1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
|
# HP EliteBook 820 G2
This page is about the notebook [HP EliteBook 820 G2].
## Release status
HP EliteBook 820 G2 was released in 2015 and is now end of life.
It can be bought from a secondhand market like Taobao or eBay.
## Required proprietary blobs
The following blobs are required to operate the hardware:
1. EC firmware
2. Intel ME firmware
3. Broadwell mrc.bin and refcode.elf
HP EliteBook 820 G2 uses SMSC MEC1324 as its embedded controller.
The EC firmware is stored in the flash chip, but we don't need to touch it
or use it in the coreboot build process.
Intel ME firmware is in the flash chip. It is not needed when building coreboot.
The Broadwell memory reference code binary and reference code blob is needed
when building coreboot.
## Programming
Before flashing, remove the battery and the hard drive cover according to the
[Maintenance and Service Guide] of this laptop.
HP EliteBook 820 G2 has two flash chips, a 16MiB system flash, and a 2MiB
private flash. To install coreboot, we need to program both flash chips.
Read [HP Sure Start] for detailed information.
To access the system flash, we need to connect the AC adapter to the machine,
then clip on the flash chip with an SOIC-8 clip. An [STM32-based flash programmer]
made with an STM32 development board is tested to work.
To access the private flash chip, we can use a ch341a based flash programmer and
flash the chip with the AC adapter disconnected.
Before flashing coreboot, we need to do the following:
1. Erase the private flash to disable the IFD protection
2. Modify the IFD to shrink the BIOS region, so that we'll not use or override
the protected bootblock and PEI region, as well as the EC firmware
To erase the private flash chip, attach it with the flash programmer via the SOIC-8 clip,
then run:
flashrom -p <programmer> --erase
To modify the IFD, we need a new flash layout. The flash layout of the OEM firmware is:
00000000:00000fff fd
00001000:00002fff gbe
00003000:005fffff me
00600000:00ffffff bios
The default coreboot configuration sets the flash chip size to 12MiB, so set the end of the
BIOS region to 0xbfffff in the new layout. The modified IFD is as follows (Platform Data
region pd is the region protected by HP Sure Start, now we set it to the last 4MiB):
00000000:00000fff fd
00001000:00002fff gbe
00003000:005fffff me
00600000:00bfffff bios
00c00000:00ffffff pd
Write the above layout in a file, and use ifdtool to modify the IFD of a flash image.
Suppose the above layout file is ``layout.txt`` and the origin content of the system flash
is in ``factory-sys.rom``, run:
ifdtool -n layout.txt factory-sys.rom
Then a flash image with a new IFD will be in ``factory-sys.rom.new``.
Flash the IFD of the system flash:
flashrom -p <programmer> --ifd -i fd -w factory-sys.rom.new
Then flash the coreboot image:
# first extend the 12M coreboot.rom to 16M
fallocate -l 16M build/coreboot.rom
flashrom -p <programmer> --ifd -i bios -w build/coreboot.rom
After coreboot is installed, the coreboot firmware can be updated with internal flashing:
flashrom -p internal --ifd -i bios --noverify-all -w build/coreboot.rom
## Debugging
TBD
The board can be debugged with EHCI debug. The EHCI debug port is the USB port on the left.
## Test status
### Known issues
TBD
- No Intel GbE device
- If the laptop has a reboot before, it cannot resume from S3
### Untested
- Touch screen
- NFC module
- SD card reader
- Fingerprint reader
- Smart Card reader
- TPM
### Working
- i3-5010U CPU with 16G+8G memory
- SATA and M.2 SATA disk
- PCIe SSD
- Webcam
- Audio output from speaker and headphone jack
- WLAN
- WWAN
- DisplayPort
- VGA
- Dock
- USB
- Keyboard and touchpad
- EC ACPI
- S3 resume
- Arch Linux with Linux 5.11.16
- Broadwell MRC version 2.6.0 Build 0 and refcode from Purism Librem 13 v1
- Graphics initialization with libgfxinit
- Payload: SeaBIOS
- EC firmware (what version?)
- Internal flashing under coreboot
## Technology
```eval_rst
+------------------+-----------------------------+
| SoC | Intel Broadwell |
+------------------+-----------------------------+
| EC | SMSC MEC1324 |
+------------------+-----------------------------+
| Coprocessor | Intel Management Engine |
+------------------+-----------------------------+
```
[HP EliteBook 820 G2]: https://support.hp.com/us-en/product/HP-EliteBook-820-G2-Notebook-PC/7343192/
[Maintenance and Service Guide]: http://h10032.www1.hp.com/ctg/Manual/c04775894.pdf
[STM32-based flash programmer]: https://github.com/dword1511/stm32-vserprog
[HP Sure Start]: hp_sure_start.md
|
