/** @file
Copyright (c) 2018, Intel Corporation. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
This file is automatically generated. Please do NOT modify !!!
**/
#ifndef __FSPSUPD_H__
#define __FSPSUPD_H__
#include
#pragma pack(1)
///
/// Azalia Header structure
///
typedef struct {
UINT16 VendorId; ///< Codec Vendor ID
UINT16 DeviceId; ///< Codec Device ID
UINT8 RevisionId; ///< Revision ID of the codec. 0xFF matches any revision.
UINT8 SdiNum; ///< SDI number, 0xFF matches any SDI.
UINT16 DataDwords; ///< Number of data DWORDs pointed by the codec data buffer.
UINT32 Reserved; ///< Reserved for future use. Must be set to 0.
} AZALIA_HEADER;
///
/// Audio Azalia Verb Table structure
///
typedef struct {
AZALIA_HEADER Header; ///< AZALIA PCH header
UINT32 *Data; ///< Pointer to the data buffer. Its length is specified in the header
} AUDIO_AZALIA_VERB_TABLE;
///
/// Refer to the definition of PCH_INT_PIN
///
typedef enum {
SiPchNoInt, ///< No Interrupt Pin
SiPchIntA,
SiPchIntB,
SiPchIntC,
SiPchIntD
} SI_PCH_INT_PIN;
///
/// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device.
///
typedef struct {
UINT8 Device; ///< Device number
UINT8 Function; ///< Device function
UINT8 IntX; ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN)
UINT8 Irq; ///< IRQ to be set for device.
} SI_PCH_DEVICE_INTERRUPT_CONFIG;
#define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG 64 ///< Number of all PCH devices
/** Fsp S Configuration
**/
typedef struct {
/** Offset 0x0020 - Logo Pointer
Points to PEI Display Logo Image
**/
UINT32 LogoPtr;
/** Offset 0x0024 - Logo Size
Size of PEI Display Logo Image
**/
UINT32 LogoSize;
/** Offset 0x0028 - Graphics Configuration Ptr
Points to VBT
**/
UINT32 GraphicsConfigPtr;
/** Offset 0x002C - Enable Device 4
Enable/disable Device 4
$EN_DIS
**/
UINT8 Device4Enable;
/** Offset 0x002D - Enable HD Audio DSP
Enable/disable HD Audio DSP feature.
$EN_DIS
**/
UINT8 PchHdaDspEnable;
/** Offset 0x002E
**/
UINT8 UnusedUpdSpace0[3];
/** Offset 0x0031 - Enable eMMC Controller
Enable/disable eMMC Controller.
$EN_DIS
**/
UINT8 ScsEmmcEnabled;
/** Offset 0x0032 - Enable eMMC HS400 Mode
Enable eMMC HS400 Mode.
$EN_DIS
**/
UINT8 ScsEmmcHs400Enabled;
/** Offset 0x0033 - Enable SdCard Controller
Enable/disable SD Card Controller.
$EN_DIS
**/
UINT8 ScsSdCardEnabled;
/** Offset 0x0034 - Show SPI controller
Enable/disable to show SPI controller.
$EN_DIS
**/
UINT8 ShowSpiController;
/** Offset 0x0035
**/
UINT8 UnusedUpdSpace1[3];
/** Offset 0x0038 - MicrocodeRegionBase
Memory Base of Microcode Updates
**/
UINT32 MicrocodeRegionBase;
/** Offset 0x003C - MicrocodeRegionSize
Size of Microcode Updates
**/
UINT32 MicrocodeRegionSize;
/** Offset 0x0040 - Turbo Mode
Enable/Disable Turbo mode. 0: disable, 1: enable
$EN_DIS
**/
UINT8 TurboMode;
/** Offset 0x0041 - Enable SATA SALP Support
Enable/disable SATA Aggressive Link Power Management.
$EN_DIS
**/
UINT8 SataSalpSupport;
/** Offset 0x0042 - Enable SATA ports
Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1,
and so on.
**/
UINT8 SataPortsEnable[8];
/** Offset 0x004A - Enable SATA DEVSLP Feature
Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each
port, byte0 for port0, byte1 for port1, and so on.
**/
UINT8 SataPortsDevSlp[8];
/** Offset 0x0052 - Enable USB2 ports
Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for
port1, and so on.
**/
UINT8 PortUsb20Enable[16];
/** Offset 0x0062 - Enable USB3 ports
Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for
port1, and so on.
**/
UINT8 PortUsb30Enable[10];
/** Offset 0x006C - Enable xDCI controller
Enable/disable to xDCI controller.
$EN_DIS
**/
UINT8 XdciEnable;
/** Offset 0x006D
**/
UINT8 UnusedUpdSpace2[2];
/** Offset 0x006F - Enable SerialIo Device Mode
0:Disabled, 1:PCI Mode, 2:Acpi mode, 3:Hidden mode (Legacy UART mode) - Enable/disable
SerialIo I2C0,I2C1,I2C2,I2C3,I2C4,I2C5,SPI0,SPI1,SPI2,UART0,UART1,UART2 device
mode respectively. One byte for each controller, byte0 for I2C0, byte1 for I2C1,
and so on.
**/
UINT8 SerialIoDevMode[12];
/** Offset 0x007B - Address of PCH_DEVICE_INTERRUPT_CONFIG table.
The address of the table of PCH_DEVICE_INTERRUPT_CONFIG.
**/
UINT32 DevIntConfigPtr;
/** Offset 0x007F - Number of DevIntConfig Entry
Number of Device Interrupt Configuration Entry. If this is not zero, the DevIntConfigPtr
must not be NULL.
**/
UINT8 NumOfDevIntConfig;
/** Offset 0x0080 - PIRQx to IRQx Map Config
PIRQx to IRQx mapping. The valid value is 0x00 to 0x0F for each. First byte is for
PIRQA, second byte is for PIRQB, and so on. The setting is only available in Legacy
8259 PCI mode.
**/
UINT8 PxRcConfig[8];
/** Offset 0x0088 - Select GPIO IRQ Route
GPIO IRQ Select. The valid value is 14 or 15.
**/
UINT8 GpioIrqRoute;
/** Offset 0x0089 - Select SciIrqSelect
SCI IRQ Select. The valid value is 9, 10, 11, and 20, 21, 22, 23 for APIC only.
**/
UINT8 SciIrqSelect;
/** Offset 0x008A - Select TcoIrqSelect
TCO IRQ Select. The valid value is 9, 10, 11, 20, 21, 22, 23.
**/
UINT8 TcoIrqSelect;
/** Offset 0x008B - Enable/Disable Tco IRQ
Enable/disable TCO IRQ
$EN_DIS
**/
UINT8 TcoIrqEnable;
/** Offset 0x008C - PCH HDA Verb Table Entry Number
Number of Entries in Verb Table.
**/
UINT8 PchHdaVerbTableEntryNum;
/** Offset 0x008D - PCH HDA Verb Table Pointer
Pointer to Array of pointers to Verb Table.
**/
UINT32 PchHdaVerbTablePtr;
/** Offset 0x0091 - PCH HDA Codec Sx Wake Capability
Capability to detect wake initiated by a codec in Sx
**/
UINT8 PchHdaCodecSxWakeCapability;
/** Offset 0x0092 - Enable SATA
Enable/disable SATA controller.
$EN_DIS
**/
UINT8 SataEnable;
/** Offset 0x0093 - SATA Mode
Select SATA controller working mode.
0:AHCI, 1:RAID
**/
UINT8 SataMode;
/** Offset 0x0094 - USB Per Port HS Preemphasis Bias
USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port.
**/
UINT8 Usb2AfePetxiset[16];
/** Offset 0x00A4 - USB Per Port HS Transmitter Bias
USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port.
**/
UINT8 Usb2AfeTxiset[16];
/** Offset 0x00B4 - USB Per Port HS Transmitter Emphasis
USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON,
10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port.
**/
UINT8 Usb2AfePredeemp[16];
/** Offset 0x00C4 - USB Per Port Half Bit Pre-emphasis
USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis.
One byte for each port.
**/
UINT8 Usb2AfePehalfbit[16];
/** Offset 0x00D4 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment
Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value
in arrary can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxDeEmphEnable[10];
/** Offset 0x00DE - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting
USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16],
Default = 29h (approximately -3.5dB De-Emphasis). One byte for each port.
**/
UINT8 Usb3HsioTxDeEmph[10];
/** Offset 0x00E8 - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment
Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value
in arrary can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxDownscaleAmpEnable[10];
/** Offset 0x00F2 - USB 3.0 TX Output Downscale Amplitude Adjustment
USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], Default
= 00h. One byte for each port.
**/
UINT8 Usb3HsioTxDownscaleAmp[10];
/** Offset 0x00FC - Enable LAN
Enable/disable LAN controller.
$EN_DIS
**/
UINT8 PchLanEnable;
/** Offset 0x00FD - Enable HD Audio Link
Enable/disable HD Audio Link. Muxed with SSP0/SSP1/SNDW1.
$EN_DIS
**/
UINT8 PchHdaAudioLinkHda;
/** Offset 0x00FE - Enable HD Audio DMIC0 Link
Enable/disable HD Audio DMIC0 link. Muxed with SNDW4.
$EN_DIS
**/
UINT8 PchHdaAudioLinkDmic0;
/** Offset 0x00FF - Enable HD Audio DMIC1 Link
Enable/disable HD Audio DMIC1 link. Muxed with SNDW3.
$EN_DIS
**/
UINT8 PchHdaAudioLinkDmic1;
/** Offset 0x0100 - Enable HD Audio SSP0 Link
Enable/disable HD Audio SSP0/I2S link. Muxed with HDA.
$EN_DIS
**/
UINT8 PchHdaAudioLinkSsp0;
/** Offset 0x0101 - Enable HD Audio SSP1 Link
Enable/disable HD Audio SSP1/I2S link. Muxed with HDA/SNDW2.
$EN_DIS
**/
UINT8 PchHdaAudioLinkSsp1;
/** Offset 0x0102 - Enable HD Audio SSP2 Link
Enable/disable HD Audio SSP2/I2S link.
$EN_DIS
**/
UINT8 PchHdaAudioLinkSsp2;
/** Offset 0x0103 - Enable HD Audio SoundWire#1 Link
Enable/disable HD Audio SNDW1 link. Muxed with HDA.
$EN_DIS
**/
UINT8 PchHdaAudioLinkSndw1;
/** Offset 0x0104 - Enable HD Audio SoundWire#2 Link
Enable/disable HD Audio SNDW2 link. Muxed with SSP1.
$EN_DIS
**/
UINT8 PchHdaAudioLinkSndw2;
/** Offset 0x0105 - Enable HD Audio SoundWire#3 Link
Enable/disable HD Audio SNDW3 link. Muxed with DMIC1.
$EN_DIS
**/
UINT8 PchHdaAudioLinkSndw3;
/** Offset 0x0106 - Enable HD Audio SoundWire#4 Link
Enable/disable HD Audio SNDW4 link. Muxed with DMIC0.
$EN_DIS
**/
UINT8 PchHdaAudioLinkSndw4;
/** Offset 0x0107 - Soundwire Clock Buffer GPIO RCOMP Setting
0: non-ACT - 50 Ohm driver impedance, 1: ACT - 8 Ohm driver impedance.
$EN_DIS
**/
UINT8 PchHdaSndwBufferRcomp;
/** Offset 0x0108 - PTM for PCIE RP Mask
Enable/disable Precision Time Measurement for PCIE Root Ports. 0: disable, 1: enable.
One bit for each port, bit0 for port1, bit1 for port2, and so on.
**/
UINT32 PcieRpPtmMask;
/** Offset 0x010C - DPC for PCIE RP Mask
Enable/disable Downstream Port Containment for PCIE Root Ports. 0: disable, 1: enable.
One bit for each port, bit0 for port1, bit1 for port2, and so on.
**/
UINT32 PcieRpDpcMask;
/** Offset 0x0110 - DPC Extensions PCIE RP Mask
Enable/disable DPC Extensions for PCIE Root Ports. 0: disable, 1: enable. One bit
for each port, bit0 for port1, bit1 for port2, and so on.
**/
UINT32 PcieRpDpcExtensionsMask;
/** Offset 0x0114 - USB PDO Programming
Enable/disable PDO programming for USB in PEI phase. Disabling will allow for programming
during later phase. 1: enable, 0: disable
$EN_DIS
**/
UINT8 UsbPdoProgramming;
/** Offset 0x0115 - Power button debounce configuration
Debounce time for PWRBTN in microseconds. For values not supported by HW, they will
be rounded down to closest supported on. 0: disable, 250-1024000us: supported range
**/
UINT32 PmcPowerButtonDebounce;
/** Offset 0x0119 - PCH eSPI Master and Slave BME enabled
PCH eSPI Master and Slave BME enabled
$EN_DIS
**/
UINT8 PchEspiBmeMasterSlaveEnabled;
/** Offset 0x011A - PCH SATA use RST Legacy OROM
Use PCH SATA RST Legacy OROM when CSM is Enabled
$EN_DIS
**/
UINT8 SataRstLegacyOrom;
/** Offset 0x011B - Trace Hub Memory Base
If Trace Hub is enabled and trace to memory is desired, BootLoader needs to allocate
trace hub memory as reserved and uncacheable, set the base to ensure Trace Hub
memory is configured properly.
