blob: 824d23a0b62dc056e6585e1f20e05562869749f7 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
|
/* the problem: we have 82801dbm support in fb1, and 82801er in fb2.
* fb1 code is what we want, fb2 structure is needed however.
* so we need to get fb1 code for 82801dbm into fb2 structure.
*/
/* What I did: took the 80801er stuff from fb2, verify it against the
* db stuff in fb1, and made sure it was right.
*/
#ifndef I82801DBM_H
#define I82801DBM_H
#include "chip.h"
extern void i82801dbm_enable(device_t dev);
/*
000 = Non-combined. P0 is primary master. P1 is secondary master.
001 = Non-combined. P0 is secondary master. P1 is primary master.
100 = Combined. P0 is primary master. P1 is primary slave. IDE is secondary; Primary IDE channel
disabled.
101 = Combined. P0 is primary slave. P1 is primary master. IDE is secondary.
110 = Combined. IDE is primary. P0 is secondary master. P1 is secondary slave; Secondary IDE
channel disabled.
111 = Combined. IDE is primary. P0 is secondary slave. P1 is secondary master.
*/
#define PCI_DMA_CFG 0x90
#define SERIRQ_CNTL 0x64
#define GEN_CNTL 0xd0
#define GEN_STS 0xd4
#define RTC_CONF 0xd8
#define GEN_PMCON_3 0xa4
#define PCICMD 0x04
#define PMBASE 0x40
#define ACPI_CNTL 0x44
#define BIOS_CNTL 0x4E
#define GPIO_BASE 0x58
#define GPIO_CNTL 0x5C
#define PIRQA_ROUT 0x60
#define PIRQE_ROUT 0x68
#define COM_DEC 0xE0
#define LPC_EN 0xE6
#define FUNC_DIS 0xF2
/* 1e f0 244e */
#define CMD 0x04
#define SBUS_NUM 0x19
#define SUB_BUS_NUM 0x1A
#define SMLT 0x1B
#define IOBASE 0x1C
#define IOLIM 0x1D
#define MEMBASE 0x20
#define MEMLIM 0x22
#define CNF 0x50
#define MTT 0x70
#define PCI_MAST_STS 0x82
#define RTC_FAILED (1 <<2)
#define SMBUS_IO_BASE 0x1000
#define SMBHSTSTAT 0x0
#define SMBHSTCTL 0x2
#define SMBHSTCMD 0x3
#define SMBXMITADD 0x4
#define SMBHSTDAT0 0x5
#define SMBHSTDAT1 0x6
#define SMBBLKDAT 0x7
#define SMBTRNSADD 0x9
#define SMBSLVDATA 0xa
#define SMLINK_PIN_CTL 0xe
#define SMBUS_PIN_CTL 0xf
/* Between 1-10 seconds, We should never timeout normally
* Longer than this is just painful when a timeout condition occurs.
*/
#define SMBUS_TIMEOUT (100*1000)
#endif /* I82801DBM_H */
|
