupts. */ io_apic_write(VIO_APIC_VADDR, 0x03, 0x01); } static void pch_enable_serial_irqs(struct device *dev) { /* Set packet length and toggle silent mode bit for one frame. */ pci_write_config8(dev, SERIRQ_CNTL, (1 << 7) | (1 << 6) | ((21 - 17) << 2) | (0 << 0)); #if !CONFIG(SERIRQ_CONTINUOUS_MODE) pci_write_config8(dev, SERIRQ_CNTL, (1 << 7) | (0 << 6) | ((21 - 17) << 2) | (0 << 0)); #endif } /* PIRQ[n]_ROUT[3:0] - PIRQ Routing Control * 0x00 - 0000 = Reserved * 0x01 - 0001 = Reserved * 0x02 - 0010 = Reserved * 0x03 - 0011 = IRQ3 * 0x04 - 0100 = IRQ4 * 0x05 - 0101 = IRQ5 * 0x06 - 0110 = IRQ6 * 0x07 - 0111 = IRQ7 * 0x08 - 1000 = Reserved * 0x09 - 1001 = IRQ9 * 0x0A - 1010 = IRQ10 * 0x0B - 1011 = IRQ11 * 0x0C - 1100 = IRQ12 * 0x0D - 1101 = Reserved * 0x0E - 1110 = IRQ14 * 0x0F - 1111 = IRQ15 * PIRQ[n]_ROUT[7] - PIRQ Routing Control * 0x80 - The PIRQ is not routed. */ static void pch_pirq_init(struct device *dev) { struct device *irq_dev; /* Interrupt 11 is not used by legacy devices and so can always be used for PCI interrupts. Full legacy IRQ routing is complicated and hard to get right. Fortunately all modern OS use MSI and so it's not that big of an issue anyway. Still we have to provide a reasonable default. Using interrupt 11 for it everywhere is a working default. ACPI-aware OS can move it to any interrupt and others will just leave them at default. */ const u8 pirq_routing = 11; pci_write_config8(dev, PIRQA_ROUT, pirq_routing); pci_write_config8(dev, PIRQB_ROUT, pirq_routing); pci_write_config8(dev, PIRQC_ROUT, pirq_routing); pci_write_config8(dev, PIRQD_ROUT, pirq_routing); pci_write_config8(dev, PIRQE_ROUT, pirq_routing); pci_write_config8(dev, PIRQF_ROUT, pirq_routing); pci_write_config8(dev, PIRQG_ROUT, pirq_routing); pci_write_config8(dev, PIRQH_ROUT, pirq_routing); for (irq_dev = all_devices; irq_dev; irq_dev = irq_dev->next) { u8 int_pin=0; if (!irq_dev->enabled || irq_dev->path.type != DEVICE_PATH_PCI) continue; int_pin = pci_read_config8(irq_dev, PCI_INTERRUPT_PIN); if (int_pin == 0) continue; pci_write_config8(irq_dev, PCI_INTERRUPT_LINE, pirq_routing); } } static void pch_gpi_routing(struct device *dev) { /* Get the chip configuration */ config_t *config = dev->chip_info; u32 reg32 = 0; /* An array would be much nicer here, or some * other method of doing this. */ reg32 |= (config->gpi0_routing & 0x03) << 0; reg32 |= (config->gpi1_routing & 0x03) << 2; reg32 |= (config->gpi2_routing & 0x03) << 4; reg32 |= (config->gpi3_routing & 0x03) << 6; reg32 |= (config->gpi4_routing & 0x03) << 8; reg32 |= (config->gpi5_routing & 0x03) << 10; reg32 |= (config->gpi6_routing & 0x03) << 12; reg32 |= (config->gpi7_routing & 0x03) << 14; reg32 |= (config->gpi8_routing & 0x03) << 16; reg32 |= (config->gpi9_routing & 0x03) << 18; reg32 |= (config->gpi10_routing & 0x03) << 20; reg32 |= (config->gpi11_routing & 0x03) << 22; reg32 |= (config->gpi12_routing & 0x03) << 24; reg32 |= (config->gpi13_routing & 0x03) << 26; reg32 |= (config->gpi14_routing & 0x03) << 28; reg32 |= (config->gpi15_routing & 0x03) << 