**/
UINT32 TraceHubMemBase;
/** Offset 0x011F - PMC Debug Message Enable
When Enabled, PMC HW will send debug messages to trace hub; When Disabled, PMC HW
will never send debug meesages to trace hub. Noted: When Enabled, may not enter S0ix
$EN_DIS
**/
UINT8 PmcDbgMsgEn;
/** Offset 0x0120 - Pointer of ChipsetInit Binary
ChipsetInit Binary Pointer.
**/
UINT32 ChipsetInitBinPtr;
/** Offset 0x0124 - Length of ChipsetInit Binary
ChipsetInit Binary Length.
**/
UINT32 ChipsetInitBinLen;
/** Offset 0x0128 - PchPostMemRsvd
Reserved for PCH Post-Mem
$EN_DIS
**/
UINT8 PchPostMemRsvd[29];
/** Offset 0x0145 - Enable Ufs Controller
Enable/disable Ufs 2.0 Controller.
$EN_DIS
**/
UINT8 ScsUfsEnabled;
/** Offset 0x0146 - CNVi Configuration
This option allows for automatic detection of Connectivity Solution. [Auto Detection]
assumes that CNVi will be enabled when available, [Disable] allows for disabling CNVi.
0:Disable, 1:Auto
**/
UINT8 PchCnviMode;
/** Offset 0x0147 - SdCard power enable polarity
Choose SD_PWREN# polarity
0: Active low, 1: Active high
**/
UINT8 SdCardPowerEnableActiveHigh;
/** Offset 0x0148 - PCH USB2 PHY Power Gating enable
1: Will enable USB2 PHY SUS Well Power Gating, 0: Will not enable PG of USB2 PHY
Sus Well PG
$EN_DIS
**/
UINT8 PchUsb2PhySusPgEnable;
/** Offset 0x0149 - PCH USB OverCurrent mapping enable
1: Will program USB OC pin mapping in xHCI controller memory, 0: Will clear OC pin
mapping allow for NOA usage of OC pins
$EN_DIS
**/
UINT8 PchUsbOverCurrentEnable;
/** Offset 0x014A
**/
UINT8 UnusedUpdSpace3;
/** Offset 0x014B - CNVi MfUart1 Type
This option configures Uart type which connects to MfUart1
0:ISH Uart0, 1:SerialIO Uart2, 2:Uart over external pads
**/
UINT8 PchCnviMfUart1Type;
/** Offset 0x014C - Espi Lgmr Memory Range decode
This option enables or disables espi lgmr
$EN_DIS
**/
UINT8 PchEspiLgmrEnable;
/** Offset 0x014D - HECI3 state
The HECI3 state from Mbp for reference in S3 path or when MbpHob is not installed.
0: disable, 1: enable
$EN_DIS
**/
UINT8 Heci3Enabled;
/** Offset 0x014E
**/
UINT8 UnusedUpdSpace4;
/** Offset 0x014F - PCHHOT# pin
Enable PCHHOT# pin assertion when temperature is higher than PchHotLevel. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PchHotEnable;
/** Offset 0x0150 - SATA LED
SATA LED indicating SATA controller activity. 0: disable, 1: enable
$EN_DIS
**/
UINT8 SataLedEnable;
/** Offset 0x0151 - VRAlert# Pin
When VRAlert# feature pin is enabled and its state is '0', the PMC requests throttling
to a T3 Tstate to the PCH throttling unit.. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PchPmVrAlert;
/** Offset 0x0152 - SLP_S0 VM Dynamic Control
SLP_S0 Voltage Margining Runtime Control Policy. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PchPmSlpS0VmRuntimeControl;
/** Offset 0x0153 - SLP_S0 VM 0.70V Support
SLP_S0 Voltage Margining 0.70V Support Policy. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PchPmSlpS0Vm070VSupport;
/** Offset 0x0154 - SLP_S0 VM 0.75V Support
SLP_S0 Voltage Margining 0.75V Support Policy. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PchPmSlpS0Vm075VSupport;
/** Offset 0x0155 - AMT Switch
Enable/Disable. 0: Disable, 1: enable, Enable or disable AMT functionality.
$EN_DIS
**/
UINT8 AmtEnabled;
/** Offset 0x0156 - WatchDog Timer Switch
Enable/Disable. 0: Disable, 1: enable, Enable or disable WatchDog timer.
$EN_DIS
**/
UINT8 WatchDog;
/** Offset 0x0157 - ASF Switch
Enable/Disable. 0: Disable, 1: enable, Enable or disable ASF functionality.
$EN_DIS
**/
UINT8 AsfEnabled;
/** Offset 0x0158 - Manageability Mode set by Mebx
Enable/Disable. 0: Disable, 1: enable, Enable or disable Manageability Mode.
$EN_DIS
**/
UINT8 ManageabilityMode;
/** Offset 0x0159 - PET Progress
Enable/Disable. 0: Disable, 1: enable, Enable/Disable PET Events Progress to receive
PET Events.
$EN_DIS
**/
UINT8 FwProgress;
/** Offset 0x015A - SOL Switch
Enable/Disable. 0: Disable, 1: enable, Serial Over Lan enable/disable state by Mebx
$EN_DIS
**/
UINT8 AmtSolEnabled;
/** Offset 0x015B - OS Timer
16 bits Value, Set OS watchdog timer.
$EN_DIS
**/
UINT16 WatchDogTimerOs;
/** Offset 0x015D - BIOS Timer
16 bits Value, Set BIOS watchdog timer.
$EN_DIS
**/
UINT16 WatchDogTimerBios;
/** Offset 0x015F - Remote Assistance Trigger Availablilty
Enable/Disable. 0: Disable, 1: enable, Remote Assistance enable/disable state by Mebx
$EN_DIS
**/
UINT8 RemoteAssistance;
/** Offset 0x0160 - KVM Switch
Enable/Disable. 0: Disable, 1: enable, KVM enable/disable state by Mebx
$EN_DIS
**/
UINT8 AmtKvmEnabled;
/** Offset 0x0161 - MEBX execution
Enable/Disable. 0: Disable, 1: enable, Force MEBX execution
$EN_DIS
**/
UINT8 ForcMebxSyncUp;
/** Offset 0x0162
**/
UINT8 UnusedUpdSpace5[1];
/** Offset 0x0163 - PCH PCIe root port connection type
0: built-in device, 1:slot
**/
UINT8 PcieRpSlotImplemented[24];
/** Offset 0x017B - Usage type for ClkSrc
0-23: PCH rootport, 0x40-0x43: PEG port, 0x70:LAN, 0x80: unspecified but in use
(free running), 0xFF: not used
**/
UINT8 PcieClkSrcUsage[16];
/** Offset 0x018B - ClkReq-to-ClkSrc mapping
Number of ClkReq signal assigned to ClkSrc
**/
UINT8 PcieClkSrcClkReq[16];
/** Offset 0x019B - PCIE RP Access Control Services Extended Capability
Enable/Disable PCIE RP Access Control Services Extended Capability
**/
UINT8 PcieRpAcsEnabled[24];
/** Offset 0x01B3 - PCIE RP Clock Power Management
Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal
can still be controlled by L1 PM substates mechanism
**/
UINT8 PcieRpEnableCpm[24];
/** Offset 0x01CB - PCIE RP Detect Timeout Ms
The number of milliseconds within 0~65535 in reference code will wait for link to
exit Detect state for enabled ports before assuming there is no device and potentially
disabling the port.
**/
UINT16 PcieRpDetectTimeoutMs[24];
/** Offset 0x01FB - ModPHY SUS Power Domain Dynamic Gating
Enable/Disable ModPHY SUS Power Domain Dynamic Gating. Setting not supported on
PCH-H. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PmcModPhySusPgEnable;
/** Offset 0x01FC - SlpS0WithGbeSupport
Enable/Disable SLP_S0 with GBE Support. 0: disable, 1: enable
$EN_DIS
**/
UINT8 SlpS0WithGbeSupport;
/** Offset 0x01FD
**/
UINT8 UnusedUpdSpace6[3];
/** Offset 0x0200 - Enable/Disable SA CRID
Enable: SA CRID, Disable (Default): SA CRID
$EN_DIS
**/
UINT8 CridEnable;
/** Offset 0x0201 - DMI ASPM
0=Disable, 1:L0s, 2:L1, 3(Default)=L0sL1
0:Disable, 1:L0s, 2:L1, 3:L0sL1
**/
UINT8 DmiAspm;
/** Offset 0x0202 - PCIe DeEmphasis control per root port
0: -6dB, 1(Default): -3.5dB
0:-6dB, 1:-3.5dB
**/
UINT8 PegDeEmphasis[4];
/** Offset 0x0206 - PCIe Slot Power Limit value per root port
Slot power limit value per root port
**/
UINT8 PegSlotPowerLimitValue[4];
/** Offset 0x020A - PCIe Slot Power Limit scale per root port
Slot power limit scale per root port
0:1.0x, 1:0.1x, 2:0.01x, 3:0x001x
**/
UINT8 PegSlotPowerLimitScale[4];
/** Offset 0x020E - PCIe Physical Slot Number per root port
Physical Slot Number per root port
**/
UINT16 PegPhysicalSlotNumber[4];
/** Offset 0x0216 - Enable/Disable PavpEnable
Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable
$EN_DIS
**/
UINT8 PavpEnable;
/** Offset 0x0217 - CdClock Frequency selection
0=337.5 Mhz, 1=450 Mhz, 2=540 Mhz, 3(Default)=675 Mhz
0: 337.5 Mhz, 1: 450 Mhz, 2: 540 Mhz, 3: 675 Mhz
**/
UINT8 CdClock;
/** Offset 0x0218 - Enable/Disable PeiGraphicsPeimInit
Enable: Enable PeiGraphicsPeimInit, Disable(Default): Disable PeiGraphicsPeimInit
$EN_DIS
**/
UINT8 PeiGraphicsPeimInit;
/** Offset 0x0219
**/
UINT8 UnusedUpdSpace7;
/** Offset 0x021A - Enable or disable GNA device
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 GnaEnable;
/** Offset 0x021B - State of X2APIC_OPT_OUT bit in the DMAR table
0=Disable/Clear, 1=Enable/Set
$EN_DIS
**/
UINT8 X2ApicOptOut;
/** Offset 0x021C - Base addresses for VT-d function MMIO access
Base addresses for VT-d MMIO access per VT-d engine
**/
UINT32 VtdBaseAddress[3];
/** Offset 0x0228 - Enable or disable eDP device
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortEdp;
/** Offset 0x0229 - Enable or disable HPD of DDI port B
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortBHpd;
/** Offset 0x022A - Enable or disable HPD of DDI port C
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortCHpd;
/** Offset 0x022B - Enable or disable HPD of DDI port D
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortDHpd;
/** Offset 0x022C - Enable or disable HPD of DDI port F
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortFHpd;
/** Offset 0x022D - Enable or disable DDC of DDI port B
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortBDdc;
/** Offset 0x022E - Enable or disable DDC of DDI port C
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortCDdc;
/** Offset 0x022F - Enable or disable DDC of DDI port D
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortDDdc;
/** Offset 0x0230 - Enable or disable DDC of DDI port F
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPortFDdc;
/** Offset 0x0231 - Enable/Disable SkipS3CdClockInit
Enable: Skip Full CD clock initializaton, Disable(Default): Initialize the full
CD clock in S3 resume due to GOP absent
$EN_DIS
**/
UINT8 SkipS3CdClockInit;
/** Offset 0x0232 - Delta T12 Power Cycle Delay required in ms
Select the value for delay required. 0(Default)= No delay, 0xFFFF = Auto calculate
T12 Delay to max 500ms
0 : No Delay, 0xFFFF : Auto Calulate T12 Delay
**/
UINT16 DeltaT12PowerCycleDelay;
/** Offset 0x0234 - Blt Buffer Address
Address of Blt buffer
**/
UINT32 BltBufferAddress;
/** Offset 0x0238 - Blt Buffer Size
Size of Blt Buffer, is equal to PixelWidth * PixelHeight * 4 bytes (the size of
EFI_GRAPHICS_OUTPUT_BLT_PIXEL)
**/
UINT32 BltBufferSize;
/** Offset 0x023C - SaPostMemProductionRsvd
Reserved for SA Post-Mem Production
$EN_DIS
**/
UINT8 SaPostMemProductionRsvd[35];
/** Offset 0x025F - PCIE RP Disable Gen2PLL Shutdown and L1 Clock Gating Enable
PCIE RP Disable Gen2PLL Shutdown and L1 Clock Gating Enable Workaround needed for
Alpine ridge
**/
UINT8 PcieRootPortGen2PllL1CgDisable[24];
/** Offset 0x0277 - Advanced Encryption Standard (AES) feature
Enable or Disable Advanced Encryption Standard (AES) feature; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 AesEnable;
/** Offset 0x0278 - Power State 3 enable/disable
PCODE MMIO Mailbox: Power State 3 enable/disable; 0: Disable; 1: Enable.
For all VR Indexes
**/
UINT8 Psi3Enable[5];
/** Offset 0x027D - Power State 4 enable/disable
PCODE MMIO Mailbox: Power State 4 enable/disable; 0: Disable; 1: Enable.For
all VR Indexes
**/
UINT8 Psi4Enable[5];
/** Offset 0x0282 - Imon slope correction
PCODE MMIO Mailbox: Imon slope correction. Specified in 1/100 increment values.
