path: root/src/southbridge/via/vt8231/vt8231.c

#include <arch/io.h>
#include <device/device.h>
#include <device/pci.h>
#include <device/pci_ops.h>
#include <device/pci_ids.h>
#include <device/chip.h>
#include <console/console.h>
#include "vt8231.h"
#include "chip.h"

void pc_keyboard_init(void);

void
hard_reset() {
		printk_err("NO HARD RESET ON VT8231! FIX ME!\n");
}
static void usb_on(int enable)
{
  
  unsigned char regval;

  /* Base 8231 controller */
  device_t dev0 = dev_find_device(PCI_VENDOR_ID_VIA, \
				  PCI_DEVICE_ID_VIA_8231, 0);
  /* USB controller 1 */
  device_t dev2 = dev_find_device(PCI_VENDOR_ID_VIA, \
				  PCI_DEVICE_ID_VIA_82C586_2, 0);
  /* USB controller 2 */
  device_t dev3 = dev_find_device(PCI_VENDOR_ID_VIA, \
				  PCI_DEVICE_ID_VIA_82C586_2, \
				  dev2);

  /* enable USB1 */
  if(dev2) {
    if (enable) {
      pci_write_config8(dev2, 0x3c, 0x05);
      pci_write_config8(dev2, 0x04, 0x07);
    } else {
      pci_write_config8(dev2, 0x3c, 0x00);
      pci_write_config8(dev2, 0x04, 0x00);
    }
  }

  if(dev0) {
    regval = pci_read_config8(dev0, 0x50);
    if (enable) 
      regval &= ~(0x10);    
    else
      regval |= 0x10;    	      
    pci_write_config8(dev0, 0x50, regval);
  }

  /* enable USB2 */
  if(dev3) {
    if (enable) {
      pci_write_config8(dev3, 0x3c, 0x05);
      pci_write_config8(dev3, 0x04, 0x07);
    } else {
      pci_write_config8(dev3, 0x3c, 0x00);
      pci_write_config8(dev3, 0x04, 0x00);
    }
  }

  if(dev0) {
    regval = pci_read_config8(dev0, 0x50);
    if (enable) 
      regval &= ~(0x20);    
    else
      regval |= 0x20;    
    pci_write_config8(dev0, 0x50, regval);
  }

}

static void keyboard_on()
{
  unsigned char regval;

  /* Base 8231 controller */
  device_t dev0 = dev_find_device(PCI_VENDOR_ID_VIA, \
				  PCI_DEVICE_ID_VIA_8231, 0);

  /* kevinh/Ispiri - update entire function to use 
     new pci_write_config8 */

  if (dev0) {
    regval = pci_read_config8(dev0, 0x51);
    regval |= 0x0f; 
    pci_write_config8(dev0, 0x51, regval);
  }
  pc_keyboard_init();

}

static void nvram_on()
{
  /*
   * the VIA 8231 South has a very different nvram setup than the 
   * piix4e ...
   * turn on ProMedia nvram.
   * TO DO: use the PciWriteByte function here.
   */

  /*
   * kevinh/Ispiri - I don't think this is the correct address/value
   * intel_conf_writeb(0x80008841, 0xFF);
   */
}


/*
 * Enable the ethernet device and turn off stepping (because it is integrated 
 * inside the southbridge)
 */
static void ethernet_fixup()
{
  device_t	edev;
  uint8_t		byte;

  printk_info("Ethernet fixup\n");

  edev = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_7, 0);
  if (edev) {
    printk_debug("Configuring VIA LAN\n");

    /* We don't need stepping - though the device supports it */
    byte = pci_read_config8(edev, PCI_COMMAND);
    byte &= ~PCI_COMMAND_WAIT;
    pci_write_config8(edev, PCI_COMMAND, byte);
  } else {
    printk_debug("VIA LAN not found\n");
  }
}


static void vt8231_init(struct southbridge_via_vt8231_config *conf)
{
  unsigned char enables;
  device_t dev0;
  device_t dev1;
  device_t devpwr;

  // to do: use the pcibios_find function here, instead of 
  // hard coding the devfn. 
  // done - kevinh/Ispiri

