summaryrefslogtreecommitdiff
path: root/src/superio/nuvoton/nct5104d/superio.c
blob: 09ec34b79a2685b817379c86ecc292a6e47c8479 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
/* SPDX-License-Identifier: GPL-2.0-or-later */

#include <stdlib.h>
#include <console/console.h>
#include <device/pnp.h>
#include <device/device.h>
#include <superio/conf_mode.h>

#include "nct5104d.h"
#include "chip.h"

static void set_irq_trigger_type(struct device *dev, bool trig_level)
{
	u8 reg10, reg11, reg26;

	//Before accessing CR10 OR CR11 Bit 4 in CR26 must be set to 1
	reg26 = pnp_read_config(dev, GLOBAL_OPTION_CR26);
	reg26 |= CR26_LOCK_REG;
	pnp_write_config(dev, GLOBAL_OPTION_CR26, reg26);

	switch (dev->path.pnp.device) {
	//SP1 (UARTA) IRQ type selection (1:level,0:edge) is controlled by CR 10, bit 5
	case NCT5104D_SP1:
		reg10 = pnp_read_config(dev, IRQ_TYPE_SEL_CR10);
		if (trig_level)
			reg10 |= (1 << 5);
		else
			reg10 &= ~(1 << 5);
		pnp_write_config(dev, IRQ_TYPE_SEL_CR10, reg10);
		break;
	//SP2 (UARTB) IRQ type selection (1:level,0:edge) is controlled by CR 10, bit 4
	case NCT5104D_SP2:
		reg10 = pnp_read_config(dev, IRQ_TYPE_SEL_CR10);
		if (trig_level)
			reg10 |= (1 << 4);
		else
			reg10 &= ~(1 << 4);
		pnp_write_config(dev, IRQ_TYPE_SEL_CR10, reg10);
		break;
	//SP3 (UARTC) IRQ type selection (1:level,0:edge) is controlled by CR 11, bit 5
	case NCT5104D_SP3:
		reg11 = pnp_read_config(dev,IRQ_TYPE_SEL_CR11);
		if (trig_level)
			reg11 |= (1 << 5);
		else
			reg11 &= ~(1 << 5);
		pnp_write_config(dev, IRQ_TYPE_SEL_CR11, reg11);
		break;
	//SP4 (UARTD) IRQ type selection (1:level,0:edge) is controlled by CR 11, bit 4
	case NCT5104D_SP4:
		reg11 = pnp_read_config(dev,IRQ_TYPE_SEL_CR11);
		if (trig_level)
			reg11 |= (1 << 4);
		else
			reg11 &= ~(1 << 4);
		pnp_write_config(dev, IRQ_TYPE_SEL_CR11, reg11);
		break;
	default:
		break;
	}

	//Clear access control register
	reg26 = pnp_read_config(dev, GLOBAL_OPTION_CR26);
	reg26 &= ~CR26_LOCK_REG;
	pnp_write_config(dev, GLOBAL_OPTION_CR26, reg26);
}

static void route_pins_to_uart(struct device *dev, bool to_uart)
{
	u8 reg;

	reg = pnp_read_config(dev, 0x1c);

	switch (dev->path.pnp.device) {
	case NCT5104D_SP3:
	case NCT5104D_GPIO0:
		/* Route pins 33 - 40. */
		if (to_uart)
			reg |= (1 << 3);
		else
			reg &= ~(1 << 3);
		break;
	case NCT5104D_SP4:
	case NCT5104D_GPIO1:
		/* Route pins 41 - 48. */
		if (to_uart)
			reg |= (1 << 2);
		else
			reg &= ~(1 << 2);
		break;
	default:
		break;
	}

	pnp_write_config(dev, 0x1c, reg);
}

static void reset_gpio_default_in(struct device *dev)
{
	pnp_set_logical_device(dev);
	/*
	 * Soft reset GPIOs to default state: IN.
	 * The main GPIO LDN holds registers that configure the pins as output
	 * or input. These registers are located at offset 0xE0 plus the GPIO
	 * bank number multiplied by 4: 0xE0 for GPIO0, 0xE4 for GPIO1 and
	 * 0xF8 for GPIO6.
	 */
	pnp_write_config(dev, NCT5104D_GPIO0_IO + (dev->path.pnp.device >> 8) * 4, 0xFF);
}

static void reset_gpio_default_od(struct device *dev)
{
	struct device *gpio0, *gpio1, *gpio6;

	pnp_set_logical_device(dev);

	gpio0 = dev_find_slot_pnp(dev->path.pnp.port, NCT5104D_GPIO0);
	gpio1 = dev_find_slot_pnp(dev->path.pnp.port, NCT5104D_GPIO1);
	gpio6 = dev_find_slot_pnp(dev->path.pnp.port, NCT5104D_GPIO6);

