summaryrefslogtreecommitdiff
path: root/src/southbridge/amd/sb700/early_setup.c
blob: ddba1a8438ca513b7b04996c6130e760ead5a12e (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
/*
 * This file is part of the coreboot project.
 *
 * Copyright (C) 2010 Advanced Micro Devices, Inc.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; version 2 of the License.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
 */

#ifndef _SB700_EARLY_SETUP_C_
#define _SB700_EARLY_SETUP_C_

#include <stdint.h>
#include <arch/cpu.h>
#include <arch/io.h>
#include <console/console.h>
#include <cpu/x86/msr.h>

#include <reset.h>
#include <arch/cpu.h>
#include <cbmem.h>
#include "sb700.h"
#include "smbus.h"

static void pmio_write(u8 reg, u8 value)
{
	outb(reg, PM_INDEX);
	outb(value, PM_INDEX + 1);
}

static u8 pmio_read(u8 reg)
{
	outb(reg, PM_INDEX);
	return inb(PM_INDEX + 1);
}

static void sb700_acpi_init(void)
{
	u16 word;
	pmio_write(0x20, ACPI_PM_EVT_BLK & 0xFF);
	pmio_write(0x21, ACPI_PM_EVT_BLK >> 8);
	pmio_write(0x22, ACPI_PM1_CNT_BLK & 0xFF);
	pmio_write(0x23, ACPI_PM1_CNT_BLK >> 8);
	pmio_write(0x24, ACPI_PM_TMR_BLK & 0xFF);
	pmio_write(0x25, ACPI_PM_TMR_BLK >> 8);
	pmio_write(0x28, ACPI_GPE0_BLK & 0xFF);
	pmio_write(0x29, ACPI_GPE0_BLK >> 8);

	/* CpuControl is in \_PR.CPU0, 6 bytes */
	pmio_write(0x26, ACPI_CPU_CONTROL & 0xFF);
	pmio_write(0x27, ACPI_CPU_CONTROL >> 8);

	pmio_write(0x2A, 0);	/* AcpiSmiCmdLo */
	pmio_write(0x2B, 0);	/* AcpiSmiCmdHi */

	pmio_write(0x2C, ACPI_PMA_CNT_BLK & 0xFF);
	pmio_write(0x2D, ACPI_PMA_CNT_BLK >> 8);

	pmio_write(0x0E, 1<<3 | 0<<2); /* AcpiDecodeEnable, When set, SB uses
					* the contents of the PM registers at
					* index 20-2B to decode ACPI I/O address.
					* AcpiSmiEn & SmiCmdEn*/
	pmio_write(0x10, 1<<1 | 1<<3| 1<<5); /* RTC_En_En, TMR_En_En, GBL_EN_EN */
	word = inl(ACPI_PM1_CNT_BLK);
	word |= 1;
	outl(word, ACPI_PM1_CNT_BLK);		  /* set SCI_EN */
}

/* RPR 2.28: Get SB ASIC Revision. */
static u8 set_sb700_revision(void)
{
	device_t dev;
	u8 rev_id, enable_14Mhz, byte;
	u8 rev = 0;

	/* if (rev != 0) return rev; */

	dev = pci_locate_device(PCI_ID(0x1002, 0x4385), 0);

	if (dev == PCI_DEV_INVALID) {
		die("SMBUS controller not found\n");
		/* NOT REACHED */
	}
	rev_id =  pci_read_config8(dev, 0x08);

	if (rev_id == 0x39) {
		enable_14Mhz = (pmio_read(0x53) >> 6) & 1;
		if (enable_14Mhz == 0x0)
			rev = 0x11;	/* A11 */
		else if (enable_14Mhz == 0x1) {
			/* This happens, if does, only once. So later if we need to get
			 * the revision ID, we don't have to make such a big function.
			 * We just get reg 0x8 in smbus dev. 0x39 is A11, 0x3A is A12. */
			rev = 0x12;
			byte = pci_read_config8(dev, 0x40);
			byte |= 1 << 0;
			pci_write_config8(dev, 0x40, byte);

