/* * This file is part of the coreboot project. * * Copyright (C) 2004-2005 Nick Barker * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ #include #include #include #include #include #include #include #include #include "rl5c476.h" #include "chip.h" static int enable_cf_boot = 0; static unsigned int cf_base; static void rl5c476_init(device_t dev) { pc16reg_t *pc16; unsigned char *base; /* cardbus controller function 1 for CF Socket */ printk(BIOS_DEBUG, "Ricoh RL5c476: Initializing.\n"); printk(BIOS_DEBUG, "CF Base = %0x\n",cf_base); /* misc control register */ pci_write_config16(dev,0x82,0x00a0); /* set up second slot as compact flash port if asked to do so */ if (!enable_cf_boot) { printk(BIOS_DEBUG, "CF boot not enabled.\n"); return; } if (PCI_FUNC(dev->path.pci.devfn) != 1) { // Only configure if second CF slot. return; } /* make sure isa interrupts are enabled */ pci_write_config16(dev,0x3e,0x0780); /* pick up where 16 bit card control structure is * (0x800 bytes into config structure) */ base = (unsigned char *)pci_read_config32(dev,0x10); pc16 = (pc16reg_t *)(base + 0x800); /* disable memory and io windows and turn off socket power */ pc16->pwctrl = 0; /* disable irq lines */ pc16->igctrl = 0; /* disable memory and I/O windows */ pc16->awinen = 0; /* reset card, configure for I/O and set IRQ line */ pc16->igctrl = 0x69; /* set io window 0 for 1e0 - 1ef */ /* NOTE: This now sets CF up on a contiguous I/O window of * 16 bytes, 0x1e0 to 0x1ef. * Be warned that this is not a standard IDE address as * automatically detected by the likes of FILO, and would need * patching to recognise these addresses as an IDE drive. * * An earlier version of this driver set up 2 I/O windows to * emulate the expected addresses for IDE2, however the PCMCIA * package within Linux then could not re-initialize the * device as it tried to take control of it. So I believe it is * easier to patch Filo or the like to pick up this drive * rather than playing silly games as the kernel tries to * boot. * * Nonetheless, FILO needs a special option enabled to boot * from this configuration, and it needs to clean up * afterwards. Please refer to FILO documentation and source * code for more details. */ pc16->iostl0 = 0xe0; pc16->iosth0 = 1; pc16->iospl0 = 0xef; pc16->iosph0 = 1; pc16->ioffl0 = 0; pc16->ioffh0 = 0; /* clear window 1 */ pc16->iostl1 = 0; pc16->iosth1 = 0; pc16->iospl1 = 0; pc16->iosph1 = 0; pc16->ioffl1 = 0x0; pc16->ioffh1 = 0; /* set up CF config window */ pc16->smpga0 = cf_base>>24; pc16->smsth0 = (cf_base>>20)&0x0f; pc16->smstl0 = (cf_base>>12)&0xff; pc16->smsph0 = ((cf_base>>20)&0x0f) | 0x80; pc16->smspl0 = (cf_base>>12)&0xff; pc16->moffl0 = 0; pc16->moffh0 = 0x40; /* set I/O width for Auto Data width */ pc16->ioctrl = 0x22; /* enable I/O window 0 and 1 */ pc16->awinen = 0xc1; pc16->miscc1 = 1; /* apply power and enable outputs */ pc16->pwctrl = 0xb0; // delay could be optimised, but this works udelay(100000); pc16->igctrl = 0x69; /* 16 bit CF always have first config byte at 0x200 into * Config structure, but CF+ may not according to spec - * should locate through reading tuple data, but this should * do for now. */ unsigned char *cptr; cptr = (unsigned char *)(cf_base + 0x200); printk(BIOS_DEBUG, "CF Config = %x\n",*cptr); /* Set CF to decode 16 IO bytes on any 16 byte boundary - * rely on the io windows of the bridge set up above to * map those bytes into the addresses for IDE controller 3 * (0x1e8 - 0x1ef and 0x3ed - 0x3ee) */ *cptr = 0x41; } void rl5c476_read_resources(device_t dev) { struct resource *resource; /* For CF socket we need an extra memory window for * the control structure of the CF itself */ if( enable_cf_boot && (PCI_FUNC(dev->path.pci.devfn) == 1)){ /* fake index as it isn't in PCI config space */ resource = new_resource(dev, 1); resource->flags |= IORESOURCE_MEM; resource->size = 0x1000; resource->align = resource->gran = 12; resource->limit= 0xffff0000; } cardbus_read_resources(dev); } void rl5c476_set_resources(device_t dev) { struct resource *resource; printk(BIOS_DEBUG, "%s In set resources \n",dev_path(dev)); if( enable_cf_boot && (PCI_FUNC(dev->path.pci.devfn) == 1)){ resource = find_resource(dev,1); if( !(resource->flags & IORESOURCE_STORED) ){ resource->flags |= IORESOURCE_STORED ; printk(BIOS_DEBUG, "%s 1 ==> %x\n", dev_path(dev), resource->base); cf_base = resource->base; } } pci_dev_set_resources(dev); } static struct device_operations ricoh_rl5c476_ops = { .read_resources = rl5c476_read_resources, .set_resources = rl5c476_set_resources, .enable_resources = cardbus_enable_resources, .init = rl5c476_init, .scan_bus = cardbus_scan_bridge, }; static const struct pci_driver ricoh_rl5c476_driver __pci_driver = { .ops = &ricoh_rl5c476_ops, .vendor = PCI_VENDOR_ID_RICOH, .device = PCI_DEVICE_ID_RICOH_RL5C476, }; void southbridge_init(device_t dev) { struct southbridge_ricoh_rl5c476_config *conf = dev->chip_info; enable_cf_boot = conf->enable_cf; } struct chip_operations southbridge_ricoh_rl5c476_ops = { CHIP_NAME("Ricoh RL5C476 CardBus Controller") .enable_dev = southbridge_init, };