  /* Base 8231 controller */
  dev0 = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, 0);
  /* IDE controller */
  dev1 = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, \
			 0);
  /* Power management controller */
  devpwr = dev_find_device(PCI_VENDOR_ID_VIA, \
			   PCI_DEVICE_ID_VIA_8231_4, 0);

  // enable the internal I/O decode
  enables = pci_read_config8(dev0, 0x6C);
  enables |= 0x80;
  pci_write_config8(dev0, 0x6C, enables);

  // Map 4MB of FLASH into the address space
  pci_write_config8(dev0, 0x41, 0x7f);

  // Set bit 6 of 0x40, because Award does it (IO recovery time)
  // IMPORTANT FIX - EISA 0x4d0 decoding must be on so that PCI 
  // interrupts can be properly marked as level triggered.
  enables = pci_read_config8(dev0, 0x40);
  pci_write_config8(dev0, 0x40, enables);

  // Set 0x42 to 0xf0 to match Award bios
  enables = pci_read_config8(dev0, 0x42);
  enables |= 0xf0;
  pci_write_config8(dev0, 0x42, enables);

  // Set bit 3 of 0x4a, to match award (dummy pci request)
  enables = pci_read_config8(dev0, 0x4a);
  enables |= 0x08;
  pci_write_config8(dev0, 0x4a, enables);

  // Set bit 3 of 0x4f to match award (use INIT# as cpu reset)
  enables = pci_read_config8(dev0, 0x4f);
  enables |= 0x08;
  pci_write_config8(dev0, 0x4f, enables);

  // Set 0x58 to 0x03 to match Award
  pci_write_config8(dev0, 0x58, 0x03);

  // enable the ethernet/RTC
  if(dev0) {
    enables = pci_read_config8(dev0, 0x51);
    enables |= 0x18; 
    pci_write_config8(dev0, 0x51, enables);
  }
	

  // enable com1 and com2. 
  if (conf->enable_com_ports) {
    enables = pci_read_config8(dev0, 0x6e);

    /* 0x80 is enable com port b, 0x10 is to make it com2, 0x8
     * is enable com port a as com1 kevinh/Ispiri - Old code
     * thought 0x01 would make it com1, that was wrong enables =
     * 0x80 | 0x10 | 0x8 ; pci_write_config8(dev0, 0x6e,
     * enables); // note: this is also a redo of some port of
     * assembly, but we want everything up.
     */

    /* set com1 to 115 kbaud not clear how to do this yet.
     * forget it; done in assembly.
     */

  }
  // enable IDE, since Linux won't do it.
  // First do some more things to devfn (17,0)
  // note: this should already be cleared, according to the book. 
  enables = pci_read_config8(dev0, 0x50);
  printk_debug("IDE enable in reg. 50 is 0x%x\n", enables);
  enables &= ~8; // need manifest constant here!
  printk_debug("set IDE reg. 50 to 0x%x\n", enables);
  pci_write_config8(dev0, 0x50, enables);

  // set default interrupt values (IDE)
  enables = pci_read_config8(dev0, 0x4c);
  printk_debug("IRQs in reg. 4c are 0x%x\n", enables & 0xf);
  // clear out whatever was there. 
  enables &= ~0xf;
  enables |= 4;
  printk_debug("setting reg. 4c to 0x%x\n", enables);
  pci_write_config8(dev0, 0x4c, enables);
	
  // set up the serial port interrupts. 
  // com2 to 3, com1 to 4
  pci_write_config8(dev0, 0x46, 0x04);
  pci_write_config8(dev0, 0x47, 0x03);

  //
  // Power management setup
  //
  // Set ACPI base address to IO 0x4000
  pci_write_config32(devpwr, 0x48, 0x4001);

  // Enable ACPI access (and setup like award)
  pci_write_config8(devpwr, 0x41, 0x84);

  // Set hardware monitor base address to IO 0x6000
  pci_write_config32(devpwr, 0x70, 0x6001);

  // Enable hardware monitor (and setup like award)
  pci_write_config8(devpwr, 0x74, 0x01);