30; pci_write_config32(dev, GPIO_ROUT, reg32); } static void pch_power_options(struct device *dev) { u8 reg8; u16 reg16, pmbase; u32 reg32; const char *state; /* Get the chip configuration */ config_t *config = dev->chip_info; int pwr_on = CONFIG_MAINBOARD_POWER_FAILURE_STATE; int nmi_option; /* Which state do we want to goto after g3 (power restored)? * 0 == S0 Full On * 1 == S5 Soft Off * * If the option is not existent (Laptops), use Kconfig setting. */ get_option(&pwr_on, "power_on_after_fail"); reg16 = pci_read_config16(dev, GEN_PMCON_3); reg16 &= 0xfffe; switch (pwr_on) { case MAINBOARD_POWER_OFF: reg16 |= 1; state = "off"; break; case MAINBOARD_POWER_ON: reg16 &= ~1; state = "on"; break; case MAINBOARD_POWER_KEEP: reg16 &= ~1; state = "state keep"; break; default: state = "undefined"; } reg16 &= ~(3 << 4); /* SLP_S4# Assertion Stretch 4s */ reg16 |= (1 << 3); /* SLP_S4# Assertion Stretch Enable */ reg16 &= ~(1 << 10); reg16 |= (1 << 11); /* SLP_S3# Min Assertion Width 50ms */ reg16 |= (1 << 12); /* Disable SLP stretch after SUS well */ pci_write_config16(dev, GEN_PMCON_3, reg16); printk(BIOS_INFO, "Set power %s after power failure.\n", state); /* Set up NMI on errors. */ reg8 = inb(0x61); reg8 &= 0x0f; /* Higher Nibble must be 0 */ reg8 &= ~(1 << 3); /* IOCHK# NMI Enable */ // reg8 &= ~(1 << 2); /* PCI SERR# Enable */ reg8 |= (1 << 2); /* PCI SERR# Disable for now */ outb(reg8, 0x61); reg8 = inb(0x70); nmi_option = NMI_OFF; get_option(&nmi_option, "nmi"); if (nmi_option) { printk(BIOS_INFO, "NMI sources enabled.\n"); reg8 &= ~(1 << 7); /* Set NMI. */ } else { printk(BIOS_INFO, "NMI sources disabled.\n"); reg8 |= (1 << 7); /* Can't mask NMI from PCI-E and NMI_NOW */ } outb(reg8, 0x70); /* Enable CPU_SLP# and Intel Speedstep, set SMI# rate down */ reg16 = pci_read_config16(dev, GEN_PMCON_1); reg16 &= ~(3 << 0); // SMI# rate 1 minute reg16 &= ~(1 << 10); // Disable BIOS_PCI_EXP_EN for native PME #if DEBUG_PERIODIC_SMIS /* Set DEBUG_PERIODIC_SMIS in pch.h to debug using * periodic SMIs. */ reg16 |= (3 << 0); // Periodic SMI every 8s #endif pci_write_config16(dev, GEN_PMCON_1, reg16); // Set the board's GPI routing. pch_gpi_routing(dev); pmbase = pci_read_config16(dev, 0x40) & 0xfffe; outl(config->gpe0_en, pmbase + GPE0_EN); outw(config->alt_gp_smi_en, pmbase + ALT_GP_SMI_EN); /* Set up power management block and determine sleep mode */ reg32 = inl(pmbase + 0x04); // PM1_CNT reg32 &= ~(7 << 10); // SLP_TYP reg32 |= (1 << 0); // SCI_EN outl(reg32, pmbase + 0x04); /* Clear magic status bits to prevent unexpected wake */ reg32 = RCBA32(PRSTS); reg32 |= (1 << 5) | (1 << 4) | (1 << 0); RCBA32(PRSTS) = reg32; /* FIXME: Does this even exist? */ reg32 = RCBA32(0x3f02); reg32 &= ~0xf; RCBA32(0x3f02) = reg32; } static void pch_rtc_init(struct device *dev) { u8 reg8; int rtc_failed; reg8 = pci_read_config8(dev, GEN_PMCON_3); rtc_failed = reg8 & RTC_BATTERY_DEAD; if (rtc_failed) { reg8 &= ~RTC_BATTERY_DEAD; pci_write_config8(dev, GEN_PMCON_3, reg8); elog_add_event(ELOG_TYPE_RTC_RESET); } printk(BIOS_DEBUG, "rtc_failed = 0x%x\n", rtc_failed); cmos_init(rtc_failed); } static