			pci_write_config8(dev, 0x08, 0x3A); /* Change 0x39 to 0x3A. */

			byte &= ~(1 << 0);
			pci_write_config8(dev, 0x40, byte);
		}
	} else if (rev_id == 0x3A) { /* A12 will be 0x3A after BIOS is initialized */
		rev = 0x12;
	} else if (rev_id == 0x3C) {
		rev = 0x14;
	} else if (rev_id == 0x3D) {
		rev = 0x15;
	} else
		die("It is not SB700 or SB710\n");

	return rev;
}

/***************************************
* Legacy devices are mapped to LPC space.
*	Serial port 0
*	KBC Port
*	ACPI Micro-controller port
*	This function does not change port 0x80 decoding.
*	Console output through any port besides 0x3f8 is unsupported.
*	If you use FWH ROMs, you have to setup IDSEL.
***************************************/
void sb7xx_51xx_lpc_init(void)
{
	u8 reg8;
	u32 reg32;
	device_t dev;

	dev = pci_locate_device(PCI_ID(0x1002, 0x4385), 0);	/* SMBUS controller */
	/* NOTE: Set BootTimerDisable, otherwise it would keep rebooting!!
	 * This bit has no meaning if debug strap is not enabled. So if the
	 * board keeps rebooting and the code fails to reach here, we could
	 * disable the debug strap first. */
	reg32 = pci_read_config32(dev, 0x4C);
	reg32 |= 1 << 31;
	pci_write_config32(dev, 0x4C, reg32);

	/* Enable lpc controller */
	reg32 = pci_read_config32(dev, 0x64);
	reg32 |= 1 << 20;
	pci_write_config32(dev, 0x64, reg32);

#if CONFIG_SOUTHBRIDGE_AMD_SUBTYPE_SP5100
	post_code(0x66);
	dev = pci_locate_device(PCI_ID(0x1002, 0x439d), 0);     /* LPC Controller */
	reg8 = pci_read_config8(dev, 0xBB);
	reg8 |= 1 << 2 | 1 << 3 | 1 << 6 | 1 << 7;
	reg8 &= ~(1 << 1);
	pci_write_config8(dev, 0xBB, reg8);
#endif

	dev = pci_locate_device(PCI_ID(0x1002, 0x439d), 0);	/* LPC Controller */
	/* Decode port 0x3f8-0x3ff (Serial 0) */
	// XXX Serial port decode on LPC is hardcoded to 0x3f8
	reg8 = pci_read_config8(dev, 0x44);
	reg8 |= 1 << 6;
#if CONFIG_SOUTHBRIDGE_AMD_SUBTYPE_SP5100
#if CONFIG_TTYS0_BASE == 0x2f8
	reg8 |= 1 << 7;
#endif
#endif
	pci_write_config8(dev, 0x44, reg8);

	/* Decode port 0x60 & 0x64 (PS/2 keyboard) and port 0x62 & 0x66 (ACPI)*/
	reg8 = pci_read_config8(dev, 0x47);
	reg8 |= (1 << 5) | (1 << 6);
	pci_write_config8(dev, 0x47, reg8);

	/* Enable PrefetchEnSPIFromHost to speed up SPI flash read (does not affect LPC) */
	reg8 = pci_read_config8(dev, 0xbb);
	reg8 |= 1 << 0;
	pci_write_config8(dev, 0xbb, reg8);

	/* Super I/O, RTC */
	reg8 = pci_read_config8(dev, 0x48);
	/* Decode ports 0x2e-0x2f, 0x4e-0x4f (SuperI/O configuration) */
	reg8 |= (1 << 1) | (1 << 0);
	/* Decode port 0x70-0x73 (RTC) */
	reg8 |= (1 << 6);
	pci_write_config8(dev, 0x48, reg8);
}

void sb7xx_51xx_enable_wideio(u8 wio_index, u16 base)
{
	/* TODO: Now assume wio_index=0 */
	device_t dev;
	u8 reg8;

	dev = pci_locate_device(PCI_ID(0x1002, 0x439d), 0);	/* LPC Controller */
	pci_write_config32(dev, 0x64, base);
	reg8 = pci_read_config8(dev, 0x48);
	reg8 |= 1 << 2;
	pci_write_config8(dev, 0x48, reg8);
}

void sb7xx_51xx_disable_wideio(u8 wio_index)
{
	/* TODO: Now assume wio_index=0 */
	device_t dev;
	u8 reg8;

	dev = pci_locate_device(PCI_ID(0x1002, 0x439d), 0);	/* LPC Controller */
	pci_write_config32(dev, 0x64, 0);
	reg8 = pci_read_config8(dev, 0x48);
	reg8 &= ~(1 << 2);
	pci_write_config8(dev, 0x48, reg8);
}

