1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
|
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2007 Corey Osgood <corey.osgood@gmail.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#ifndef SOUTHBRIDGE_INTEL_I82801BX_I82801BX_H
#define SOUTHBRIDGE_INTEL_I82801BX_I82801BX_H
#if !defined( __ROMCC__ ) && !defined(__PRE_RAM__)
#include "chip.h"
extern void i82801bx_enable(device_t dev);
#endif
#define PCI_DMA_CFG 0x90
#define SERIRQ_CNTL 0x64
#define GEN_CNTL 0xd0
#define GEN_STS 0xd4
#define RTC_CONF 0xd8
#define GEN_PMCON_3 0xa4
#define PMBASE 0x40
#define PMBASE_ADDR 0x0400 /* ACPI Base Address Register */
#define ACPI_CNTL 0x44
#define BIOS_CNTL 0x4E
#define GPIO_BASE_ICH0_5 0x58 /* LPC GPIO Base Addr. Reg. (ICH0-ICH5) */
#define GPIO_BASE_ICH6_9 0x48 /* LPC GPIO Base Address Register (ICH6-ICH9) */
#define GPIO_CNTL_ICH0_5 0x5C /* LPC GPIO Control Register (ICH0-ICH5) */
#define GPIO_CNTL_ICH6_9 0x4C /* LPC GPIO Control Register (ICH6-ICH9) */
#define PIRQA_ROUT 0x60
#define PIRQB_ROUT 0x61
#define PIRQC_ROUT 0x62
#define PIRQD_ROUT 0x63
#define PIRQE_ROUT 0x68
#define PIRQF_ROUT 0x69
#define PIRQG_ROUT 0x6A
#define PIRQH_ROUT 0x6B
#define FUNC_DIS 0xF2
#define COM_DEC 0xE0 /* LPC I/F Communication Port Decode Ranges (ICH0-ICH5) */
#define LPC_IO_DEC 0x80 /* IO Decode Ranges Register (ICH6-ICH9) */
#define LPC_EN_ICH0_5 0xE6 /* LPC IF Enables Register (ICH0-ICH5) */
#define LPC_EN_ICH6_9 0x82 /* LPC IF Enables Register (ICH6-ICH9) */
#define SBUS_NUM 0x19
#define SUB_BUS_NUM 0x1A
#define SMLT 0x1B
#define IOBASE 0x1C
#define IOLIM 0x1D
#define MEMBASE 0x20
#define MEMLIM 0x22
#define CNF 0x50
#define MTT 0x70
#define PCI_MAST_STS 0x82
#define TCOBASE 0x60 /* TCO Base Address Register */
#define TCO1_CNT 0x08 /* TCO1 Control Register */
/* GEN_PMCON_3 bits */
#define RTC_BATTERY_DEAD (1 << 2)
#define RTC_POWER_FAILED (1 << 1)
#define SLEEP_AFTER_POWER_FAIL (1 << 0)
/* PCI Configuration Space (D31:F1) */
#define IDE_TIM_PRI 0x40 /* IDE timings, primary */
#define IDE_TIM_SEC 0x42 /* IDE timings, secondary */
/* IDE_TIM bits */
#define IDE_DECODE_ENABLE (1 << 15)
/* PCI Configuration Space (D31:F3) */
#define SMB_BASE 0x20
#define HOSTC 0x40
/* HOSTC bits */
#define I2C_EN (1 << 2)
#define SMB_SMI_EN (1 << 1)
#define HST_EN (1 << 0)
/* SMBus I/O bits.
* TODO: Does it matter where we put the SMBus IO base, as long as we keep
* consistent and don't interfere with anything else?
*/
/* #define SMBUS_IO_BASE 0x1000 */
#define SMBUS_IO_BASE 0x0f00
#define SMBHSTSTAT 0x0
#define SMBHSTCTL 0x2
#define SMBHSTCMD 0x3
#define SMBXMITADD 0x4
#define SMBHSTDAT0 0x5
#define SMBHSTDAT1 0x6
#define SMBBLKDAT 0x7
#define SMBTRNSADD 0x9
#define SMBSLVDATA 0xa
#define SMLINK_PIN_CTL 0xe
#define SMBUS_PIN_CTL 0xf
#define SMBUS_TIMEOUT (10 * 1000 * 100)
/* HPET, if present */
#define HPET_ADDR 0xfed0000
#endif /* SOUTHBRIDGE_INTEL_I82801BX_I82801BX_H */
|
