path: root/src/mainboard/asrock/h110m/devicetree.cb

##
## This file is part of the coreboot project.
##
## Copyright (C) 2017 Intel Corporation.
## Copyright (C) 2019 Maxim Polyakov <max.senia.poliak@gmail.com>
##
## This program is free software; you can redistribute it and/or modify
## it under the terms of the GNU General Public License as published by
## the Free Software Foundation; version 2 of the License.
##
## This program is distributed in the hope that it will be useful,
## but WITHOUT ANY WARRANTY; without even the implied warranty of
## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
## GNU General Public License for more details.
##

chip soc/intel/skylake

	# Enable deep Sx states
	register "deep_s3_enable_ac" = "0"
	register "deep_s3_enable_dc" = "0"
	register "deep_s5_enable_ac" = "0"
	register "deep_s5_enable_dc" = "0"
	register "deep_sx_config" = "DSX_EN_WAKE_PIN"

	register "eist_enable" = "1"

	# GPE configuration
	# Note that GPE events called out in ASL code rely on this
	# route. i.e. If this route changes then the affected GPE
	# offset bits also need to be changed.
	register "gpe0_dw0" = "GPP_B"
	register "gpe0_dw1" = "GPP_D"
	register "gpe0_dw2" = "GPP_E"

	# Enable "Intel Speed Shift Technology"
	register "speed_shift_enable" = "1"

	# Enable DPTF
	register "dptf_enable" = "1"

	# FSP Configuration
	register "SmbusEnable" = "1"
	register "ScsEmmcEnabled" = "0"
	register "ScsEmmcHs400Enabled" = "0"
	register "ScsSdCardEnabled" = "0"
	register "HeciEnabled" = "0"
	register "SkipExtGfxScan" = "0"
	register "PrimaryDisplay" = "Display_PEG"
	register "Device4Enable" = "1"
	register "SaGv" = "SaGv_Enabled"
	register "PmTimerDisabled" = "0"
	register "EnableAzalia" = "1"
	register "DspEnable" = "0"

	register "pirqa_routing" = "PCH_IRQ11"
	register "pirqb_routing" = "PCH_IRQ10"
	register "pirqc_routing" = "PCH_IRQ11"
	register "pirqd_routing" = "PCH_IRQ11"
	register "pirqe_routing" = "PCH_IRQ11"
	register "pirqf_routing" = "PCH_IRQ11"
	register "pirqg_routing" = "PCH_IRQ11"
	register "pirqh_routing" = "PCH_IRQ11"

	# Set LPC Serial IRQ mode
	register "serirq_mode" = "SERIRQ_CONTINUOUS"

	# Enabling SLP_S3#, SLP_S4#, SLP_SUS and SLP_A Stretch
	# SLP_S3 Minimum Assertion Width. Values 0: 60us, 1: 1ms, 2: 50ms, 3: 2s
	register "PmConfigSlpS3MinAssert" = "0x02"

	# SLP_S4 Minimum Assertion Width. Values 0: default, 1: 1s, 2: 2s, 3: 3s, 4: 4s
	register "PmConfigSlpS4MinAssert" = "0x04"