/* what is its usage? */
u32 __attribute__ ((weak)) get_sbdn(u32 bus)
{
	device_t dev;

	/* Find the device. */
	dev = pci_locate_device_on_bus(PCI_ID(0x1002, 0x4385), bus);
	return (dev >> 15) & 0x1f;
}

static u8 dual_core(void)
{
	return (pci_read_config32(PCI_DEV(0, 0x18, 3), 0xE8) & (0x3<<12)) != 0;
}

/*
 * RPR 2.4 C-state and VID/FID change for the K8 platform.
 */
void __attribute__((weak)) enable_fid_change_on_sb(u32 sbbusn, u32 sbdn)
{
	u8 byte;
	byte = pmio_read(0x9a);
	byte &= ~0x34;
	if (dual_core())
		byte |= 0x34;
	else
		byte |= 0x04;
	pmio_write(0x9a, byte);

	byte = pmio_read(0x8f);
	byte &= ~0x30;
	byte |= 0x20;
	pmio_write(0x8f, byte);

	pmio_write(0x8b, 0x01);	/* TODO: if the HT Link is 200 MHz, it is 0x0A. It doesnt often happen. */
	pmio_write(0x8a, 0x90);

	pmio_write(0x88, 0x10);

	byte = pmio_read(0x7c);
	byte |= 0x03;
	pmio_write(0x7c, byte);

	/* Must be 0 for K8 platform. */
	byte = pmio_read(0x68);
	byte &= ~0x01;
	pmio_write(0x68, byte);
	/* Must be 0 for K8 platform. */
	byte = pmio_read(0x8d);
	byte &= ~(1<<6);
	pmio_write(0x8d, byte);

	byte = pmio_read(0x61);
	byte &= ~0x04;
	pmio_write(0x61, byte);

	byte = pmio_read(0x42);
	byte &= ~0x04;
	pmio_write(0x42, byte);

	pmio_write(0x89, 0x10);

	/* Toggle the LDT_STOP# during FID/VID Change, this bit is documented
	   only in SB600!
	   While here, enable C states too
	*/
	pmio_write(0x67, 0x6);
}

void sb7xx_51xx_pci_port80(void)
{
	u8 byte;
	device_t dev;

	/* P2P Bridge */
	dev = pci_locate_device(PCI_ID(0x1002, 0x4384), 0);

	/* Chip Control: Enable subtractive decoding */
	byte = pci_read_config8(dev, 0x40);
	byte |= 1 << 5;
	pci_write_config8(dev, 0x40, byte);

	/* Misc Control: Enable subtractive decoding if 0x40 bit 5 is set */
	byte = pci_read_config8(dev, 0x4B);
	byte |= 1 << 7;
	pci_write_config8(dev, 0x4B, byte);

	/* The same IO Base and IO Limit here is meaningful because we set the
	 * bridge to be subtractive. During early setup stage, we have to make
	 * sure that data can go through port 0x80.
	 */
	/* IO Base: 0xf000 */
	byte = pci_read_config8(dev, 0x1C);
	byte |= 0xF << 4;
	pci_write_config8(dev, 0x1C, byte);

	/* IO Limit: 0xf000 */
	byte = pci_read_config8(dev, 0x1D);
	byte |= 0xF << 4;
	pci_write_config8(dev, 0x1D, byte);

	/* PCI Command: Enable IO response */
	byte = pci_read_config8(dev, 0x04);
	byte |= 1 << 0;
	pci_write_config8(dev, 0x04, byte);

	/* LPC controller */
	dev = pci_locate_device(PCI_ID(0x1002, 0x439D), 0);

	byte = pci_read_config8(dev, 0x4A);
	byte &= ~(1 << 5);	/* disable lpc port 80 */
	pci_write_config8(dev, 0x4A, byte);
}

void sb7xx_51xx_lpc_port80(void)
{
	u8 byte;
	device_t dev;
	u32 reg32;