	/*
	 * Soft reset GPIOs to default state: Open-drain.
	 * The NCT5104D_GPIO_PP_OD LDN holds registers (1 for each GPIO bank)
	 * that configure each GPIO pin to be open dain or push pull. System
	 * reset is known to not reset the values in this register. The
	 * registers are located at offsets begginign from 0xE0 plus GPIO bank
	 * number, i.e. 0xE0 for GPIO0, 0xE1 for GPIO1 and 0xE6 for GPIO6.
	 */
	if (gpio0 && gpio0->enabled)
		pnp_write_config(dev,
				 (gpio0->path.pnp.device >> 8) + NCT5104D_GPIO0_PP_OD, 0xFF);

	if (gpio1 && gpio1->enabled)
		pnp_write_config(dev,
				 (gpio1->path.pnp.device >> 8) + NCT5104D_GPIO0_PP_OD, 0xFF);

	if (gpio6 && gpio6->enabled)
		pnp_write_config(dev,
				 (gpio6->path.pnp.device >> 8) + NCT5104D_GPIO0_PP_OD, 0xFF);
}

static void disable_gpio_io_port(struct device *dev)
{
	struct device *gpio0, *gpio1, *gpio6;

	/*
	 * Since UARTC and UARTD share pins with GPIO0 and GPIO1 and the
	 * GPIO/UART can be selected via Kconfig, check whether at least one of
	 * GPIOs is enabled and if yes keep the GPIO IO VLDN enabled. If no
	 * GPIOs are enabled, disable the VLDN in order to protect from invalid
	 * devicetree + Kconfig settings.
	 */
	gpio0 = dev_find_slot_pnp(dev->path.pnp.port, NCT5104D_GPIO0);
	gpio1 = dev_find_slot_pnp(dev->path.pnp.port, NCT5104D_GPIO1);
	gpio6 = dev_find_slot_pnp(dev->path.pnp.port, NCT5104D_GPIO6);

	if (!((gpio0 && gpio0->enabled) || (gpio1 && gpio1->enabled) ||
	      (gpio6 && gpio6->enabled))) {
		dev->enabled = 0;
		printk(BIOS_WARNING, "WARNING: GPIO IO port configured,"
				     " but no GPIO enabled. Disabling...");
	}
}

static void nct5104d_init(struct device *dev)
{
	struct superio_nuvoton_nct5104d_config *conf = dev->chip_info;

	if (!dev->enabled)
		return;

	pnp_enter_conf_mode(dev);

	switch (dev->path.pnp.device) {
	case NCT5104D_SP1:
	case NCT5104D_SP2:
		set_irq_trigger_type(dev, conf->irq_trigger_type != 0);
		break;
	case NCT5104D_SP3:
	case NCT5104D_SP4:
		route_pins_to_uart(dev, true);
		set_irq_trigger_type(dev, conf->irq_trigger_type != 0);
		break;
	case NCT5104D_GPIO0:
	case NCT5104D_GPIO1:
		route_pins_to_uart(dev, false);
		/* FALLTHROUGH */
	case NCT5104D_GPIO6:
		if (conf->reset_gpios)
			reset_gpio_default_in(dev);
		break;
	case NCT5104D_GPIO_PP_OD:
		if (conf->reset_gpios)
			reset_gpio_default_od(dev);
		break;
	case NCT5104D_GPIO_IO:
		disable_gpio_io_port(dev);
		break;
	default:
		break;
	}

	pnp_exit_conf_mode(dev);
}

static struct device_operations ops = {
	.read_resources   = pnp_read_resources,
	.set_resources    = pnp_set_resources,
	.enable_resources = pnp_enable_resources,
	.enable           = pnp_alt_enable,
	.init             = nct5104d_init,
	.ops_pnp_mode     = &pnp_conf_mode_8787_aa,
};

static struct pnp_info pnp_dev_info[] = {
	{ NULL, NCT5104D_FDC,  PNP_IO0 | PNP_IRQ0, 0x07f8, },
	{ NULL, NCT5104D_SP1,  PNP_IO0 | PNP_IRQ0, 0x07f8, },
	{ NULL, NCT5104D_SP2,  PNP_IO0 | PNP_IRQ0, 0x07f8, },
	{ NULL, NCT5104D_SP3,  PNP_IO0 | PNP_IRQ0, 0x07f8, },
	{ NULL, NCT5104D_SP4,  PNP_IO0 | PNP_IRQ0, 0x07f8, },
	{ NULL, NCT5104D_GPIO_WDT},
	{ NULL, NCT5104D_GPIO0},
	{ NULL, NCT5104D_GPIO1},
	{ NULL, NCT5104D_GPIO6},
	{ NULL, NCT5104D_GPIO_PP_OD},
	{ NULL, NCT5104D_GPIO_IO, PNP_IO0, 0x07f8, },
	{ NULL, NCT5104D_PORT80},
};

static void enable_dev(struct device *dev)
{
	pnp_enable_devices(dev, &ops, ARRAY_SIZE(pnp_dev_info), pnp_dev_info);
}

struct chip_operations superio_nuvoton_nct5104d_ops = {
	CHIP_NAME("Nuvoton NCT5104D Super I/O")
	.enable_dev = enable_dev,
};