	# SLP_SUS Minimum Assertion Width. Values 0: 0ms, 1: 500ms, 2: 1s, 3: 4s
	register "PmConfigSlpSusMinAssert" = "0x03"

	# SLP_A Minimum Assertion Width. Values 0: 0ms, 1: 4s, 2: 98ms, 3: 2s
	register "PmConfigSlpAMinAssert" = "0x03"

	# VR Settings Configuration for 5 Domains
	#+----------------+-------+-------+-------------+-------------+-------+
	#| Domain/Setting |  SA   |  IA   | Ring Sliced | GT Unsliced |  GT   |
	#+----------------+-------+-------+-------------+-------------+-------+
	#| Psi1Threshold  | 20A   | 20A   | 20A         | 20A         | 20A   |
	#| Psi2Threshold  | 4A    | 5A    | 5A          | 5A          | 5A    |
	#| Psi3Threshold  | 1A    | 1A    | 1A          | 1A          | 1A    |
	#| Psi3Enable     | 1     | 1     | 1           | 1           | 1     |
	#| Psi4Enable     | 1     | 1     | 1           | 1           | 1     |
	#| ImonSlope      | 0     | 0     | 0           | 0           | 0     |
	#| ImonOffset     | 0     | 0     | 0           | 0           | 0     |
	#| IccMax*        | 0     | 0     | 0           | 0           | 0     |
	#| VrVoltageLimit | 1.52V | 1.52V | 1.52V       | 1.52V       | 1.52V |
	#+----------------+-------+-------+-------------+-------------+-------+
	# * - is set automatically for the KBL-S/KBL-DT CPUs in the vr_config.c
	register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
		.vr_config_enable = 1, \
		.psi1threshold = 0x50, \
		.psi2threshold = 0x10, \
		.psi3threshold = 0x4, \
		.psi3enable = 1, \
		.psi4enable = 1, \
		.imon_slope = 0x0, \
		.imon_offset = 0x0, \
		.icc_max = 0x0, \
		.voltage_limit = 1520 \
	}"

	register "domain_vr_config[VR_IA_CORE]" = "{
		.vr_config_enable = 1, \
		.psi1threshold = 0x50, \
		.psi2threshold = 0x14, \
		.psi3threshold = 0x4, \
		.psi3enable = 1, \
		.psi4enable = 1, \
		.imon_slope = 0x0, \
		.imon_offset = 0x0, \
		.icc_max = 0x0, \
		.voltage_limit = 1520 \
	}"

	register "domain_vr_config[VR_GT_UNSLICED]" = "{
		.vr_config_enable = 1, \
		.psi1threshold = 0x50, \
		.psi2threshold = 0x14, \
		.psi3threshold = 0x4, \
		.psi3enable = 1, \
		.psi4enable = 1, \
		.imon_slope = 0x0, \
		.imon_offset = 0x0, \
		.icc_max = 0x0 ,\
		.voltage_limit = 1520 \
	}"

	register "domain_vr_config[VR_GT_SLICED]" = "{
		.vr_config_enable = 1, \
		.psi1threshold = 0x50, \
		.psi2threshold = 0x14, \
		.psi3threshold = 0x4, \
		.psi3enable = 1, \
		.psi4enable = 1, \
		.imon_slope = 0x0, \
		.imon_offset = 0x0, \
		.icc_max = 0x0, \
		.voltage_limit = 1520 \
	}"

	register "EnableLan" = "0"
	register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8"  # I2C4 is 1.8V

	register "PmTimerDisabled" = "0"

	# USB
	register "usb2_ports[0]" = "USB2_PORT_MID(OC0)"
	register "usb2_ports[1]" = "USB2_PORT_MID(OC0)"
	register "usb2_ports[2]" = "USB2_PORT_MID(OC4)"
	register "usb2_ports[3]" = "USB2_PORT_MID(OC4)"
	register "usb2_ports[4]" = "USB2_PORT_MID(OC2)"
	register "usb2_ports[5]" = "USB2_PORT_MID(OC2)"
	register "usb2_ports[6]" = "USB2_PORT_MID(OC0)"
	register "usb2_ports[7]" = "USB2_PORT_MID(OC0)"
	register "usb2_ports[8]" = "USB2_PORT_MID(OC0)"
	register "usb2_ports[9]" = "USB2_PORT_MID(OC0)"
	register "usb2_ports[10]" = "USB2_PORT_MID(OC1)"
	register "usb2_ports[11]" = "USB2_PORT_MID(OC1)"
	register "usb2_ports[12]" = "USB2_PORT_MID(OC_SKIP)"
	register "usb2_ports[13]" = "USB2_PORT_MID(OC_SKIP)"
	register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)"
	register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC0)"
	register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC3)"
	register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)"
	register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC1)"
	register "usb3_ports[5]" = "USB3_PORT_DEFAULT(OC1)"
	register "usb3_ports[6]" = "USB3_PORT_DEFAULT(OC_SKIP)"
	register "usb3_ports[7]" = "USB3_PORT_DEFAULT(OC_SKIP)"
	register "usb3_ports[8]" = "USB3_PORT_DEFAULT(OC_SKIP)"
	register "usb3_ports[9]" = "USB3_PORT_DEFAULT(OC_SKIP)"