  // set IO base address to 0x5000
  pci_write_config32(devpwr, 0x90, 0x5001);

  // Enable SMBus 
  pci_write_config8(devpwr, 0xd2, 0x01);

  //
  // IDE setup
  //
  if (conf->enable_native_ide) {
    // Run the IDE controller in 'compatiblity mode - i.e. don't use PCI
    // interrupts.  Using PCI ints confuses linux for some reason.
	  
    enables = pci_read_config8(dev1, 0x42);
    printk_debug("enables in reg 0x42 0x%x\n", enables);
    enables &= ~0xc0;		// compatability mode
    pci_write_config8(dev1, 0x42, enables);
    enables = pci_read_config8(dev1, 0x42);
    printk_debug("enables in reg 0x42 read back as 0x%x\n", enables);
  }

  enables = pci_read_config8(dev1, 0x40);
  printk_debug("enables in reg 0x40 0x%x\n", enables);
  enables |= 3;
  pci_write_config8(dev1, 0x40, enables);
  enables = pci_read_config8(dev1, 0x40);
  printk_debug("enables in reg 0x40 read back as 0x%x\n", enables);

  // Enable prefetch buffers
  enables = pci_read_config8(dev1, 0x41);
  enables |= 0xf0;
  pci_write_config8(dev1, 0x41, enables);

  // Lower thresholds (cause award does it)
  enables = pci_read_config8(dev1, 0x43);
  enables &= ~0x0f;
  enables |=  0x05;
  pci_write_config8(dev1, 0x43, enables);

  // PIO read prefetch counter (cause award does it)
  pci_write_config8(dev1, 0x44, 0x18);

  // Use memory read multiple
  pci_write_config8(dev1, 0x45, 0x1c);

  // address decoding. 
  // we want "flexible", i.e. 1f0-1f7 etc. or native PCI
  // kevinh@ispiri.com - the standard linux drivers seem ass slow when 
  // used in native mode - I've changed back to classic
  enables = pci_read_config8(dev1, 0x9);
  printk_debug("enables in reg 0x9 0x%x\n", enables);
  // by the book, set the low-order nibble to 0xa. 
  if (conf->enable_native_ide) {
    enables &= ~0xf;
    // cf/cg silicon needs an 'f' here. 
    enables |= 0xf;
  } else {
    enables &= ~0x5;
  }

  pci_write_config8(dev1, 0x9, enables);
  enables = pci_read_config8(dev1, 0x9);
  printk_debug("enables in reg 0x9 read back as 0x%x\n", enables);

  // standard bios sets master bit. 
  enables = pci_read_config8(dev1, 0x4);
  printk_debug("command in reg 0x4 0x%x\n", enables);
  enables |= 7;
	
  // No need for stepping - kevinh@ispiri.com
  enables &= ~0x80;

  pci_write_config8(dev1, 0x4, enables);
  enables = pci_read_config8(dev1, 0x4);
  printk_debug("command in reg 0x4 reads back as 0x%x\n", enables);

  if (! conf->enable_native_ide) {
    // Use compatability mode - per award bios
    pci_write_config32(dev1, 0x10, 0x0);
    pci_write_config32(dev1, 0x14, 0x0);
    pci_write_config32(dev1, 0x18, 0x0);
    pci_write_config32(dev1, 0x1c, 0x0);
	  
    // Force interrupts to use compat mode - just like Award bios
    pci_write_config8(dev1, 0x3d, 00);
    pci_write_config8(dev1, 0x3c, 0xff);
  }


  ethernet_fixup();

  // Start the rtc
  rtc_init(0);
}

static void 
southbridge_init(struct chip *chip, enum chip_pass pass)
{

  struct southbridge_via_vt8231_config *conf = 
    (struct southbridge_via_vt8231_config *)chip->chip_info;

  switch (pass) {
  case CONF_PASS_POST_PCI:
    vt8231_init(conf);
    break;

  default:
    /* nothing yet */
    break;
  }
}

struct chip_control southbridge_via_vt8231_control = {
  enable: southbridge_init,
  name:   "VIA vt8231"
};