void mobile5_pm_init(struct device *dev) { int i; printk(BIOS_DEBUG, "Mobile 5 PM init\n"); pci_write_config8(dev, 0xa9, 0x47); RCBA32 (0x1d44) = 0x00000000; (void) RCBA32 (0x1d44); RCBA32 (0x1d48) = 0x00030000; (void) RCBA32 (0x1d48); RCBA32 (0x1e80) = 0x000c0801; (void) RCBA32 (0x1e80); RCBA32 (0x1e84) = 0x000200f0; (void) RCBA32 (0x1e84); const u32 rcba2010[] = { /* 2010: */ 0x00188200, 0x14000016, 0xbc4abcb5, 0x00000000, /* 2020: */ 0xf0c9605b, 0x13683040, 0x04c8f16e, 0x09e90170 }; for (i = 0; i < sizeof(rcba2010) / sizeof(rcba2010[0]); i++) { RCBA32 (0x2010 + 4 * i) = rcba2010[i]; RCBA32 (0x2010 + 4 * i); } RCBA32 (0x2100) = 0x00000000; (void) RCBA32 (0x2100); RCBA32 (0x2104) = 0x00000757; (void) RCBA32 (0x2104); RCBA32 (0x2108) = 0x00170001; (void) RCBA32 (0x2108); RCBA32 (0x211c) = 0x00000000; (void) RCBA32 (0x211c); RCBA32 (0x2120) = 0x00010000; (void) RCBA32 (0x2120); RCBA32 (0x21fc) = 0x00000000; (void) RCBA32 (0x21fc); RCBA32 (0x2200) = 0x20000044; (void) RCBA32 (0x2200); RCBA32 (0x2204) = 0x00000001; (void) RCBA32 (0x2204); RCBA32 (0x2208) = 0x00003457; (void) RCBA32 (0x2208); const u32 rcba2210[] = { /* 2210 */ 0x00000000, 0x00000001, 0xa0fff210, 0x0000df00, /* 2220 */ 0x00e30880, 0x00000070, 0x00004000, 0x00000000, /* 2230 */ 0x00e30880, 0x00000070, 0x00004000, 0x00000000, /* 2240 */ 0x00002301, 0x36000000, 0x00010107, 0x00160000, /* 2250 */ 0x00001b01, 0x36000000, 0x00010107, 0x00160000, /* 2260 */ 0x00000601, 0x16000000, 0x00010107, 0x00160000, /* 2270 */ 0x00001c01, 0x16000000, 0x00010107, 0x00160000 }; for (i = 0; i < sizeof(rcba2210) / sizeof(rcba2210[0]); i++) { RCBA32 (0x2210 + 4 * i) = rcba2210[i]; RCBA32 (0x2210 + 4 * i); } const u32 rcba2300[] = { /* 2300: */ 0x00000000, 0x40000000, 0x4646827b, 0x6e803131, /* 2310: */ 0x32c77887, 0x00077733, 0x00007447, 0x00000040, /* 2320: */ 0xcccc0cfc, 0x0fbb0fff }; for (i = 0; i < sizeof(rcba2300) / sizeof(rcba2300[0]); i++) { RCBA32 (0x2300 + 4 * i) = rcba2300[i]; RCBA32 (0x2300 + 4 * i); } RCBA32 (0x37fc) = 0x00000000; (void) RCBA32 (0x37fc); RCBA32 (0x3dfc) = 0x00000000; (void) RCBA32 (0x3dfc); RCBA32 (0x3e7c) = 0xffffffff; (void) RCBA32 (0x3e7c); RCBA32 (0x3efc) = 0x00000000; (void) RCBA32 (0x3efc); RCBA32 (0x3f00) = 0x0000010b; (void) RCBA32 (0x3f00); } static void enable_hpet(void) { u32 reg32; /* Move HPET to default address 0xfed00000 and enable it */ reg32 = RCBA32(HPTC); reg32 |= (1 << 7); // HPET Address Enable reg32 &= ~(3 << 0); RCBA32(HPTC) = reg32; RCBA32(HPTC); /* Read back for it to work */ write32((u32 *)0xfed00010, read32((u32 *)0xfed00010) | 1); } static void enable_clock_gating(struct device *dev) { u32 reg32; u16 reg16; RCBA32_AND_OR(0x2234, ~0UL, 0xf); reg16 = pci_read_config16(dev, GEN_PMCON_1); reg16 |= (1 << 2) | (1 << 11); pci_write_config16(dev, GEN_PMCON_1, reg16); reg32 = RCBA32(CG); reg32 |= (1 << 31); reg32 |= (1 << 29) | (1 << 28); reg32 |= (1 << 27) | (1 << 26) | (1 << 25) | (1 << 24); reg32 |= (1 << 16); reg32 |= (1 << 17); reg32 |= (1 << 18); reg32 |= (1 << 22); reg32 |= (1 << 23); reg32 &= ~(1 << 20); reg32 |= (1 << 19); reg32 |= (1 << 0); reg32 |= (0xf << 1); RCBA32(CG) = reg32; RCBA32_OR(0x38c0, 0x7); RCBA32_OR(0x36d4, 0x6680c004); RCBA32_OR(0x3564, 0x3); } static void pch_set_acpi_mode(void) { if (!acpi_is_wakeup_s3() && CONFIG(HAVE_SMI_HANDLER)) { printk(BIOS_DEBUG, "Disabling ACPI via APMC:\n"); outb(APM_CNT_ACPI_DISABLE, APM_CNT); // Disable ACPI mode printk(BIOS_DEBUG, "done.