Range is 0-200. 125 = 1.25. 0: Auto.For all VR Indexes
**/
UINT8 ImonSlope[5];
/** Offset 0x0287 - Imon offset correction
PCODE MMIO Mailbox: Imon offset correction. Value is a 2's complement signed integer.
Units 1/1000, Range 0-63999. For an offset = 12.580, use 12580. 0: Auto
**/
UINT8 ImonOffset[5];
/** Offset 0x028C - Enable/Disable BIOS configuration of VR
Enable/Disable BIOS configuration of VR; 0: Disable; 1: Enable.For all VR Indexes
**/
UINT8 VrConfigEnable[5];
/** Offset 0x0291 - Thermal Design Current enable/disable
PCODE MMIO Mailbox: Thermal Design Current enable/disable; 0: Disable; 1:
Enable.For all VR Indexes
**/
UINT8 TdcEnable[5];
/** Offset 0x0296 - HECI3 state
PCODE MMIO Mailbox: Thermal Design Current time window. Defined in milli seconds.
Valid Values 1 - 1ms , 2 - 2ms , 3 - 3ms , 4 - 4ms , 5 - 5ms , 6 - 6ms , 7 - 7ms
, 8 - 8ms , 10 - 10ms.For all VR Indexe
**/
UINT8 TdcTimeWindow[5];
/** Offset 0x029B - Thermal Design Current Lock
PCODE MMIO Mailbox: Thermal Design Current Lock; 0: Disable; 1: Enable.For
all VR Indexes
**/
UINT8 TdcLock[5];
/** Offset 0x02A0 - Platform Psys slope correction
PCODE MMIO Mailbox: Platform Psys slope correction. 0 - Auto Specified in
1/100 increment values. Range is 0-200. 125 = 1.25
**/
UINT8 PsysSlope;
/** Offset 0x02A1 - Platform Psys offset correction
PCODE MMIO Mailbox: Platform Psys offset correction. 0 - Auto Units 1/4,
Range 0-255. Value of 100 = 100/4 = 25 offset
**/
UINT8 PsysOffset;
/** Offset 0x02A2 - Acoustic Noise Mitigation feature
Enable or Disable Acoustic Noise Mitigation feature. This has to be enabled to program
slew rate configuration for all VR domains, Pre Wake, Ramp Up and, Ramp Down times.0:
Disabled; 1: Enabled
$EN_DIS
**/
UINT8 AcousticNoiseMitigation;
/** Offset 0x02A3 - Disable Fast Slew Rate for Deep Package C States for VR IA domain
Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
feature enabled. 0: False; 1: True
$EN_DIS
**/
UINT8 FastPkgCRampDisableIa;
/** Offset 0x02A4 - Slew Rate configuration for Deep Package C States for VR IA domain
Slew Rate configuration for Deep Package C States for VR IA domain based on Acoustic
Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16
0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
UINT8 SlowSlewRateForIa;
/** Offset 0x02A5 - Slew Rate configuration for Deep Package C States for VR GT domain
Slew Rate configuration for Deep Package C States for VR GT domain based on Acoustic
Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16
0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
UINT8 SlowSlewRateForGt;
/** Offset 0x02A6 - Slew Rate configuration for Deep Package C States for VR SA domain
Slew Rate configuration for Deep Package C States for VR SA domain based on Acoustic
Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16
0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
UINT8 SlowSlewRateForSa;
/** Offset 0x02A7 - Thermal Design Current current limit
PCODE MMIO Mailbox: Thermal Design Current current limit. Specified in 1/8A units.
Range is 0-4095. 1000 = 125A. 0: Auto. For all VR Indexes
**/
UINT16 TdcPowerLimit[5];
/** Offset 0x02B1 - AcLoadline
PCODE MMIO Mailbox: AcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
0-6249. Intel Recommended Defaults vary by domain and SKU.
**/
UINT16 AcLoadline[5];
/** Offset 0x02BB
**/
UINT8 UnusedUpdSpace8[10];
/** Offset 0x02C5 - DcLoadline
PCODE MMIO Mailbox: DcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
0-6249.Intel Recommended Defaults vary by domain and SKU.
**/
UINT16 DcLoadline[5];
/** Offset 0x02CF - Power State 1 Threshold current
PCODE MMIO Mailbox: Power State 1 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
UINT16 Psi1Threshold[5];
/** Offset 0x02D9 - Power State 2 Threshold current
PCODE MMIO Mailbox: Power State 2 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
UINT16 Psi2Threshold[5];
/** Offset 0x02E3 - Power State 3 Threshold current
PCODE MMIO Mailbox: Power State 3 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
UINT16 Psi3Threshold[5];
/** Offset 0x02ED - Icc Max limit
PCODE MMIO Mailbox: VR Icc Max limit. 0-255A in 1/4 A units. 400 = 100A
**/
UINT16 IccMax[5];
/** Offset 0x02F7 - VR Voltage Limit
PCODE MMIO Mailbox: VR Voltage Limit. Range is 0-7999mV.
**/
UINT16 VrVoltageLimit[5];
/** Offset 0x0301 - Disable Fast Slew Rate for Deep Package C States for VR GT domain
Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
feature enabled. 0: False; 1: True
$EN_DIS
**/
UINT8 FastPkgCRampDisableGt;
/** Offset 0x0302 - Disable Fast Slew Rate for Deep Package C States for VR SA domain
Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
feature enabled. 0: False; 1: True
$EN_DIS
**/
UINT8 FastPkgCRampDisableSa;
/** Offset 0x0303 - Enable VR specific mailbox command
VR specific mailbox commands. 00b - no VR specific command sent. 01b - A
VR mailbox command specifically for the MPS IMPV8 VR will be sent. 10b - VR specific
command sent for PS4 exit issue. 11b - Reserved.
$EN_DIS
**/
UINT8 SendVrMbxCmd;
/** Offset 0x0304 - Reserved
Reserved
**/
UINT8 Reserved2;
/** Offset 0x0305 - Enable or Disable TXT
Enable or Disable TXT; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 TxtEnable;
/** Offset 0x0306
**/
UINT8 UnusedUpdSpace9[6];
/** Offset 0x030C - Deprecated DO NOT USE Skip Multi-Processor Initialization
@deprecated SkipMpInit has been moved to FspmUpd
$EN_DIS
**/
UINT8 SkipMpInit;
/** Offset 0x030D - McIVR RFI Frequency Prefix
PCODE MMIO Mailbox: McIVR RFI Frequency Adjustment Prefix. 0: Plus (+); 1:
Minus (-).
**/
UINT8 McivrRfiFrequencyPrefix;
/** Offset 0x030E - McIVR RFI Frequency Adjustment
PCODE MMIO Mailbox: Adjust the RFI frequency relative to the nominal frequency in
increments of 100KHz. For subtraction, change McivrRfiFrequencyPrefix. 0: Auto.
**/
UINT8 McivrRfiFrequencyAdjust;
/** Offset 0x030F - FIVR RFI Frequency
PCODE MMIO Mailbox: Set the desired RFI frequency, in increments of 100KHz. 0:
Auto. Range varies based on XTAL clock: 0-1918 (Up to 191.8HMz) for 24MHz clock;
0-1535 (Up to 153.5MHz) for 19MHz clock.
**/
UINT16 FivrRfiFrequency;
/** Offset 0x0311 - McIVR RFI Spread Spectrum
PCODE MMIO Mailbox: McIVR RFI Spread Spectrum. 0: 0%; 1: +/- 0.5%; 2: +/-
1%; 3: +/- 1.5%; 4: +/- 2%; 5: +/- 3%; 6: +/- 4%; 7: +/- 5%; 8: +/- 6%.
**/
UINT8 McivrSpreadSpectrum;
/** Offset 0x0312 - FIVR RFI Spread Spectrum
PCODE MMIO Mailbox: FIVR RFI Spread Spectrum, in 0.1% increments. 0: 0%;
Range: 0.0% to 10.0% (0-100).
**/
UINT8 FivrSpreadSpectrum;
/** Offset 0x0313 - Disable Fast Slew Rate for Deep Package C States for VR FIVR domain
Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
feature enabled. 0: False; 1: True
$EN_DIS
**/
UINT8 FastPkgCRampDisableFivr;
/** Offset 0x0314 - Slew Rate configuration for Deep Package C States for VR FIVR domain
Slew Rate configuration for Deep Package C States for VR FIVR domain based on Acoustic
Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16
0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
UINT8 SlowSlewRateForFivr;
/** Offset 0x0315 - CpuBistData
Pointer CPU BIST Data
**/
UINT32 CpuBistData;
/** Offset 0x0319 - Activates VR mailbox command for Intersil VR C-state issues.
Intersil VR mailbox command. 0 - no mailbox command sent. 1 - VR mailbox
command sent for IA/GT rails only. 2 - VR mailbox command sent for IA/GT/SA rails.
**/
UINT8 IslVrCmd;
/** Offset 0x031A - Imon slope1 correction
PCODE MMIO Mailbox: Imon slope correction. Specified in 1/100 increment values.
Range is 0-200. 125 = 1.25. 0: Auto.For all VR Indexes
**/
UINT16 ImonSlope1[5];
/** Offset 0x0324 - CPU VR Power Delivery Design
Used to communicate the power delivery design capability of the board. This value
is an enum of the available power delivery segments that are defined in the Platform
Design Guide.
**/
UINT32 VrPowerDeliveryDesign;
/** Offset 0x0328 - Pre Wake Randomization time
PCODE MMIO Mailbox: Acoustic Migitation Range.Defines the maximum pre-wake randomization
time in micro ticks.This can be programmed only if AcousticNoiseMigitation is enabled.
Range 0-255 0.
**/
UINT8 PreWake;
/** Offset 0x0329 - Ramp Up Randomization time
PCODE MMIO Mailbox: Acoustic Migitation Range.Defines the maximum Ramp Up randomization
time in micro ticks.This can be programmed only if AcousticNoiseMigitation is enabled.Range
0-255 0.
**/
UINT8 RampUp;
/** Offset 0x032A - Ramp Down Randomization time
PCODE MMIO Mailbox: Acoustic Migitation Range.Defines the maximum Ramp Down randomization
time in micro ticks.This can be programmed only if AcousticNoiseMigitation is enabled.Range
0-255 0.
**/
UINT8 RampDown;
/** Offset 0x032B - CpuMpPpi
Pointer for CpuMpPpi
**/
UINT32 CpuMpPpi;
/** Offset 0x032F - CpuMpHob
Pointer for CpuMpHob. This is optional data buffer for CpuMpPpi usage.
**/
UINT32 CpuMpHob;
/** Offset 0x0333 - Enable or Disable processor debug features
Enable or Disable processor debug features; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DebugInterfaceEnable;
/** Offset 0x0334 - ReservedCpuPostMemProduction
Reserved for CPU Post-Mem Production
$EN_DIS
**/
UINT8 ReservedCpuPostMemProduction[18];
/** Offset 0x0346 - Enable DMI ASPM
Deprecated.
$EN_DIS
**/
UINT8 PchDmiAspm;
/** Offset 0x0347 - Enable Power Optimizer
Enable DMI Power Optimizer on PCH side.
$EN_DIS
**/
UINT8 PchPwrOptEnable;
/** Offset 0x0348 - PCH Flash Protection Ranges Write Enble
Write or erase is blocked by hardware.
**/
UINT8 PchWriteProtectionEnable[5];
/** Offset 0x034D - PCH Flash Protection Ranges Read Enble
Read is blocked by hardware.
**/
UINT8 PchReadProtectionEnable[5];
/** Offset 0x0352 - PCH Protect Range Limit
Left shifted address by 12 bits with address bits 11:0 are assumed to be FFFh for
limit comparison.
**/
UINT16 PchProtectedRangeLimit[5];
/** Offset 0x035C - PCH Protect Range Base
Left shifted address by 12 bits with address bits 11:0 are assumed to be 0.
**/
UINT16 PchProtectedRangeBase[5];
/** Offset 0x0366 - Enable Pme
Enable Azalia wake-on-ring.
$EN_DIS
**/
UINT8 PchHdaPme;
/** Offset 0x0367
**/
UINT8 UnusedUpdSpace10;
/** Offset 0x0368 - VC Type
Virtual Channel Type Select: 0: VC0, 1: VC1.
0: VC0, 1: VC1
**/
UINT8 PchHdaVcType;
/** Offset 0x0369 - HD Audio Link Frequency
HDA Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 0: 6MHz, 1: 12MHz, 2: 24MHz.
0: 6MHz, 1: 12MHz, 2: 24MHz
**/
UINT8 PchHdaLinkFrequency;
/** Offset 0x036A - iDisp-Link Frequency
iDisp-Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 4: 96MHz, 3: 48MHz.
4: 96MHz, 3: 48MHz
**/
UINT8 PchHdaIDispLinkFrequency;
/** Offset 0x036B - iDisp-Link T-mode
iDisp-Link T-Mode (PCH_HDAUDIO_IDISP_TMODE enum): 0: 2T, 1: 1T.
