1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
|
/*
* Minimal bootblock for Cubieboard
* It sets up CPU clock, and enables the bootblock console.
*
* Copyright (C) 2013 Alexandru Gagniuc <mr.nuke.me@gmail.com>
* Subject to the GNU GPL v2, or (at your option) any later version.
*/
#include <arch/io.h>
#include <bootblock_common.h>
#include <console/uart.h>
#include <console/console.h>
#include <delay.h>
#include <cpu/allwinner/a10/gpio.h>
#include <cpu/allwinner/a10/clock.h>
#include <cpu/allwinner/a10/dramc.h>
#define CPU_AHB_APB0_DEFAULT \
CPU_CLK_SRC_OSC24M \
| APB0_DIV_1 \
| AHB_DIV_2 \
| AXI_DIV_1
#define GPH_STATUS_LEDS (1 << 20) | (1 << 21)
#define GPH_LED1_PIN_NO 21
#define GPH_LED2_PIN_NO 20
#define GPB_UART0_FUNC 2
#define GPB_UART0_PINS ((1 << 22) | (1 << 23))
#define GPF_SD0_FUNC 2
#define GPF_SD0_PINS 0x3f /* PF0 thru PF5 */
#define GPH1_SD0_DET_FUNC 5
static void cubieboard_set_sys_clock(void)
{
u32 reg32;
struct a10_ccm *ccm = (void *)A1X_CCM_BASE;
/* Switch CPU clock to main oscillator */
writel(CPU_AHB_APB0_DEFAULT, &ccm->cpu_ahb_apb0_cfg);
/* Configure the PLL1. The value is the same one used by u-boot
* P = 1, N = 16, K = 1, M = 1 --> Output = 384 MHz
*/
writel(0xa1005000, &ccm->pll1_cfg);
/* FIXME: Delay to wait for PLL to lock */
u32 wait = 1000;
while (--wait);
/* Switch CPU to PLL clock */
reg32 = read32(&ccm->cpu_ahb_apb0_cfg);
reg32 &= ~CPU_CLK_SRC_MASK;
reg32 |= CPU_CLK_SRC_PLL1;
writel(reg32, &ccm->cpu_ahb_apb0_cfg);
}
static void cubieboard_setup_clocks(void)
{
struct a10_ccm *ccm = (void *)A1X_CCM_BASE;
cubieboard_set_sys_clock();
/* Configure the clock source for APB1. This drives our UART */
writel(APB1_CLK_SRC_OSC24M | APB1_RAT_N(0) | APB1_RAT_M(0),
&ccm->apb1_clk_div_cfg);
/* Configure the clock for SD0 */
writel(SDx_CLK_GATE | SDx_CLK_SRC_OSC24M | SDx_RAT_EXP_N(0) | SDx_RAT_M(1),
&ccm->sd0_clk_cfg);
/* Enable clock to SD0 */
a1x_periph_clock_enable(A1X_CLKEN_MMC0);
}
static void cubieboard_setup_gpios(void)
{
/* Mux Status LED pins */
gpio_set_multipin_func(GPH, GPH_STATUS_LEDS, GPIO_PIN_FUNC_OUTPUT);
/* Turn on green LED to let user know we're executing coreboot code */
gpio_set(GPH, GPH_LED2_PIN_NO);
/* Mux UART pins */
gpio_set_multipin_func(GPB, GPB_UART0_PINS, GPB_UART0_FUNC);
/* Mux SD pins */
gpio_set_multipin_func(GPF, GPF_SD0_PINS, GPF_SD0_FUNC);
gpio_set_pin_func(GPH, 1, GPH1_SD0_DET_FUNC);
}
static void cubieboard_enable_uart(void)
{
a1x_periph_clock_enable(A1X_CLKEN_UART0);
}
static void cubieboard_raminit(void)
{
struct dram_para dram_para = {
.clock = 480,
.type = 3,
.rank_num = 1,
.density = 4096,
.io_width = 16,
.bus_width = 32,
.cas = 6,
.zq = 123,
.odt_en = 0,
.size = 1024,
.tpr0 = 0x30926692,
.tpr1 = 0x1090,
.tpr2 = 0x1a0c8,
.tpr3 = 0,
.tpr4 = 0,
.tpr5 = 0,
.emr1 = 0,
.emr2 = 0,
.emr3 = 0,
};
dramc_init(&dram_para);
/* FIXME: ram_check does not compile for ARM,
* and we didn't init console yet
*/
////void *const test_base = (void *)A1X_DRAM_BASE;
////ram_check((u32)test_base, (u32)test_base + 0x1000);
}
void bootblock_mainboard_init(void)
{
/* A10 Timer init uses the 24MHz clock, not PLLs, so we can init it very
* early on to get udelay, which is used almost everywhere else.
*/
init_timer();
cubieboard_setup_clocks();
cubieboard_setup_gpios();
cubieboard_enable_uart();
cubieboard_raminit();
}
|