	/* Enable LPC controller */
	dev = pci_locate_device(PCI_ID(0x1002, 0x4385), 0);
	reg32 = pci_read_config32(dev, 0x64);
	reg32 |= 0x00100000;	/* lpcEnable */
	pci_write_config32(dev, 0x64, reg32);

	/* Enable port 80 LPC decode in pci function 3 configuration space. */
	dev = pci_locate_device(PCI_ID(0x1002, 0x439d), 0);
	byte = pci_read_config8(dev, 0x4a);
	byte |= 1 << 5;		/* enable port 80 */
	pci_write_config8(dev, 0x4a, byte);
}

/* sbDevicesPorInitTable */
static void sb700_devices_por_init(void)
{
	device_t dev;
	u8 byte;
#if CONFIG_SOUTHBRIDGE_AMD_SUBTYPE_SP5100
	u32 dword;
#endif

	printk(BIOS_INFO, "sb700_devices_por_init()\n");
	/* SMBus Device, BDF:0-20-0 */
	printk(BIOS_INFO, "sb700_devices_por_init(): SMBus Device, BDF:0-20-0\n");
	dev = pci_locate_device(PCI_ID(0x1002, 0x4385), 0);

	if (dev == PCI_DEV_INVALID) {
		die("SMBUS controller not found\n");
		/* NOT REACHED */
	}
	printk(BIOS_INFO, "SMBus controller enabled, sb revision is A%x\n",
		    set_sb700_revision());

	/* sbPorAtStartOfTblCfg */
	/* Set A-Link bridge access address. This address is set at device 14h, function 0, register 0xf0.
	 * This is an I/O address. The I/O address must be on 16-byte boundry.  */
	pci_write_config32(dev, 0xf0, AB_INDX);

	/* To enable AB/BIF DMA access, a specific register inside the BIF register space needs to be configured first. */
	/* 4.3:Enables the SB700 to send transactions upstream over A-Link Express interface. */
	axcfg_reg(0x04, 1 << 2, 1 << 2);
	axindxc_reg(0x21, 0xff, 0);

	/* 2.5:Enabling Non-Posted Memory Write for the K8 Platform */
	axindxc_reg(0x10, 1 << 9, 1 << 9);
	/* END of sbPorAtStartOfTblCfg */

	/* sbDevicesPorInitTables */
	/* set smbus iobase */
	pci_write_config32(dev, 0x90, SMBUS_IO_BASE | 1);

	/* enable smbus controller interface */
	byte = pci_read_config8(dev, 0xd2);
	byte |= (1 << 0);
	pci_write_config8(dev, 0xd2, byte);

	/* KB2RstEnable */
	pci_write_config8(dev, 0x40, 0x44);

	/* Enable ISA Address 0-960K decoding */
	pci_write_config8(dev, 0x48, 0x0f);

	/* Enable ISA  Address 0xC0000-0xDFFFF decode */
	pci_write_config8(dev, 0x49, 0xff);

	/* Enable decode cycles to IO C50, C51, C52 GPM controls. */
	byte = pci_read_config8(dev, 0x41);
	byte &= 0x80;
	byte |= 0x33;
	pci_write_config8(dev, 0x41, byte);

	/* Legacy DMA Prefetch Enhancement, CIM masked it. */
	/* pci_write_config8(dev, 0x43, 0x1); */

	/* Disabling Legacy USB Fast SMI# */
	byte = pci_read_config8(dev, 0x62);
	byte |= 0x24;
	pci_write_config8(dev, 0x62, byte);

	/* Configure HPET Counter CLK period */
	byte = pci_read_config8(dev, 0x43);
	byte &= 0xF7;	/* unhide HPET regs */
	pci_write_config8(dev, 0x43, byte);
	pci_write_config32(dev, 0x34, 0x0429B17E ); /* Counter CLK period */
	byte |= 0x08;	/* hide HPET regs */
	pci_write_config8(dev, 0x43, byte);

	/* Features Enable */
	pci_write_config32(dev, 0x64, 0x829E79BF); /* bit10: Enables the HPET interrupt. */

	/* SerialIrq Control */
	pci_write_config8(dev, 0x69, 0x90);

	/* Test Mode, PCIB_SReset_En Mask is set. */
	pci_write_config8(dev, 0x6c, 0x20);