	# SATA
	register "EnableSata" = "1"
	register "SataSalpSupport" = "1"
	register "SataPortsEnable" = "{ \
		[0]     = 1, \
		[1]     = 1, \
		[2]     = 1, \
		[3]     = 1, \
		[4]     = 1, \
		[5]     = 1, \
		[6]     = 1, \
		[7]     = 1, \
	}"

	# PCH UART, SPI, I2C
	register "SerialIoDevMode" = "{ \
		[PchSerialIoIndexI2C0]  = PchSerialIoPci, \
		[PchSerialIoIndexI2C1]  = PchSerialIoPci, \
		[PchSerialIoIndexI2C2]  = PchSerialIoDisabled, \
		[PchSerialIoIndexI2C3]  = PchSerialIoDisabled, \
		[PchSerialIoIndexI2C4]  = PchSerialIoDisabled, \
		[PchSerialIoIndexI2C5]  = PchSerialIoDisabled, \
		[PchSerialIoIndexSpi0]  = PchSerialIoPci, \
		[PchSerialIoIndexSpi1]  = PchSerialIoDisabled, \
		[PchSerialIoIndexUart0] = PchSerialIoDisabled, \
		[PchSerialIoIndexUart1] = PchSerialIoDisabled, \
		[PchSerialIoIndexUart2] = PchSerialIoDisabled, \
	}"

	# Set params for PEG 0:1:0
	register "Peg0MaxLinkWidth" = "Peg0_x16"
	# Configure PCIe clockgen in PCH
	# PEG0 uses SRCCLKREQ0 and CLKSRC0
	register "PcieRpClkReqSupport[0]" = "1"
	register "PcieRpClkReqNumber[0]" = "0"
	register "PcieRpClkSrcNumber[0]" = "0"

	# Enable Root port 6(x1) for LAN.
	register "PcieRpEnable[5]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[5]" = "1"
	# Use SRCCLKREQ1#
	register "PcieRpClkReqNumber[5]" = "1"
	# Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[5]" = "1"
	# Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[5]" = "1"
	# Use CLK SRC 1
	register "PcieRpClkSrcNumber[5]" = "1"

	# Enable Root port 5 (x1) for PCIE slot.
	register "PcieRpEnable[4]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[4]" = "1"
	# Use SRCCLKREQ2#
	register "PcieRpClkReqNumber[4]" = "2"
	# Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[4]" = "1"
	# Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[4]" = "1"
	# Use CLK SRC 2
	register "PcieRpClkSrcNumber[4]" = "2"
	# Use Hot Plug subsystem
	register "PcieRpHotPlug[4]" = "1"

	# Enable Root port 7(x1) for PCIE slot.
	register "PcieRpEnable[6]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[6]" = "1"
	# Use SRCCLKREQ3#
	register "PcieRpClkReqNumber[6]" = "3"
	# Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[6]" = "1"
	# Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[6]" = "1"
	# Use CLK SRC 3
	register "PcieRpClkSrcNumber[6]" = "3"
	# Use Hot Plug subsystem
	register "PcieRpHotPlug[6]" = "1"

