summaryrefslogtreecommitdiff
path: root/src/mainboard/cubietech/cubieboard/bootblock.c
blob: 2e5929c019b3f7494293492ca61eaa230f24e80b (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
/*
 * Minimal bootblock for Cubieboard
 * It sets up CPU clock, and enables the bootblock console.
 *
 * Copyright (C) 2013  Alexandru Gagniuc <mr.nuke.me@gmail.com>
 * Subject to the GNU GPL v2, or (at your option) any later version.
 */

#include <arch/io.h>
#include <uart.h>
#include <console/console.h>
#include <delay.h>
#include <cpu/allwinner/a10/gpio.h>
#include <cpu/allwinner/a10/clock.h>
#include <cpu/allwinner/a10/dramc.h>

#define CPU_AHB_APB0_DEFAULT 		\
	 CPU_CLK_SRC_OSC24M	 	\
	 | APB0_DIV_1			\
	 | AHB_DIV_2			\
	 | AXI_DIV_1

#define GPH_STATUS_LEDS			(1 << 20) | (1 << 21)
#define GPH_LED1_PIN_NO			21
#define GPH_LED2_PIN_NO			20

#define GPB_UART0_FUNC			2
#define GPB_UART0_PINS			((1 << 22) | (1 << 23))

static void cubieboard_set_sys_clock(void)
{
	u32 reg32;
	struct a10_ccm *ccm = (void *)A1X_CCM_BASE;

	/* Switch CPU clock to main oscillator */
	write32(CPU_AHB_APB0_DEFAULT, &ccm->cpu_ahb_apb0_cfg);

	/* Configure the PLL1. The value is the same one used by u-boot
	 * P = 1, N = 16, K = 1, M = 1 --> Output = 384 MHz
	 */
	write32(0xa1005000, &ccm->pll1_cfg);

	/* FIXME: Delay to wait for PLL to lock */
	u32 wait = 1000;
	while (--wait);

	/* Switch CPU to PLL clock */
	reg32 = read32(&ccm->cpu_ahb_apb0_cfg);
	reg32 &= ~CPU_CLK_SRC_MASK;
	reg32 |= CPU_CLK_SRC_PLL1;
	write32(reg32, &ccm->cpu_ahb_apb0_cfg);
}

static void cubieboard_setup_clocks(void)
{
	struct a10_ccm *ccm = (void *)A1X_CCM_BASE;

	cubieboard_set_sys_clock();
	/* Configure the clock source for APB1. This drives our UART */
	write32(APB1_CLK_SRC_OSC24M | APB1_RAT_N(0) | APB1_RAT_M(0),
		&ccm->apb1_clk_div_cfg);

}

static void cubieboard_setup_gpios(void)
{
	/* Mux Status LED pins */
	gpio_set_multipin_func(GPH, GPH_STATUS_LEDS, GPIO_PIN_FUNC_OUTPUT);
	/* Turn on green LED to let user know we're executing coreboot code */
	gpio_set(GPH, GPH_LED2_PIN_NO);

	/* Mux UART pins */
	gpio_set_multipin_func(GPB, GPB_UART0_PINS, GPB_UART0_FUNC);
}

static void cubieboard_enable_uart(void)
{
	a1x_periph_clock_enable(A1X_CLKEN_UART0);
}

static void cubieboard_raminit(void)
{
	struct dram_para dram_para = {
		.clock = 480,
		.type = 3,
		.rank_num = 1,
		.density = 4096,
		.io_width = 16,
		.bus_width = 32,
		.cas = 6,
		.zq = 123,
		.odt_en = 0,
		.size = 1024,
		.tpr0 = 0x30926692,
		.tpr1 = 0x1090,
		.tpr2 = 0x1a0c8,
		.tpr3 = 0,
		.tpr4 = 0,
		.tpr5 = 0,
		.emr1 = 0,
		.emr2 = 0,
		.emr3 = 0,
	};

	dramc_init(&dram_para);

	/* FIXME: ram_check does not compile for ARM,
	 * and we didn't init console yet
	 */
	////void *const test_base = (void *)A1X_DRAM_BASE;
	////ram_check((u32)test_base, (u32)test_base + 0x1000);
}

void bootblock_mainboard_init(void);
void bootblock_mainboard_init(void)
{
	/* A10 Timer init uses the 24MHz clock, not PLLs, so we can init it very
	 * early on to get udelay, which is used almost everywhere else.
	 */
	init_timer();

	cubieboard_setup_clocks();
	cubieboard_setup_gpios();
	cubieboard_enable_uart();

	cubieboard_raminit();
}