	/* IO Address Enable, CIM set 0x78 only and masked 0x79. */
	/*pci_write_config8(dev, 0x79, 0x4F); */
	pci_write_config8(dev, 0x78, 0xFF);

	/* Set smbus iospace enable, I don't know why write 0x04 into reg5 that is reserved */
	pci_write_config16(dev, 0x4, 0x0407);

	/* clear any lingering errors, so the transaction will run */
	outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);

	/* IDE Device, BDF:0-20-1 */
	printk(BIOS_INFO, "sb700_devices_por_init(): IDE Device, BDF:0-20-1\n");
	dev = pci_locate_device(PCI_ID(0x1002, 0x439C), 0);
	/* Disable prefetch */
	byte = pci_read_config8(dev, 0x63);
	byte |= 0x1;
	pci_write_config8(dev, 0x63, byte);

	/* LPC Device, BDF:0-20-3 */
	printk(BIOS_INFO, "sb700_devices_por_init(): LPC Device, BDF:0-20-3\n");
	dev = pci_locate_device(PCI_ID(0x1002, 0x439D), 0);
	/* DMA enable */
	pci_write_config8(dev, 0x40, 0x04);

	/* IO Port Decode Enable */
	pci_write_config8(dev, 0x44, 0xFF);
	pci_write_config8(dev, 0x45, 0xFF);
	pci_write_config8(dev, 0x46, 0xC3);
	pci_write_config8(dev, 0x47, 0xFF);

	// TODO: This has already been done(?)
	/* IO/Mem Port Decode Enable, I don't know why CIM disable some ports.
	 *  Disable LPC TimeOut counter, enable SuperIO Configuration Port (2e/2f),
	 * Alternate Super I/O Configuration Port (4e/4f), Wide Generic IO Port (64/65). */
	byte = pci_read_config8(dev, 0x48);
	byte |= (1 << 1) | (1 << 0);	/* enable Super IO config port 2e-2h, 4e-4f */
	byte |= 1 << 6;		/* enable for RTC I/O range */
	pci_write_config8(dev, 0x48, byte);
	pci_write_config8(dev, 0x49, 0xFF);
	/* Enable 0x480-0x4bf, 0x4700-0x470B */
	byte = pci_read_config8(dev, 0x4A);
	byte |= ((1 << 1) + (1 << 6));	/*0x42, save the configuraion for port 0x80. */
	pci_write_config8(dev, 0x4A, byte);

	/* Enable Tpm12_en and Tpm_legacy. I don't know what is its usage and copied from CIM. */
	pci_write_config8(dev, 0x7C, 0x05);

	/* P2P Bridge, BDF:0-20-4, the configuration of the registers in this dev are copied from CIM,
	 */
	printk(BIOS_INFO, "sb700_devices_por_init(): P2P Bridge, BDF:0-20-4\n");
	dev = pci_locate_device(PCI_ID(0x1002, 0x4384), 0);

	/* Arbiter enable. */
	pci_write_config8(dev, 0x43, 0xff);

	/* Set PCDMA request into hight priority list. */
	/* pci_write_config8(dev, 0x49, 0x1) */ ;

	pci_write_config8(dev, 0x40, 0x26);

	pci_write_config8(dev, 0x0d, 0x40);
	pci_write_config8(dev, 0x1b, 0x40);
	/* Enable PCIB_DUAL_EN_UP will fix potential problem with PCI cards. */
	pci_write_config8(dev, 0x50, 0x01);

#if CONFIG_SOUTHBRIDGE_AMD_SUBTYPE_SP5100
	/* SP5100 default SATA mode is RAID5 MODE */
	dev = pci_locate_device(PCI_ID(0x1002, 0x4393), 0);
	/* Set SATA Operation Mode, Set to IDE mode */
	byte = pci_read_config8(dev, 0x40);
	byte |= (1 << 0);
	pci_write_config8(dev, 0x40, byte);

	dword = 0x01018f00;
	pci_write_config32(dev, 0x8, dword);

	/* set SATA Device ID writable */
	dword = pci_read_config32(dev, 0x40);
	dword &= ~(1 << 24);
	pci_write_config32(dev, 0x40, dword);

	/* set Device ID accommodate with IDE emulation mode configuration*/
	pci_write_config32(dev, 0x0, 0x43901002);