0: 2T, 1: 1T
**/
UINT8 PchHdaIDispLinkTmode;
/** Offset 0x036C - Universal Audio Architecture compliance for DSP enabled system
0: Not-UAA Compliant (Intel SST driver supported only), 1: UAA Compliant (HDA Inbox
driver or SST driver supported).
$EN_DIS
**/
UINT8 PchHdaDspUaaCompliance;
/** Offset 0x036D - iDisplay Audio Codec disconnection
0: Not disconnected, enumerable, 1: Disconnected SDI, not enumerable.
$EN_DIS
**/
UINT8 PchHdaIDispCodecDisconnect;
/** Offset 0x036E - USB LFPS Filter selection
For each byte bits 2:0 are for p, bits 4:6 are for n. 0h:1.6ns, 1h:2.4ns, 2h:3.2ns,
3h:4.0ns, 4h:4.8ns, 5h:5.6ns, 6h:6.4ns.
**/
UINT8 PchUsbHsioFilterSel[10];
/** Offset 0x0378
**/
UINT8 UnusedUpdSpace11[5];
/** Offset 0x037D - Enable PCH Io Apic Entry 24-119
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIoApicEntry24_119;
/** Offset 0x037E - PCH Io Apic ID
This member determines IOAPIC ID. Default is 0x02.
**/
UINT8 PchIoApicId;
/** Offset 0x037F
**/
UINT8 UnusedUpdSpace12;
/** Offset 0x0380 - Enable PCH ISH SPI GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshSpiGpioAssign;
/** Offset 0x0381 - Enable PCH ISH UART0 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshUart0GpioAssign;
/** Offset 0x0382 - Enable PCH ISH UART1 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshUart1GpioAssign;
/** Offset 0x0383 - Enable PCH ISH I2C0 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshI2c0GpioAssign;
/** Offset 0x0384 - Enable PCH ISH I2C1 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshI2c1GpioAssign;
/** Offset 0x0385 - Enable PCH ISH I2C2 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshI2c2GpioAssign;
/** Offset 0x0386 - Enable PCH ISH GP_0 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp0GpioAssign;
/** Offset 0x0387 - Enable PCH ISH GP_1 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp1GpioAssign;
/** Offset 0x0388 - Enable PCH ISH GP_2 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp2GpioAssign;
/** Offset 0x0389 - Enable PCH ISH GP_3 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp3GpioAssign;
/** Offset 0x038A - Enable PCH ISH GP_4 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp4GpioAssign;
/** Offset 0x038B - Enable PCH ISH GP_5 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp5GpioAssign;
/** Offset 0x038C - Enable PCH ISH GP_6 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp6GpioAssign;
/** Offset 0x038D - Enable PCH ISH GP_7 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp7GpioAssign;
/** Offset 0x038E - PCH ISH PDT Unlock Msg
0: False; 1: True.
$EN_DIS
**/
UINT8 PchIshPdtUnlock;
/** Offset 0x038F - Enable PCH Lan LTR capabilty of PCH internal LAN
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchLanLtrEnable;
/** Offset 0x0390
**/
UINT8 UnusedUpdSpace13[3];
/** Offset 0x0393 - Enable LOCKDOWN BIOS LOCK
Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region
protection.
$EN_DIS
**/
UINT8 PchLockDownBiosLock;
/** Offset 0x0394 - PCH Compatibility Revision ID
This member describes whether or not the CRID feature of PCH should be enabled.
$EN_DIS
**/
UINT8 PchCrid;
/** Offset 0x0395 - RTC CMOS MEMORY LOCK
Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper
and and lower 128-byte bank of RTC RAM.
$EN_DIS
**/
UINT8 PchLockDownRtcMemoryLock;
/** Offset 0x0396 - Enable PCIE RP HotPlug
Indicate whether the root port is hot plug available.
**/
UINT8 PcieRpHotPlug[24];
/** Offset 0x03AE - Enable PCIE RP Pm Sci
Indicate whether the root port power manager SCI is enabled.
**/
UINT8 PcieRpPmSci[24];
/** Offset 0x03C6 - Enable PCIE RP Ext Sync
Indicate whether the extended synch is enabled.
**/
UINT8 PcieRpExtSync[24];
/** Offset 0x03DE - Enable PCIE RP Transmitter Half Swing
Indicate whether the Transmitter Half Swing is enabled.
**/
UINT8 PcieRpTransmitterHalfSwing[24];
/** Offset 0x03F6 - Enable PCIE RP Clk Req Detect
Probe CLKREQ# signal before enabling CLKREQ# based power management.
**/
UINT8 PcieRpClkReqDetect[24];
/** Offset 0x040E - PCIE RP Advanced Error Report
Indicate whether the Advanced Error Reporting is enabled.
**/
UINT8 PcieRpAdvancedErrorReporting[24];
/** Offset 0x0426 - PCIE RP Unsupported Request Report
Indicate whether the Unsupported Request Report is enabled.
**/
UINT8 PcieRpUnsupportedRequestReport[24];
/** Offset 0x043E - PCIE RP Fatal Error Report
Indicate whether the Fatal Error Report is enabled.
**/
UINT8 PcieRpFatalErrorReport[24];
/** Offset 0x0456 - PCIE RP No Fatal Error Report
Indicate whether the No Fatal Error Report is enabled.
**/
UINT8 PcieRpNoFatalErrorReport[24];
/** Offset 0x046E - PCIE RP Correctable Error Report
Indicate whether the Correctable Error Report is enabled.
**/
UINT8 PcieRpCorrectableErrorReport[24];
/** Offset 0x0486 - PCIE RP System Error On Fatal Error
Indicate whether the System Error on Fatal Error is enabled.
**/
UINT8 PcieRpSystemErrorOnFatalError[24];
/** Offset 0x049E - PCIE RP System Error On Non Fatal Error
Indicate whether the System Error on Non Fatal Error is enabled.
**/
UINT8 PcieRpSystemErrorOnNonFatalError[24];
/** Offset 0x04B6 - PCIE RP System Error On Correctable Error
Indicate whether the System Error on Correctable Error is enabled.
**/
UINT8 PcieRpSystemErrorOnCorrectableError[24];
/** Offset 0x04CE - PCIE RP Max Payload
Max Payload Size supported, Default 128B, see enum PCH_PCIE_MAX_PAYLOAD.
**/
UINT8 PcieRpMaxPayload[24];
/** Offset 0x04E6 - PCH USB3 RX HSIO Tuning parameters
Bits 7:3 are for Signed Magnatude number added to the CTLE code, Bits 2:0 are for
controlling the input offset
**/
UINT8 PchUsbHsioRxTuningParameters[10];
/** Offset 0x04F0 - PCH USB3 HSIO Rx Tuning Enable
Mask for enabling tuning of HSIO Rx signals of USB3 ports. Bits: 0 - HsioCtrlAdaptOffsetCfgEnable,
1 - HsioFilterSelNEnable, 2 - HsioFilterSelPEnable, 3 - HsioOlfpsCfgPullUpDwnResEnable
**/
UINT8 PchUsbHsioRxTuningEnable[10];
/** Offset 0x04FA
**/
UINT8 UnusedUpdSpace14[4];
/** Offset 0x04FE - PCIE RP Pcie Speed
Determines each PCIE Port speed capability. 0: Auto; 1: Gen1; 2: Gen2; 3: Gen3 (see:
PCH_PCIE_SPEED).
**/
UINT8 PcieRpPcieSpeed[24];
/** Offset 0x0516 - PCIE RP Gen3 Equalization Phase Method
PCIe Gen3 Eq Ph3 Method (see PCH_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization;
1: hardware equalization; 4: Fixed Coeficients.
**/
UINT8 PcieRpGen3EqPh3Method[24];
/** Offset 0x052E - PCIE RP Physical Slot Number
Indicates the slot number for the root port. Default is the value as root port index.
**/
UINT8 PcieRpPhysicalSlotNumber[24];
/** Offset 0x0546 - PCIE RP Completion Timeout
The root port completion timeout(see: PCH_PCIE_COMPLETION_TIMEOUT). Default is PchPcieCompletionTO_Default.
**/
UINT8 PcieRpCompletionTimeout[24];
/** Offset 0x055E
**/
UINT8 UnusedUpdSpace15[106];
/** Offset 0x05C8 - PCIE RP Aspm
The ASPM configuration of the root port (see: PCH_PCIE_ASPM_CONTROL). Default is
PchPcieAspmAutoConfig.
**/
UINT8 PcieRpAspm[24];
/** Offset 0x05E0 - PCIE RP L1 Substates
The L1 Substates configuration of the root port (see: PCH_PCIE_L1SUBSTATES_CONTROL).
Default is PchPcieL1SubstatesL1_1_2.
**/
UINT8 PcieRpL1Substates[24];
/** Offset 0x05F8 - PCIE RP Ltr Enable
Latency Tolerance Reporting Mechanism.
**/
UINT8 PcieRpLtrEnable[24];
/** Offset 0x0610 - PCIE RP Ltr Config Lock
0: Disable; 1: Enable.
**/
UINT8 PcieRpLtrConfigLock[24];
/** Offset 0x0628 - PCIE Eq Ph3 Lane Param Cm
PCH_PCIE_EQ_LANE_PARAM. Coefficient C-1.
**/
UINT8 PcieEqPh3LaneParamCm[24];
/** Offset 0x0640 - PCIE Eq Ph3 Lane Param Cp
PCH_PCIE_EQ_LANE_PARAM. Coefficient C+1.
**/
UINT8 PcieEqPh3LaneParamCp[24];
/** Offset 0x0658 - PCIE Sw Eq CoeffList Cm
PCH_PCIE_EQ_PARAM. Coefficient C-1.
**/
UINT8 PcieSwEqCoeffListCm[5];
/** Offset 0x065D - PCIE Sw Eq CoeffList Cp
PCH_PCIE_EQ_PARAM. Coefficient C+1.
**/
UINT8 PcieSwEqCoeffListCp[5];
/** Offset 0x0662 - PCIE Disable RootPort Clock Gating
Describes whether the PCI Express Clock Gating for each root port is enabled by
platform modules. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PcieDisableRootPortClockGating;
/** Offset 0x0663 - PCIE Enable Peer Memory Write
This member describes whether Peer Memory Writes are enabled on the platform.
$EN_DIS
**/
UINT8 PcieEnablePeerMemoryWrite;
/** Offset 0x0664
**/
UINT8 UnusedUpdSpace16;
/** Offset 0x0665 - PCIE Compliance Test Mode
Compliance Test Mode shall be enabled when using Compliance Load Board.
$EN_DIS
**/
UINT8 PcieComplianceTestMode;
/** Offset 0x0666 - PCIE Rp Function Swap
Allows BIOS to use root port function number swapping when root port of function
0 is disabled.
$EN_DIS
**/
UINT8 PcieRpFunctionSwap;
/** Offset 0x0667 - Teton Glacier Support
Enables support for the Teton Glacier card.
$EN_DIS
**/
UINT8 TetonGlacierSupport;
/** Offset 0x0668 - Teton Glacier Cycle Router
Specify to which cycle router Teton Glacier is connected, it is valid only when
Teton Glacier support is enabled. Default is 0 for CNP-H system and 1 for CNP-LP system
**/
UINT8 TetonGlacierCR;
/** Offset 0x0669 - PCH Pm PME_B0_S5_DIS
When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1.
$EN_DIS
**/
UINT8 PchPmPmeB0S5Dis;
/** Offset 0x066A - SPI ChipSelect signal polarity
Selects SPI ChipSelect signal polarity.
**/
UINT8 SerialIoSpiCsPolarity[3];
/** Offset 0x066D - PCIE IMR
Enables Isolated Memory Region for PCIe.
$EN_DIS
**/
UINT8 PcieRpImrEnabled;
/** Offset 0x066E - PCIE IMR port number
Selects PCIE root port number for IMR feature.
**/
UINT8 PcieRpImrSelection;
/** Offset 0x066F
**/
UINT8 UnusedUpdSpace17;
/** Offset 0x0670 - PCH Pm Wol Enable Override
Corresponds to the WOL Enable Override bit in the General PM Configuration B (GEN_PMCON_B) register.
$EN_DIS
**/
UINT8 PchPmWolEnableOverride;
/** Offset 0x0671 - PCH Pm Pcie Wake From DeepSx
Determine if enable PCIe to wake from deep Sx.
$EN_DIS
**/
UINT8 PchPmPcieWakeFromDeepSx;
/** Offset 0x0672 - PCH Pm WoW lan Enable
Determine if WLAN wake from Sx, corresponds to the HOST_WLAN_PP_EN bit in the PWRM_CFG3 register.
$EN_DIS
**/
UINT8 PchPmWoWlanEnable;
/** Offset 0x0673 - PCH Pm WoW lan DeepSx Enable
Determine if WLAN wake from DeepSx, corresponds to the DSX_WLAN_PP_EN bit in the
PWRM_CFG3 register.
$EN_DIS
**/
UINT8 PchPmWoWlanDeepSxEnable;
/** Offset 0x0674 - PCH Pm Lan Wake From DeepSx
Determine if enable LAN to wake from deep Sx.
$EN_DIS
**/
UINT8 PchPmLanWakeFromDeepSx;
/** Offset 0x0675 - PCH Pm Deep Sx Pol
Deep Sx Policy.
$EN_DIS
**/
UINT8 PchPmDeepSxPol;
/** Offset 0x0676 - PCH Pm Slp S3 Min Assert
SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms.