\n"); } } static void pch_disable_smm_only_flashing(struct device *dev) { u8 reg8; printk(BIOS_SPEW, "Enabling BIOS updates outside of SMM... "); reg8 = pci_read_config8(dev, BIOS_CNTL); reg8 &= ~(1 << 5); pci_write_config8(dev, BIOS_CNTL, reg8); } static void pch_fixups(struct device *dev) { /* * Enable DMI ASPM in the PCH */ RCBA32_AND_OR(0x2304, ~(1 << 10), 0); RCBA32_OR(0x21a4, (1 << 11)|(1 << 10)); RCBA32_OR(0x21a8, 0x3); } static void lpc_init(struct device *dev) { printk(BIOS_DEBUG, "pch: lpc_init\n"); /* Set the value for PCI command register. */ pci_write_config16(dev, PCI_COMMAND, 0x000f); /* IO APIC initialization. */ pch_enable_ioapic(dev); pch_enable_serial_irqs(dev); /* Setup the PIRQ. */ pch_pirq_init(dev); /* Setup power options. */ pch_power_options(dev); /* Initialize power management */ mobile5_pm_init(dev); /* Set the state of the GPIO lines. */ //gpio_init(dev); /* Initialize the real time clock. */ pch_rtc_init(dev); /* Initialize ISA DMA. */ isa_dma_init(); /* Initialize the High Precision Event Timers, if present. */ enable_hpet(); /* Initialize Clock Gating */ enable_clock_gating(dev); setup_i8259(); /* The OS should do this? */ /* Interrupt 9 should be level triggered (SCI) */ i8259_configure_irq_trigger(9, 1); pch_disable_smm_only_flashing(dev); pch_set_acpi_mode(); pch_fixups(dev); } static void pch_lpc_read_resources(struct device *dev) { struct resource *res; config_t *config = dev->chip_info; u8 io_index = 0; /* Get the normal PCI resources of this device. */ pci_dev_read_resources(dev); /* Add an extra subtractive resource for both memory and I/O. */ res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0)); res->base = 0; res->size = 0x1000; res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED | IORESOURCE_FIXED; res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0)); res->base = 0xff800000; res->size = 0x00800000; /* 8 MB for flash */ res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED | IORESOURCE_FIXED; res = new_resource(dev, 3); /* IOAPIC */ res->base = IO_APIC_ADDR; res->size = 0x00001000; res->flags = IORESOURCE_MEM | IORESOURCE_ASSIGNED | IORESOURCE_FIXED; /* Set PCH IO decode ranges if required.*/ if ((config->gen1_dec & 0xFFFC) > 0x1000) { res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0)); res->base = config->gen1_dec & 0xFFFC; res->size = (config->gen1_dec >> 16) & 0xFC; res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED | IORESOURCE_FIXED; } if ((config->gen2_dec & 0xFFFC) > 0x1000) { res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0)); res->base = config->gen2_dec & 0xFFFC; res->size = (config->gen2_dec >> 16) & 0xFC; res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED | IORESOURCE_FIXED; } if ((config->gen3_dec & 0xFFFC) > 0x1000) { res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0)); res->base = config->gen3_dec & 0xFFFC; res->size = (config->gen3_dec >> 16) & 0xFC; res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED | IORESOURCE_FIXED; } if ((config->gen4_dec & 0xFFFC) > 0x1000) { res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0)); res->base = config->gen4_dec & 0xFFFC; res->size = (config->gen4_dec >> 16) & 0xFC; res->flags = IORESOURCE_IO| IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED | IORESOURCE_FIXED; } } static void pch_lpc_enable(struct device *dev) { /* Enable PCH Display Port */ RCBA16(DISPBDF) = 0x0010; RCBA32_OR(FD2, PCH_ENABLE_DBDF); pch_enable(dev); } static void southbridge_inject_dsdt(const struct device *dev) { global_nvs_t *gnvs = cbmem_add (CBMEM_ID_ACPI_GNVS, sizeof(*gnvs)); if (gnvs) { memset(gnvs, 0, sizeof(*gnvs)); acpi_create_gnvs(gnvs); gnvs->apic = 1; gnvs->mpen = 1; /* Enable Multi Processing */ gnvs->pcnt = dev_count_cpu(); /* And tell SMI about it */ smm_setup_structures(gnvs, NULL, NULL); /* Add it to SSDT. */ acpigen_write_scope("\\"); acpigen_write_name_dword("NVSA", (u32) gnvs); acpigen_pop_len(); } } void acpi_fill_fadt(acpi_fadt_t *fadt) { struct device *dev = pcidev_on_root(0x1f, 0); config_t *chip = dev->chip_info; u16 pmbase = pci_read_config16(dev, 0x40) & 0xfffe; int c2_latency; fadt->reserved = 0; fadt->sci_int = 0x9; fadt->smi_cmd = APM_CNT; fadt->acpi_enable = APM_CNT_ACPI_ENABLE; fadt->acpi_disable = APM_CNT_ACPI_DISABLE; fadt->s4bios_req = 0x0; fadt->pstate_cnt = 0; fadt->pm1a_evt_blk = pmbase; fadt->pm1b_evt_blk = 0x0; fadt->pm1a_cnt_blk = pmbase + 0x4; fadt->pm1b_cnt_blk = 0x0; fadt->pm2_cnt_blk = pmbase + 0x50; fadt->pm_tmr_blk = pmbase + 0x8; fadt->gpe0_blk = pmbase + 0x20; fadt->gpe1_blk = 0; fadt->pm1_evt_len = 4; fadt->pm1_cnt_len = 2; fadt->pm2_cnt_len = 1; fadt->pm_tmr_len = 4; fadt->gpe0_blk_len = 16; fadt->gpe1_blk_len = 0; fadt->gpe1_base = 0; fadt->cst_cnt = 0; c2_latency = chip->c2_latency; if (!c2_latency) { c2_latency = 101; /* c2 unsupported */ } fadt->p_lvl2_lat = c2_latency; fadt->p_lvl3_lat = 87; fadt->flush_size = 1024; fadt->flush_stride = 16; /* P_CNT not supported */ fadt->duty_offset = 0; fadt->duty_width = 0; fadt->day_alrm = 0xd; fadt->mon_alrm = 0x00; fadt->century = 0x32; fadt->iapc_boot_arch = ACPI_FADT_LEGACY_DEVICES | ACPI_FADT_8042; fadt->flags = ACPI_FADT_WBINVD | ACPI_FADT_C1_SUPPORTED | ACPI_FADT_SLEEP_BUTTON | ACPI_FADT_RESET_REGISTER | ACPI_FADT_S4_RTC_WAKE | ACPI_FADT_PLATFORM_CLOCK; if (chip->docking_supported) { fadt->flags |= ACPI_FADT_DOCKING_SUPPORTED; } if (c2_latency < 100) { fadt->flags |= ACPI_FADT_C2_MP_SUPPORTED; } fadt->reset_reg.space_id = 1; fadt->reset_reg.bit_width = 8; fadt->reset_reg.bit_offset = 0; fadt->reset_reg.access_size = ACPI_ACCESS_SIZE_BYTE_ACCESS; fadt->reset_reg.addrl = 0xcf9; fadt->reset_reg.addrh = 0; fadt->reset_value = 6; fadt->x_pm1a_evt_blk.space_id = 1; fadt->x_pm1a_evt_blk.bit_width = 32; fadt->x_pm1a_evt_blk.bit_offset = 0; fadt->x_pm1a_evt_blk.access_size = ACPI_ACCESS_SIZE_DWORD_ACCESS; fadt->x_pm1a_evt_blk.addrl = pmbase; fadt->x_pm1a_evt_blk.addrh = 0x0; fadt->x_pm1b_evt_blk.space_id = 1; fadt->x_pm1b_evt_blk.bit_width = 0; fadt->x_pm1b_evt_blk.bit_offset = 0; fadt->x_pm1b_evt_blk.access_size = 0; fadt->x_pm1b_evt_blk.addrl = 0x0; fadt->x_pm1b_evt_blk.addrh = 0x0; fadt->x_pm1a_cnt_blk.space_id = 1; fadt->x_pm1a_cnt_blk.bit_width = 16; fadt->x_pm1a_cnt_blk.bit_offset = 0; fadt->x_pm1a_cnt_blk.access_size = ACPI_ACCESS_SIZE_WORD_ACCESS; fadt->x_pm1a_cnt_blk.addrl = pmbase + 0x4; fadt->x_pm1a_cnt_blk.addrh = 0x0; fadt->x_pm1b_cnt_blk.space_id = 1; fadt->x_pm1b_cnt_blk.bit_width = 0; fadt->x_pm1b_cnt_blk.bit_offset = 0; fadt->x_pm1b_cnt_blk.access_size = 0; fadt->x_pm1b_cnt_blk.addrl = 0x0; fadt->x_pm1b_cnt_blk.addrh = 0x0; fadt->x_pm2_cnt_blk.space_id = 1; fadt->x_pm2_cnt_blk.bit_width = 8; fadt->x_pm2_cnt_blk.bit_offset = 0; fadt->x_pm2_cnt_blk.access_size = ACPI_ACCESS_SIZE_BYTE_ACCESS; fadt->x_pm2_cnt_blk.addrl = pmbase + 0x50; fadt->x_pm2_cnt_blk.addrh = 0x0; fadt->x_pm_tmr_blk.space_id = 1; fadt->x_pm_tmr_blk.bit_width = 32; fadt->x_pm_tmr_blk.bit_offset = 0; fadt->x_pm_tmr_blk.access_size = ACPI_ACCESS_SIZE_DWORD_ACCESS; fadt->x_pm_tmr_blk.addrl = pmbase + 0x8; fadt->x_pm_tmr_blk.addrh = 0x0; fadt->x_gpe0_blk.space_id = 1; fadt->x_gpe0_blk.bit_width = 128; fadt->x_gpe0_blk.bit_offset = 0; fadt->x_gpe0_blk.access_size = ACPI_ACCESS_SIZE_DWORD_ACCESS; fadt->x_gpe0_blk.addrl = pmbase + 0x20; fadt->x_gpe0_blk.addrh = 0x0; fadt->x_gpe1_blk.space_id = 1; fadt->x_gpe1_blk.bit_width = 0; fadt->x_gpe1_blk.bit_offset = 0; fadt->x_gpe1_blk.access_size = 0; fadt->x_gpe1_blk.addrl = 0x0; fadt->x_gpe1_blk.addrh = 0x0; } static const char *lpc_acpi_name(const struct device *dev) { return "LPCB"; } static void southbridge_fill_ssdt(const struct device *device) { struct device *dev = pcidev_on_root(0x1f, 0); config_t *chip = dev->chip_info; intel_acpi_pcie_hotplug_generator(chip->pcie_hotplug_map, 8); intel_acpi_gen_def_acpi_pirq(dev); } static void lpc_final(struct device *dev) { spi_finalize_ops(); /* Call SMM finalize() handlers before resume */ if (CONFIG(HAVE_SMI_HANDLER)) { if (CONFIG(INTEL_CHIPSET_LOCKDOWN) || acpi_is_wakeup_s3()) { outb(APM_CNT_FINALIZE, APM_CNT); } } } static struct pci_operations pci_ops = { .set_subsystem = pci_dev_set_subsystem, }; static struct device_operations device_ops = { .read_resources = pch_lpc_read_resources, .set_resources = pci_dev_set_resources, .enable_resources = pci_dev_enable_resources, .acpi_inject_dsdt = southbridge_inject_dsdt, .acpi_fill_ssdt = southbridge_fill_ssdt, .acpi_name = lpc_acpi_name, .write_acpi_tables = acpi_write_hpet, .init = lpc_init, .final = lpc_final, .enable = pch_lpc_enable, .scan_bus = scan_static_bus, .ops_pci = &pci_ops, }; static const unsigned short pci_device_ids[] = { PCI_DID_INTEL_IBEXPEAK_LPC_QM57, PCI_DID_INTEL_IBEXPEAK_LPC_HM55, 0 }; static const struct pci_driver pch_lpc __pci_driver = { .ops = &device_ops, .vendor = PCI_VENDOR_ID_INTEL, .devices = pci_device_ids, };