	/* rpr v2.13 4.17 Reset CPU on Sync Flood */
	abcfg_reg(0x10050, 1 << 2, 1 << 2);
#endif

	/* SATA Device, BDF:0-17-0, Non-Raid-5 SATA controller */
	printk(BIOS_INFO, "sb700_devices_por_init(): SATA Device, BDF:0-18-0\n");
	dev = pci_locate_device(PCI_ID(0x1002, 0x4390), 0);

	/*PHY Global Control*/
	pci_write_config16(dev, 0x86, 0x2C00);
}

/* sbPmioPorInitTable, Pre-initializing PMIO register space
* The power management (PM) block is resident in the PCI/LPC/ISA bridge.
* The PM regs are accessed via IO mapped regs 0xcd6 and 0xcd7.
* The index address is first programmed into IO reg 0xcd6.
* Read or write values are accessed through IO reg 0xcd7.
*/
static void sb700_pmio_por_init(void)
{
	u8 byte;

	printk(BIOS_INFO, "sb700_pmio_por_init()\n");
	/* K8KbRstEn, KB_RST# control for K8 system. */
	byte = pmio_read(0x66);
	byte |= 0x20;
	pmio_write(0x66, byte);

	/* RPR2.31 PM_TURN_OFF_MSG during ASF Shutdown. */
	if (get_sb700_revision(pci_locate_device(PCI_ID(0x1002, 0x4385), 0)) <= 0x12) {
		byte = pmio_read(0x65);
		byte &= ~(1 << 7);
		pmio_write(0x65, byte);

		byte = pmio_read(0x75);
		byte &= 0xc0;
		byte |= 0x05;
		pmio_write(0x75, byte);

		byte = pmio_read(0x52);
		byte &= 0xc0;
		byte |= 0x08;
		pmio_write(0x52, byte);
	} else {
		byte = pmio_read(0xD7);
		byte |= 1 << 0;
		pmio_write(0xD7, byte);

		byte = pmio_read(0x65);
		byte |= 1 << 7;
		pmio_write(0x65, byte);

		byte = pmio_read(0x75);
		byte &= 0xc0;
		byte |= 0x01;
		pmio_write(0x75, byte);

		byte = pmio_read(0x52);
		byte &= 0xc0;
		byte |= 0x02;
		pmio_write(0x52, byte);

	}

	/* Watch Dog Timer Control
	 * Set watchdog time base to 0xfec000f0 to avoid SCSI card boot failure.
	 * But I don't find WDT is enabled in SMBUS 0x41 bit3 in CIM.
	 */
	pmio_write(0x6c, 0xf0);
	pmio_write(0x6d, 0x00);
	pmio_write(0x6e, 0xc0);
	pmio_write(0x6f, 0xfe);

	/* rpr2.15: Enabling Spread Spectrum */
	byte = pmio_read(0x42);
	byte |= 1 << 7;
	pmio_write(0x42, byte);
	/* TODO: Check if it is necessary. IDE reset */
	byte = pmio_read(0xB2);
	byte |= 1 << 0;
	pmio_write(0xB2, byte);
}

/*
* Add any south bridge setting.
*/
static void sb700_pci_cfg(void)
{
	device_t dev;
	u8 byte;

	/* SMBus Device, BDF:0-20-0 */
	dev = pci_locate_device(PCI_ID(0x1002, 0x4385), 0);
	/* Enable watchdog decode timer */
	byte = pci_read_config8(dev, 0x41);
	byte |= (1 << 3);
	pci_write_config8(dev, 0x41, byte);

	/* Set to 1 to reset USB on the software (such as IO-64 or IO-CF9 cycles)
	 * generated PCIRST#. */
	byte = pmio_read(0x65);
	byte |= (1 << 4);
	pmio_write(0x65, byte);

	/* IDE Device, BDF:0-20-1 */
	dev = pci_locate_device(PCI_ID(0x1002, 0x439C), 0);
	/* Enable IDE Explicit prefetch, 0x63[0] clear */
	byte = pci_read_config8(dev, 0x63);
	byte &= 0xfe;
	pci_write_config8(dev, 0x63, byte);