**/
UINT8 PchPmSlpS3MinAssert;
/** Offset 0x0677 - PCH Pm Slp S4 Min Assert
SLP_S4 Minimum Assertion Width Policy. Default is PchSlpS44s.
**/
UINT8 PchPmSlpS4MinAssert;
/** Offset 0x0678 - PCH Pm Slp Sus Min Assert
SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s.
**/
UINT8 PchPmSlpSusMinAssert;
/** Offset 0x0679 - PCH Pm Slp A Min Assert
SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s.
**/
UINT8 PchPmSlpAMinAssert;
/** Offset 0x067A - SLP_S0# Override
Select 'Auto', it will be auto-configured according to probe type. Select 'Enabled'
will disable SLP_S0# assertion whereas 'Disabled' will enable SLP_S0# assertion
when debug is enabled. \n
Note: This BIOS option should keep 'Auto', other options are intended for advanced
configuration only.
0:Disabled, 1:Enabled, 2:Auto
**/
UINT8 SlpS0Override;
/** Offset 0x067B - S0ix Override Settings
Select 'Auto', it will be auto-configured according to probe type. 'No Change' will
keep PMC default settings. Or select the desired debug probe type for S0ix Override
settings.\n
Reminder: DCI OOB (aka BSSB) uses CCA probe.\n
Note: This BIOS option should keep 'Auto', other options are intended for advanced
configuration only.
0:No Change, 1:DCI OOB, 2:USB2 DbC, 3:Auto
**/
UINT8 SlpS0DisQForDebug;
/** Offset 0x067C - USB Overcurrent Override for DbC
This option overrides USB Over Current enablement state that USB OC will be disabled
after enabling this option. Enable when DbC is used to avoid signaling conflicts.
$EN_DIS
**/
UINT8 PchEnableDbcObs;
/** Offset 0x067D
**/
UINT8 UnusedUpdSpace18[3];
/** Offset 0x0680 - PCH Pm Lpc Clock Run
This member describes whether or not the LPC ClockRun feature of PCH should be enabled.
Default value is Disabled
$EN_DIS
**/
UINT8 PchPmLpcClockRun;
/** Offset 0x0681 - PCH Pm Slp Strch Sus Up
Enable SLP_X Stretching After SUS Well Power Up.
$EN_DIS
**/
UINT8 PchPmSlpStrchSusUp;
/** Offset 0x0682 - PCH Pm Slp Lan Low Dc
Enable/Disable SLP_LAN# Low on DC Power.
$EN_DIS
**/
UINT8 PchPmSlpLanLowDc;
/** Offset 0x0683 - PCH Pm Pwr Btn Override Period
PCH power button override period. 000b-4s, 001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s.
**/
UINT8 PchPmPwrBtnOverridePeriod;
/** Offset 0x0684 - PCH Pm Disable Dsx Ac Present Pulldown
When Disable, PCH will internal pull down AC_PRESENT in deep SX and during G3 exit.
$EN_DIS
**/
UINT8 PchPmDisableDsxAcPresentPulldown;
/** Offset 0x0685
**/
UINT8 UnusedUpdSpace19;
/** Offset 0x0686 - PCH Pm Disable Native Power Button
Power button native mode disable.
$EN_DIS
**/
UINT8 PchPmDisableNativePowerButton;
/** Offset 0x0687 - PCH Pm Slp S0 Enable
Indicates whether SLP_S0# is to be asserted when PCH reaches idle state.
$EN_DIS
**/
UINT8 PchPmSlpS0Enable;
/** Offset 0x0688 - PCH Pm ME_WAKE_STS
Clear the ME_WAKE_STS bit in the Power and Reset Status (PRSTS) register.
$EN_DIS
**/
UINT8 PchPmMeWakeSts;
/** Offset 0x0689 - PCH Pm WOL_OVR_WK_STS
Clear the WOL_OVR_WK_STS bit in the Power and Reset Status (PRSTS) register.
$EN_DIS
**/
UINT8 PchPmWolOvrWkSts;
/** Offset 0x068A - PCH Pm Reset Power Cycle Duration
Could be customized in the unit of second. Please refer to EDS for all support settings.
0 is default, 1 is 1 second, 2 is 2 seconds, ...
**/
UINT8 PchPmPwrCycDur;
/** Offset 0x068B - PCH Pm Pcie Pll Ssc
Specifies the Pcie Pll Spread Spectrum Percentage. The default is 0xFF: AUTO - No
BIOS override.
**/
UINT8 PchPmPciePllSsc;
/** Offset 0x068C
**/
UINT8 UnusedUpdSpace20;
/** Offset 0x068D - PCH Sata Pwr Opt Enable
SATA Power Optimizer on PCH side.
$EN_DIS
**/
UINT8 SataPwrOptEnable;
/** Offset 0x068E - PCH Sata eSATA Speed Limit
When enabled, BIOS will configure the PxSCTL.SPD to 2 to limit the eSATA port speed.
$EN_DIS
**/
UINT8 EsataSpeedLimit;
/** Offset 0x068F - PCH Sata Speed Limit
Indicates the maximum speed the SATA controller can support 0h: PchSataSpeedDefault.
**/
UINT8 SataSpeedLimit;
/** Offset 0x0690 - Enable SATA Port HotPlug
Enable SATA Port HotPlug.
**/
UINT8 SataPortsHotPlug[8];
/** Offset 0x0698 - Enable SATA Port Interlock Sw
Enable SATA Port Interlock Sw.
**/
UINT8 SataPortsInterlockSw[8];
/** Offset 0x06A0 - Enable SATA Port External
Enable SATA Port External.
**/
UINT8 SataPortsExternal[8];
/** Offset 0x06A8 - Enable SATA Port SpinUp
Enable the COMRESET initialization Sequence to the device.
**/
UINT8 SataPortsSpinUp[8];
/** Offset 0x06B0 - Enable SATA Port Solid State Drive
0: HDD; 1: SSD.
**/
UINT8 SataPortsSolidStateDrive[8];
/** Offset 0x06B8 - Enable SATA Port Enable Dito Config
Enable DEVSLP Idle Timeout settings (DmVal, DitoVal).
**/
UINT8 SataPortsEnableDitoConfig[8];
/** Offset 0x06C0 - Enable SATA Port DmVal
DITO multiplier. Default is 15.
**/
UINT8 SataPortsDmVal[8];
/** Offset 0x06C8 - Enable SATA Port DmVal
DEVSLP Idle Timeout (DITO), Default is 625.
**/
UINT16 SataPortsDitoVal[8];
/** Offset 0x06D8 - Enable SATA Port ZpOdd
Support zero power ODD.
**/
UINT8 SataPortsZpOdd[8];
/** Offset 0x06E0 - PCH Sata Rst Raid Device Id
Enable RAID Alternate ID.
0:Client, 1:Alternate, 2:Server
**/
UINT8 SataRstRaidDeviceId;
/** Offset 0x06E1 - PCH Sata Rst Raid0
RAID0.
$EN_DIS
**/
UINT8 SataRstRaid0;
/** Offset 0x06E2 - PCH Sata Rst Raid1
RAID1.
$EN_DIS
**/
UINT8 SataRstRaid1;
/** Offset 0x06E3 - PCH Sata Rst Raid10
RAID10.
$EN_DIS
**/
UINT8 SataRstRaid10;
/** Offset 0x06E4 - PCH Sata Rst Raid5
RAID5.
$EN_DIS
**/
UINT8 SataRstRaid5;
/** Offset 0x06E5 - PCH Sata Rst Irrt
Intel Rapid Recovery Technology.
$EN_DIS
**/
UINT8 SataRstIrrt;
/** Offset 0x06E6 - PCH Sata Rst Orom Ui Banner
OROM UI and BANNER.
$EN_DIS
**/
UINT8 SataRstOromUiBanner;
/** Offset 0x06E7 - PCH Sata Rst Orom Ui Delay
00b: 2 secs; 01b: 4 secs; 10b: 6 secs; 11: 8 secs (see: PCH_SATA_OROM_DELAY).
**/
UINT8 SataRstOromUiDelay;
/** Offset 0x06E8 - PCH Sata Rst Hdd Unlock
Indicates that the HDD password unlock in the OS is enabled.
$EN_DIS
**/
UINT8 SataRstHddUnlock;
/** Offset 0x06E9 - PCH Sata Rst Led Locate
Indicates that the LED/SGPIO hardware is attached and ping to locate feature is
enabled on the OS.
$EN_DIS
**/
UINT8 SataRstLedLocate;
/** Offset 0x06EA - PCH Sata Rst Irrt Only
Allow only IRRT drives to span internal and external ports.
$EN_DIS
**/
UINT8 SataRstIrrtOnly;
/** Offset 0x06EB - PCH Sata Rst Smart Storage
RST Smart Storage caching Bit.
$EN_DIS
**/
UINT8 SataRstSmartStorage;
/** Offset 0x06EC - PCH Sata Rst Pcie Storage Remap enable
Enable Intel RST for PCIe Storage remapping.
**/
UINT8 SataRstPcieEnable[3];
/** Offset 0x06EF - PCH Sata Rst Pcie Storage Port
Intel RST for PCIe Storage remapping - PCIe Port Selection (1-based, 0 = autodetect).
**/
UINT8 SataRstPcieStoragePort[3];
/** Offset 0x06F2 - PCH Sata Rst Pcie Device Reset Delay
PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms
**/
UINT8 SataRstPcieDeviceResetDelay[3];
/** Offset 0x06F5 - Enable eMMC HS400 Training
Deprecated.
$EN_DIS
**/
UINT8 PchScsEmmcHs400TuningRequired;
/** Offset 0x06F6 - Set HS400 Tuning Data Valid
Set if HS400 Tuning Data Valid.
$EN_DIS
**/
UINT8 PchScsEmmcHs400DllDataValid;
/** Offset 0x06F7 - Rx Strobe Delay Control
Rx Strobe Delay Control - Rx Strobe Delay DLL 1 (HS400 Mode).
**/
UINT8 PchScsEmmcHs400RxStrobeDll1;
/** Offset 0x06F8 - Tx Data Delay Control
Tx Data Delay Control 1 - Tx Data Delay (HS400 Mode).
**/
UINT8 PchScsEmmcHs400TxDataDll;
/** Offset 0x06F9 - I/O Driver Strength
Deprecated.
0:33 Ohm, 1:40 Ohm, 2:50 Ohm
**/
UINT8 PchScsEmmcHs400DriverStrength;
/** Offset 0x06FA - PCH SerialIo I2C Pads Termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C0,I2C1,I2C2,I2C3,I2C4,I2C5
pads termination respectively. One byte for each controller, byte0 for I2C0, byte1
for I2C1, and so on.
**/
UINT8 PchSerialIoI2cPadsTermination[6];
/** Offset 0x0700
**/
UINT8 UnusedUpdSpace21;
/** Offset 0x0701 - PcdSerialIoUart0PinMuxing
Select SerialIo Uart0 pin muxing. Setting applicable only if SerialIO UART0 is enabled.
0:default pins, 1:pins muxed with CNV_BRI/RGI
**/
UINT8 SerialIoUart0PinMuxing;
/** Offset 0x0702
**/
UINT8 UnusedUpdSpace22[1];
/** Offset 0x0703 - Enables UART hardware flow control, CTS and RTS lines
Enables UART hardware flow control, CTS and RTS linesh.
**/
UINT8 SerialIoUartHwFlowCtrl[3];
/** Offset 0x0706 - UART Number For Debug Purpose
UART number for debug purpose. 0:UART0, 1: UART1, 2:UART2. Note: If UART0 is selected
as CNVi BT Core interface, it cannot be used for debug purpose.
0:UART0, 1:UART1, 2:UART2
**/
UINT8 SerialIoDebugUartNumber;
/** Offset 0x0707 - Enable Debug UART Controller
Enable debug UART controller after post.
$EN_DIS
**/
UINT8 SerialIoEnableDebugUartAfterPost;
/** Offset 0x0708 - Enable Serial IRQ
Determines if enable Serial IRQ.
$EN_DIS
**/
UINT8 PchSirqEnable;
/** Offset 0x0709 - Serial IRQ Mode Select
Serial IRQ Mode Select, 0: quiet mode, 1: continuous mode.
$EN_DIS
**/
UINT8 PchSirqMode;
/** Offset 0x070A - Start Frame Pulse Width
Start Frame Pulse Width, 0: PchSfpw4Clk, 1: PchSfpw6Clk, 2: PchSfpw8Clk.
0: PchSfpw4Clk, 1: PchSfpw6Clk, 2: PchSfpw8Clk
**/
UINT8 PchStartFramePulse;
/** Offset 0x070B - Reserved
Reserved
$EN_DIS
**/
UINT8 ReservedForFuture1;
/** Offset 0x070C - Thermal Device SMI Enable
This locks down SMI Enable on Alert Thermal Sensor Trip.
$EN_DIS
**/
UINT8 PchTsmicLock;
/** Offset 0x070D - Thermal Throttling Custimized T0Level Value
Custimized T0Level value.
**/
UINT16 PchT0Level;
/** Offset 0x070F - Thermal Throttling Custimized T1Level Value
Custimized T1Level value.
**/
UINT16 PchT1Level;
/** Offset 0x0711 - Thermal Throttling Custimized T2Level Value
Custimized T2Level value.