	# PL2 override 91W
	register "tdp_pl2_override" = "91"

	# Send an extra VR mailbox command for the PS4 exit issue
	register "SendVrMbxCmd" = "2"

	device cpu_cluster 0 on
		device lapic 0 on end
	end
	device domain 0 on
		device pci 00.0 on # Host Bridge
			subsystemid 0x1849 0x191f
		end
		device pci 01.0 on # PEG
			subsystemid 0x1849 0x1901
		end
		device pci 02.0 on # Integrated Graphics Device
			subsystemid 0x1849 0x1912
		end
		device pci 14.0 on # USB xHCI
			subsystemid 0x1849 0xa131
		end
		device pci 14.1 off end # USB xDCI (OTG)
		device pci 14.2 on # Thermal Subsystem
			subsystemid 0x1849 0xa131
		end
		device pci 15.0 off end # I2C #0
		device pci 15.1 off end # I2C #1
		device pci 15.2 off end # I2C #2
		device pci 15.3 off end # I2C #3
		device pci 16.0 on # Management Engine Interface 1
			subsystemid 0x1849 0xa131
		end
		device pci 16.1 off end # Management Engine Interface 2
		device pci 16.2 off end # Management Engine IDE-R
		device pci 16.3 off end # Management Engine KT Redirection
		device pci 16.4 off end # Management Engine Interface 3
		device pci 17.0 on # SATA
			subsystemid 0x1849 0xa102
		end
		device pci 19.0 off end # UART #2
		device pci 19.1 off end # I2C #5
		device pci 19.2 off end # I2C #4
		device pci 1c.0 on  end # PCI Express Port 1
		device pci 1c.1 off end # PCI Express Port 2
		device pci 1c.2 off end # PCI Express Port 3
		device pci 1c.3 off end # PCI Express Port 4
		device pci 1c.4 on  end # PCI Express Port 5
		device pci 1c.5 on  end # PCI Express Port 6
		device pci 1c.6 on  end # PCI Express Port 7
		device pci 1c.7 off end # PCI Express Port 8
		device pci 1d.0 off end # PCI Express Port 9
		device pci 1d.1 off end # PCI Express Port 10
		device pci 1d.2 off end # PCI Express Port 11
		device pci 1d.3 off end # PCI Express Port 12
		device pci 1e.0 off end # UART #0
		device pci 1e.1 off end # UART #1
		device pci 1e.2 off end # GSPI #0
		device pci 1e.3 off end # GSPI #1
		device pci 1e.4 off end # eMMC
		device pci 1e.5 off end # SDIO
		device pci 1e.6 off end # SDCard
		device pci 1f.0 on # LPC bridge
			subsystemid 0x1849 0x1a43
			chip superio/nuvoton/nct6791d
				device pnp 2e.0   off end # Floppy
				device pnp 2e.1   on      # Parallel
					# global
					irq 0x1c = 0x10
					irq 0x27 = 0x10
					irq 0x2a = 0x64
					# parallel port
					io  0x60 = 0x0378
					irq 0x70 = 7
					drq 0x74 = 4      # No DMA
					irq 0xf0 = 0x3c   # Printer mode
				end
				device pnp 2e.2   on      # UART A
					io  0x60 = 0x03f8
					irq 0x70 = 4
				end
				device pnp 2e.3   on      # IR
					io  0x60 = 0x02f8
					irq 0x70 = 3
				end
				device pnp 2e.5   on      # PS/2 KBC
					io  0x60 = 0x0060
					io  0x62 = 0x0064
					irq 0x70 = 1      # Keyboard
					irq 0x72 = 12     # Mouse
				end
				device pnp 2e.6   off end # CIR
				device pnp 2e.7   off end # GPIO6
				device pnp 2e.107 off end # GPIO7
				device pnp 2e.207 off end # GPIO8
				device pnp 2e.8   off end # WDT
				device pnp 2e.108 off end # GPIO0
				device pnp 2e.308 off end # GPIO base
				device pnp 2e.408 off end # WDTMEM
				device pnp 2e.708 off end # GPIO1
				device pnp 2e.9   off end # GPIO2
				device pnp 2e.109 off end # GPIO3
				device pnp 2e.209 off end # GPIO4
				device pnp 2e.309 off end # GPIO5
				device pnp 2e.a   off end # ACPI
				device pnp 2e.b   on      # HWM, LED
					io  0x60 = 0x0290
					io  0x62 = 0
					irq 0x70 = 0
				end
				device pnp 2e.d   off end # BCLK, WDT2, WDT_MEM
				device pnp 2e.e   off end # CIR wake-up
				device pnp 2e.f   off end # GPIO PP/OD
				device pnp 2e.14  off end # SVID, Port 80 UART
				device pnp 2e.16  off end # DS5
				device pnp 2e.116 off end # DS3
				device pnp 2e.316 off end # PCHDSW
				device pnp 2e.416 off end # DSWWOPT
				device pnp 2e.516 off end # DS3OPT
				device pnp 2e.616 off end # DSDSS
				device pnp 2e.716 off end # DSPU
			end     # superio/nuvoton/nct6791d
			chip drivers/pc80/tpm
				device pnp 4e.0 on end  # TPM module
			end
		end # LPC Interface
		device pci 1f.1 on  end # P2SB
		device pci 1f.2 on  end # Power Management Controller
		device pci 1f.3 on  end # Intel HDA
		device pci 1f.4 on  end # SMBus
		device pci 1f.5 on  end # PCH SPI
		device pci 1f.6 off end # GbE
	end
end