	/* LPC Device, BDF:0-20-3 */
	/* The code below is ported from old chipset. It is not
	 * mentioned in RPR. But I keep them. The registers and the
	 * comments are compatible. */
	dev = pci_locate_device(PCI_ID(0x1002, 0x439D), 0);
	/* Enabling LPC DMA function. */
	byte = pci_read_config8(dev, 0x40);
	byte |= (1 << 2);
	pci_write_config8(dev, 0x40, byte);
	/* Disabling LPC TimeOut. 0x48[7] clear. */
	byte = pci_read_config8(dev, 0x48);
	byte &= 0x7f;
	pci_write_config8(dev, 0x48, byte);
	/* Disabling LPC MSI Capability, 0x78[1] clear. */
	byte = pci_read_config8(dev, 0x78);
	byte &= 0xfd;
	pci_write_config8(dev, 0x78, byte);

	/* SATA Device, BDF:0-17-0, Non-Raid-5 SATA controller */
	dev = pci_locate_device(PCI_ID(0x1002, 0x4390), 0);
	/* rpr7.12 SATA MSI and D3 Power State Capability. */
	byte = pci_read_config8(dev, 0x40);
	byte |= 1 << 0;
	pci_write_config8(dev, 0x40, byte);
	if (get_sb700_revision(pci_locate_device(PCI_ID(0x1002, 0x4385), 0)) <= 0x12)
		pci_write_config8(dev, 0x34, 0x70); /* set 0x61 to 0x70 if S1 is not supported. */
	else
		pci_write_config8(dev, 0x34, 0x50); /* set 0x61 to 0x50 if S1 is not supported. */
	byte &= ~(1 << 0);
	pci_write_config8(dev, 0x40, byte);
}

/*
*/
static void sb700_por_init(void)
{
	/* sbDevicesPorInitTable + sbK8PorInitTable */
	sb700_devices_por_init();

	/* sbPmioPorInitTable + sbK8PmioPorInitTable */
	sb700_pmio_por_init();
}

/*
* It should be called during early POST after memory detection and BIOS shadowing but before PCI bus enumeration.
*/
void sb7xx_51xx_before_pci_init(void)
{
	sb700_pci_cfg();
}

/*
* This function should be called after enable_sb700_smbus().
*/
void sb7xx_51xx_early_setup(void)
{
	printk(BIOS_INFO, "sb700_early_setup()\n");
	sb700_por_init();
	sb700_acpi_init();
}

int s3_save_nvram_early(u32 dword, int size, int  nvram_pos)
{
	int i;
	printk(BIOS_DEBUG, "Writing %x of size %d to nvram pos: %d\n", dword, size, nvram_pos);

	for (i = 0; i<size; i++) {
		outb(nvram_pos, BIOSRAM_INDEX);
		outb((dword >>(8 * i)) & 0xff , BIOSRAM_DATA);
		nvram_pos++;
	}

	return nvram_pos;
}

int s3_load_nvram_early(int size, u32 *old_dword, int nvram_pos)
{
	u32 data = *old_dword;
	int i;
	for (i = 0; i<size; i++) {
		outb(nvram_pos, BIOSRAM_INDEX);
		data &= ~(0xff << (i * 8));
		data |= inb(BIOSRAM_DATA) << (i *8);
		nvram_pos++;
	}
	*old_dword = data;
	printk(BIOS_DEBUG, "Loading %x of size %d to nvram pos:%d\n", *old_dword, size,
		nvram_pos-size);
	return nvram_pos;
}

#if CONFIG_HAVE_ACPI_RESUME
int acpi_is_wakeup_early(void)
{
	u16 tmp;
	tmp = inw(ACPI_PM1_CNT_BLK);
	printk(BIOS_DEBUG, "IN TEST WAKEUP %x\n", tmp);
	return (((tmp & (7 << 10)) >> 10) == 3);
}

unsigned long get_top_of_ram(void)
{
	uint32_t xdata = 0;
	int xnvram_pos = 0xfc, xi;
	if (!acpi_is_wakeup_early())
		return 0;
	for (xi = 0; xi<4; xi++) {
		outb(xnvram_pos, BIOSRAM_INDEX);
		xdata &= ~(0xff << (xi * 8));
		xdata |= inb(BIOSRAM_DATA) << (xi *8);
		xnvram_pos++;
	}
	return (unsigned long) xdata;
}
#endif

#endif