**/
UINT16 PchT2Level;
/** Offset 0x0713 - Enable The Thermal Throttle
Enable the thermal throttle function.
$EN_DIS
**/
UINT8 PchTTEnable;
/** Offset 0x0714 - PMSync State 13
When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force
at least T2 state.
$EN_DIS
**/
UINT8 PchTTState13Enable;
/** Offset 0x0715 - Thermal Throttle Lock
Thermal Throttle Lock.
$EN_DIS
**/
UINT8 PchTTLock;
/** Offset 0x0716 - Thermal Throttling Suggested Setting
Thermal Throttling Suggested Setting.
$EN_DIS
**/
UINT8 TTSuggestedSetting;
/** Offset 0x0717 - Enable PCH Cross Throttling
Enable/Disable PCH Cross Throttling
$EN_DIS
**/
UINT8 TTCrossThrottling;
/** Offset 0x0718 - DMI Thermal Sensor Autonomous Width Enable
DMI Thermal Sensor Autonomous Width Enable.
$EN_DIS
**/
UINT8 PchDmiTsawEn;
/** Offset 0x0719 - DMI Thermal Sensor Suggested Setting
DMT thermal sensor suggested representative values.
$EN_DIS
**/
UINT8 DmiSuggestedSetting;
/** Offset 0x071A - Thermal Sensor 0 Target Width
DMT thermal sensor suggested representative values.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS0TW;
/** Offset 0x071B - Thermal Sensor 1 Target Width
Thermal Sensor 1 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS1TW;
/** Offset 0x071C - Thermal Sensor 2 Target Width
Thermal Sensor 2 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS2TW;
/** Offset 0x071D - Thermal Sensor 3 Target Width
Thermal Sensor 3 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS3TW;
/** Offset 0x071E - Port 0 T1 Multipler
Port 0 T1 Multipler.
**/
UINT8 SataP0T1M;
/** Offset 0x071F - Port 0 T2 Multipler
Port 0 T2 Multipler.
**/
UINT8 SataP0T2M;
/** Offset 0x0720 - Port 0 T3 Multipler
Port 0 T3 Multipler.
**/
UINT8 SataP0T3M;
/** Offset 0x0721 - Port 0 Tdispatch
Port 0 Tdispatch.
**/
UINT8 SataP0TDisp;
/** Offset 0x0722 - Port 1 T1 Multipler
Port 1 T1 Multipler.
**/
UINT8 SataP1T1M;
/** Offset 0x0723 - Port 1 T2 Multipler
Port 1 T2 Multipler.
**/
UINT8 SataP1T2M;
/** Offset 0x0724 - Port 1 T3 Multipler
Port 1 T3 Multipler.
**/
UINT8 SataP1T3M;
/** Offset 0x0725 - Port 1 Tdispatch
Port 1 Tdispatch.
**/
UINT8 SataP1TDisp;
/** Offset 0x0726 - Port 0 Tinactive
Port 0 Tinactive.
**/
UINT8 SataP0Tinact;
/** Offset 0x0727 - Port 0 Alternate Fast Init Tdispatch
Port 0 Alternate Fast Init Tdispatch.
$EN_DIS
**/
UINT8 SataP0TDispFinit;
/** Offset 0x0728 - Port 1 Tinactive
Port 1 Tinactive.
**/
UINT8 SataP1Tinact;
/** Offset 0x0729 - Port 1 Alternate Fast Init Tdispatch
Port 1 Alternate Fast Init Tdispatch.
$EN_DIS
**/
UINT8 SataP1TDispFinit;
/** Offset 0x072A - Sata Thermal Throttling Suggested Setting
Sata Thermal Throttling Suggested Setting.
$EN_DIS
**/
UINT8 SataThermalSuggestedSetting;
/** Offset 0x072B - Enable Memory Thermal Throttling
Enable Memory Thermal Throttling.
$EN_DIS
**/
UINT8 PchMemoryThrottlingEnable;
/** Offset 0x072C - Memory Thermal Throttling
Enable Memory Thermal Throttling.
**/
UINT8 PchMemoryPmsyncEnable[2];
/** Offset 0x072E - Enable Memory Thermal Throttling
Enable Memory Thermal Throttling.
**/
UINT8 PchMemoryC0TransmitEnable[2];
/** Offset 0x0730 - Enable Memory Thermal Throttling
Enable Memory Thermal Throttling.
**/
UINT8 PchMemoryPinSelection[2];
/** Offset 0x0732 - Thermal Device Temperature
Decides the temperature.
**/
UINT16 PchTemperatureHotLevel;
/** Offset 0x0734 - Enable xHCI Compliance Mode
Compliance Mode can be enabled for testing through this option but this is disabled
by default.
$EN_DIS
**/
UINT8 PchEnableComplianceMode;
/** Offset 0x0735 - USB2 Port Over Current Pin
Describe the specific over current pin number of USB 2.0 Port N.
**/
UINT8 Usb2OverCurrentPin[16];
/** Offset 0x0745 - USB3 Port Over Current Pin
Describe the specific over current pin number of USB 3.0 Port N.
**/
UINT8 Usb3OverCurrentPin[10];
/** Offset 0x074F - Enable 8254 Static Clock Gating
Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time
might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support
boot legacy OS using 8254 timer. Also enable this while S0ix is enabled.
$EN_DIS
**/
UINT8 Enable8254ClockGating;
/** Offset 0x0750 - PCH Sata Rst Optane Memory
Optane Memory
$EN_DIS
**/
UINT8 SataRstOptaneMemory;
/** Offset 0x0751 - PCH Sata Rst CPU Attached Storage
CPU Attached Storage
$EN_DIS
**/
UINT8 SataRstCpuAttachedStorage;
/** Offset 0x0752 - Enable 8254 Static Clock Gating On S3
This is only applicable when Enable8254ClockGating is disabled. FSP will do the
8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This
avoids the SMI requirement for the programming.
$EN_DIS
**/
UINT8 Enable8254ClockGatingOnS3;
/** Offset 0x0753
**/
UINT8 UnusedUpdSpace23;
/** Offset 0x0754 - Pch PCIE device override table pointer
The PCIe device table is being used to override PCIe device ASPM settings. This
is a pointer points to a 32bit address. And it's only used in PostMem phase. Please
refer to PCH_PCIE_DEVICE_OVERRIDE structure for the table. Last entry VendorId
must be 0.
**/
UINT32 PchPcieDeviceOverrideTablePtr;
/** Offset 0x0758 - Enable TCO timer.
When FALSE, it disables PCH ACPI timer, and stops TCO timer. NOTE: This will have
huge power impact when it's enabled. If TCO timer is disabled, uCode ACPI timer
emulation must be enabled, and WDAT table must not be exposed to the OS.
$EN_DIS
**/
UINT8 EnableTcoTimer;
/** Offset 0x0759 - BgpdtHash[4]
BgpdtHash values
**/
UINT64 BgpdtHash[4];
/** Offset 0x0779 - BiosGuardAttr
BiosGuardAttr default values
**/
UINT32 BiosGuardAttr;
/** Offset 0x077D - BiosGuardModulePtr
BiosGuardModulePtr default values
**/
UINT64 BiosGuardModulePtr;
/** Offset 0x0785 - SendEcCmd
SendEcCmd function pointer. \n
@code typedef EFI_STATUS (EFIAPI *PLATFORM_SEND_EC_COMMAND) (IN EC_COMMAND_TYPE
EcCmdType, IN UINT8 EcCmd, IN UINT8 SendData, IN OUT UINT8 *ReceiveData); @endcode
**/
UINT64 SendEcCmd;
/** Offset 0x078D - EcCmdProvisionEav
Ephemeral Authorization Value default values. Provisions an ephemeral shared secret to the EC
**/
UINT8 EcCmdProvisionEav;
/** Offset 0x078E - EcCmdLock
EcCmdLock default values. Locks Ephemeral Authorization Value sent previously
**/
UINT8 EcCmdLock;
/** Offset 0x078F - SgxEpoch0
SgxEpoch0 default values
**/
UINT64 SgxEpoch0;
/** Offset 0x0797 - SgxEpoch1
SgxEpoch1 default values
**/
UINT64 SgxEpoch1;
/** Offset 0x079F - SgxSinitNvsData
SgxSinitNvsData default values
**/
UINT8 SgxSinitNvsData;
/** Offset 0x07A0 - Si Config CSM Flag.
Platform specific common policies that used by several silicon components. CSM status flag.
$EN_DIS
**/
UINT8 SiCsmFlag;
/** Offset 0x07A1
**/
UINT32 SiSsidTablePtr;
/** Offset 0x07A5
**/
UINT16 SiNumberOfSsidTableEntry;
/** Offset 0x07A7 - SATA RST Interrupt Mode
Allowes to choose which interrupts will be implemented by SATA controller in RAID mode.
0:Msix, 1:Msi, 2:Legacy
**/
UINT8 SataRstInterrupt;
/** Offset 0x07A8 - ME Unconfig on RTC clear
0: Disable ME Unconfig On Rtc Clear. 1: Enable ME Unconfig On Rtc Clear.
2: Cmos is clear, status unkonwn. 3: Reserved
0: Disable ME Unconfig On Rtc Clear, 1: Enable ME Unconfig On Rtc Clear, 2: Cmos
is clear, 3: Reserved
**/
UINT8 MeUnconfigOnRtcClear;
/** Offset 0x07A9 - Enable PS_ON.
PS_ON is a new C10 state from the CPU on desktop SKUs that enables a lower power
target that will be required by the California Energy Commission (CEC). When FALSE,
PS_ON is to be disabled.
$EN_DIS
**/
UINT8 PsOnEnable;
/** Offset 0x07AA - Pmc Cpu C10 Gate Pin Enable
Enable/Disable platform support for CPU_C10_GATE# pin to control gating of CPU VccIO
and VccSTG rails instead of SLP_S0# pin.
$EN_DIS
**/
UINT8 PmcCpuC10GatePinEnable;
/** Offset 0x07AB - Pch Dmi Aspm Ctrl
ASPM configuration on the PCH side of the DMI/OPI Link. Default is PchPcieAspmAutoConfig
0:Disabled, 1:L0s, 2:L1, 3:L0sL1, 4:Auto
**/
UINT8 PchDmiAspmCtrl;
/** Offset 0x07AC
**/
UINT8 ReservedFspsUpd[1];
} FSP_S_CONFIG;
/** Fsp S Test Configuration
**/
typedef struct {
/** Offset 0x07AD
**/
UINT32 Signature;
/** Offset 0x07B1 - Enable/Disable Device 7
Enable: Device 7 enabled, Disable (Default): Device 7 disabled
$EN_DIS
**/
UINT8 ChapDeviceEnable;
/** Offset 0x07B2 - Skip PAM register lock
Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
PAM registers will be locked by RC
$EN_DIS
**/
UINT8 SkipPamLock;
/** Offset 0x07B3 - EDRAM Test Mode
Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
PAM registers will be locked by RC
0: EDRAM SW disable, 1: EDRAM SW Enable, 2: EDRAM HW mode
**/
UINT8 EdramTestMode;
/** Offset 0x07B4 - DMI Extended Sync Control
Enable: Enable DMI Extended Sync Control, Disable(Default): Disable DMI Extended
Sync Control
$EN_DIS
**/
UINT8 DmiExtSync;
/** Offset 0x07B5 - DMI IOT Control
Enable: Enable DMI IOT Control, Disable(Default): Disable DMI IOT Control
$EN_DIS
**/
UINT8 DmiIot;
/** Offset 0x07B6 - PEG Max Payload size per root port
0xFF(Default):Auto, 0x1: Force 128B, 0x2: Force 256B
0xFF: Auto, 0x1: Force 128B, 0x2: Force 256B
**/
UINT8 PegMaxPayload[4];
/** Offset 0x07BA - Enable/Disable IGFX RenderStandby
Enable(Default): Enable IGFX RenderStandby, Disable: Disable IGFX RenderStandby
$EN_DIS
**/
UINT8 RenderStandby;
/** Offset 0x07BB - Enable/Disable IGFX PmSupport
Enable(Default): Enable IGFX PmSupport, Disable: Disable IGFX PmSupport
$EN_DIS
**/
UINT8 PmSupport;
/** Offset 0x07BC - Enable/Disable CdynmaxClamp
Enable(Default): Enable CdynmaxClamp, Disable: Disable CdynmaxClamp
$EN_DIS
**/
UINT8 CdynmaxClampEnable;
/** Offset 0x07BD - Disable VT-d
0=Enable/FALSE(VT-d enabled), 1=Disable/TRUE (VT-d disabled)
$EN_DIS
**/
UINT8 VtdDisable;
/** Offset 0x07BE - GT Frequency Limit
0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
0x18: 1200 Mhz
0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
0x18: 1200 Mhz
**/
UINT8 GtFreqMax;
/** Offset 0x07BF - Disable Turbo GT
0=Disable: GT frequency is not limited, 1=Enable: Disables Turbo GT frequency
$EN_DIS
**/
UINT8 DisableTurboGt;
/** Offset 0x07C0 - SaPostMemTestRsvd
Reserved for SA Post-Mem Test
$EN_DIS
**/
UINT8 SaPostMemTestRsvd[11];
/** Offset 0x07CB - 1-Core Ratio Limit
1-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 1-Core
Ratio Limit Must be greater than or equal to 2-Core Ratio Limit, 3-Core Ratio Limit,
4-Core Ratio Limit, 5-Core Ratio Limit, 6-Core Ratio Limit, 7-Core Ratio Limit,
8-Core Ratio Limit. Range is 0 to 255
**/
UINT8 OneCoreRatioLimit;
/** Offset 0x07CC - 2-Core Ratio Limit
2-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 2-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
**/
UINT8 TwoCoreRatioLimit;
/** Offset 0x07CD - 3-Core Ratio Limit
3-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 3-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
**/
UINT8 ThreeCoreRatioLimit;
/** Offset 0x07CE - 4-Core Ratio Limit
4-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 4-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
**/
UINT8 FourCoreRatioLimit;
/** Offset 0x07CF - Enable or Disable HWP
Enable or Disable HWP(Hardware P states) Support. 0: Disable; 1: Enable;
2-3:Reserved
$EN_DIS
**/
UINT8 Hwp;
/** Offset 0x07D0 - Hardware Duty Cycle Control
Hardware Duty Cycle Control configuration. 0: Disabled; 1: Enabled 2-3:Reserved
$EN_DIS
**/
UINT8 HdcControl;
/** Offset 0x07D1 - Package Long duration turbo mode time
Package Long duration turbo mode time window in seconds. 0 = AUTO, uses 28 seconds.
Valid values(Unit in seconds) 1 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40
, 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
UINT8 PowerLimit1Time;
/** Offset 0x07D2 - Short Duration Turbo Mode
Enable or Disable short duration Turbo Mode. 0 : Disable; 1: Enable
$EN_DIS
**/
UINT8 PowerLimit2;
/** Offset 0x07D3 - Turbo settings Lock
Lock all Turbo settings Enable/Disable; 0: Disable , 1: Enable
$EN_DIS
**/
UINT8 TurboPowerLimitLock;
/** Offset 0x07D4 - Package PL3 time window
Package PL3 time window range for this policy from 0 to 64ms
**/
UINT8 PowerLimit3Time;
/** Offset 0x07D5 - Package PL3 Duty Cycle
Package PL3 Duty Cycle; Valid Range is 0 to 100
**/
UINT8 PowerLimit3DutyCycle;
/** Offset 0x07D6 - Package PL3 Lock
Package PL3 Lock Enable/Disable; 0: Disable ; 1: Enable
$EN_DIS
**/
UINT8 PowerLimit3Lock;
/** Offset 0x07D7 - Package PL4 Lock
Package PL4 Lock Enable/Disable; 0: Disable ; 1: Enable
$EN_DIS
**/
UINT8 PowerLimit4Lock;
/** Offset 0x07D8 - TCC Activation Offset
TCC Activation Offset. Offset from factory set TCC activation temperature at which
the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation
Temperature, in volts.For Y SKU, the recommended default for this policy is 15,
For all other SKUs the recommended default are 0
**/
UINT8 TccActivationOffset;
/** Offset 0x07D9 - Tcc Offset Clamp Enable/Disable
Tcc Offset Clamp for Runtime Average Temperature Limit (RATL) allows CPU to throttle
below P1.For Y SKU, the recommended default for this policy is 1: Enabled,
For all other SKUs the recommended default are 0: Disabled.
$EN_DIS
**/
UINT8 TccOffsetClamp;
/** Offset 0x07DA - Tcc Offset Lock
Tcc Offset Lock for Runtime Average Temperature Limit (RATL) to lock temperature
target; 0: Disabled; 1: Enabled.
$EN_DIS
**/
UINT8 TccOffsetLock;
/** Offset 0x07DB - Custom Ratio State Entries
The number of custom ratio state entries, ranges from 0 to 40 for a valid custom
ratio table.Sets the number of custom P-states. At least 2 states must be present
**/
UINT8 NumberOfEntries;
/** Offset 0x07DC - Custom Short term Power Limit time window
Short term Power Limit time window value for custom CTDP level 1. Valid Range 0
to 128, 0 = AUTO
**/
UINT8 Custom1PowerLimit1Time;
/** Offset 0x07DD - Custom Turbo Activation Ratio
Turbo Activation Ratio for custom cTDP level 1. Valid Range 0 to 255
**/
UINT8 Custom1TurboActivationRatio;
/** Offset 0x07DE - Custom Config Tdp Control
Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
UINT8 Custom1ConfigTdpControl;
/** Offset 0x07DF - Custom Short term Power Limit time window
Short term Power Limit time window value for custom CTDP level 2. Valid Range 0
to 128, 0 = AUTO
**/
UINT8 Custom2PowerLimit1Time;
/** Offset 0x07E0 - Custom Turbo Activation Ratio
Turbo Activation Ratio for custom cTDP level 2. Valid Range 0 to 255
**/
UINT8 Custom2TurboActivationRatio;
/** Offset 0x07E1 - Custom Config Tdp Control
Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
UINT8 Custom2ConfigTdpControl;
/** Offset 0x07E2 - Custom Short term Power Limit time window
Short term Power Limit time window value for custom CTDP level 3. Valid Range 0
to 128, 0 = AUTO
**/
UINT8 Custom3PowerLimit1Time;
/** Offset 0x07E3 - Custom Turbo Activation Ratio
Turbo Activation Ratio for custom cTDP level 3. Valid Range 0 to 255
**/
UINT8 Custom3TurboActivationRatio;
/** Offset 0x07E4 - Custom Config Tdp Control
Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
UINT8 Custom3ConfigTdpControl;
/** Offset 0x07E5 - ConfigTdp mode settings Lock
Lock the ConfigTdp mode settings from runtime changes; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ConfigTdpLock;
/** Offset 0x07E6 - Load Configurable TDP SSDT
Configure whether to load Configurable TDP SSDT; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 ConfigTdpBios;
/** Offset 0x07E7 - PL1 Enable value
PL1 Enable value to limit average platform power. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PsysPowerLimit1;
/** Offset 0x07E8 - PL1 timewindow
PL1 timewindow in seconds. 0 = AUTO, uses 28 seconds. Valid values(Unit in seconds)
1 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
UINT8 PsysPowerLimit1Time;
/** Offset 0x07E9 - PL2 Enable Value
PL2 Enable activates the PL2 value to limit average platform power.0: Disable;
1: Enable.
$EN_DIS
**/
UINT8 PsysPowerLimit2;
/** Offset 0x07EA - Enable or Disable MLC Streamer Prefetcher
Enable or Disable MLC Streamer Prefetcher; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MlcStreamerPrefetcher;
/** Offset 0x07EB - Enable or Disable MLC Spatial Prefetcher
Enable or Disable MLC Spatial Prefetcher; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 MlcSpatialPrefetcher;
/** Offset 0x07EC - Enable or Disable Monitor /MWAIT instructions
Enable or Disable Monitor /MWAIT instructions; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MonitorMwaitEnable;
/** Offset 0x07ED - Enable or Disable initialization of machine check registers
Enable or Disable initialization of machine check registers; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MachineCheckEnable;
/** Offset 0x07EE - Deprecated DO NOT USE Enable or Disable processor debug features
@deprecated Enable or Disable processor debug features; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DebugInterfaceEnable;
/** Offset 0x07EF - Lock or Unlock debug interface features
Lock or Unlock debug interface features; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DebugInterfaceLockEnable;
/** Offset 0x07F0 - AP Idle Manner of waiting for SIPI
AP Idle Manner of waiting for SIPI; 1: HALT loop; 2: MWAIT loop; 3: RUN loop.
1: HALT loop, 2: MWAIT loop, 3: RUN loop
**/
UINT8 ApIdleManner;
/** Offset 0x07F1 - Control on Processor Trace output scheme
Control on Processor Trace output scheme; 0: Single Range Output; 1: ToPA Output.
0: Single Range Output, 1: ToPA Output
**/
UINT8 ProcessorTraceOutputScheme;
/** Offset 0x07F2 - Enable or Disable Processor Trace feature
Enable or Disable Processor Trace feature; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 ProcessorTraceEnable;
/** Offset 0x07F3 - Base of memory region allocated for Processor Trace
Base address of memory region allocated for Processor Trace. Processor Trace requires
2^N alignment and size in bytes per thread, from 4KB to 128MB. 0: Disable
**/
UINT64 ProcessorTraceMemBase;
/** Offset 0x07FB - Memory region allocation for Processor Trace
Length in bytes of memory region allocated for Processor Trace. Processor Trace
requires 2^N alignment and size in bytes per thread, from 4KB to 128MB. 0: Disable
**/
UINT32 ProcessorTraceMemLength;
/** Offset 0x07FF - Enable or Disable Voltage Optimization feature
Enable or Disable Voltage Optimization feature 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 VoltageOptimization;
/** Offset 0x0800 - Enable or Disable Intel SpeedStep Technology
Enable or Disable Intel SpeedStep Technology. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 Eist;
/** Offset 0x0801 - Enable or Disable Energy Efficient P-state
Enable or Disable Energy Efficient P-state will be applied in Turbo mode. Disable;
1: Enable
$EN_DIS
**/
UINT8 EnergyEfficientPState;
/** Offset 0x0802 - Enable or Disable Energy Efficient Turbo
Enable or Disable Energy Efficient Turbo, will be applied in Turbo mode. Disable;
1: Enable
$EN_DIS
**/
UINT8 EnergyEfficientTurbo;
/** Offset 0x0803 - Enable or Disable T states
Enable or Disable T states; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 TStates;
/** Offset 0x0804 - Enable or Disable Bi-Directional PROCHOT#
Enable or Disable Bi-Directional PROCHOT#; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 BiProcHot;
/** Offset 0x0805 - Enable or Disable PROCHOT# signal being driven externally
Enable or Disable PROCHOT# signal being driven externally; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DisableProcHotOut;
/** Offset 0x0806 - Enable or Disable PROCHOT# Response
Enable or Disable PROCHOT# Response; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 ProcHotResponse;
/** Offset 0x0807 - Enable or Disable VR Thermal Alert
Enable or Disable VR Thermal Alert; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DisableVrThermalAlert;
/** Offset 0x0808 - Enable or Disable Thermal Reporting
Enable or Disable Thermal Reporting through ACPI tables; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 AutoThermalReporting;
/** Offset 0x0809 - Enable or Disable Thermal Monitor
Enable or Disable Thermal Monitor; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ThermalMonitor;
/** Offset 0x080A - Enable or Disable CPU power states (C-states)
Enable or Disable CPU power states (C-states). 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 Cx;
/** Offset 0x080B - Configure C-State Configuration Lock
Configure C-State Configuration Lock; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PmgCstCfgCtrlLock;
/** Offset 0x080C - Enable or Disable Enhanced C-states
Enable or Disable Enhanced C-states. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 C1e;
/** Offset 0x080D - Enable or Disable Package Cstate Demotion
Enable or Disable Package Cstate Demotion. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 PkgCStateDemotion;
/** Offset 0x080E - Enable or Disable Package Cstate UnDemotion
Enable or Disable Package Cstate UnDemotion. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 PkgCStateUnDemotion;
/** Offset 0x080F - Enable or Disable CState-Pre wake
Enable or Disable CState-Pre wake. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 CStatePreWake;
/** Offset 0x0810 - Enable or Disable TimedMwait Support.
Enable or Disable TimedMwait Support. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 TimedMwait;
/** Offset 0x0811 - Enable or Disable IO to MWAIT redirection
Enable or Disable IO to MWAIT redirection; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 CstCfgCtrIoMwaitRedirection;
/** Offset 0x0812 - Set the Max Pkg Cstate
Set the Max Pkg Cstate. Default set to Auto which limits the Max Pkg Cstate to deep
C-state. Valid values 0 - C0/C1 , 1 - C2 , 2 - C3 , 3 - C6 , 4 - C7 , 5 - C7S ,
6 - C8 , 7 - C9 , 8 - C10 , 254 - CPU Default , 255 - Auto
**/
UINT8 PkgCStateLimit;
/** Offset 0x0813 - TimeUnit for C-State Latency Control0
TimeUnit for C-State Latency Control0; Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl0TimeUnit;
/** Offset 0x0814 - TimeUnit for C-State Latency Control1
TimeUnit for C-State Latency Control1;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl1TimeUnit;
/** Offset 0x0815 - TimeUnit for C-State Latency Control2
TimeUnit for C-State Latency Control2;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl2TimeUnit;
/** Offset 0x0816 - TimeUnit for C-State Latency Control3
TimeUnit for C-State Latency Control3;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl3TimeUnit;
/** Offset 0x0817 - TimeUnit for C-State Latency Control4
Time - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl4TimeUnit;
/** Offset 0x0818 - TimeUnit for C-State Latency Control5
TimeUnit for C-State Latency Control5;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl5TimeUnit;
/** Offset 0x0819 - Interrupt Redirection Mode Select
Interrupt Redirection Mode Select.0: Fixed priority; 1: Round robin;2: Hash vector;4:
PAIR with fixed priority;5: PAIR with round robin;6: PAIR with hash vector;7: No change.
**/
UINT8 PpmIrmSetting;
/** Offset 0x081A - Lock prochot configuration
Lock prochot configuration Enable/Disable; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ProcHotLock;
/** Offset 0x081B - Configuration for boot TDP selection
Configuration for boot TDP selection; 0: TDP Nominal; 1: TDP Down; 2: TDP
Up;0xFF : Deactivate
**/
UINT8 ConfigTdpLevel;
/** Offset 0x081C - Race To Halt
Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency
in order to enter pkg C-State faster to reduce overall power. (RTH is controlled
through MSR 1FC bit 20)Disable; 1: Enable
$EN_DIS
**/
UINT8 RaceToHalt;
/** Offset 0x081D - Max P-State Ratio
Max P-State Ratio, Valid Range 0 to 0x7F
**/
UINT8 MaxRatio;
/** Offset 0x081E - P-state ratios for custom P-state table
P-state ratios for custom P-state table. NumberOfEntries has valid range between
0 to 40. For no. of P-States supported(NumberOfEntries) , StateRatio[NumberOfEntries]
are configurable. Valid Range of each entry is 0 to 0x7F
**/
UINT8 StateRatio[40];
/** Offset 0x0846 - P-state ratios for max 16 version of custom P-state table
P-state ratios for max 16 version of custom P-state table. This table is used for
OS versions limited to a max of 16 P-States. If the first entry of this table is
0, or if Number of Entries is 16 or less, then this table will be ignored, and
up to the top 16 values of the StateRatio table will be used instead. Valid Range
of each entry is 0 to 0x7F
**/
UINT8 StateRatioMax16[16];
/** Offset 0x0856 - Platform Power Pmax
PCODE MMIO Mailbox: Platform Power Pmax. 0 - Auto Specified in 1/8 Watt increments.
Range 0-1024 Watts. Value of 800 = 100W
**/
UINT16 PsysPmax;
/** Offset 0x0858 - Interrupt Response Time Limit of C-State LatencyContol0
Interrupt Response Time Limit of C-State LatencyContol0.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl0Irtl;
/** Offset 0x085A - Interrupt Response Time Limit of C-State LatencyContol1
Interrupt Response Time Limit of C-State LatencyContol1.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl1Irtl;
/** Offset 0x085C - Interrupt Response Time Limit of C-State LatencyContol2
Interrupt Response Time Limit of C-State LatencyContol2.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl2Irtl;
/** Offset 0x085E - Interrupt Response Time Limit of C-State LatencyContol3
Interrupt Response Time Limit of C-State LatencyContol3.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl3Irtl;
/** Offset 0x0860 - Interrupt Response Time Limit of C-State LatencyContol4
Interrupt Response Time Limit of C-State LatencyContol4.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl4Irtl;
/** Offset 0x0862 - Interrupt Response Time Limit of C-State LatencyContol5
Interrupt Response Time Limit of C-State LatencyContol5.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl5Irtl;
/** Offset 0x0864 - Package Long duration turbo mode power limit
Package Long duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit1;
/** Offset 0x0868 - Package Short duration turbo mode power limit
Package Short duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit2Power;
/** Offset 0x086C - Package PL3 power limit
Package PL3 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit3;
/** Offset 0x0870 - Package PL4 power limit
Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 1023875 in Step size of 125
**/
UINT32 PowerLimit4;
/** Offset 0x0874 - Tcc Offset Time Window for RATL
Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 1023875 in Step size of 125
**/
UINT32 TccOffsetTimeWindowForRatl;
/** Offset 0x0878 - Short term Power Limit value for custom cTDP level 1
Short term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom1PowerLimit1;
/** Offset 0x087C - Long term Power Limit value for custom cTDP level 1
Long term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom1PowerLimit2;
/** Offset 0x0880 - Short term Power Limit value for custom cTDP level 2
Short term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom2PowerLimit1;
/** Offset 0x0884 - Long term Power Limit value for custom cTDP level 2
Long term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom2PowerLimit2;
/** Offset 0x0888 - Short term Power Limit value for custom cTDP level 3
Short term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom3PowerLimit1;
/** Offset 0x088C - Long term Power Limit value for custom cTDP level 3
Long term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom3PowerLimit2;
/** Offset 0x0890 - Platform PL1 power
Platform PL1 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
0 to 4095875 in Step size of 125
**/
UINT32 PsysPowerLimit1Power;
/** Offset 0x0894 - Platform PL2 power
Platform PL2 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
0 to 4095875 in Step size of 125
**/
UINT32 PsysPowerLimit2Power;
/** Offset 0x0898 - Set Three Strike Counter Disable
False (default): Three Strike counter will be incremented and True: Prevents Three
Strike counter from incrementing; 0: False; 1: True.
0: False, 1: True
**/
UINT8 ThreeStrikeCounterDisable;
/** Offset 0x0899 - Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT
Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 HwpInterruptControl;
/** Offset 0x089A - 5-Core Ratio Limit
5-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 5-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
0x0:0xFF
**/
UINT8 FiveCoreRatioLimit;
/** Offset 0x089B - 6-Core Ratio Limit
6-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 6-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
0x0:0xFF
**/
UINT8 SixCoreRatioLimit;
/** Offset 0x089C - 7-Core Ratio Limit
7-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 7-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
0x0:0xFF
**/
UINT8 SevenCoreRatioLimit;
/** Offset 0x089D - 8-Core Ratio Limit
8-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 8-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
0x0:0xFF
**/
UINT8 EightCoreRatioLimit;
/** Offset 0x089E - Intel Turbo Boost Max Technology 3.0
Intel Turbo Boost Max Technology 3.0. 0: Disabled; 1: Enabled
$EN_DIS
**/
UINT8 EnableItbm;
/** Offset 0x089F - Intel Turbo Boost Max Technology 3.0 Driver
Intel Turbo Boost Max Technology 3.0 Driver 0: Disabled; 1: Enabled
$EN_DIS
**/
UINT8 EnableItbmDriver;
/** Offset 0x08A0 - Enable or Disable C1 Cstate Demotion
Enable or Disable C1 Cstate Demotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C1StateAutoDemotion;
/** Offset 0x08A1 - Enable or Disable C1 Cstate UnDemotion
Enable or Disable C1 Cstate UnDemotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C1StateUnDemotion;
/** Offset 0x08A2 - CpuWakeUpTimer
Enable long CPU Wakeup Timer. When enabled, the cpu internal wakeup time is increased
to 180 seconds. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 CpuWakeUpTimer;
/** Offset 0x08A3 - Minimum Ring ratio limit override
Minimum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo
ratio limit
**/
UINT8 MinRingRatioLimit;
/** Offset 0x08A4 - Minimum Ring ratio limit override
Maximum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo
ratio limit
**/
UINT8 MaxRingRatioLimit;
/** Offset 0x08A5 - Enable or Disable C3 Cstate Demotion
Enable or Disable C3 Cstate Demotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C3StateAutoDemotion;
/** Offset 0x08A6 - Enable or Disable C3 Cstate UnDemotion
Enable or Disable C3 Cstate UnDemotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C3StateUnDemotion;
/** Offset 0x08A7 - ReservedCpuPostMemTest
Reserved for CPU Post-Mem Test
$EN_DIS
**/
UINT8 ReservedCpuPostMemTest[19];
/** Offset 0x08BA - SgxSinitDataFromTpm
SgxSinitDataFromTpm default values
**/
UINT8 SgxSinitDataFromTpm;
/** Offset 0x08BB - End of Post message
Test, Send End of Post message. Disable(0x0): Disable EOP message, Send in PEI(0x1):
EOP send in PEI, Send in DXE(0x2)(Default): EOP send in PEI
0:Disable, 1:Send in PEI, 2:Send in DXE, 3:Reserved
**/
UINT8 EndOfPostMessage;
/** Offset 0x08BC - D0I3 Setting for HECI Disable
Test, 0: disable, 1: enable, Setting this option disables setting D0I3 bit for all
HECI devices
$EN_DIS
**/
UINT8 DisableD0I3SettingForHeci;
/** Offset 0x08BD - HD Audio Reset Wait Timer
The delay timer after Azalia reset, the value is number of microseconds. Default is 600.
**/
UINT16 PchHdaResetWaitTimer;
/** Offset 0x08BF - Enable LOCKDOWN SMI
Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit.
$EN_DIS
**/
UINT8 PchLockDownGlobalSmi;
/** Offset 0x08C0 - Enable LOCKDOWN BIOS Interface
Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register.
$EN_DIS
**/
UINT8 PchLockDownBiosInterface;
/** Offset 0x08C1 - Unlock all GPIO pads
Force all GPIO pads to be unlocked for debug purpose.
$EN_DIS
**/
UINT8 PchUnlockGpioPads;
/** Offset 0x08C2 - PCH Unlock SBI access
Deprecated
$EN_DIS
**/
UINT8 PchSbiUnlock;
/** Offset 0x08C3 - PCH Unlock SideBand access
The SideBand PortID mask for certain end point (e.g. PSFx) will be locked before
3rd party code execution. 0: Lock SideBand access; 1: Unlock SideBand access.
$EN_DIS
**/
UINT8 PchSbAccessUnlock;
/** Offset 0x08C4 - PCIE RP Ltr Max Snoop Latency
Latency Tolerance Reporting, Max Snoop Latency.
**/
UINT16 PcieRpLtrMaxSnoopLatency[24];
/** Offset 0x08F4 - PCIE RP Ltr Max No Snoop Latency
Latency Tolerance Reporting, Max Non-Snoop Latency.
**/
UINT16 PcieRpLtrMaxNoSnoopLatency[24];
/** Offset 0x0924 - PCIE RP Snoop Latency Override Mode
Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
UINT8 PcieRpSnoopLatencyOverrideMode[24];
/** Offset 0x093C - PCIE RP Snoop Latency Override Multiplier
Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
UINT8 PcieRpSnoopLatencyOverrideMultiplier[24];
/** Offset 0x0954 - PCIE RP Snoop Latency Override Value
Latency Tolerance Reporting, Snoop Latency Override Value.
**/
UINT16 PcieRpSnoopLatencyOverrideValue[24];
/** Offset 0x0984 - PCIE RP Non Snoop Latency Override Mode
Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
UINT8 PcieRpNonSnoopLatencyOverrideMode[24];
/** Offset 0x099C - PCIE RP Non Snoop Latency Override Multiplier
Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
UINT8 PcieRpNonSnoopLatencyOverrideMultiplier[24];
/** Offset 0x09B4 - PCIE RP Non Snoop Latency Override Value
Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
UINT16 PcieRpNonSnoopLatencyOverrideValue[24];
/** Offset 0x09E4 - PCIE RP Slot Power Limit Scale
Specifies scale used for slot power limit value. Leave as 0 to set to default.
**/
UINT8 PcieRpSlotPowerLimitScale[24];
/** Offset 0x09FC - PCIE RP Slot Power Limit Value
Specifies upper limit on power supplie by slot. Leave as 0 to set to default.
**/
UINT16 PcieRpSlotPowerLimitValue[24];
/** Offset 0x0A2C - PCIE RP Upstream Port Transmiter Preset
Used during Gen3 Link Equalization. Used for all lanes. Default is 5.
**/
UINT8 PcieRpUptp[24];
/** Offset 0x0A44 - PCIE RP Downstream Port Transmiter Preset
Used during Gen3 Link Equalization. Used for all lanes. Default is 7.
**/
UINT8 PcieRpDptp[24];
/** Offset 0x0A5C - PCIE RP Enable Port8xh Decode
This member describes whether PCIE root port Port 8xh Decode is enabled. 0: Disable;
1: Enable.
$EN_DIS
**/
UINT8 PcieEnablePort8xhDecode;
/** Offset 0x0A5D - PCIE Port8xh Decode Port Index
The Index of PCIe Port that is selected for Port8xh Decode (0 Based).
**/
UINT8 PchPciePort8xhDecodePortIndex;
/** Offset 0x0A5E - PCH Energy Reporting
Disable/Enable PCH to CPU energy report feature.
$EN_DIS
**/
UINT8 PchPmDisableEnergyReport;
/** Offset 0x0A5F - PCH Sata Test Mode
Allow entrance to the PCH SATA test modes.
$EN_DIS
**/
UINT8 SataTestMode;
/** Offset 0x0A60 - PCH USB OverCurrent mapping lock enable
If this policy option is enabled then BIOS will program OCCFDONE bit in xHCI meaning
that OC mapping data will be consumed by xHCI and OC mapping registers will be locked.
$EN_DIS
**/
UINT8 PchXhciOcLock;
/** Offset 0x0A61
**/
UINT8 UnusedUpdSpace24[17];
/** Offset 0x0A72 - Skip POSTBOOT SAI
Deprecated
$EN_DIS
**/
UINT8 SkipPostBootSai;
/** Offset 0x0A73 - Mctp Broadcast Cycle
Test, Determine if MCTP Broadcast is enabled 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MctpBroadcastCycle;
/** Offset 0x0A74
**/
UINT8 ReservedFspsTestUpd[12];
} FSP_S_TEST_CONFIG;
/** Fsp S UPD Configuration
**/
typedef struct {
/** Offset 0x0000
**/
FSP_UPD_HEADER FspUpdHeader;
/** Offset 0x0020
**/
FSP_S_CONFIG FspsConfig;
/** Offset 0x07AD
**/
FSP_S_TEST_CONFIG FspsTestConfig;
/** Offset 0x0A80
**/
UINT16 UpdTerminator;
} FSPS_UPD;
#pragma pack()
#endif